Fairchild Semiconductor MM74HC126SJ, MM74HC126MTCX, MM74HC126MX, MM74HC126M, MM74HC126SJX Datasheet
...
September 1983
Revised February 1999
MM74HC125/MM74HC126 3-STATE Quad Buffers
© 1999 Fairchild Semiconductor Corporation DS005308.prf www.fairchildsemi.com
MM74HC125/MM74HC126
3-STATE Quad Buffers
General Description
The MM74HC125 and M M74HC126 are general pu rpose
3-STATE high speed non-inverting buffers utilizing
advanced silicon-gate CMOS technology. They have high
drive current outputs which enable high speed operation
even when driving l arge bus capacitan ces. These circuits
possess the low power dissipation of CMOS circuitry, yet
have speeds compar able to low power Schott ky TTL circuits. Both circuits are capable of driving up to 15 low
power Schottky inputs.
The MM74HC125 r equire the 3-STATE control input C to
be taken high to put the output into the high impedance
condition, whereas the MM74HC126 require the control
input to be low to put the output into high impedance.
All inputs are protected from damage due to static discharge by diodes to V
CC
and ground.
Features
■ Typical propagation delay: 13 ns
■ Wide operating voltage range: 2–6V
■ Low input current: 1 µA maximum
■ Low quiescent current: 80 µA maximum (74HC)
■ Fanout of 15 LS-TTL loads
Ordering Code:
Devices also availab le in Tape and Reel. Specify by appending th e s uffix let t er “X” to the ordering cod e. (Tape and Reel not available in N14A.)
Connection Diagrams
Pin Assignments for DIP, SOIC, SOP and TSSOP
Top View (MM74HC125)
Top View (MM74HC126)
Truth Tables
Order Number Package Number Package Description
MM74HC125M M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow Body
MM74HC125SJ M14D 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
MM74HC125MTC MTC14 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
MM74HC125N N14A 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
MM74HC126M M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow Body
MM74HC126SJ M14D 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
MM74HC126MTC MTC14 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
MM74HC126N N14A 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
Inputs Output
AC Y
HL H
LL L
XH Z
Inputs Output
AC Y
HH H
LH L
XL Z
www.fairchildsemi.com 2
MM74HC125/MM74HC126
Absolute Maximum Ratings(Note 1)
(Note 2)
Recommended Operating
Conditions
Note 1: Absolute Maximum Ratings are those values beyond which dam-
age to the device may occur.
Note 2: Unless otherwise specified all voltages are referenced to ground.
Note 3: Power Dissipation temper ature dera ting — plas tic “N” packa ge: −
12 mW/°C from 65 °C to 85°C.
DC Electrical Characteristics (Note 4)
Note 4: For a power supply of 5V ±1 0% the worst c ase ou tput volta ges (VOH, and VOL) occur for HC at 4.5V. Thus the 4. 5V valu es shoul d be use d when
designing with this supply. Worst case V
IH
and VIL occur at VCC=5.5V and 4.5V respectively. (The VIH value at 5.5V is 3.85V.) The worst case leakage current
(I
IN
, ICC, and IOZ) occur for CMOS at the higher voltage and s o th e 6.0V values should be used.
Supply Voltage (VCC) −0.5 to +7.0V
DC Input Voltage (V
IN
) −1.5 to V
CC
+1.5V
DC Output Voltage (V
OUT
) −0.5 to V
CC
+0.5V
Clamp Diode Current (I
IK
, IOK) ±20 mA
DC Output Current, per pin (I
OUT
) ±35 mA
DC V
CC
or GND Current, per pin
(I
CC
) ±70 mA
Storage Temperature Range (T
STG
) −65°C to +150°C
Power Dissipation (P
D
)
(Note 3) 600 mW
S.O. Package only 500 mW
Lead Temperature (T
L
)
(Solderi ng 10 seconds) 260°C
Min Max Units
Supply Voltage (V
CC
)26V
DC Input or Output Voltage 0 V
CC
V
(V
IN
, V
OUT
)
Operating Temperature Range (T
A
) −40 +85 °C
Input Rise or Fall Times (t
r
, tf)
V
CC
= 2.0V 1000 ns
V
CC
= 4.5V 500 ns
V
CC
= 6.0V 400 ns
Symbol Parameter Conditions
V
CC
TA = 25°CTA = −40 to 85°CTA = −40 to 125°C
Units
Typ Guaranteed Limits
V
IH
Minimum HIGH Level 2.0V 1.5 1.5 1.5 V
Input Voltage 4.5V 3.15 3.15 3 .15 V
6.0V 4.2 4.2 4.2 V
V
IL
Maximum LOW Level 2.0V 0.5 0.5 0.5 V
Input Voltage 4.5V 1.35 1.35 1 . 35 V
6.0V 1.8 1.8 1.8 V
V
OH
Minimum HIGH Level V
IN
= VIH or V
IL
2.0V 2.0 1.9 1.9 1.9 V
Output Voltage |I
OUT
| ≤ 20 µA 4.5V 4.5 4.4 4.4 4.4 V
6.0V 6.0 5.9 5.9 5.9 V
V
IN
= VIH or V
IL
|I
OUT
| ≤ 6.0 mA 4.5V 4.2 3.98 3.84 3.7 V
|I
OUT
| ≤ 7.8 mA 6.0V 5.7 5.48 5.34 5.2 V
V
OL
Maximum LOW Level V
IN
= VIH or V
IL
2.0V 0 0.1 0.1 0.1 V
Output Voltage |I
OUT
| ≤ 20 µA 4.5V 0 0.1 0.1 0.1 V
6.0V 0 0.1 0.1 0.1 V
V
IN
= VIH or V
IL
|I
OUT
| ≤ 6.0 mA 4.5V 0.2 0.26 0.33 0.4 V
|I
OUT
| ≤ 7.8 mA 6.0V 0.2 0.26 0.33 0.4 V
I
OZ
Maximum 3-STATE Output V
IN
= VIH or V
IL
6.0V ±0.5 ±5 ±10 µA
Leakage Current V
OUT
= VCC or GND
Cn = Disabled
I
IN
Maximum Input Current V
IN
= VCC or GND 6.0V ±0.1 ±1.0 ±1.0 µA
I
CC
Maximum Quiescent V
IN
= VCC or GND 6.0V 8.0 80 160 µA
Supply Current I
OUT
= 0 µA
Loading...