SAPE 69
ENGLISH
Instructions manual
Proximity card access control
Item 690
Card reader
partial recess
Item 694
Control
card
Item 691
Card reader
surface
Item 695
Control
keyring
Item 692
Receiver
Item 696
Special reader
partial recess
Item 693
Installation
cards
Management
Software
for PC
GB
page 8
Direttiva 2003/108/CE
I
Smaltimento dei materiali
elettrici ed elettronici
VIETATO GETTARE NEI RIFIUTI
MATERIALI NOCIVI PER L'AMBIENTE
l'apricancello
made in Italy
GB
Instructions manual SAPE 69 proximity card reader
BRINGING THE CARD READER APART
surface
mount
reader
pcb
IMPORTANT: It is possible to connect 2 readers maximum to one
Receiver.
!
Each reader must be identified when first installed: the strip jumper
must stay fitted onto one of the two, remove it from the other one.
FITTING ACCESSORIES FOR THE PARTIALLY RECESSED APPLICATION
Item 552
Item 558
Prit 19
Item 560
Sech 15
Item 553
Item 552
PROGRAMMING AND READING CARDS
GREEN (*) card:
to memorize the Blue cards
and the keyrings
(*): Cards to be used by the installation technician.
The two cards (Red and Green), at the time when the equipment is first
installed, are both memorized into the
Blanking or replacing them can only be carried out by the manufacturer
Meccanica Fadini after returning the removable memory.
Should a duplicate of the two cards (Red and Green) be required,
the number printed on the back is to be provided.
RED (*) card:
to memorize the Blue cards
and the keyrings
Removable memory.
BLUE card or keyring:
for the end user to open and
page 9
partial recess
mount
Item 554
The terminals for the
elec. connections
are on the back
SURFACE APPLICATION
FISSAGGIO DEL LETTORE ALLA PARETE
Z
Y
X
Pic.2
close the access
GREEN
RED
BLUE
The cards or the keyrings are actually read on
touching the reader; confirmation of the reading
is indicated by the illumination of a Blue Led and by a beep
sound from the receiver.
meccanica
FADINI
Pic.1
Pic.3
Pic.4
12V
GB
Instructions manual SAPE 69 proximity card reader
meccanica
FADINI
GENERAL DESCRIPTION
The proximity card reader SAPE 69 is a control accessory designed to open and close any automated access.
SAPE 69 consists of a reader, operated by magnetic cards or keyrings, and cable connected to the respective Receiver. The Receiver is fitted with a
removable memory, where the Blue cards or the keyrings and the installation Red and Green cards are memorized (during
the first installation and cannot be cancelled or replaced unless returned to the manufacturer). In the memory there are two independent lists where the
the users'cards can be memorized; each list can take up to 2,000 user's cards. The memorizing operations of the individual Blue cards or keyrings
are through Dip-swtch 1 or Dip-switch 2 set to ON. Cancelling is by Dip-switch 1 or 2 set to ON along with Dip-switch 3 to ON.
The Receiver elaborates the memorizing process of the cards and keyrings in the memory and confirms the operation by giving out a sound , while a
green led switches on. Cards or keyrings, that are not memorized in the lists, are indicated by a prolonged acoustic signal.
The reader allows only for the cards and keyrings to be read, which is confirmed by the blue led switching on. The installation of SAPE 69 is
completed after going through the programming phases: to make this process easier and quick, two types of cards are available, Red and Green.
They allow to memorize and cancel the end users' Blue cards and the keyrings, if required. The receiver is 230V 50Hz power supplied and provides a
12V output to power the readers, a relay output, a clean NO contact for remote switching applications if needed, and three inputs X - Y - Z
to communicate with the readers ("Z" to be used only in the case when the communication signal between reader - receiver is weak or disturbed).
It is possible to complete the equipment with a software to manage the entire system at a distance. In this way, an electronic data base can be
created to easily operate with SAPE 69 through a PC.
Elpro control box
Radio contact
or any opening
pulse
3 47
IMPORTANT: It is possible to connect
maximum n°2 Readers to each Receiver.
!
Each reader must be identified when first
installed: one must be fitted with the Strip,
this must be removed from the other one.
IMPORTANT: To prevent interfering, it is
recommended to install the readers at a
!
minimum distance of 50cm from each
other.
Connection to terminal Z is required
in case the signal is weak or disturbed.
Power supply
from control box
230V 50Hz supply from the mains.
The entire installation must be
properly earthed
2x0.5mm²
up to 100m
DIP-SWITCHES
The removable memory is designed to include 2 lists, each one can take
up to 1,000 possible cards. The two lists can be accessed and controlled
by Dip-Switches 1, 2 and 3.
ONOFF
123
Dip1 = ON allows access to List 1 to carr y on
Dip2 = ON allows access to list 2 to carry on
Dip3 = ON the entire memory is blanked by
card memorizing and cancelling.
card memorizing and cancelling
the RED card. Combined to
DIP-switch 1or 2 set to ON, only
the selected one list is blanked.
Receiver
Removable memory: the BLUE cards (in list 1and
list 2), and the RED and GREEN cards are
230V
50/60Hz
relay
12V
2x0.5mm²
up to 100m
123
CNO YXZ
memorized in it.
cannot be cancelled or replaced.
ONOFF
2x0.5mm²
up to 100m
Intermittent Red Led: indicates that the readers
are connected.
Red Led: it switches on during the memorizing
phase and on reading a non memorized
card
Green Led: it switches on when a memorized
card is being read.
Micro-USB 2.0 connection to PC.
Entry reader
!
Z
Y
X
Exit reader
The last ones, once memorized,
12V
!
Z
2x0.5mm²
up to 100m
ACOUSTIC SIGNAL
The acoustic signal helps with the memorizing and reading phases of
the cards or keyrings. This device is fitted in the receiver.
1
Pic.6 Pic.7
Y
X
12V
FISSAGGIO DEL LETTORE ALLA PARETE
Long Beep =A card
Single Beep = a new card is being memorized or a listed
Alternated
fast Beeps
not memorized in the list is being read.
When the memory is being blanked,
a sound is given out for 30 seconds.
card is being read.
= memorizing phase (by the Green card),
or blanking phase (by the
Red card).
50cm
Minim. distance
Pic.5
page 10
GB
Instructions manual SAPE 69 proximity card reader
meccanica
FADINI
MEMORIZING THE BLUE CARDS OR THE KEYRINGS
Important: when the equipment is first installed, and the Green card is read and therefore memorized into the system, the Red card is
automatically memorized, too. Both cannot be cancelled or replaced, only the manufacturer can do this.
!
In this way the installation is uniquely controlled by the possessor of the Green and Red cards.
1) Set to ON either DIP-sw. 1 or DIP-sw. 2 (only one of the two): Dip-sw. 1 to access list 1 (faster in reading than list 2),
and Dip-sw. 2 to access list 2
2) Bring the GREEN card to touch one reader (
The red led in the receiver starts flashing and a fast, alternate acoustic signal can be heard, indicating that the memorizing process is on.
3) Bring , one by one, the BLUE cards or the keyrings to touch the reader to have them memorized (the Blue led on the Reader switches on whenever a
card or a keyring is read; wait until it is off again before doing the same with other units).
4) Bring again the GREEN card to touch the reader once card/keyring memorizing is over. Should new cards/keyrings be required to be entered, wait 3
seconds and bring again the Green card to touch the reader.
Diagram
1)
1
ON ON
or
2)
2
in case of two readers. this operation can be carried on only with one of them).
3)
GREEN
BLUE
....
4)
GREEN
GB
Instructions manual SAPE 69 proximity card reader
meccanica
FADINI
SOFTWARE SAPE 69 FOR PC MANAGEMENT
General description
The SAPE 69 system, previously described as a simple electronic system operated through cards or keyrings, can be integrated with a software allowing
the user to create a data base of the entire installation.
The software allows the management of the two users' lists, once the user's cards and keyrings have been entered: it is possible to identify each single
card/keyring by including the end user's data (name and address), enable/disable each single card/keyring, remove any single card/keyring from
the lists and specify the period of use of any card/keyring by indicating an expiry date.
Important:
card or by PC.
memorizing the cards/keyrings is only by means of the GREEN card, whereas cancelling is made possible only by means of the RED
SAPE 69 system: simple installation without the help of the software
ELECTRONIC
CONTROL BOX RECEIVER ENTRY
(see Pic.6 for the electrical connections)
READER
READER
EXIT
receiver
NOTE: Once memorizing is completed, unless the GREEN card is brought to touch the reader in 1 minute's time, the procedure is closed,
but the cards/keyrings are retained in the memory. If the RED card is used by mistake, the procedure is interrupted.
reader
receiver receiver
reader
reader
Pic.8
INDIVIDUAL BLUE CARDS OR KEYRINGS CANCELLING
Should any card or keyring be lost, removal from the system can be done only through the software by a PC ( it is understood that the names of the
users/customers must be available in that they were previously memorized in the list), as an alternative the entire list is to be cancelled and the cards
memorized again.
1) Set to ON
2) Bring the RED card to touch one reader (
The red led in the receiver starts flashing and a fast, alternate acoustic signal can be heard, indicating that the cancelling process is on.
3) Bring, one by one, the BLUE cards or the keyrings to touch the reader to cancell them from the pre-selected list (the Blue led on the Reader switches
on whenever a card or a keyring is read; wait until it is off again before doing the same with other units).
4) Bring again the RED card to touch the reader once card/keyring cancelling is over. Should new cards/keyrings be required to be cancelled, wait 3
seconds and bring again the Red card to touch the reader.
NOTA: Once cancelling is completed, unless the RED card touches the reader in 1 minute's time, the procedure is closed, anyway the
previously cancelled cards/keyrings are no longer in the memory. If the GREEN card is brought to touch the reader by mistake, the
procedure is interrupted.
either DIP 1 or DIP 2 (only one of the two): Dip 1 to access list 1, Dip 2 to access list 2.
in case of two readers, this operation can be carried on only with one of them).
Diagram
1)
1
ON ON
or
receiver
2)
reader
RED
receiver
2
3)
BLUE
....
reader reader
4)
RED
receiver
Pic.9
TOTAL REMOVAL OF LIST 1 OR LIST 2
1) Set to ON the DIP corresponding to the list required to be removed: Dip 1 for list1, and Dip 2 for list 2.
Set to ON even DIP 3.
2) Bring the RED card to touch one reader (
The red led in the receiver goes on and a sound can be heard for 30 seconds. During this time the entire selected list is deleted.
But the two installer's cards, RED and GREEN, are not disabled.
3) Once the 30 seconds are over, the memory is blanked.
4) On the red led going off and the sound stopping, set all of the dip-switches to OFF.
Diagram
1)
ON
1
or
ON
2
++
receiver
in case of 2 readers, this operation can be carried on only with one of them).
2)
ON
3
reader
RED
3)
30 sec
receiver
4)
ALL OF THE DIP-SWITCHES TO OFF
OFF
1
OFF
or
receiver
OFF
2
3
Pic.10
page 11
230V - 50Hz from the
Connections of
mains
the system
communication 2x0.5mm²
power supply 2x0.5mm²
Pic.11
To facilitate the agent with the customer management by the PC, a special reader is combined to the software: once the special reader has been
connected to the receiver, it is possible to operate with the cards/keyrings avoiding that the gate/door is opened/closed during the management
(this reader is distinguished by
the colour of the electronic pcb being white).
Software for the management of the SAPE 69 system
Note: to make the software easier to be installed and managed, it is advisable that the Receiver be installed near to PC.
External automatic access
ENTRY
READER
230V - 50Hz from
the mains
connections
with the system
EXIT
READER
Electronic
control box
RECEIVER
READER to communicate the
data in the cards to the PC
(it is distinguished from the normal
readers by the white colour
of the pcb)
micro-USB 2.0
connection
NOT INCLUDED
WITH THE
EQUIPMENT
communication 2x0.5mm²
power supply 2x0.5mm²
CD with the software to
be installed onto a PC
Pic.12
page 12
GB
SAPE 69
Instructions manual SAPE 69 proximity card reader
SOFTWARE INSTALLATION
- Open the folder and select automatic installation of the software.
- Once the electrical connections are completed as detailed in Pic.6 and Pic.13, select the icon and run the program.
meccanica
FADINI
Instructions manual SAPE 69 proximity card reader
GB
OVERALL DIMENSIONS
Ø56
72
127
Housing box
for the receiver pcb
meccanica
FADINI
Pic.13
IMPORTANT:All of the data included in the cards/keyrings are stored in the removable memor y of the Receiver; before changing or updating the data
in the lists stored in the memory, it is required that the data (in list 1 and list 2) are made available in the PC by clicking
"READ CARD LIST". After changing/updating the user's data, it is required to update the receiver memory by clicking
"WRITE CARD LIST".
ACQUIRING THE DATA FROM THE RECEIVER MEMORY:
After opening the software, it is necessar y to acquire the data from the receiver Memory by clicking "READ CARD LIST" and wait until the operation is
finished. Second step, the data are to be saved as; and an error window appears (to be ignored).
IMPORTANT: whenever the software is run and in order to update the data in the memory (once a day at least, preferibly on star ting the system),
it is recommended to acquire the data from the receiver memory (READ CARD LIST) and then update it (WRITE CARD LIST).
NAMING AND CUSTOMIZING THE CARDS/KEYRINGS:
In the case where users' cards/keyrings have already been stored into the system, the window of the provided software shows all the available data.
In the case where the installation is new and no data have been stored yet in the two lists, it is required to "load the memory" with the available data
(by means of the GREEN card, standard procedure as on page 11) and then pass them on to the PC through the "Communication reader".
Select the previously stored user's card/keyring in the column "CUSTOMER DATA". Click "MODIFY" to be allowed to enter the following sections and
change the data as required:
- "FIRST NAME", "LAST NAME", "ADDRESS", "NOTES": enter the available information to customize the selected card/keyring.
- "ENABLE": if the box is "ticked", the card/keyring is enabled for access operations. If a new card/keyring is required to be enabled,
"tick" the box and, once the new entry is saved, click "WRITE CARD LIST" to send the information to the receiver memor y.
Note: The box in the column "DISABLED" shows "X" if the respective card/keyring is disabled.
- "LIST": when the card/keyring is being read, it is indicated in which list it is stored. In the case of a new card/keyring it is possible to indicate in which list it
can be saved by "ticking" "1" or "2" and clicking "WRITE CARD LIST".
- "CARD CODE": when a card/keyring is being read, an identification internal code is visualized.
- "EXPIRY DATE": It is possible to set a date of expiry to the period of time a card/keyring can be used by its possessor. Important: once a day at least
click "WRITE CARD LIST" to update the dates in the memory (
- "CANCEL": it is possible to individually cancel the cards/keyrings from the memory by clicking "CANCEL", without moving the Dip-switches in the receiver;
N.W. The cards/ keyrings are loaded into the memory always and exclusively by the GREEN card ( page 11).
- "SEARCH": it is possible to search a card/keyring in the created data base either by the NAME OF THE CUSTOMER or by the CODE number.
ESPORTING THE DATA BASE TO A FILE:
It is possible to export the file you are working with and containing the entire list of the cards/keyrings in the memory by clicking "EXPORT CARD LIST".
A .txt file is thus created having the same name, in the same folder. It will be then possible to print it in a personalized format through other programs
(eg. excel).
recommended on starting the system, or every day in the early morning).
page 13
2525
50
Reader
partially recessed
TECHNICAL DATA
Receiver voltage supply
Reader supply (from the receiver)
Reader max. absorption, each
Receiver max. absorption
Working temperature
NO output channels
Communication distance
Output contacts
Reader protection standards
Receiver protection standards
Memory List 1
Memory List 2
The manufacturer reserves the right to change this manual without
notice, and is not liable for incorrect applications and damages
to persons and properties.
230Vac ±10% - 50Hz
12V
50 mA
10 mA
-20° +80°C
1
max 100 m
1A - 125V - 60VA
IP 56
IP 65
2'000 cards
2'000 cards
3670
Reader
surface mounted
87
57
Receiver
Receiver pcb
complete with
removable memory
DECLARATION OF CONFORMITY
of the Manufacturer
meccanica
Manufacturing company:
Model:
Sape 69 is an access control proximity system and is designed and sold to be incorporated into an
"automatic gate system", including original accessories and components as recommended by the
Manufacturing Company. The installer must issue a Declaration of Compliance and carry out all the
tests as required to comply with the existing safety regulations.
The Manufacturing Company is not liable for any incorrect application of the product.
The product complies with the following applicable norms:
- Low Voltage Directive
- Electro-magnetic Compatibility Directive
GB
Date:
page 14
FADINI
DECLARES UNDER ITS OWN RESPONSIBILITY THAT:
20 - 04- 11
Via Mantova 177/A - C.P. 126 - 37053 Cerea (VR) Italy
Tel. +39 0442 330422 - Fax +39 0442 331054
e-mail: info@fadini.net - www.fadini.net
2006/95 CE
2004/108/CE and 92/31 CEE
Meccanica Fadini s.n.c.
Responsible Manager
The Responsible Manager
Pic.14
the gate opener
made in Italy
Loading...