Page 1
5CFB--
5CFB
5CFB-100XIS
ISLAND CANOPY
ISLAND CANOPY
ISLAND CANOPY
Installation and Operation Manual
100XIS
100XIS
Page 2
1
7
6
5
2
4
3
2
1
4
6
7
5
3
2
4
1
5
6
7
3
7
6
5
4
3
2
1
7
6
5
2
4
1
3
6
5
2
7
3
1
7
6
1
3
2
5
4
4
1A
1B
1C
1D
1F
1G
1H
Page 3
g
g
j
h
i
g
g
f
f1
f2
2
3
4A 4B 4C
Page 4
3
4
4
4
4
4
4
6
6
7
7
7
7
8
8
2a
2a
2a
5
7
9
10
10
10
10
11
11
14,5
273
273
244
214
190
6
12
2b
2a
2b
S
B
5
Page 5
15
15
15
15
15
16
16
15
15
13A
15
14
H
13F
F
G
6
Page 6
18
18
18
18
18
18
18
18
18
18
M
17
19
X
X
20
20
19
17
7
Page 7
12
Consult the designs in the front pages referenced in the text
by alphabet letters. Closely follow the instructions set
out in this manual. All responsibility, for any eventual
inconveniences, damages or fires caused by not complying
with the instructions in this manual, is declined.
The cooker hood must be placed at a minimum distance of 50 cm
from the cooking plane for electric cookers and 75cm for gas or
mixed cookers.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only.
The hood is equipped with a top air outlet B for discharge of fumes
to the outside (Ducting version exhaust pipe and pipe fixing
clamps not provided).
Should it not be possible to discharge cooking fumes and vapour to
the outside, the hood can be used in the filter version, fitting an
activated carbon filter and the deflector F
on the support (bracket) G, fumes and vapours are recycled through
the top grille H by means of an exhaust pipe connected to the top air
outlet B and the connection ring mounted on the deflector F (exhaust
pipe and pipe fixing clamps not provided).
The models with no suction motor only operate in ducting mode, and
must be connected to an external suction device (not supplied).
Expansion wall plugs are provided to secure the hood to most types
of walls/ceilings. However, a qualified technician must verify suitability
of the materials in accordance with the type of wall/ceiling. The wall/
ceiling must be strong enough to take the weight of the hood.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only.
Do not fix chimney flue to furniture or fly over shelves unless the
chimney flue can be easily removed, in case maintenance is ever
required.
Installation - Fig. 5-6-7
Preliminary information for installing the hood
Assembling the deflector (Fig. 6 - 3 parts only for filter version):
The three parts should be fixed with 2 screws, the deflector extension
is adjustable and should correspond to the width of the chimney flue
support, to which it is then fixed.
During electrical connection ensure the power supply is disconnected
at the domestic main switch.
1. Adjust extension of the hood support structure, as the final
height of the hood depends on this, and remember that with
installation completed the hood must be at least 50 cm above the
cook-top for electric cookers and 75 cm for gas or mixed
cookers.
2. a. Fix the two sections of the structure using 8 screws.
b. If the hood is provided with extensions longer than the
minimum, fit the reinforcement bracket S to the frame, using 4
screws.
3. Place the ceiling hole diagram directly above the cook-top (the
center of the diagram must match the center of the cook-top and
the edges must be parallel to the sides of the cook-top the side
of the diagram with the wording FRONT corresponds to the
control panel side). Prepare the electrical connection.
4. Drill as shown (6 holes for 6 wall plugs 4 plugs for fixture),
screw the outer screws leaving a space of about 1 cm. between
the screw head and the ceiling.
5. Fit an exhaust pipe inside the truss and connect it to the motor
compartment connection ring (exhaust pipe and fixing brackets
are not supplied).
6. Hook the frame onto the 4 screws (see step 4).
CAUTION! The side of the truss with connection box corresponds
to the side of the control panel with hood assembled.
7. Tighten the 4 screws.
8. Insert and tighten another 2 screws in the remaining free holes
for secure fixing.
9. Carry out the electrical connection to the mains power supply,
only turn on the power supply upon completion of assembly.
10. Hook the hood onto the truss, ensuring it fits properly to hook
the hood onto the truss partially tighten 4 screws (see also step
12).
11. Secure the hood to the truss using two screws; this will also help
center the two sections.
12. Tighten the 4 screws securing the truss to the hood.
13. For extractor versions (13A), connect the other end of the
exhaust pipe to the flue.
For filter versions (13F), fit deflector F to the truss and secure it
to the bracket supplied using 4 screws, then connect the
exhaust pipe to the connection ring located on the deflector.
14. Fit the nuts with fixing hooks supplied inside the top and bottom
sections of the flues at the rectangular slots. A total of 10 nuts
must be fitted.
15. Join the two top sections of the flue to cover the truss so that one
of the slots on the sections is situated on the same side of the
control panel and the other on the opposite side. Screw the two
sections together with 4 screws (2 each side- see the plan
diagram for joining the two sections).
16. Fix the top flue assembly to the truss, near the ceiling, with two
screws (one each side).
17. Carry out electrical connection of control panel and bulbs.
Warning! Make connections taking care to insert the
connectors in the right way.
18. Join the two bottom sections of the flue covering the truss using
6 screws (3 each side, see the plan diagram for joining the two
sections).
19. Insert the bottom section of the flue in its seat so that it
completely covers the motor compartment and electrical
connection box, then ensure it from inside the hood using two
screws.
20. Apply the 2 tabs (supplied) to cover the fixing points of the
bottom flue (CAUTION! THE BOTTOM FLUE TABS ARE THE
NARROWER AND SHALLOWER ONES).
The wider and deeper tabs are those used for the top flue, and
must be cut to size.
21. Turn the mains power on again at the central electrical panel and
check for correct hood operation.
Electrical connection
The electrical tension must correspond to the tension noted on the
label placed inside the cooker hood. Connect the electrical plug,
where provided, to the an easily accessible outlet in conformity with
local standards in force.
Where an electrical plug is not provided (for direct connection to
electrical network) place a standards approved bipolar switch with
an aperture distance of not less than 3mm (accessible) from the
contacts.
Page 8
13
Description of the hood - Fig. 1
1 Control panel
2 Grease filter
3 Grease filter release handle
4 Halogen lamp
5 Vapour screen
6 Telescopic chimney
7 Air outlet (used for filter version only)
Operation
Model with electronic controls
1- Motor OFF button
2- ON button and motor speed selection button 1 - 2 - 3 -
1 - 2 - . . . .
3- Speed 1 LED
4- Speed 2 LED and metal grease filter saturation LED (in
this latter case, the LED will flash - See instructions on
grease filter cleaning).
Once the grease filters have been cleaned, press button
1 for about 3 seconds until you hear the acoustic signal
(beep): the LED 4 will now stop flashing.
5- Speed 3 LED and active carbon filter saturation LED (in
this latter case, the LED will flash - See instructions on
active carbon filter replacement).
Once you have replaced the charcoal filter, press button
1 for about 3 seconds until you hear the acoustic signal
(beep). LED 5 will now stop flashing.
Warning!
The active carbon filter saturation LED is not activated.
In order to activate the active carbon filter saturation
indicator, press buttons 2 and 7 simultaneously for 3
seconds. Initially, only LED 4 will flash, then after the
3 seconds have passed, LED 5 will also start flashing,
indicating that the active carbon filter saturation control
system is active.
To switch off the system, re-press the same two
buttons: after 3 seconds LED 5 will stop flashing and
the device will be switched off.
6 - Intensive speed LED
7 - Intensive speed ON switch
This speed should be used when the concentration of
cooking fumes or odours is particularly strong (for
example when frying, cooking fish etc.). T h e
fast speed will run for about 5 minutes and then return
to the speed previously set automatically (1, 2 or 3),
or switch off if no speed was selected.
To turn off the fast speed, before the end of the 5 minutes,
press button 1 or button 2.
8 - OFF lamp button
9 - ON lamp button
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
1
2
34
56
7
89
Operation
Model with button panel
A. on/off light switch
B. on/off aspiration switch and minimum power selection
B+C. medium power selection aspiration switch
B+D. maximum power selection aspiration switch
E. operating gauge (foreseen in the model with round buttons)
a. on/off light switch
b. off aspiration switch
c. minimum power selection aspiration switch
d. medium power selection aspiration switch
e. maximum power selection aspiration switch
ABCD
D
EF GH
A
BC
D
E
a
b
c
d
e
Page 9
14
Functioning - Model with display
A OFF key (Display off) /Stand-by (led lit on the display)
press for a long time to select the function desired.
B- Lighting, on/off.
C - Timer for selected speed (visualizes the speed selected
and flashing LED on the lower side of the display).
This knob permits the operation of the cooker hood for
a established period:
20 minutes if the speed selected is 1
15 minutes if the speed selected is 2
10 minutes if the speed selected is 3
5 minutes if the intensive speed P is selected.
D - Display showing:
Fan speed (1-3-P).
Change grease filters (grease filter saturation indicator
- F)
After washing the anti-grease filter, depress knob
A for about 3 seconds. The letter F will disappear
from the display.
Change activated carbon filters (carbon filter
saturation indicator - C).
After replacing the charcoal filter, depress knob
A for about 3 seconds. The letter C will disappear from
the display.
When the led in the lower right side is on, it indicates
that the cooker hood is ready for operation (standby
position), the flashing LED indicates that the timer has
been activated for selected speed.
Attention! The active carbon filter saturation indicator
is normally deactivated, to activate it:
Set the hood on OFF (display off), press keys C and
G contemporaneously for 3 secs.
Initially, only letter F will fbe displayed, then after the
3 seconds have passed, letter C will be displayed as
well, indicating that the carbon filter saturation control
system is active.
To switch off the system, re-press the same two
buttons: letter C appear on display and after 3 seconds
letter it disappear and the device will be switched off.
E - Knob to decrease the speed.
F - Knob to increase the speed.
G - Timed intensive speed button: the hood operates at this
speed for 5 minutes and than returns to the previus
settings. The display will show P and a blinking dot.
This function can be cancelled by pressing button A.
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
Warning!
Always press the fan off button A before disconnecting the
hood from the mains supply.
$%&' )(*
Operation
All cooker hood versions
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction
is switched on for 5 minutes prior to cooking and to leave
in operation during cooking and for another 15 minutes
approximately after terminating cooking.
Page 10
15
Maintenance
Prior to any maintenance operation ensure that the cooker
hood is disconnected from the power supply.
Cleaning: The cooker hood should be cleaned regularly
internally and externally.
For cleaning use a cloth moistened with denatured alcohol
or neutral liquid detergents. Avoid abrasive detergents.
Warning: Failure to carry out the basic standards of the
cleaning of the cooker hood and replacement of the filters
may cause fire risks.
Therefore we recommend observing these instructions.
Grease filter
This must be cleaned once a month (or when the filter
saturation indication system if envisaged on the model in
possession indicates this necessity see previous page)
using non aggressive detergents, either by hand or in the
dishwasher, which must be set to a low temperature and
a short cycle. When washed in a dishwasher, the grease
filter may discolour slightly, but this does not affect its filtering
capacity. To remove the grease filter, pull the spring release
handle (f) - (Fig. 2).
Charcoal filter (filter version only)
It absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two months
(or when the filter saturation indication system if envisaged
on the model in possession indicates this necessity see
previous page) using hot water and a suitable detergent,
or in a dishwasher at 65°C (if the dishwasher is used, select
the full cycle function and leave dishes out).
Eliminate excess water without damaging the filter, then
remove the mattress located inside the plastic frame and put
it in the oven for 10 minutes at 100° C to dry completely.
Replace the mattress every 3 years and when the cloth is
damaged.
Remove the filter holder frame by turning the knobs (g) 90°
that affix the chimney to the cooker hood (Fig. 3).
Insert the pad (i) of activated carbon into the frame (h) and
fit the whole back into its housing (j).
It is possible to use a traditional carbon filter, neither
washable nor regenerable, to be replaced every 3 - 4
months.
The filter holder frame of the carbon filter is welded together;
the eventual frame supplied with the hood is not, therefore,
to be used.
Insert it into its housing and fix it turning the 2 plastic knobs.
Replacing lamps - Fig. 4
Warning!
Prior to touching the light bulbs ensure they are cooled down.
For models shown in Fig. 1A:
1. press on the lamp cover and release to open. (fig. 4A).
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure you do
not touch them with your hands.
3. Close the lamp cover (it will snap shut).
For models shown in Fig. 1B-1C-1D-1G-1H:
1. Extract the guard by levering it off with a small screwdriver or
similar tool.. (fig. 4B).
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure you do
not touch them with your hands.
3. Close the lamp cover (it will snap shut).
For models shown in Fig. 1E:
1. Use a small screwdriver as a lever on the borders of the lamp in
order to remove the lightbulb. (fig. 4C).
2. Slide out the lightbulb to be replaced and replace with a new 12V
20W 30° Ø35 12V GU4 PHILIPS STANDARD LINE code
425409.
If the lights do not work, make sure that the lamps are fitted
properly into their housings before you call for technical
assistance.
Caution
This appliance is designed to be operated by adults. Children should
not be allowed to tamper with the controls or play with the appliance.
Do not use the cooker hood where the grill is not correctly fixed! The
suctioned air must not be conveyed in the same channel used for
fumes discharged by appliances powered by other than electricity.
The environment must always be adequately aerated when the
cooker hood and other appliances powered by other than electricity
are used at the same time. Flambé cooking with a cooker hood is
prohibited. The use of a free flame is damaging to the filters and may
cause fire accidents, therefore free flame cooking must be avoided.
Frying of foods must be kept under close control in order to avoid
overheated oil catching fire. Carry out fumes discharging in
accordance with the regulations in force by local laws for safety and
technical restrictions.
This appliance is marked according to the European directive
2002/96/EC on Waste Electrical and Electronic Equipment
(WEEE). By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences for the
environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
The symbol on the product, or on the documents
accompanying the product, indicates that this appliance may not
be treated as household waste. Instead it shall be handed over
to the applicable collection point for the recycling of electrical and
electronic equipment. Disposal must be carried out in accordance
with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and
recycling of this product, please contact your local city office,
your household waste disposal service or the shop where you
purchased the product.
Loading...