Ferguson 8600 Service Manual
2
1
Introduction
1
TABLE OF CONTENTS
1A10 - 8600 series tractors - General
1A11 - 8600 series tractors - Error codes
1A12 - 8600 series tractors - Diagrams and plans
Chapter 1
1A13 - Section intentionally left blank
1A14 - Section intentionally left blank
1A15 - Section intentionally left blank
1A16 - 8600 series tractors - Adjustments, bleeding and calibrations
1A17 - Section intentionally left blank
1A18 - Section intentionally left blank
Massey Ferguson 8600 i
Table of contents
ii Massey Ferguson 8600
8600 series tractors - General
1A10
1A10
8600 series tractors - General
3
TABLE OF CONTENTS
A. Using the manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
B. General specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
C. Forward speeds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
D. Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
E. Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
F. Conversion table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
G. Retaining compounds and sealing products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Massey Ferguson 8600 - Issue 1A10.1
8600 series tractors - General
1A10.2 Massey Ferguson 8600 - Issue
8600 series tractors - General
A.
Using the manual
General
The purpose of this manual is to assist Dealers and
Agents in the efficient installation, servicing and repair of
Massey Ferguson equipment. If the procedures are carried out as detailed and specialised tools are used where
appropriate, the operations should be completed within
the times stated in the repair time schedule.
Structure of the manual
Page numbering
This manual is divided into chapters and sections, each
page containing the following information:
Example: 10A12.1
10 Chap ter
A Subset letter
1- Subset order number
2 Subset number
1- Page number within the section
The issue number is indicated at the bottom of the page.
Contents
For quick reference, each chapter starts with a table of
contents, listing the various sections included in that
chapter.
Meaning of reference numbers
(..) reference for parts and components
Service tools
Where the use of a service tool is necessary to carry out
an operation, the tool reference is mentioned with the relevant instruction.
Tool drawings for makeshift tools are given at the end of
the relevant sections.
Repairs and parts replacement
When parts have to be replaced, it is essential that only
genuine Massey Ferguson parts are used.
The following points are of particular importance when
carrying out repairs and fitting replacement parts and accessories. Tractor safety may be compromised if non-genuine parts are fitted.
Legislation in certain countries prohibits the fitting of
parts that do not comply with the tractor manufacturer's
specifications. Torque wrench setting figures given in the
workshop manual must be strictly adhered to. Locking devices must be fitted where specified. If the efficiency of
a locking device is impaired during disassembly, it must
be replaced.
The tractor warranty may be invalidated if non-genuine
Massey Ferguson parts are fitted. All Massey Ferguson
parts are guaranteed by the manufacturer. Massey Ferguson Dealers and Agents are required to supply genuine
parts only.
Model 8650
Engine
Brand SISU
Ty pe 84CTA
Nominal power (ISO TR14396) at 2200 rpm 240 hp
Maximum power (ISO TR14396) at 2000 rpm 270 hp
Maximum torque (ISO TR14396) 1185 Nm
Nominal PTO power (OECD) at 2200 rpm 205 hp
Maximum PTO power (OECD) at PTO 1000 rpm 225 hp
Idle speed 800 rpm
Maximum speed 2260 rpm
Engine weight 665 kg
Number of cylinders 6
Engine cubic capacity 8,4 l
Piston travel 145 mm
Piston diameter 111 mm
Compression ratio 16,7 bar ± 0,5 bar
Compression pressure 24 bar
Injection pump brand Bosch
Injection pump type CP 3.3
Firing order 1-5-3-6-2-4
Maximum pressure in the high-pressure system 1400 bar
Injector brand Bosch
Injector type CRIN 2/8 holes
Massey Ferguson 8600 - Issue 1A10.3
8600 series tractors - General
Engine
Charge pump type Electric
Fuel prefilter filtration capacity 30 μ
Main fuel filter filtration capacity 5 μ
Low-pressure system pressure at minimum speed 0,75 bar
Low-pressure system pressure at maximum speed 0,75 bar
Recommended oil: CI-4 (ACEA and API)
Maximum operating tilt (precautions) Oil/fuel consumption Maximum 0.1%
Lubrication system Gear pump at the bottom of the timing
Oil cooling system Cooler integrated into the engine (left side)
Oil pressure at minimum speed 1 bar
Oil pressure at maximum speed 2,5 bar at 5 bar depending on the temperature
Relief valve adjustment pressure 5 bar (spring pressure)
Air suction type Turbocharged with air/air intercooler
Air preheating type Grid heater with relay controlled by the ECU
Number of valves 24
Valve clearance value 0,35 mm (inlet and exhaust)
Engine cooling system Water cooling
Fan type Vistronic fan
Thermostat begins to open at 83 °C
Liquid temperature from - to - 35 °C to 108 °C
Air compressor brand for the brake system Knorr
Type of compressor Piston
Pressure range: 6,5 bar to 8 bar
Block preheater 110 or 220 volts
Fuel preheater Accessory kit available
Urea preheater Urea system and cab heating in parallel
Gas recycling system Internal EGR or SCR system
Internal EGR system Additional intake cam
SCR system (AdBlue/DEF injection) Exhaust outlet treatment system
Safety system Quality sensor in the tank
Device brand Bosch
Type of control Bosch controller
Main filter filtration capacity Secondary filter filtration capacity Tertiary filter filtration capacity Urea solidification temperature - 11 °C
Belt: air conditioning compressor/left-hand alternator/air compres-
sor (2 dimensions: with or without air compressor)
Belt: fan/right-hand alternator/air compressor (2 dimensions: a dif-
ferent fan pulley is used depending on the power)
Poly V 6 rib belt
Poly V 12 rib belt
Rear axle transmission
Gearbox type Continuous variation
Transmission type ML 260
Number of ranges 2 ranges (hare and tortoise)
Maximum speed 40 km/h or 50 km/h
Number of creeper gears No creeper gears
Rear axle type HA 260
1A10.4 Massey Ferguson 8600 - Issue
8600 series tractors - General
Rear axle transmission
Number of pinion/ring gear teeth 12/43
Rear axle ratio (crownwheel and pinion) 32.967
4WD ratio 0.68
Final drive type Epicyclic
Final drive reduction ratio 9.2 (123+15/15)
Maximum 4WD clutch torque 330 daNm
Number of 4WD discs 8 discs
Main brake type 10" oil-immersed disc
Number of discs 6 discs
Braking pressure 0 to 60 bar
Parking brake type ParkLock (electrical/hydraulic)
Trailer brake type Hydraulic and pneumatic
Pneumatic trailer braking pressure 6,5 bar to 8 bar
Hydraulic trailer braking pressure 0 to 150 bar
Maximum operating tilt 25° pitch (front/rear)
25° roll (right/left)
17° combined
Transmission preheater 110 volts/150 watt
Total loaded weight supported by rear axle 40 km/h : 12000 kg
50 km/h : 10000 kg
Front axle
Front axle brand DANA
Axle type Suspended or fixed
Supplier reference Fixed: 770/504
Suspended: 770/612
Rotational direction Clockwise
Front axle weight Fixed: 765 kg
Suspended: 1066 kg
Total loaded weight supported by front axle 40 kph: 9000 kg
50 kph: 7500 kg
Recommended oil type (beam and final drive) SAE 85 W 90 (API GL5)
Total ratio for front axle 16.862
Number of teeth on final drive 14 x 35 x 85
Final drive ratio 7. 0 7 1
Number of pinion/ring gear teeth 13/31
Number of differential discs 15 discs
Maximum steering angle 55°
Oscillation angle Type of oscillation stop Mechanical
Steering ram diameter 45 mm x 90 mm
Steering ram stroke 2 x 143,5 mm
Suspension type Hydraulics
Suspension ram diameter 90 mm x 100 mm
Suspension ram stroke 10 0 mm
Hydraulic control unit brand Husco
Hydraulic control unit nominal pressure 200 bar
Number of accumulators 2
Massey Ferguson 8600 - Issue 1A10.5
8600 series tractors - General
Front axle
Accumulator pressure Left 1 l : 10 bar
Right 1,4 l : 50 bar
Suspension sensor type Angular potentiometer.
Steering sensor type Angular potentiometer.
Brake type Combined with the rear brake
Factor K 1.331
Electrohydraulic
System type Load Sensing
Flow rate 175 l/min
High-pressure pump type Sauer Danfoss piston pump
High-pressure pump displacement 75 cm³
High-pressure pump rotational speed 2200 rpm
High-pressure pump maximum flow rate 200 l/min
High-pressure pump maximum pressure 200 bar
Maximum quantity of oil to add for heavy implements 16 l
Maximum exportable oil quantity (without adding oil) 64 l
Maximum exportable oil quantity (adding oil) 74 l
Charge pump type Gravity
Main relief valve adjustment pressure 200 bar ± 10 bar
Number of spool valves (maximum) 8
Number of front "push-pull" connectors 4 connectors i.e. 2 spool valves
Number of rear "push-pull" connectors 12 connectors i.e. 6 spool valves
Maximum flow rate per spool valve 100 l/min
Spool valve control type Electric
Recommended oil: According to MF CMS M1145 specification
Steering
Steering type Hydrostatic
Type of control Steering wheel or steering wheel + electrohydraulic spool valves
Orbitrol displacement 315 cm³
Steering ram diameter 90 mm x 45 mm
Steering ram stroke 2 x 143,5 mm
Working pressure 175 bar ± 5 bar
Pressure relief valve adjustment pressure 175 bar ± 5 bar
Shock valve adjustment pressure 240 bar
Oil recommended for steering According to MF CMS M1145 specification
Linkage
Rear lift ram diameter 105 mm
Rear linkage travel 788 mm or 860 mm
Maximum lifting capacity at ball joints (rear) 10000 kg
Operating pressure (rear) 180 bar
3-point linkage category (rear) 3 or 4
Front lift ram diameter 100 mm x 50 mm
Front linkage travel 216 mm ± 1,5 mm
1A10.6 Massey Ferguson 8600 - Issue
8600 series tractors - General
Linkage
Maximum lifting capacity at ball joints (front) 5000 kg
Operating pressure (front) 180 bar
3-point linkage category (front) 3
Rear power take-off (PTO)
Number of selections possible for rear PTO 540/1000 or 540E/1000
Maximum permissible power 540/540E in 1"3/8 (6 and 21 splines) 100 hp
Maximum permissible power 540/540E in 1"3/4 (20 splines) 160 hp
Maximum permissible power 1000 in 1"3/8 (6 and 21 splines) 180 hp
Maximum permissible power 1000 in 1"3/4 (20 splines) 239 hp
Engine speed if PTO 540 2037 rpm
Engine speed if PTO 540 eco 1598 rpm
Engine speed if PTO 1000 2031 rpm
Rotational direction Clockwise
Clutch type Hydraulics
Number of clutch discs 8 discs
Control pressure 18 bar
Splined shaft type 6 and 21 in 1"3/8 and 20 in 1"3/4
Front power take-off
Number of selections possible for front PTO 1000 rpm
Maximum permissible power Clockwise: 147 hp
Anti-clockwise: 221 hp
Maximum permissible torque Clockwise: 1000 Nm
Anti-clockwise: 1500 Nm
Rotational direction 2 directions of rotation
Engine speed if PTO 1000 2040 rpm
Ratio 2.04
Clutch type Hydraulics
Splined shaft type 6 and 21 in 1"3/8
Electric
Battery brand TAB
Battery specifications (2 batteries) 12 V - 105 A/H
Ma ximum cu rrent a t start - up (IEC s tandar d) 1010 A
Starter type 12 V noseless
Starter power 4.2 kW
Alternator type 2 x 14 V/80 A (160 A) or 2 x 14 V/120 A (240 A)
Current available on ISOBUS connector 50 A
Electronics
Function of each controller
DCC3 Instrument panel
AUTO 4 Transmission
4 AUTO 5 DC Linkage/ParkLock/Suspended front axle/Armrest/Semi-active cab
PVG 32 valves Electrohydraulic spool valves
Lights module User interface for lights
Lighting controller Lighting control
Massey Ferguson 8600 - Issue 1A10.7
8600 series tractors - General
Electronics
1 ECM Tier 3 SISU Engine
1 Orbitrol Danfoss valve Orbitrol for the Auto-Guide function
Data 4 Onboard computer
Automatic air conditioning module Air conditioning
DCU Denoxtronic module
Cab and fittings
Type of cab suspension available Passive
Semi-active
Type of rear-view mirror control available Manual or automatic
Type of air conditioning control available Manual or automatic
Type and brand of air conditioning compressor SANDEN with axial pistons
Compressor displacement 154.9 cm3/rev.
Refrigerant R134a
Cab noise level 71 DBA
Roof type Standard or with window
Model 8660
Engine
Brand SISU
Ty p e 84CTA
Nominal power (ISO TR14396) at 2200 rpm 265 hp
Maximum power (ISO TR14396) at 2000 rpm 295 hp
Maximum torque (ISO TR14396) 1295 Nm
Nominal PTO power (OECD) at 2200 rpm 225 hp
Maximum PTO power (OECD) at PTO 1000 rpm 250 hp
Idle speed 800 rpm
Maximum speed 2260 rpm
Engine weight 665 kg
Number of cylinders 6
Engine cubic capacity 8,4 l
Piston travel 145 mm
Piston diameter 111 m m
Compression ratio 16,7 bar ± 0,5 bar
Compression pressure 24 bar
Injection pump brand Bosch
Injection pump type CP 3.3
Firing order 1-5-3-6-2-4
Maximum pressure in the high-pressure system 1400 bar
Injector brand Bosch
Injector type CRIN 2/8 holes
Charge pump type Electric
Fuel prefilter filtration capacity 30 μ
Main fuel filter filtration capacity 5 μ
Low-pressure system pressure at minimum speed 0,75 bar
Low-pressure system pressure at maximum speed 0,75 bar
Recommended oil: CI-4 (ACEA and API)
Maximum operating tilt (precautions) -
1A10.8 Massey Ferguson 8600 - Issue
8600 series tractors - General
Engine
Oil/fuel consumption Maximum 0.1%
Lubrication system Gear pump at the bottom of the timing
Oil cooling system Cooler integrated into the engine (left side)
Oil pressure at minimum speed 1 bar
Oil pressure at maximum speed 2,5 bar at 5 bar depending on the temperature
Relief valve adjustment pressure 5 bar (spring pressure)
Air suction type Turbocharged with air/air intercooler
Air preheating type Grid heater with relay controlled by the ECU
Number of valves 24
Valve clearance value 0,35 mm (inlet and exhaust)
Engine cooling system Water cooling
Fan type Vistronic fan
Thermostat begins to open at 83 °C
Liquid temperature from - to - 35 °C to 108 °C
Air compressor brand for the brake system Knorr
Type of compressor Piston
Pressure range: 6,5 bar to 8 bar
Block preheater 110 or 220 volts
Fuel preheater Accessory kit available
Urea preheater Urea system and cab heating in parallel
Gas recycling system Internal EGR or SCR system
Internal EGR system Additional intake cam
SCR system (AdBlue/DEF injection) Exhaust outlet treatment system
Safety system Quality sensor in the tank
Device brand Bosch
Type of control Bosch controller
Main filter filtration capacity Secondary filter filtration capacity Tertiary filter filtration capacity Urea solidification temperature - 11 °C
Belt: air conditioning compressor/left-hand alternator/air compres-
sor (2 dimensions: with or without air compressor)
Belt: fan/right-hand alternator/air compressor (2 dimensions: a dif-
ferent fan pulley is used depending on the power)
Poly V 6 rib belt
Poly V 12 rib belt
Rear axle transmission
Gearbox type Continuous variation
Transmission type ML 260
Number of ranges 2 ranges (hare and tortoise)
Maximum speed 40 km/h or 50 km/h
Number of creeper gears No creeper gears
Rear axle type HA 260
Number of pinion/ring gear teeth 12/43
Rear axle ratio (crownwheel and pinion) 32.967
4WD ratio 0.68
Final drive type Epicyclic
Final drive reduction ratio 9.2 (123+15/15)
Maximum 4WD clutch torque 330 daNm
Number of 4WD discs 8 discs
Massey Ferguson 8600 - Issue 1A10.9
8600 series tractors - General
Rear axle transmission
Main brake type 10" oil-immersed disc
Number of discs 6 discs
Braking pressure 0 to 60 bar
Parking brake type ParkLock (electrical/hydraulic)
Trailer brake type Hydraulic and pneumatic
Pneumatic trailer braking pressure 6,5 bar to 8 bar
Hydraulic trailer braking pressure 0 to 150 bar
Maximum operating tilt 25° pitch (front/rear)
25° roll (right/left)
17° combined
Transmission preheater 110 volts/150 watt
Total loaded weight supported by rear axle 40 kph: 12000 kg
50 kph: 10000 kg
Front axle
Front axle brand DANA
Axle type Suspended or fixed
Supplier reference Fixed: 770/504
Suspended: 770/612
Rotational direction Clockwise
Front axle weight Fixed: 765 kg
Suspended: 1066 kg
Total loaded weight supported by front axle 40 kph: 9000 kg
50 kph: 7500 kg
Recommended oil type (beam and final drive) SAE 85 W 90 (API GL5)
Total ratio for front axle 16.862
Number of teeth on final drive 14 x 35 x 85
Final drive ratio 7. 0 7 1
Number of pinion/ring gear teeth 13/31
Number of differential discs 15 discs
Maximum steering angle 55°
Oscillation angle Type of oscillation stop Mechanical
Steering ram diameter 45 mm x 90 mm
Steering ram stroke 2 x 143,5 mm
Suspension type Hydraulics
Suspension ram diameter 90 mm x 100 mm
Suspension ram stroke 100 mm
Hydraulic control unit brand Husco
Hydraulic control unit nominal pressure 200 bar
Number of accumulators 2
Accumulator pressure Left 1 l : 10 bar
Right 1,4 l : 50 bar
Suspension sensor type Angular potentiometer.
Steering sensor type Angular potentiometer.
Brake type Combined with the rear brake
Factor K 1.331
1A10.10 Massey Ferguson 8600 - Issue
8600 series tractors - General
Electrohydraulic
System type Load Sensing
Flow rate 175 l/min
High-pressure pump type Sauer Danfoss piston pump
High-pressure pump displacement 75 cm³
High-pressure pump rotational speed 2200 rpm
High-pressure pump maximum flow rate 200 l/min
High-pressure pump maximum pressure 200 bar
Maximum quantity of oil to add for heavy implements 16 l
Maximum exportable oil quantity (without adding oil) 64 l
Maximum exportable oil quantity (adding oil) 74 l
Charge pump type Gravity
Main relief valve adjustment pressure 200 bar ± 10 bar
Number of spool valves (maximum) 8
Number of front "push-pull" connectors 4 connectors i.e. 2 spool valves
Number of rear "push-pull" connectors 12 connectors i.e. 6 spool valves
Maximum flow rate per spool valve 100 l/min
Spool valve control type Electric
Recommended oil: According to MF CMS M1145 specification
Steering
Steering type Hydrostatic
Type of control Steering wheel or steering wheel + electrohydraulic spool valves
Orbitrol displacement 315 cm³
Steering ram diameter 90 mm x 45 mm
Steering ram stroke 2 x 143,5 mm
Working pressure 175 bar ± 5 bar
Pressure relief valve adjustment pressure 175 bar ± 5 bar
Shock valve adjustment pressure 240 bar
Oil recommended for steering According to MF CMS M1145 specification
Linkage
Rear lift ram diameter 105 mm
Rear linkage travel 788 mm or 860 mm
Maximum lifting capacity at ball joints (rear) 10000 kg
Operating pressure (rear) 180 bar
3-point linkage category (rear) 3 or 4
Front lift ram diameter 100 mm x 50 mm
Front linkage travel 216 mm ± 1,5 mm
Maximum lifting capacity at ball joints (front) 5000 kg
Operating pressure (front) 180 bar
3-point linkage category (front) 3
Rear power take-off (PTO)
Number of selections possible for rear PTO 540/1000 or 540E/1000
Maximum permissible power 540/540E in 1"3/8 (6 and 21 splines) 100 hp
Maximum permissible power 540/540E in 1"3/4 (20 splines) 160 hp
Maximum permissible power 1000 in 1"3/8 (6 and 21 splines) 180 hp
Maximum permissible power 1000 in 1"3/4 (20 splines) 262 hp
Massey Ferguson 8600 - Issue 1A10.11
8600 series tractors - General
Rear power take-off (PTO)
Engine speed if PTO 540 2037 rpm
Engine speed if PTO 540 eco 1598 rpm
Engine speed if PTO 1000 2031 rpm
Rotational direction Clockwise
Clutch type Hydraulics
Number of clutch discs 8 discs
Control pressure 18 bar
Splined shaft type 6 and 21 in 1"3/8 and 20 in 1"3/4
Front power take-off
Number of selections possible for front PTO 1000 rpm
Maximum permissible power Clockwise: 147 hp
Anti-clockwise: 221 hp
Maximum permissible torque Clockwise: 1000 Nm
Anti-clockwise: 1500 Nm
Rotational direction 2 directions of rotation
Engine speed if PTO 1000 2040 rpm
Ratio 2.04
Clutch type Hydraulics
Splined shaft type 6 and 21 in 1"3/8
Electric
Battery brand TAB
Battery specifications (2 batteries) 12 V - 105 A/H
Maximum current at start-up (IEC standard) 1010 A
Starter type 12 V noseless
Starter power 4.2 kW
Alternator type 2 x 14 V/80 A (160 A) or 2 x 14 V/120 A (240 A)
Current available on ISOBUS connector 50 A
Electronics
Function of each controller
DCC3 Instrument panel
AUTO 4 Transmission
4 AUTO 5 DC Linkage/ParkLock/Suspended front axle/Armrest/Semi-active cab
PVG 32 valves Electrohydraulic spool valves
Lights module User interface for lights
Lighting controller Lighting control
1 ECM Tier 3 SISU Engine
1 Orbitrol Danfoss valve Orbitrol for the Auto-Guide function
Data 4 Onboard computer
Automatic air conditioning module Air conditioning
DCU Denoxtronic module
Cab and fittings
Type of cab suspension available Passive
Semi-active
Type of rear-view mirror control available Manual or automatic
1A10.12 Massey Ferguson 8600 - Issue
8600 series tractors - General
Cab and fittings
Type of air conditioning control available Manual or automatic
Type and brand of air conditioning compressor SANDEN with axial pistons
Compressor displacement 154.9 cm3/rev.
Refrigerant R134a
Cab noise level 71 DBA
Roof type Standard or with window
Model 8670
Engine
Brand SISU
Ty pe 84CTA
Nominal power (ISO TR14396) at 2200 rpm 290 hp
Maximum power (ISO TR14396) at 2000 rpm 320 hp
Maximum torque (ISO TR14396) 1400 Nm
Nominal PTO power (OECD) at 2200 rpm 250 hp
Maximum PTO power (OECD) at PTO 1000 rpm 275 hp
Idle speed 800 rpm
Maximum speed 2260 rpm
Engine weight 665 kg
Number of cylinders 6
Engine cubic capacity 8,4 l
Piston travel 145 mm
Piston diameter 111 mm
Compression ratio 16,7 bar ± 0,5 bar
Compression pressure 24 bar
Injection pump brand Bosch
Injection pump type CP 3.3
Firing order 1-5-3-6-2-4
Maximum pressure in the high-pressure system 1400 bar
Injector brand Bosch
Injector type CRIN 2/8 holes
Charge pump type Electric
Fuel prefilter filtration capacity 30 μ
Main fuel filter filtration capacity 5 μ
Low-pressure system pressure at minimum speed 0,75 bar
Low-pressure system pressure at maximum speed 0,75 bar
Recommended oil: CI-4 (ACEA and API)
Maximum operating tilt (precautions) Oil/fuel consumption Maximum 0.1%
Lubrication system Gear pump at the bottom of the timing
Oil cooling system Cooler integrated into the engine (left side)
Oil pressure at minimum speed 1 bar
Oil pressure at maximum speed 2,5 bar at 5 bar depending on the temperature
Relief valve adjustment pressure 5 bar (spring pressure)
Air suction type Turbocharged with air/air intercooler
Air preheating type Grid heater with relay controlled by the ECU
Number of valves 24
Valve clearance value 0,35 mm (inlet and exhaust)
Massey Ferguson 8600 - Issue 1A10.13
8600 series tractors - General
Engine
Engine cooling system Water cooling
Fan type Vistronic fan
Thermostat begins to open at 83 °C
Liquid temperature from - to - 35 °C to 108 °C
Air compressor brand for the brake system Knorr
Type of compressor Piston
Pressure range: 6,5 bar to 8 bar
Block preheater 110 or 220 volts
Fuel preheater Accessory kit available
Urea preheater Urea system and cab heating in parallel
Gas recycling system Internal EGR or SCR system
Internal EGR system Additional intake cam
SCR system (AdBlue/DEF injection) Exhaust outlet treatment system
Safety system Quality sensor in the tank
Device brand Bosch
Type of control Bosch controller
Main filter filtration capacity Secondary filter filtration capacity Tertiary filter filtration capacity Urea solidification temperature - 11 °C
Belt: air conditioning compressor/left-hand alternator/air compres-
sor (2 dimensions: with or without air compressor)
Belt: fan/right-hand alternator/air compressor (2 dimensions: a dif-
ferent fan pulley is used depending on the power)
Poly V 6 rib belt
Poly V 12 rib belt
Rear axle transmission
Gearbox type Continuous variation
Transmission type ML 260
Number of ranges 2 ranges (hare and tortoise)
Maximum speed 40 km/h or 50 km/h
Number of creeper gears No creeper gears
Rear axle type HA 260
Number of pinion/ring gear teeth 12/43
Rear axle ratio (crownwheel and pinion) 32.967
4WD ratio 0.68
Final drive type Epicyclic
Final drive reduction ratio 9.2 (123+15/15)
Maximum 4WD clutch torque 330 daNm
Number of 4WD discs 8 discs
Main brake type 10" oil-immersed disc
Number of discs 6 discs
Braking pressure 0 to 60 bar
Parking brake type ParkLock (electrical/hydraulic)
Trailer brake type Hydraulic and pneumatic
Pneumatic trailer braking pressure 6,5 bar to 8 bar
Hydraulic trailer braking pressure 0 to 150 bar
Maximum operating tilt 25° pitch (front/rear)
25° roll (right/left)
17° combined
1A10.14 Massey Ferguson 8600 - Issue
8600 series tractors - General
Rear axle transmission
Transmission preheater 110 volts/150 watt
Total loaded weight supported by rear axle 40 kph: 12000 kg
50 kph: 10000 kg
Front axle
Front axle brand DANA
Axle type Suspended or fixed
Supplier reference Fixed: 770/504
Suspended: 770/612
Rotational direction Clockwise
Front axle weight Fixed: 765 kg
Suspended: 1066 kg
Total loaded weight supported by front axle 40 kph: 9000 kg
50 kph: 7500 kg
Recommended oil type (beam and final drive) SAE 85 W 90 (API GL5)
Total ratio for front axle 16.862
Number of teeth on final drive 14 x 35 x 85
Final drive ratio 7. 0 7 1
Number of pinion/ring gear teeth 13/31
Number of differential discs 15 discs
Maximum steering angle 55°
Oscillation angle Type of oscillation stop Mechanical
Steering ram diameter 45 mm x 90 mm
Steering ram stroke 2 x 143,5 mm
Suspension type Hydraulics
Suspension ram diameter 90 mm x 100 mm
Suspension ram stroke 10 0 mm
Hydraulic control unit brand Husco
Hydraulic control unit nominal pressure 200 bar
Number of accumulators 2
Accumulator pressure Left 1 l : 10 bar
Right 1,4 l : 50 bar
Suspension sensor type Angular potentiometer.
Steering sensor type Angular potentiometer.
Brake type Combined with the rear brake
Factor K 1.331
Electrohydraulic
System type Load Sensing
Flow rate 175 l/min
High-pressure pump type Sauer Danfoss piston pump
High-pressure pump displacement 75 cm³
High-pressure pump rotational speed 2200 rpm
High-pressure pump maximum flow rate 200 l/min
High-pressure pump maximum pressure 200 bar
Maximum quantity of oil to add for heavy implements 16 l
Maximum exportable oil quantity (without adding oil) 64 l
Massey Ferguson 8600 - Issue 1A10.15
8600 series tractors - General
Electrohydraulic
Maximum exportable oil quantity (adding oil) 74 l
Charge pump type Gravity
Main relief valve adjustment pressure 200 bar ± 10 bar
Number of spool valves (maximum) 8
Number of front "push-pull" connectors 4 connectors i.e. 2 spool valves
Number of rear "push-pull" connectors 12 connectors i.e. 6 spool valves
Maximum flow rate per spool valve 100 l/min
Spool valve control type Electric
Recommended oil: According to MF CMS M1145 specification
Steering
Steering type Hydrostatic
Type of control Steering wheel or steering wheel + electrohydraulic spool valves
Orbitrol displacement 315 cm³
Steering ram diameter 90 mm x 45 mm
Steering ram stroke 2 x 143,5 mm
Working pressure 175 bar ± 5 bar
Pressure relief valve adjustment pressure 175 bar ± 5 bar
Shock valve adjustment pressure 240 bar
Oil recommended for steering According to MF CMS M1145 specification
Linkage
Rear lift ram diameter 105 mm
Rear linkage travel 788 mm or 860 mm
Maximum lifting capacity at ball joints (rear) 10000 kg
Operating pressure (rear) 180 bar
3-point linkage category (rear) 3 or 4
Front lift ram diameter 100 mm x 50 mm
Front linkage travel 216 mm ± 1,5 mm
Maximum lifting capacity at ball joints (front) 5000 kg
Operating pressure (front) 180 bar
3-point linkage category (front) 3
Rear power take-off (PTO)
Number of selections possible for rear PTO 540/1000 or 540E/1000
Maximum permissible power 540/540E in 1"3/8 (6 and 21 splines) 100 hp
Maximum permissible power 540/540E in 1"3/4 (20 splines) 160 hp
Maximum permissible power 1000 in 1"3/8 (6 and 21 splines) 180 hp
Maximum permissible power 1000 in 1"3/4 (20 splines) 283 hp
Engine speed if PTO 540 2037 rpm
Engine speed if PTO 540 eco 1598 rpm
Engine speed if PTO 1000 2031 rpm
Rotational direction Clockwise
Clutch type Hydraulics
Number of clutch discs 8 discs
Control pressure 18 bar
Splined shaft type 6 and 21 in 1"3/8 and 20 in 1"3/4
1A10.16 Massey Ferguson 8600 - Issue
8600 series tractors - General
Front power take-off
Number of selections possible for front PTO 1000 rpm
Maximum permissible power Clockwise: 147 hp
Anti-clockwise: 221 hp
Maximum permissible torque Clockwise: 1000 Nm
Anti-clockwise: 1500 Nm
Rotational direction 2 directions of rotation
Engine speed if PTO 1000 2040 rpm
Ratio 2.04
Clutch type Hydraulics
Splined shaft type 6 and 21 in 1"3/8
Electric
Battery brand TAB
Battery specifications (2 batteries) 12 V - 105 A/H
Ma ximum cu rrent a t start - up (IEC s tandar d) 1010 A
Starter type 12 V noseless
Starter power 4.2 kW
Alternator type 2 x 14 V/80 A (160 A) or 2 x 14 V/120 A (240 A)
Current available on ISOBUS connector 50 A
Electronics
Function of each controller
DCC3 Instrument panel
AUTO 4 Transmission
4 AUTO 5 DC Linkage/ParkLock/Suspended front axle/Armrest/Semi-active cab
PVG 32 valves Electrohydraulic spool valves
Lights module User interface for lights
Lighting controller Lighting control
1 ECM Tier 3 SISU Engine
1 Orbitrol Danfoss valve Orbitrol for the Auto-Guide function
Data 4 Onboard computer
Automatic air conditioning module Air conditioning
DCU Denoxtronic module
Cab and fittings
Type of cab suspension available Passive
Semi-active
Type of rear-view mirror control available Manual or automatic
Type of air conditioning control available Manual or automatic
Type and brand of air conditioning compressor SANDEN with axial pistons
Compressor displacement 154.9 cm3/rev.
Refrigerant R134a
Cab noise level 71 DBA
Roof type Standard or with window
Massey Ferguson 8600 - Issue 1A10.17
8600 series tractors - General
Model 8680
Engine
Brand SISU
Ty p e 84CTA
Nominal power (ISO TR14396) at 2200 rpm 320 hp
Maximum power (ISO TR14396) at 2000 rpm 350 hp
Maximum torque (ISO TR14396) 1492 Nm
Nominal PTO power (OECD) at 2200 rpm 275 hp
Maximum PTO power (OECD) at PTO 1000 rpm 300 hp
Idle speed 800 rpm
Maximum speed 2260 rpm
Engine weight 665 kg
Number of cylinders 6
Engine cubic capacity 8,4 l
Piston travel 145 mm
Piston diameter 111 m m
Compression ratio 16,7 bar ± 0,5 bar
Compression pressure 24 bar
Injection pump brand Bosch
Injection pump type CP 3.3
Firing order 1-5-3-6-2-4
Maximum pressure in the high-pressure system 1400 bar
Injector brand Bosch
Injector type CRIN 2/8 holes
Charge pump type Electric
Fuel prefilter filtration capacity 30 μ
Main fuel filter filtration capacity 5 μ
Low-pressure system pressure at minimum speed 0,75 bar
Low-pressure system pressure at maximum speed 0,75 bar
Recommended oil: CI-4 (ACEA and API)
Maximum operating tilt (precautions) Oil/fuel consumption Maximum 0.1%
Lubrication system Gear pump at the bottom of the timing
Oil cooling system Cooler integrated into the engine (left side)
Oil pressure at minimum speed 1 bar
Oil pressure at maximum speed 2,5 bar at 5 bar depending on the temperature
Relief valve adjustment pressure 5 bar (spring pressure)
Air suction type Turbocharged with air/air intercooler
Air preheating type Grid heater with relay controlled by the ECU
Number of valves 24
Valve clearance value 0,35 mm (inlet and exhaust)
Engine cooling system Water cooling
Fan type Vistronic fan
Thermostat begins to open at 83 °C
Liquid temperature from - to - 35 °C to 108 °C
Air compressor brand for the brake system Knorr
Type of compressor Piston
Pressure range: 6,5 bar to 8 bar
Block preheater 110 or 220 volts
1A10.18 Massey Ferguson 8600 - Issue
8600 series tractors - General
Engine
Fuel preheater Accessory kit available
Urea preheater Urea system and cab heating in parallel
Gas recycling system Internal EGR or SCR system
Internal EGR system Additional intake cam
SCR system (AdBlue/DEF injection) Exhaust outlet treatment system
Safety system Quality sensor in the tank
Device brand Bosch
Type of control Bosch controller
Main filter filtration capacity Secondary filter filtration capacity Tertiary filter filtration capacity Urea solidification temperature - 11 °C
Belt: air conditioning compressor/left-hand alternator/air compres-
sor (2 dimensions: with or without air compressor)
Belt: fan/right-hand alternator/air compressor (2 dimensions: a dif-
ferent fan pulley is used depending on the power)
Poly V 6 rib belt
Poly V 12 rib belt
Rear axle transmission
Gearbox type Continuous variation
Transmission type ML 260
Number of ranges 2 ranges (hare and tortoise)
Maximum speed 40 km/h or 50 km/h
Number of creeper gears No creeper gears
Rear axle type HA 260
Number of pinion/ring gear teeth 12/43
Rear axle ratio (crownwheel and pinion) 32.967
4WD ratio 0.68
Final drive type Epicyclic
Final drive reduction ratio 9.2 (123+15/15)
Maximum 4WD clutch torque 330 daNm
Number of 4WD discs 8 discs
Main brake type 10" oil-immersed disc
Number of discs 6 discs
Braking pressure 0 to 60 bar
Parking brake type ParkLock (electrical/hydraulic)
Trailer brake type Hydraulic and pneumatic
Pneumatic trailer braking pressure 6,5 bar to 8 bar
Hydraulic trailer braking pressure 0 to 150 bar
Maximum operating tilt 25° pitch (front/rear)
25° roll (right/left)
17° combined
Transmission preheater 110 volts/150 watt
Total loaded weight supported by rear axle 40 kph: 12000 kg
50 kph: 10000 kg
Front axle
Front axle brand DANA
Axle type Suspended or fixed
Massey Ferguson 8600 - Issue 1A10.19
8600 series tractors - General
Front axle
Supplier reference Fixed: 770/504
Suspended: 770/612
Rotational direction Clockwise
Front axle weight Fixed: 765 kg
Suspended: 1066 kg
Total loaded weight supported by front axle 40 kph: 9000 kg
50 kph: 7500 kg
Recommended oil type (beam and final drive) SAE 85 W 90 (API GL5)
Total ratio for front axle 16.862
Number of teeth on final drive 14 x 35 x 85
Final drive ratio 7. 0 7 1
Number of pinion/ring gear teeth 13/31
Number of differential discs 15 discs
Maximum steering angle 55°
Oscillation angle Type of oscillation stop Mechanical
Steering ram diameter 45 mm x 90 mm
Steering ram stroke 2 x 143,5 mm
Suspension type Hydraulics
Suspension ram diameter 90 mm x 100 mm
Suspension ram stroke 100 mm
Hydraulic control unit brand Husco
Hydraulic control unit nominal pressure 200 bar
Number of accumulators 2
Accumulator pressure Left 1 l : 10 bar
Right 1,4 l : 50 bar
Suspension sensor type Angular potentiometer.
Steering sensor type Angular potentiometer.
Brake type Combined with the rear brake
Factor K 1.331
Electrohydraulic
System type Load Sensing
Flow rate 175 l/min
High-pressure pump type Sauer Danfoss piston pump
High-pressure pump displacement 75 cm³
High-pressure pump rotational speed 2200 rpm
High-pressure pump maximum flow rate 200 l/min
High-pressure pump maximum pressure 200 bar
Maximum quantity of oil to add for heavy implements 16 l
Maximum exportable oil quantity (without adding oil) 64 l
Maximum exportable oil quantity (adding oil) 74 l
Charge pump type Gravity
Main relief valve adjustment pressure 200 bar ± 10 bar
Number of spool valves (maximum) 8
Number of front "push-pull" connectors 4 connectors i.e. 2 spool valves
Number of rear "push-pull" connectors 12 connectors i.e. 6 spool valves
1A10.20 Massey Ferguson 8600 - Issue
8600 series tractors - General
Electrohydraulic
Maximum flow rate per spool valve 100 l/min
Spool valve control type Electric
Recommended oil: According to MF CMS M1145 specification
Steering
Steering type Hydrostatic
Type of control Steering wheel or steering wheel + electrohydraulic spool valves
Orbitrol displacement 315 cm³
Steering ram diameter 90 mm x 45 mm
Steering ram stroke 2 x 143,5 mm
Working pressure 175 bar ± 5 bar
Pressure relief valve adjustment pressure 175 bar ± 5 bar
Shock valve adjustment pressure 240 bar
Oil recommended for steering According to MF CMS M1145 specification
Linkage
Rear lift ram diameter 105 mm
Rear linkage travel 788 mm or 860 mm
Maximum lifting capacity at ball joints (rear) 10000 kg
Operating pressure (rear) 180 bar
3-point linkage category (rear) 3 or 4
Front lift ram diameter 100 mm x 50 mm
Front linkage travel 216 mm ± 1,5 mm
Maximum lifting capacity at ball joints (front) 5000 kg
Operating pressure (front) 180 bar
3-point linkage category (front) 3
Rear power take-off (PTO)
Number of selections possible for rear PTO 540/1000 or 540E/1000
Maximum permissible power 540/540E in 1"3/8 (6 and 21 splines) 100 hp
Maximum permissible power 540/540E in 1"3/4 (20 splines) 160 hp
Maximum permissible power 1000 in 1"3/8 (6 and 21 splines) 180 hp
Maximum permissible power 1000 in 1"3/4 (20 splines) 300 hp
Engine speed if PTO 540 2037 rpm
Engine speed if PTO 540 eco 1598 rpm
Engine speed if PTO 1000 2031 rpm
Rotational direction Clockwise
Clutch type Hydraulics
Number of clutch discs 8 discs
Control pressure 18 bar
Splined shaft type 6 and 21 in 1"3/8 and 20 in 1"3/4
Front power take-off
Number of selections possible for front PTO 1000 rpm
Maximum permissible power Clockwise: 147 hp
Anti-clockwise: 221 hp
Maximum permissible torque Clockwise: 1000 Nm
Anti-clockwise: 1500 Nm
Massey Ferguson 8600 - Issue 1A10.21
8600 series tractors - General
Front power take-off
Rotational direction 2 directions of rotation
Engine speed if PTO 1000 2040 rpm
Ratio 2.04
Clutch type Hydraulics
Splined shaft type 6 and 21 in 1"3/8
Electric
Battery brand TAB
Battery specifications (2 batteries) 12 V - 105 A/H
Maximum current at start-up (IEC standard) 1010 A
Starter type 12 V noseless
Starter power 4.2 kW
Alternator type 2 x 14 V/80 A (160 A) or 2 x 14 V/120 A (240 A)
Current available on ISOBUS connector 50 A
Electronics
Function of each controller
DCC3 Instrument panel
AUTO 4 Transmission
4 AUTO 5 DC Linkage/ParkLock/Suspended front axle/Armrest/Semi-active cab
PVG 32 valves Electrohydraulic spool valves
Lights module User interface for lights
Lighting controller Lighting control
1 ECM Tier 3 SISU Engine
1 Orbitrol Danfoss valve Orbitrol for the Auto-Guide function
Data 4 Onboard computer
Automatic air conditioning module Air conditioning
DCU Denoxtronic module
Cab and fittings
Type of cab suspension available Passive
Semi-active
Type of rear-view mirror control available Manual or automatic
Type of air conditioning control available Manual or automatic
Type and brand of air conditioning compressor SANDEN with axial pistons
Compressor displacement 154.9 cm3/rev.
Refrigerant R134a
Cab noise level 71 DBA
Roof type Standard or with window
Model 8690
Engine
Brand SISU
Ty p e 84CTA
Nominal power (ISO TR14396) at 2200 rpm 340 hp
Maximum power (ISO TR14396) at 2000 rpm 370 hp
Maximum torque (ISO TR14396) 1540 Nm
Nominal PTO power (OECD) at 2200 rpm 290 hp
1A10.22 Massey Ferguson 8600 - Issue
8600 series tractors - General
Engine
Maximum PTO power (OECD) at PTO 1000 rpm 320 hp
Idle speed 800 rpm
Maximum speed 2260 rpm
Engine weight 665 kg
Number of cylinders 6
Engine cubic capacity 8,4 l
Piston travel 145 mm
Piston diameter 111 mm
Compression ratio 16,7 bar ± 0,5 bar
Compression pressure 24 bar
Injection pump brand Bosch
Injection pump type CP 3.3
Firing order 1-5-3-6-2-4
Maximum pressure in the high-pressure system 1400 bar
Injector brand Bosch
Injector type CRIN 2/8 holes
Charge pump type Electric
Fuel prefilter filtration capacity 30 μ
Main fuel filter filtration capacity 5 μ
Low-pressure system pressure at minimum speed 0,75 bar
Low-pressure system pressure at maximum speed 0,75 bar
Recommended oil: CI-4 (ACEA and API)
Maximum operating tilt (precautions) Oil/fuel consumption Maximum 0.1%
Lubrication system Gear pump at the bottom of the timing
Oil cooling system Cooler integrated into the engine (left side)
Oil pressure at minimum speed 1 bar
Oil pressure at maximum speed 2,5 bar at 5 bar depending on the temperature
Relief valve adjustment pressure 5 bar (spring pressure)
Air suction type Turbocharged with air/air intercooler
Air preheating type Grid heater with relay controlled by the ECU
Number of valves 24
Valve clearance value 0,35 mm (inlet and exhaust)
Engine cooling system Water cooling
Fan type Vistronic fan
Thermostat begins to open at 83 °C
Liquid temperature from - to - 35 °C to 108 °C
Air compressor brand for the brake system Knorr
Type of compressor Piston
Pressure range: 6,5 bar to 8 bar
Block preheater 110 or 220 volts
Fuel preheater Accessory kit available
Urea preheater Urea system and cab heating in parallel
Gas recycling system SCR system
SCR system (AdBlue/DEF injection) Exhaust outlet treatment system
Safety system Quality sensor in the tank
Device brand Bosch
Type of control Bosch controller
Massey Ferguson 8600 - Issue 1A10.23
8600 series tractors - General
Engine
Main filter filtration capacity Secondary filter filtration capacity Tertiary filter filtration capacity Urea solidification temperature - 11 °C
Belt: air conditioning compressor/left-hand alternator/air compres-
sor (2 dimensions: with or without air compressor)
Belt: fan/right-hand alternator/air compressor (2 dimensions: a dif-
ferent fan pulley is used depending on the power)
Rear axle transmission
Gearbox type Continuous variation
Transmission type ML 260
Number of ranges 2 ranges (hare and tortoise)
Maximum speed 40 km/h or 50 km/h
Number of creeper gears No creeper gears
Rear axle type HA 260
Number of pinion/ring gear teeth 12/43
Rear axle ratio (crownwheel and pinion) 32.967
4WD ratio 0.68
Final drive type Epicyclic
Final drive reduction ratio 9.2 (123+15/15)
Maximum 4WD clutch torque 330 daNm
Number of 4WD discs 8 discs
Main brake type 10" oil-immersed disc
Number of discs 6 discs
Braking pressure 0 to 60 bar
Parking brake type ParkLock (electrical/hydraulic)
Trailer brake type Hydraulic and pneumatic
Pneumatic trailer braking pressure 6,5 bar to 8 bar
Hydraulic trailer braking pressure 0 to 150 bar
Maximum operating tilt 25° pitch (front/rear)
Transmission preheater 110 volts/150 watt
Total loaded weight supported by rear axle 40 kph: 12000 kg
Poly V 6 rib belt
Poly V 12 rib belt
25° roll (right/left)
17° combined
50 kph: 10000 kg
Front axle
Front axle brand DANA
Axle type Suspended or fixed
Supplier reference Fixed: 770/504
Suspended: 770/612
Rotational direction Clockwise
Front axle weight Fixed: 765 kg
Suspended: 1066 kg
Total loaded weight supported by front axle 40 kph: 9000 kg
50 km/h : 7500 kg
Recommended oil type (beam and final drive) SAE 85 W 90 (API GL5)
Total ratio for front axle 16.862
1A10.24 Massey Ferguson 8600 - Issue
8600 series tractors - General
Front axle
Number of teeth on final drive 14 x 35 x 85
Final drive ratio 7. 0 7 1
Number of pinion/ring gear teeth 13/31
Number of differential discs 15 discs
Maximum steering angle 55°
Oscillation angle Type of oscillation stop Mechanical
Steering ram diameter 45 mm x 90 mm
Steering ram stroke 2 x 143,5 mm
Suspension type Hydraulics
Suspension ram diameter 90 mm x 100 mm
Suspension ram stroke 10 0 mm
Hydraulic control unit brand Husco
Hydraulic control unit nominal pressure 200 bar
Number of accumulators 2
Accumulator pressure Left 1 l : 10 bar
Right 1,4 l : 50 bar
Suspension sensor type Angular potentiometer.
Steering sensor type Angular potentiometer.
Brake type Combined with the rear brake
Factor K 1.331
Electrohydraulic
System type Load Sensing
Flow rate 175 l/min
High-pressure pump type Sauer Danfoss piston pump
High-pressure pump displacement 75 cm³
High-pressure pump rotational speed 2200 rpm
High-pressure pump maximum flow rate 200 l/min
High-pressure pump maximum pressure 200 bar
Maximum quantity of oil to add for heavy implements 16 l
Maximum exportable oil quantity (without adding oil) 64 l
Maximum exportable oil quantity (adding oil) 74 l
Charge pump type Gravity
Main relief valve adjustment pressure 200 bar ± 10 bar
Number of spool valves (maximum) 8
Number of front "push-pull" connectors 4 connectors i.e. 2 spool valves
Number of rear "push-pull" connectors 12 connectors i.e. 6 spool valves
Maximum flow rate per spool valve 100 l/min
Spool valve control type Electric
Recommended oil: According to MF CMS M1145 specification
Steering
Steering type Hydrostatic
Type of control Steering wheel or steering wheel + electrohydraulic spool valves
Orbitrol displacement 315 cm³
Steering ram diameter 90 mm x 45 mm
Steering ram stroke 2 x 143,5 mm
Massey Ferguson 8600 - Issue 1A10.25
8600 series tractors - General
Steering
Working pressure 175 bar ± 5 bar
Pressure relief valve adjustment pressure 175 bar ± 5 bar
Shock valve adjustment pressure 240 bar
Oil recommended for steering According to MF CMS M1145 specification
Linkage
Rear lift ram diameter 105 mm
Rear linkage travel 788 mm or 860 mm
Maximum lifting capacity at ball joints (rear) 10000 kg
Operating pressure (rear) 180 bar
3-point linkage category (rear) 3 or 4
Front lift ram diameter 100 mm x 50 mm
Front linkage travel 216 mm ± 1,5 mm
Maximum lifting capacity at ball joints (front) 5000 kg
Operating pressure (front) 180 bar
3-point linkage category (front) 3
Rear power take-off (PTO)
Number of selections possible for rear PTO 540/1000 or 540E/1000
Maximum permissible power 540/540E in 1"3/8 (6 and 21 splines) 100 hp
Maximum permissible power 540/540E in 1"3/4 (20 splines) 160 hp
Maximum permissible power 1000 in 1"3/8 (6 and 21 splines) 180 hp
Maximum permissible power 1000 in 1"3/4 (20 splines) 300 hp
Engine speed if PTO 540 2037 rpm
Engine speed if PTO 540 eco 1598 rpm
Engine speed if PTO 1000 2031 rpm
Rotational direction Clockwise
Clutch type Hydraulics
Number of clutch discs 8 discs
Control pressure 18 bar
Splined shaft type 6 and 21 in 1"3/8 and 20 in 1"3/4
Front power take-off
Number of selections possible for front PTO 1000 rpm
Maximum permissible power Clockwise: 147 hp
Anti-clockwise: 221 hp
Maximum permissible torque Clockwise: 1000 Nm
Anti-clockwise: 1500 Nm
Rotational direction 2 directions of rotation
Engine speed if PTO 1000 2040 rpm
Ratio 2.04
Clutch type Hydraulics
Splined shaft type 6 and 21 in 1"3/8
Electric
Battery brand TAB
Battery specifications (2 batteries) 12 V - 105 A/H
Maximum current at start-up (IEC standard) 1010 A
1A10.26 Massey Ferguson 8600 - Issue
8600 series tractors - General
Electric
Starter type 12 V noseless
Starter power 4.2 kW
Alternator type 2 x 14 V/80 A (160 A) or 2 x 14 V/120 A (240 A)
Current available on ISOBUS connector 50 A
Electronics
Function of each controller
DCC3 Instrument panel
AUTO 4 Transmission
4 AUTO 5 DC Linkage/ParkLock/Suspended front axle/Armrest/Semi-active cab
PVG 32 valves Electrohydraulic spool valves
Lights module User interface for lights
Lighting controller Lighting control
1 ECM Tier 3 SISU Engine
1 Orbitrol Danfoss valve Orbitrol for the Auto-Guide function
Data 4 Onboard computer
Automatic air conditioning module Air conditioning
DCU Denoxtronic module
Cab and fittings
Type of cab suspension available Passive
Semi-active
Type of rear-view mirror control available Manual or automatic
Type of air conditioning control available Manual or automatic
Type and brand of air conditioning compressor SANDEN with axial pistons
Compressor displacement 154.9 cm3/rev.
Refrigerant R134a
Cab noise level 71 DBA
Roof type Standard or with window
Massey Ferguson 8600 - Issue 1A10.27
8600 series tractors - General
38 km/h
(23,61 mph)
16 km/h
(9,94 mph)
50 km/h
(31,07 mph)
40 km/h
(24,86 mph)
28 km/h
(17,40 mph)
0,03 km/h
(0,02 mph)
C.
Forward speeds
C.1 Forward speed for all models wit h transmission in modeDyna-VT
Tractor version 50 kph*
*depending on country legislation.
For the 40 km/h version, the speed is electronically controlled.
For the 40 km/h version, the tractor reaches maximum speed at 1600 rpm.
For the 50 km/h version, the tractor reaches maximum speed at 1900 rpm.
Continuous variation mode
Forward Reverse
Slow speed range (Tortoise) 0,03 km/h to 28 km/h 0,03 km/h to 16 km/h
High speed range (Hare) 0.03 kph to 40 kph or 50 kph depending
on version
0,03 km/h to 38 km/h
I006017
C.2 Forward speed for all models wit h transmission in Stepshift mode
High speed range (Hare) Slow speed range (Tortoise) Creeper range (Snail)
Forward
travel
1 F 1.7 kph 4.0 kph 4.6 kph 0.8 kph 1.8 kph 2.1 kph 0.1 kph 0.2 kph 0.2 kph
2 F 1.9 kph 4.4 kph 5.1 kph 0.9 kph 2.2 kph 2.5 kph 0.2 kph 0.4 kph 0.5 kph
3 F 2.1 kph 5.0 kph 5.8 kph 1.1 kph 2.6 kph 3.0 kph 0.3 kph 0.6 kph 0.7 kph
4 F 2.4 kph 5.6 kph 6.5 kph 1.3 kph 3.0 kph 3.5 kph 0.3 kph 0.8 kph 0.9 kph
5 F 2.7 kph 6.4 kph 7.4 kph 1.4 kph 3.4 kph 3.9 kph 0.4 kph 1.0 kph 1.2 kph
6 F 3.0 kph 7.2 kph 8.3 kph 1.6 kph 3.8 kph 4.4 kph 0.5 kph 1.2 kph 1.4 kph
7 F 3.5 kph 8.2 kph 9.5 kph 1.8 kph 4.2 kph 4.9 kph 0.6 kph 1.4 kph 1.6 kph
8 F 4.0 kph 9.4 kph 10.9 kph 2.0 kph 4.8 kph 5.6 kph 0.7 kph 1.6 kph 1.9 kph
9 F 4.5 kph 10.8 kph 12.5 kph 2.3 kph 5.4 kph 6.3 kph 0.8 kph 1.8 kph 2.1 kph
10 F 5.2 kph 12.4 kph 14.4 kph 2.6 kph 6.2 kph 7.2 kph 0.8 kph 2.0 kph 2.3 kph
11 F 6.0 kph 14.2 kph 16.4 kph 2.9 kph 7.0 kph 8.1 kph 0.9 kph 2.2 kph 2.5 kph
12 F 6.8 kph 16.2 kph 18.8 kph 3.4 kph 8.0 kph 9.3 kph 1.0 kph 2.4 kph 2.8 kph
13 F 7.7 kph 18.4 kph 21.3 kph 3.9 kph 9.2 kph 10.7 kph 1.2 kph 2.8 kph 3.2 kph
800 rpm 190 0
rpm
2200
rpm
800 rpm 1900
rpm
2200
rpm
800 rpm 190 0
rpm
Fig. 1
2200
rpm
1A10.28 Massey Ferguson 8600 - Issue
Loading...