Included with this TV are the following accessories:
1 x User Guide
User Guide
1 x Quick Start Guide
Quick Start
Guide
1 x RF Cable
1 x Remote Control
2 x AAA Batteries
1 x TV
1 x Blanking plate for use when
wall mounting
Please save your packaging as you will need this in the event of warranty/service repair or support. We
are unable to carry out warranty/service if you are unable to package it correctly. The safest way to
package your item in the event of warranty/service repair is in it’s original box/packaging.
8
1 x Stand plus screws
(4 x screws for stand base plate
1 x screw for stability)
9
Attaching/Detaching the stand and wall mounting
ATTACHING THE STAND
1) Insert the stand (PART A) into the stand neck (PART B)
2) Use the assembly screws to fasten the stand base securely.
Make sure that the screws are securely tightened.
DETACHING THE STAND
Detaching the Stand
1) Remove the screws highlighted
2) Although there are no live parts exposed when removing
the stand, (in the event of wall mounting the TV) for aesthetic
purposes, included in the accessory pack is a cover plate which can
be clipped into the underside of the TV.
IMPORTANT - Before drilling any holes in the wall
ensure you are not drilling where there could be
any electric wires, water or gas pipes.
Wall mounting the TV
This television requires a VESA 400 x 200 wall mount, or equivalent.
1) Remove the four screws highlighted below.
2) The wall mount can now be easily attached to the mounting holes on the rear of the TV. These holes
are indicated in the picture below.
fi g 1
INCORRECT
CORRECT
TV
For optimum viewing, if wall mounting the TV higher than eye level, the TV should be
tilted downwards so that the TV’s screen is ‘face on’. See fi g 1 and 2
Important – If wall mounting this TV, only use the screws already provided in the wall mounting holes.
Using other screws which are longer could cause irreparable damage to internal parts.
Max length is 12mm
Viewing angle
fi g 2
Viewing angle
9
Important installation instructions
IMPORTANT INSTALLATION INSTRUCTIONS
WARNING
To prevent injury, this apparatus must be securely attached to the fl oor, wall or
TV cabinet in accordance with these installation instructions
Securing the TV to a Desk/ TV Stand
Image shown may differ from your TV. The TV
must be attached to desk so it cannot be pulled in
injury or damaging the product. Use only the screw
supplied.
Using the screw provided, screw through the hole
•
in the TV base to secure the TV to the desk/stand.
TV base
Desk/TV stand
Securing the TV to a Wall
• Position the TV close to the wall to avoid the
possibility of it falling when pushed.
• The instructions shown below are a safer way to
set up the TV, by fi xing it tothe wall, avoiding the
possibility of it falling forwards if pulled. This will
prevent the TV from falling forward and causing
injury. This will also prevent the TV from damage.
• This method is used if the TV is placed on a glass
surface or you do not wish to screw anything
into your furniture.
• Ensure that children do not climb or hang onto
the TV.
For this type of installation you will need a
fastening chord
(available free of charge from the helpline)
A) Using one/both of the top wall-mounting holes
and screws (the screws are already supplied in the
wall mounting holes) fasten one end of the
fastening chord/s to the TV.
B) Secure the other end of the fastening chord/s to
your wall. (you will need screws/fi xings suitable for
your wall type - available separately from most
DIY stores)
10
11
Getting Started - Initial Set Up
GETTING STARTED - INITIAL SET UP
1) Using the RF cable supplied, connect the TV
to the TV Aerial wall socket (Fig A)
Fig A
3) Switch on the television using the
power on/off switch.
Power on/off
2) Connect the power cable to the Electrical
outlet (Fig B)
Fig B
4) Insert the batteries supplied into the
Remote control and press the Standby
button to power on the TV
5) You will now be welcomed with the initial
set-up screen.
If it does not appear, on the remote control,
please press [MENU] then 8-8-8-8 and the
menu will appear.
Press OK on the remote control and tuning
will start.
If you are missing channels, the reason for this is likely to be signal strength, you should
consider connecting signal booster and re-tuning the TV.
Tip: If the TV fi nds some, but not all, of the Digital channels, the TV is functioning correctly but the
signal being received is not strong enough. (The signal strength needs to be above 85% - you can see the
signal strength the TV is receiving when you change channels/ programmes) you will need to increase
the signal reception in order to receive all of the channels available. The most economical way to do
this is by purchasing and connecting a ‘signal booster’ in between the TV and the TV aerial socket. If this
does not solve the problem, you will need to upgrade the TV aerial to a digital hi-gain compatible aerial
6) After tuning the following screen will
appear.
11
TV Buttons and Source Menu
TV BUTTONS & SOURCE MENU
Eject
1
2
Pause/Play
3
Displays the input source menu
4
Displays Menu/OSD
Volume up and menu right
5
6
Volume down and menu left
Programme/Channel up and menu up
7
8
Programme/Channel down and menu down
9
Standby Power On/Off
1
2
3
4
Choosing Mode Input/Source
To switch between the different input/
connections.
A) Using the buttons on the remote control:
1) Press [SOURCE/ AV] - The source menu will
appear
2) Press [\/] or [/\] to select the input you
require.
3) Press [OK]
5
6
7
8
9
B) Using the buttons on the Television:
1) Press [SOURCE]
2) Scroll up / down using CH+/ CH- buttons to
the input/source you require
3) Press Vol+ to change input/source to the
one selected.
12
13
Remote Control
REMOTE CONTROL
STANDBY - Switch on TV when in standby or vice versa
1
MUTE - Mute the sound or vice versa
TV/RADIO - Switch to Freeview and switch between TV and
radio in Freeview mode
TV GUIDE - Opens the 7 Day TV Guide (Freeview mode)
ATV - Switch to analogue TV source
USB - Switch to USB source
DVD - Switch to DVD source
EJECT - Eject disc in DVD mode
REC - To record what is currently on television
2
REC LIST - Opens the list of what you have previously recorded
- To restart the current chapter
- To advance forward to the next chapter
- To stop the playback
- To play in fast rewind mode
- To play in fast forward mode
- To play/pause (Pause live TV when USB Memory Stick is
inserted)
SOURCE/AV - To display the input/source menu
3
INFO - Press once for now/next channel information
Press twice for programme information about current
programme
and adjust the system settings to your preference
MENU - To display OSD menu
EXIT - To exit all menus
NUMBER BUTTONS - 0 – 9 to select a TV channel directly.
- To return to the previous channel viewed
FAV - To display favourites menu
- Allows you to navigate the on-screen menus
1
2
3
VOL - To increase / decrease the sound level
4
SUBTITLE - To switch the dialogue at the bottom of the screen
(on/off)
ASPECT - To switch the screen between the different picture
formats
AUDIO - To change the audio language (if available)
SLEEP - Press repeatedly to cycle through the sleep options
CH To increase or decrease the channel being watched
GOTO - DVD mode - To go to a specifi c chapter
A-B - DVD mode - Press once to set point, press a second time to
return to point
ANGLE - DVD mode - Select different angle of DVD (if available)
REPEAT - DVD mode - To repeat playback
D.DIS - DVD mode - To display the current disc information
5
ZOOM - DVD mode - To zoom in
SIZE - Teletext mode* - To change the display size in Teletext
mode
DISPLAY - To switch off the screen when listening to radio
DVD SETUP/TEXT - DVD mode - To display the DVD setup menu
Teletext mode* - To enter Teletext
D.MENU/INDEX - DVD mode - To display the DVD disc menu
Teletext mode* - To display the index page
TITLE/REVEAL - DVD mode - To display the DVD title menu
Teletext mode* - To reveal or hide the hidden words.
HOLD - Teletext mode - Hold current page which is displayed
* Teletext function is only available in analogue
4
5
13
Loading...
+ 23 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.