Fender Mustang v.2, Mustang III v.2, Mustang IV v.2, Mustang V v.2, Mustang I v.2 Advanced Owner's Manual

™

MUSTANG

GUITAR AMPLIFIERS

(

v.2

)

BY

FENDER

®

ADVANCED OWNER'S MANUAL

MUSTANG™ III/IV/V (v.2)

Advanced Manual

not active and the knob positions will NOT show their actual
settings when a preset is first selected.

Introduction

This manual is your step-by-step guide to the advanced
features found on your Mustang™ (v.2) amplifier. Turn
to page 10 for the Mustang I / II advanced manual. For
information on using Fender® FUSE™, Ableton® Live
or Amplitube®, please see the separate manuals for each
product available at www.fender.com/support.

Navigation

There are just a few basics of Mustang navigation that you
should know before you explore any further...

Selecting Presets

Turn the DATA WHEEL to select one of 100 presets.

Preset contents are displayed

on screen for each preset

DATA

WHEEL

MASTER volume is

always

active

     

PROGRAMMABLE knobs are inactive unless turned

How do I activate a programmable knob? The moment you
turn any programmable knob it instantly becomes active and
it will remain active until you select a different preset, at which
time all the programmable knobs become inactive again.





Turn a PROGRAMMABLE knob to activate it

Press the DATA WHEEL to see what the stored preset settings
are for all the programmable knobs before you turn them.
Press EXIT to return to Play mode.

  

You will find some presets you like and others that you want
to change...

Each preset stores the settings for:

• Amplifier type — 17 selections

• Effects — 4 categories, 44 selections total

• Knob levels — GAIN through REVERB (not MASTER)

You can also select and edit presets from your computer

♫

using Fender® FUSE™ software, available free of charge
at www.fender.com/support

Master Volume

The MASTER volume knob is always "active." That means the
position of the MASTER knob always shows the true master
volume setting, unlike the programmable knobs.

(Always turn the MASTER volume knob first to adjust the
overall volume output of your Mustang amplifier.)

Programmable Knobs

Because the setting of every knob (except MASTER) is stored
within each preset, the "programmable" knob postitions are

To view preset knob settings, push the DATA WHEEL

Press the DATA WHEEL a second time to see where your
effects are located in the Guitar Signal Processing Path.
Press EXIT to return to Play mode.

x2

To view the Signal Path, push the DATA WHEEL twice.

You can change the order of effects in the Signal Path

♫

using Fender® FUSE™ software.

2

fender.com

MUSTANG™ III/IV/V (v.2)

Amplifier Menus

Select amplifier models and adjust amplifier settings using
the Amp menus.

You can de-select the highlighted amp setting and

♫

return to Amp Model selection mode, as a shortcut, by
pressing and holding the AMP button.

4. Press EXIT to return to Play mode.

Amplifier Models

To select Amplifier Models:

1. Press the AMP button.

2. Turn the DATA WHEEL to select one of 17 amplifier models:

AMP MODELS

Studio Preamp
'57 Champ
'57 Deluxe
'57 Twin
'59 Bassman
'65 Princeton
'65 Deluxe Reverb
'65 Twin Reverb
'60s Thrift
British Watts
British '60s
British '70s
British '80s
British Colour
Super-Sonic (Burn)
American '90s
Metal 2000

3. Press EXIT to return to Play mode.

Effect Menus

Bypassing Effects

You can turn on–off effects that have been selected for the
current preset by pressing the corresponding effect button.

The Effect name is highlighted
and the Effect button lights up

when an effect is active

Effects can also be bypassed (turned on-off) from the

♫

footswitch included with your Mustang amplifier.

Effects that are shown on screen as "–EM PT Y–" can not be
activated until an effect has been selected in that slot.

Amplifier Settings

To adjust Amplifier Settings:

1. Press the AMP button.

2. Press the DATA WHEEL one or more times until the setting

that you want to adjust is highlighted, then turn the DATA
WHEEL to adjust the setting.

3. Press the AMP button a second time to access "Page 2" with

more amplifier settings. The settings that appear on "Page2"
will depend on the amp model that is currently selected.

"PAGE 2" of the Amp menus

Press the DATA WHEEL repeatedly

to select the next Amp setting

Selecting Effects

• — Stompbox effects

• — Modulation effects

• — Delay effects

• — Reverb effects

To select Effects:

1. Press and hold one of the four effects buttons.

2. Turn the DATA WHEEL to select one of the following

effects:

STOMPBOX MODULATION

Ranger Boost Sine Chorus
Green Box Triangle Chorus
Overdrive Sine Flanger
Fuzz Triangle Flanger
Orange Box Vibratone
Black Box Vintage Tremolo
Big Fuz z Sine Tremolo
Wah Ring Modulator
Touch Wah Step Filter
Simple Compressor Phaser
Compressor Wah

Touch Wah
Diatonic Pitch
Pitch Shifter

fender.com

3

MUSTANG™ III/IV/V (v.2)

Effects tables continued from previous page...

DE LAY REVERB

Mono Delay Small Hall
Mono Echo Filter Large Hall
Stereo Echo Filter Small Room
Multitap Delay Large Room
Ping Pong Delay Small Plate
Ducking Delay Large Plate
Reverse Delay Ambient
Tape Delay Arena
Stereo Tape Delay Fender '63 Spring

3. Press EXIT to return to Play mode.

You can switch to a different effect category at any time,

even while you are in the effect selection menus, by

♫

pressing and holding a different Effects button.

Fender '65 Spring

Effect Settings

Use the Effects Settings menus to adjust a dazzling array of
effect settings.

To adjust Effect Settings:

1. Press and hold any Effect button (STOMP, MOD, DELAY,

REVERB).

2. Turn the DATA WHEEL to select the effect you want to

work with.

3. Press the DATA WHEEL one or more times until the setting

that you want to adjust is highlighted, then turn the DATA
WHEEL to adjust the setting.

Tap Button

The TAP button can be used to "tap in" delay time and
modulation rate settings, by rhythmically pressing the TAP
button.

When you select a delay effect, the TAP button will blink
in time with the delay time setting. When you select a
modulation effect, the TAP button will blink in time with
the modulation rate setting (note that modulation rates can
have up to 12 second intervals and the TAP button will flash
infrequently).

When both delay and modulation effects are selected
simultaneously, the TAP button will blink in time with the
delay effect and will only control the delay time setting.

You can use the Effects menus or Fender FUSE to set

♫

delay time and modulation rates more precisely.

To set the TAP interval of effects:

1. Select a Delay or Modulation effect that causes the TAP

button to blink, using the Effects menus (see Selecting
Effects, page 3).

2. Press the TAP button rhythmically (twice minimum) in time

with the desired interval. If you press the TAP button only
once, the interval will be set to the maximum value.

If you open the Effect settings menu (see Effect Settings,

♫

above), you can watch the actual TAP values you are
setting while you are tapping them in!

Press the DATA WHEEL repeatedly

to select the next Effect setting

4. Press EXIT to return to Play mode.

You can bypass an effect at any time, even while you

♫

are in the effect settings menus, by pressing the Effect
button or corresponding footswitch button.

Saving Presets

Your Mustang™ amplifier gives you the powerful ability to
save every setting on the amplifier as part of a preset. When
you select a preset, the level of each knob, every effect
setting, and the amp model selection, are instantly recalled to
your pre-programmed settings.

The SAVE button will light up red when you turn



any programmable knob or edit any other setting
on the amp. This indicates that you have temporarily modified
the preset. You can undo your modifications by turning the
DATA WHEEL to a different preset and then back again.

The EXIT button will not cancel changes to the current

♫

preset. Only by selecting a different preset using the
DATA WHEEL, Footswitch, or Fender FUSE, will your
temporary changes be erased.

To save a preset:

Memory Lock must be OFF to save presets (see Utility

♫

Menus, page 7)

4

fender.com

MUSTANG™ III/IV/V (v.2)

1. To save a preset you should first modify an existing preset,

for example, by turning any of the programmable knobs,
such as GAIN.

2. Press the SAVE button. The SAVE and EXIT buttons should

be illuminated. You can press EXIT at this point to cancel
the save process.

3. Turn the DATA WHEEL select a preset destination to

overwrite.

4. Press the DATA WHEEL if you want to edit the name of

your new preset. Use the buttons to perform the functions
listed along the bottom of the screen; turn the DATA
WHEEL to select characters.

5. Press the SAVE button a second time to confirm the save.

5. Press EXIT or TAP to exit from the Tuner.

Footswitches

Four-Button Footswitch (0080996000)

Connect a 4-button footswitch to your Mustang amplifier
(included with the Mustang IV & V, optional equipment for the
Mustang III) to enable remote multi-function foot control. The
footswitch display and LEDs show some of the same informa­tion as the amplifier screen, so you can, for example, tune
your guitar and select presets by watching the footswitch
without ever looking at the screen onboard the Mustang!

• Select Quick Access presets (QA1/QA2/QA3)

• Select presets (up/down/bank)

• Bypass effects

• Activate the Tuner

Mode indicators

Guitar Tuner

Your Mustang™ amplifier has a built-in Tuner mode that turns
the screen into a guitar tuner.

To use the Tuner:

1. Press and hold the TAP button. The TAP and EXIT buttons

will illuminate.

2. Strike any single string on your guitar and watch the

screen. The note of the string being tuned is displayed
along with a fine tuning needle.

"In tune"

3. Turn the tuning peg on your guitar until the fine tuning

needle indicates the string is in tune, as shown above.

4. Standard guitar tuning is as follows:

The footswitch has three modes that are identified by the
three LEDs labeled MODE 1, MODE 2 and MODE 3. The
footswitch also has a Tuner mode which is indicated when all
of the mode LEDs are off.

To switch between modes, press the MODE button. To acti­vate Tuner mode, press and hold the MODE button.

You can lock the 4-button footswitch in Mode 1, 2 or3

♫

using the Utility menus, to prevent accidental Mode
changes (see Utility Menus, page 7).

• Mode 1—In Mode 1 the footswitch is used to select one of
three Quick Access presets, using the buttons labeled: QA1 /
QA2 / QA3 (in line with the MODE 1 LED). When you select a
Quick Access preset, the number of the preset will appear in
the display of the footswitch.

You can any assign any preset to be a Quick Access

♫

preset in the Utility menus. (see Utility Menus, page 7).

• Mode 2—In Mode 2 the footswitch is used to select presets
down/up, or in banks of 10, using the buttons labeled: DOWN
/ UP / BANK (in line with the MODE2 LED). When you select a
preset, the number of the preset will appear in the display of
the footswitch.

fender.com

5

MUSTANG™ III/IV/V (v.2)

• Mode 3—In Mode 3 the footswitch is used to bypass the
Stompbox, Modulation or Delay effects, using the buttons
labeled: STOMP / MOD / DELAY (in line with the MODE 3
LED). The footswitch button LEDs indicate the effects that are
active, just like the buttons on the amplifier.

You can also have a footswitch button assigned to

bypass the Reverb effect by adding on the 2-button

♫

Mustang footswitch (see Six-Button Footswitching
options, below).

• Tuner Mode—Press and hold the MODE button to activate
the Tuner. The ampifier screen and the footswitch both will
display the same tuner information so that you can look in
either place to tune your guitar. The footswitch will display
the nearest note; the button LEDs will indicate sharp and
flat and "in tune" is indicated when the green LED below the
footswitch display lights up.

Press any footswitch button to exit Tuner mode.

Two-Button Footswitch (0080997000)

Connect a 2-button footswitch to your Mustang amplifier
(included with the Mustang III, optional equipment for the
Mustang IV & V) to enable remote multi-function foot control.
Use the Utility menus (see page 7) to assign one of the follow­ing functions to the 2-button footswitch:

• Select presets (up/down)

• Select Quick Access presets (QA1/QA2)

• Bypass effects (various combinations)

• Set TAP interval

EXP-1 Expression Pedal

The EXP-1 expression pedal (P/N 2301050000) is a dual-mode
pedal that can be programmed to control a wide variety of
parameters on your Mustang amplifier. Plug the EXP-1 pedal
into the "4 BUTTON FOOTSWITCH" jack .

The EXP-1 operates in two modes, Volume behavior mode
and Expression behavior mode. Switch between modes by
pressing down hard on the toe end of the pedal. Red and
green LEDs on the EXP-1 indicate the current pedal mode:

• Volume behavior mode (green) is used to control master

volume (or the EXP-1 can be set to OFF in Volume mode).

• Expression behavior mode (red) can be used to control

most effect and amp parameters on your Mustang amplifier.
Some common uses are to control the frequency parameter
of a wah effect or the rate/time parameter of a modulation
or delay effect.

Fender® FUSE™ software can also be used to program

♫

all settings on your EXP-1 pedal.

Six-Button Footswitching options

Plug both a 4-button and a 2-button footswitch into your
Mustang amplifier to expand your remote control options.
By assigning different functions to each footswitch you can
create more than a dozen different foot control combinations.

For example, you could assign Quick Access presets to the
4-button footswitch and Up/Down presets to the 2-button
footswitch. Or you could bypass effects with the 4-button
footswitch and select presets with the 2-button footswitch.
The choice is up to you.

6

EXP-1 Pedal Calibration

The first time you connect the EXP-1 to your Mustang ampli­fier, you should calibrate it so that the desired range of pedal
movement registers with the amplifier. Calibration takes less
than a minute:

To calibrate the EXP-1:

1. Plug the EXP-1 pedal into the 4 BUTTON FOOTSWITCH

jack on the back of your Mustang amplifier using the
included cable.

2. Turn the amplifier OFF.

3. Press and hold the UTIL button on the amplifier, then

turn the amplifier ON. Continue holding the UTIL button
down until it is no longer illuminated.

4. Move the EXP-1 pedal between the desired heel and toe

endpoints to set the range of pedal movement that is
registered (recognized) by the amplifier.

fender.com

MUSTANG™ III/IV/V (v.2)

For example, if you only want the middle third of the

♫

pedal range to register with the amplifier, only move
the EXP-1 pedal back and forth through the middle
third of its range of motion. You must start the calibra­tion process with the EXP-1 pedal positioned some­where within the desired range.

5. Turn the DATA WHEEL to select a new preset.

6. The EXP-1 expression pedal has been calibrated!

Repeat the calibration procedure each time you

♫

change EXP-1 pedals, plug the EXP-1 into a different
amplifier, or perform a Factory Restore proceedure
(see page 9) on the amplifier.

EXP-1 Pedal Settings

The EXP-1 pedals settings can be saved with the current pre­set so that each time you select a particular preset, the EXP-1
functions are customized for that preset. Before you change
the EXP-1 settings, select the preset that you want to save
the EXP-1 settings with.

To configure EXP-1 settings:

1. Plug the EXP-1 pedal into the 4 BUTTON FOOTSWITCH

jack on the back of your Mustang amplifier using the
included cable.

2. Select the preset with which you want to use the EXP-1.

3. Press and hold the DATA WHEEL until the Expression

Mode Enable menu appears.

4. Rotate the DATA WHEEL to change the settings in the

current menu. Press the DATA WHEEL to select the next
menu from the list below.

SHORTCUT: You can speed select menus in either direc-

♫

tion by rotating the DATA WHEEL while holding it down.

5. Save the current preset if you want to keep the modified

EXP-1 settings, otherwise, press EXIT, then select a differ­ent preset using the DATA WHEEL to erase your changes.

Expression mode. Your options will vary depending on the
category you selected in the Expression Mode Enable menu
above, and the effect module that is selected in the current
preset.

• Expression Mode Heel/Toe — (Variable) Use these two
menus to set the level of the active parameter (selected
in the menu above) with the heel of the pedal in the fully
down position (Heel Setting) and with the toe of the pedal
in the fully down position (Toe Setting). Range options will
vary depending on your selection in the Expression Mode
Parameter menu above.

• Expression Mode Type — (Capture, Live) If "Live" is
selected, the current pedal position will override the stored
preset setting for the assigned expression pedal parameter
when a preset is first selected. If "Capture" is selected, the
pedal is disabled until you move the pedal after a preset is
first selected.

• Expression Effect Bypass — (On/Off) Select "On"
to bypass (turn off) the effect currently selected in the
Expression Mode Enable menu when switching the EXP-1 to
Volume mode. Select "Off" to leave the effect active (keep
on).

• Expression Parameter Restore — (On/Off) Select "On"
to return the Expression Mode Parameter to the stored pre­set value when switching the EXP-1 to Volume mode. Select
"Off" if you want the parameter to be left set to the position
of the pedal (toe position) when switching to Volume mode.

• Volume Mode Behavior — (Volume/Off) Select "Volume"
if you want the pedal to control the master volume in
Volume mode. Select "Off" if you want the pedal to be OFF
when switched to Volume mode.

• Volume Mode Heel/Toe — (0–100%) Use these two
menus to set the master volume level with the heel of the
pedal in the fully down position (Heel Volume) and with the
toe of the pedal in the fully down position (Toe Volume).

EXP-1 Menus:

• Expression Mode Enable — (Off, Amp, Stomp, Mod,

Delay, Reverb, Volume) Select the category that you want to
control with the EXP-1 in Expression mode, or select "Off" if
you want the pedal to be OFF in Expression mode.

You must have an effect selected for the current preset

♫

on the amplifier (or in Fender FUSE) to make that cat­egory of effect become available for selection in this
menu.

• Expression Mode Parameter — (Variable) Select the
parameter that you want to control with the EXP-1 in

• Pedal Initial Source — (From Preset/From Pedal) Select
"From Preset" if you want the EXP-1 mode to switch to the
Preset Default mode (see note below) each time you select a
preset. Select "From Pedal" if you want the EXP-1 to remain
in whichever mode the EXP-1 is currently in as you change
presets. The Pedal Initial Source setting is a global setting.
It is not associated with any preset and does not need to be
saved; it stays set to the current selection.

Preset Default mode is the mode (volume or expression)

♫

that the EXP-1 is in when you save the preset. You can
change the Preset Default mode by re-saving the preset
with the EXP-1 in a different mode, or using Fender
FUSE software.

fender.com

7

MUSTANG™ III/IV/V (v.2)

Utility Menus

Press the UTIL button to activate the Utility menus.
Press the UTIL button repeatedly to step through



each of the nine menus, listed below.

• Quick Access #1 / #2 / #3 — Use the first three Utility menus
to choose Quick Access presets. You can then access those
presets quickly from the footswitches (see Footswitches,
page5).

• Two-Button Footswitch Mode — Use this menu to assign
functions to the two-button footswitch.

• Four-Button Footswitch Mode — Use this menu to lock
the four-button footswitch in Mode 1, Mode 2 or Mode 3.
Select "Normal" for normal, multi-mode operation. Tuner
mode is always available, even when a mode is locked.

• Memory Lock — Use the Memory Lock menu to prevent
accidental preset modifications. You will still be able to make
temporary changes to presets with Memory Lock ON, but you
won't be able to save those changes until Memory Lock is
switched OFF.

• Line Out Boost — Use the Line Out Boost menu to adjust
the output level of the Line Out jacks to accommodate the
input sensitivity of connected sound equipment.

Line Outputs

These stereo XLR output jacks provide balanced, line-level
signals for connection to mixing consoles or recording
equipment. Press the GROUND LIFT switch "in" to disconnect
the ground connections (pins-1) from the XLR jacks which
may reduce line noise in some situations. Normally leave this
switch in the "out" (grounded) position.

Aux / Phones Jacks

Auxiliary Input

You can use the Auxiliary jack to input audio into your



Mustang amplifier for accompaniment. Connect the
headphone output on your CD player or MP3 player to the
AUX jack using a mini-stereo cable. Use the volume control
on your player, together with the MASTER volume knob, to
adjust the auxiliary volume level.

• LCD Contrast — Use this menu to adjust the contrast of the
Mustang display.

• About This Amp — This menu displays the Firmware ver­sion currently running on the amplifier. Use this information
to determine if an update is available for your amplifier.

Speaker Outputs

Mustang V, only

The Mustang V head amplifier provides stereo speaker
outputs that must both be connected to a stereo speaker
cabinet such as the Mustang V 412, with four 12" Celestion®
G12P Rocket 50 speakers (recommended), or two 8Ω speaker
cabinets capable of handling 75W each.

Phones Jack

Plug in your headphones, ear buds, or powered



speakers to enjoy the Mustang's stereo features. This
jack may also be used as a stereo recording output. The amp's
speaker is muted when the PHONES jack is used.

Effects Loop

Connect external effects devices to your Mustang amplifier
using the effects loop jacks.

Mustang IIIMustang IV & V

The Mustang IV & V amplifiers can accept stereo or mono
effects devices. Note that a mono-in, mono-out effect unit
will use one send and one return, and only effect one side
of the stereo image. The Mustang III amplifier only accepts
mono effects devices.

Connect the FX SEND jack(s) to the input(s) on your external
effects device and connect the FX RETURN jack(s) to the
output(s) on your effects device.

8

fender.com

MUSTANG™ III/IV/V (v.2)

USB Port

Use the USB port to connect the Mustang™ amplifier to
your computer and take your music to the next level:



• Use Fender® FUSE™ software to control your Mustang
from your computer and access bonus amp features not
available from the Mustang alone.

Please see the Fender FUSE manual at www.fender.

♫

com/support for details.

• Record and edit Mustang audio using Ableton® Live Lite 8
Fender® Edition software.

Please see the Ableton® Live Lite 8 Fender edition at

♫

www.fender.com/support for details.

Factory Restore &

Firmware Update

FAQ

There are several great places you can go to learn more about
your Mustang and music in general:

• www.fender.com/support

• Join a Fender Community forum where you can ask
questions and read threads. There's even a forum just for
the Mustang: www.fender.com/community/forums

• Find music theory learning materials and sheet music at
Hal Leonard Publications: www.halleonard.com

Factory Restore

You can restore your Mustang amplifier to the original factory
settings if desired. All user presets will be erased!

To restore the Mustang amplifier to factory settings:

1. Turn the amplifier OFF.

2. Press and hold the EXIT button while turning the amplifier

ON. Continue holding the EXIT button until it is no longer
illuminated.

The FACTORY RESTORE function will erase all user

!

modified presets. It will also restore any effect selections
that have been modified using Fender FUSE software.

Firmware Update

From time to time, Fender may make available firmware
updates for your Mustang amplifier to improve operation
or to add new features. To update the firmware on your
amplifier you will need to connect it through the USB port
to a computer with Fender FUSE software and an internet
connection.

Please see the Fender FUSE manual at www.fender.

♫

com/support for details.

fender.com

9

MUSTANG™ I/II (v.2)

Advanced Manual

Introduction

This manual is your step-by-step guide to all the advanced
features found on your Mustang™ I / II amplifier. For
information on using Fender® FUSE™, Ableton® Live or
Amplitube®, please see the separate manuals for each product
available at www.fender.com/support.

Programmable Knobs

Because the setting of every knob on the Mustang amplifier
(except MASTER) is part of each preset, all programmable
knobs are normally inactive and knob positions will NOT
show their actual settings when a preset is first selected.

     

Navigation

There are just a few basics of Mustang navigation that you
should know before you explore any further...

Selecting Presets

The most powerful feature of your Mustang amplifier is its
ability to store every amplifier setting and effect selection as a
preset that you can instantly recall using the PRESET knob, or
remotely from your computer or footswitch.

Use the PRESET knob to select one of 24 presets. Presets are
stored in three banks, colored AMBER, GREEN and RED.

Turn the PRESET knob to scroll through each bank of presets
in the following order:

Programmable knob positions are inactive unless turned

How do I activate a programmable knob? The moment you
turn any programmable knob it instantly becomes active
and it will remain active until you select a different preset, at
which time it becomes inactive again.

    

Rotate knobs to activate their positions

You may hear a big change in volume or tone when you
first turn a programmable knob if there happened to be a
large difference between the knob's starting position and
the stored preset setting. For example, if the VOLUME knob
is pointing to "8" but the stored preset VOLUME setting is
"2," the volume level will jump from "2" to "8" when you start
turning the VOLUME knob because the VOLUME knob is now
instantly active at "8."

AMBER Bank

( Factor y pre se ts )

Each preset is based on one of the eight amplifier types
labeled next to each of the preset LEDs. That gives you a total
of three presets for each amplifier type.

The

♫

own presets. The
modified using Fender FUSE software available free at

www.fender.com/support

Each preset includes the settings of all the programmable
knobs on the Mustang, which includes every knob except the
MASTER volume and PRESET knobs.

10

RED

GREEN Bank

( User pres et s )

and

GREEN

RED Bank

( User pres et s )

banks are for creating your

AMBER

bank of presets can only be

.

The only way to know what the preset setting of a knob

♫

There are two effect selection knobs on the Mustang:

• MOD — selects Modulation type effects

• DLY / REV — selects Delay and Reverb type effects

You can also select effects from a STOMPBOX category

♫

The MOD and DLY / REV knobs share the same three selection
indicator LEDs. The knob turned last has control of these LEDs:

fender.com

is before you turn it, is by using Fender FUSE software
and connecting the Mustang to your computer.

Effects

using Fender FUSE software.

MOD

DLY/REV

DD

MUSTANG™ I/II (v.2)

These LEDs are linked to whichever

knob has been the last turned.

C1 Fender '65 Spring Reverb

C2 Fender '63 Spring Reverb

C3 Tape Delay Room

D1 Tape Delay Large Hall

D2 Ducking Delay Small Hall

D3 Echo Filter

MO

These LEDs are numbered 1, 2, 3 and correspond to the three
positions within each of the selection ranges A, B, C, D on
each knob. Use the LEDs to determine exactly which position
the knob is pointing to, for example, A 1 is shown below:

LY/REV

MOD

DLY/REV

Effect Selections

The tables below list the effect selections for each knob.

MODULATION EFFECTS

A1 Chorus

A2 Chorus Deep

A3 Flanger

B1 Touch Wah

B2 Bias/Sine Tremolo

B3 Optical/Vintage Tremolo Fast

C1 Vibratone Slow

C2 Vibratone Fast

C3 Pitch Shifter – Up a 5th

D1 Pitch Shifter – Down an Octave

D2 Phaser Medium

D3 Step Filter

DELAY EFFECTS REVERB EFFECTS

A1 Tape Delay 150ms / 1 Repeat

A2

Stereo Tape Delay 300ms / 3 Repeats

A3

Mono Delay 700ms / 4 Repeats

B1 Small Room Reverb

B2 Plate Reverb

B3 Large Hall Reverb

You can completely change the effects list on your

Mustang™ amplifier using Fender® FUSE™ software

♫

available at www.fender.com/support.

Effects Level

You can adjust the effects level by holding down the EXIT
button while rotating either the MOD or DLY/REV knob,
depending on which effect type you want to adjust.

Tap Button

The TAP button can be used to "tap in" delay time and
modulation rate settings:

• Delay time — TAP button blinks green:

• Modulation rate — TAP button blinks red:

When you select a delay effect, the TAP button will blink

green in time with the delay time setting. When you select a

modulation effect, the TAP button will blink red in time with
the modulation rate setting.

When both delay and modulation effects are selected
simultaneously, the TAP button will blink green and only
control the delay time setting.

You can use TAP to set both delay time and modulation

♫

rate by tapping in the modulation rate first, with NO
delay effect selected, then adding a delay effect and
tapping in the delay time last.

To set the TAP interval of effects:

1. Select an effect that causes the TAP button to blink, using

the DLY/REV or MOD knob.

2. Press the TAP button rhythmically (twice minimum) in time

with the desired interval.

fender.com

11

MUSTANG™ I/II (v.2)

Tuner Button

modifications simply by selecting a different preset and then
back again.

Your Mustang™ amplifier has a built-in Tuner mode that turns
the control panel LEDs into a chromatic guitar tuner.

To use the tuner:

1. Press and hold the TAP button for 2 seconds. The TAP and

EXIT buttons will illuminate.

2. Strike any single string on your guitar and watch the panel

LEDs. The Preset LEDs are used to indicate the note of the
string being tuned (the top LED "#" indicates if the note is
sharp).

3 LEDs indicate fine tuning. GREEN means "in tune"

Letters next to LEDs indicate the note being tuned

3. Turn the tuning peg on your guitar until the fine tuning

LEDs above the MOD knob indicate the string is in tune, as
shown above.

4. Standard guitar tuning is as follows:

The EXIT button will not cancel changes to the current

♫

preset. Only by selecting a different preset using the
PRESET knob will your temporary changes be erased.

To save a preset:

1. To save a preset you must first modify an existing preset

by turning any of the programmable knobs, such as GAIN
or MOD. (once the SAVE button is illuminated, you can
proceed to step 2).

2. Press the SAVE button. The SAVE and EXIT buttons should

be flashing rapidly. You can press EXIT at this point to
cancel the save process.

3. Turn the PRESET knob to select a preset to overwrite.

You can only overwrite the red and green banks of the
amplifier type that you started from (if you started by
modifying the amber bank, you must select either the red
or green bank to overwrite).

You can modify the AMBER bank of presets by using

♫

your computer and Fender® FUSE™ software available
at www.fender.com/support.

4. Press the SAVE button again to confirm the save.

Aux / Phones Jacks

5. Press EXIT or TAP to exit from the Tuner.

Save Button

Your Mustang amplifier gives you the powerful



ability to save every setting on the amplifier as
part of a preset. When you select a preset, the level of each
knob, including effect selections, is instantly recalled to your
pre-programmed settings!

The SAVE button will light up red when you turn any
programmable knob on the amplifier. This indicates that you
have temporarily modified the preset. You can reset your

Auxiliary Input

You can use the Auxiliary jack to input audio into your
Mustang amplifier for accompaniment. Connect the
headphone output on your CD player or MP3 player to the
AUX jack using a mini-stereo cable. Use the volume control
on your player, together with the MASTER volume knob, to
adjust the auxiliary volume level.

Phones Jack

Plug in your headphones, ear buds, or powered speakers to
enjoy the Mustang's stereo features. This jack may also be
used as a stereo recording output. The amp's internal speaker
is muted when the PHONES jack is used.

12

fender.com

MUSTANG™ I/II (v.2)

Footswitch

Connect a (optional) 1-button footswitch (P/N 0994049000)
into the FTSW jack to enable remote selection of your two
favorite presets. The LED (next to the FTSW jack) will turn red
or green to indicate which footswitch preset is active.

To program the footswitch:

1. Select a preset that you want to assign to the footswitch.

The preset must not be modified (the SAVE button must
NOT be illuminated to proceed to step 2).

2. Press the SAVE button. The SAVE and EXIT buttons should

be flashing rapidly. You can press EXIT at this point to
cancel the footswitch assignment process.

3. Press the footswitch button to select either the red or

green LED next to the FTSW jack to associate with the

chosen preset.

4. Press the SAVE button to confirm the footswitch

assignment. Now when you press the footswitch, the
chosen preset will be activated with the assigned red or

green footswitch indicator.

USB Port

Use the USB port to connect the Mustang™ amplifier to your
computer and take your music to the next level:

• Use Fender® FUSE™ software to control your Mustang
from your computer and access bonus amp features not
available from the Mustang alone.

Factory Restore &

Firmware Update

Factory Restore

You can restore your Mustang amplifier to the original factory
settings if desired. All user presets will be erased!

To restore the Mustang amplifier to factory settings:

1. Turn the amplifier OFF.

2. Press and hold the EXIT button while turning the amplifier

ON. Continue holding the EXIT button until it is no longer
illuminated.

The FACTORY RESTORE function will erase all user

!

modified presets. It will also restore the AMBER bank
of presets and any effect selections that have been
modified using Fender FUSE software.

Firmware Update

From time to time, Fender may make available firmware
updates for your Mustang amplifier to improve operation
or to add new features. To update the firmware on your
amplifier you will need to connect it through the USB port
to a computer with Fender FUSE software and an internet
connection.

Please see the Fender FUSE manual at www.fender.

♫

com/support for details.

FAQ

Please see the Fender FUSE manual at www.fender.

♫

com/support for details.

• Record and edit Mustang audio using Ableton® Live Lite 8
Fender® Edition software.

Please see the Ableton® Live Lite 8 Fender edition at

♫

www.fender.com/support for details.

There are several great places you can go to learn more about
the Mustang and music in general:

• www.fender.com/support

• Join a Fender Community forum where you can ask
questions and read threads. There's even a forum just for
the Mustang: www.fender.com/community/forums

• Find music theory learning materials and sheet music at
Hal Leonard Publications: www.halleonard.com

fender.com

13

有毒有害物质或元素

部件部件名称

(Part Name)

铅

(PB)

部分电子元件
部分机器加工金属部件
部分其他附属部件

O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的现量要求以下
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的现量要求

x o o o o o
x o o o o o
x o o o o o

(Hazardous Substances’ Name)

汞

(Hg) 镉 (Cd)

六价铬

(Cr6+)

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

This product is covered by one or more of the following patents:

US Pat. 6,222,110

AMPLIFICADOR DE AUDIO

IMPORTADO POR: Instrumentos Musicales Fender S.A. de C.V., Calle Huerta # 132, Col. Carlos Pacheco, C.P. 228890, Ensenada, Baja California, Mexico.

RFC: IMF870506R5A Hecho en China. Servicio de Cliente: 001-8665045875

A PRODUCT OF:

FENDER MUSICAL INSTRUMENTS CORPORATION

CORONA, CALIFORNIA, USA

Fender®, Mustang™ and Fender® FUSE™ are trademarks of FMIC.
Other trademarks are property of their respective owners.
Copyright © 2013 FMIC. All rights reserved. (ENGLISH) rev a