EPSON ELP-3300 User Guide

PLEASE READ

We are in no way responsible for the contents of the manual. We do not guarantee its accuracy and we do not make any claim of copyright. The copyright remains the property of their respective owners.

Visit the site to read the latest projector news and reviews, read and comment on projector specifications, download user manuals and much more.

EPSON

Owner’s Manual

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by Seiko Epson Corporation.

EPSON is a registered trademark of Seiko Epson Corporation. EPSON Connection is a service mark of Epson America, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.

The Energy Star emblem does not represent EPA endorsement of any product or service.

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

DOC (for Canadian Users)

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment regulations. Cet appareil numérique de la Classe A respecte toutes les exigences du Réglement sur le materiel brouilleur du Canada.

Apple Warranty Disclaimer

Apple Computer, Inc. (“Apple”) makes no warranties, express or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose, regarding the Apple software. Apple does not warrant, guarantee or make any representations regarding the use or the results of the use of the Apple software in terms of its correctness, accuracy, reliability, currentness or otherwise. The entire risk as to the results and performance of the Apple software is assumed by you. The exclusion of implied warranties is not permitted by some states. The above exclusion may not apply to you.

In no event will Apple, its directors, officers, employees or agents be liable to y o u for any consequential, incidental or indirect damages (including damages for loss of business profits, business interruption, loss of business information, and the like) arising out of the use or inability to use the Apple software even if Apple has been advised of the possibility of such damages. Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitations may not apply to you. Apple’s liability to you for actual damages from any cause whatsoever, and regardless of the form of the action (whether in contract, tort (including negligence), product liability or otherwise), will be limited to $50.

Energy Star Compliance

EPSON is an Energy Star Partner and this projector complies with the Energy Star program's guidelines for energy efficiency.

iii

Important Information About Your ELP-3300

Please read the following important information about your ELP-3300 projector.

Important Safety Information

WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on.

WARNING: Never open any cover on the projector, except the lamp, fuse, and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this Owner’s Manual, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

Caution: When you replace the lamp, never touch the new bulb with your bare hands; the invisible residue left by the oil on your hands may shorten the bulb life. Use a cloth or glove to handle the new bulb.

Remote Control Information

The ELP-3300 allows you to operate it by remote control via infrared (IR) receivers located at the front and back of the projector. The projector may not respond to remote control commands under the following conditions:

• The ambient light is too bright

iii

• Certain types of fluorescent lighting are used

• A strong light source shines into either IR receiver

• Other equipment that emits infrared energy, such as a radiant room heater, is in the room.

These conditions commonly cause problems for most infrared-controlled equipment. Try the following solutions:

• The remote control unit’s batteries may be low on power; replace them.

• Dim the ambient lighting and/or turn off any fluorescent lights.

• Close any window coverings and/or move the projector out of direct sunlight.

• Turn off other equipment that emits infrared energy.

If the remote control still does not work properly, cover the unused IR receiver on the projector with light-blocking material, such as masking tape. Remember you can always control your computer-based presentation directly from the computer, even in an environment containing one of the conditions listed above.

README File Information

The diskettes that came with your projector include README files that contain additional important information about the projector. Be sure to read these files.

Introduction

Getting the Most Out of Your Projector x Optional Accessories xii About This Manual xiii Safety Instructions xiv Where to Get Help xvi

Electronic support services xvii

Energy Star Compliance xviii

1 Installation 1

Unpacking the Projector 2

Additional components 3 Setting Up the Projector 4 Connecting to a Computer 6

Connecting to a PC desktop computer 7

Contents

Connecting to a PC laptop computer 8 Connecting to a desktop Macintosh 9 Connecting to a PowerBook 10

Connecting to a Video Source 11 Connecting to an Audio Source 13 Connecting to an External Speaker or PA System 14 Setting Up Serial Communication 15

Connecting the serial cable 15 Installing the software 16

Connecting the Remote Control with the Lead Wire 17

2 Using the Projector 19

Turning the Equipment On and Off 20 Focusing and Positioning the Screen Image 21 Controlling the Projector 23

Adjusting the settings from ELP Link 26

Monitoring the Projector 27 Using Rear Projection 28

3 Using the Menus 29

Accessing the Menus 30

Changing menu settings 31 Accessing ELP Link menus 32 Restoring the default settings 33

Menu Settings 33

Contents

Computer menu 34

Video menu 36

Display menu 37

Audio menu 39

Options menu 40

Custom menu 41

4 Remote Control of the Computer 43

ELP Remote Programmer Templates 44 Starting the ELP Remote Programmer 45 Assigning a Macro to a Programmable Button 48

Using record mode 49

Using manual mode 51 Activating a Template 51 ELP Remote Programmer Menus 52

5 Maintenance 53

Cleaning the Lens 54 Cleaning the Projector Case 54 Cleaning the Air Filter 54 Cleaning the Trackball 56 Replacing the Lamp 58

Resetting the lamp timer 61 Replacing the Fuse 62

Contents

vii

6 Troubleshooting 65

Problems with the Projector 66 Problems with the Image or Sound 69 Problems with the Remote Control 72

A Technical Specifications 75

General 75 Optical 76 Projector Lamp 76 Mechanical 76 Electrical 77 Environmental 77 Supported Monitor Displays 78 Pin Assignments 79

Glossary 81

Index 85

viii

Contents

Introduction

he compact, lightweight EPSON® ELP-3300 Projector allows you to project computer images and video onto a large screen for full-color presentations. The projector can connect simultaneously to two image sources; one can be your PC or Apple VCR, camcorder, digital camera, or laser disk player. Audio can be supplied with one or both image sources.

Macintosh® computer and the other can be a video source, such as a

Images are displayed in up to 16 million colors at a resolution of 640

x 480

pixels. The projector’s 300-lumen bulb produces bright images that can be easily seen in rooms light enough to take notes. You can play audio on the projector’s internal speakers or route it to an external speaker for amplification. You control the projector through a hand-held remote control, which allows you to switch between image sources and make adjustments to the projected image.

The projector supports any computer capable of VGA output, including IBM compatible PCs and laptops and Apple Macintosh computers, including the PowerBook

and Power Macintosh.

The video source can be NTSC, PAL,

and SECAM in composite video or S-Video format.

Getting the Most Out of Your Projector

The projector comes with a full set of features that allow you to control the settings for the image display, video, and audio. To get the most out of your projector, read this section for a quick summary of the important features.

Remote control

The buttons on the remote control allow you to directly change the volume, control the brightness, or switch from one image source to the other. Additional adjustments can be made by using the buttons on the remote control to access the projector’s menu system.

The menus, which you can superimpose on the projector image or display on your computer screen, allow you to do the following:

• Control the brightness, contrast, sharpness, color, and position of the image.

• Adjust the volume, balance, treble, and bass settings.

• Adjust the display by rotating or inverting it.

Additional settings are described in Chapter 3.

You can also use the remote control to control your computer if you install the Serial Communication Kit.

Introduction

Serial Communication Kit

The Serial Communication Kit allows your computer and projector to communicate over an RS-232C connection. The kit includes an RS-232C serial cable and two software utilities: ELP Link and ELP Remote Programmer.

• ELP Link allows you to make adjustments to the projector from your computer.

The same controls that are available on your remote control, including the ability to access the projector menus, are available from the main ELP Link screen.

• The ELP Remote Programmer allows you to use the remote control to control

your computer. The trackball moves the mouse on your computer monitor, and five buttons on the remote control can be programmed to drag or click windows and icons or perform the same functions as keys on your keyboard.

For information on using ELP Link, see Chapters 2 and 3. For information on the ELP Remote Programmer, see Chapter 4.

Standby mode

Standby mode conserves electricity by automatically turning off the lamp if the projector has not been used for a specified period of time (the default is 10 minutes). In standby mode, the projector remains on but the lamp is turned off. This conserves electricity, cools the projector, and extends the life of the lamp.

Use the Standby button on the remote control to turn standby mode on or off.

Getting the Most Out of Your Projector

Rear projection

If you have a translucent screen, you can set up the projector for rear projection, in which the projector sits behind the screen. To use the remote control with rear projection, you need to purchase the optional lead wire and connect the remote control directly to your computer.

Optional Accessories

To enhance your use of the projector, EPSON provides the following accessories:

• Polarized screens designed specifically for use with the projector. They allow you to project images in a bright, illuminated room, making it unnecessary to dim lights to view the projected image. The polarized screen comes in two sizes: 40" and 60" diagonal.

• Carrying cases especially designed for the projector and its cables. Both a soft and hard case are available.

• Remote control lead wire, which allows you to directly connect the remote control to the projector. This option enables you to use the remote control when an object is blocking the path between the remote control and projector, such as during rear projection when the screen is between the remote control and the projector.

xii

You can purchase these accessories from your ELP-3300 dealer or by calling EPSON Accessories at (800) 873-7766.

Introduction

About This Manual

Chapter 1, “Installation,” gives step-by-step instructions on setting up the projector and connecting it to your computer, video source, and optional other equipment. Read the installation procedures that apply to your environment.

Chapter 2, “Using the Projector,” tells you how to turn on the projector; control simple projector settings using the remote control, the operation panel, and the ELP Link software; and set up the projector for rear projection.

Chapter 3, “Using the Menus,” describes how to use the menus to adjust the color and image settings, change the display of the projected image, and modify audio settings such as bass or treble.

Chapter 4, “Remote Control of the Computer,” explains how to use the ELP Remote Programmer so you can use the remote control to control your computer. It also describes how you can assign keyboard macros to the programmable buttons on the remote control.

Chapter 5, “Maintenance,” describes how to maintain the projector in good working order.

Chapter 6, “Troubleshooting,” tells you how to interpret the projector’s status lights and gives helpful information for avoiding errors, optimizing image quality, and solving problems.

Appendix A provides technical specifications.

About This Manual

xiii

Safety Instructions

Follow these safety instructions when setting up and using the projector:

1. Do not place the projector on an unstable cart, stand, or table.

2. Do not use the projector near water or sources of heat.

3. Use attachments only as recommended.

4. Use the type of power source indicated on the projector. If you are not sure

of the type of power available, consult your dealer or local power company.

5. Insert the projector’s three-wire grounding-type plug into a properly

grounded outlet. If you have a two-prong outlet, contact an electrician to replace it.

6. Do not overload wall outlets, extension cords, or integral convenience

receptacles. This can cause fire or electric shock.

7. Do not place the projector where the cord can be walked on.

8. Unplug the projector from the wall outlet before cleaning. Use a damp cloth

for cleaning. Do not use liquid or aerosol cleaners.

xiv

9. Do not block the slots and openings in the projector case. They provide

ventilation and prevent the projector from overheating. Do not put the projector on a sofa, rug, or other soft surface or in a built-in installation unless proper ventilation is provided.

Introduction

10. Never push objects of any kind through cabinet slots. Never spill liquid of any kind in the projector.

11. Except as specifically explained in this Owner’s Manual, do not attempt to service this product yourself. Opening or removing covers may expose you to dangerous voltages and other hazards. Refer all servicing to qualified service personnel.

12. Unplug the projector during lightning storms or when it will not be used for extended periods.

13. Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into it or it has been exposed to rain or water.

C. If it does not operate normally when the operating instructions are

followed or if it exhibits a distinct change in performance, indicating a need for service.

D. If it has been dropped or the cabinet has been damaged.

Safety Instructions

Where to Get Help

If you purchased your projector in the United States or Canada, EPSON provides customer support and service through a network of authorized EPSON Customer Care Centers. EPSON also provides the following services when you dial (800) 922-8911:

• EPSON Technical information library fax service

• Product literature on current and new products

• Assistance in locating your nearest Authorized EPSON Reseller or Customer Care Center

• Technical information on the installation, configuration, and operation of EPSON products

• Customer relations.

You can purchase supplies, parts, printed manuals, and accessories for EPSON products by calling EPSON Accessories at (800) 873-7766 (U.S. sales only). In Canada, call (800) BUY-EPSON for sales locations.

xvi

If you purchased your projector outside the United States or Canada, contact your EPSON dealer or the marketing location nearest you for customer support and service.

Introduction

Electronic support services

If you have a modem, you can access helpful tips, specifiations, drivers, application notes, and bulletins for EPSON products through the online services below.

EPSON Download Service

You can call the EPSON Download Service (our BBS) at (310) 782-4531. No membership is required. Make sure your communications software is set to 8 data bits with 1 stop bit, no parity bit, and a modem speed up to 28.8 Kbps. See the manual that came with your communications software for more information.

CompuServe® online support

CompuServe members can call the Epson America Forum on CompuServe. If you are already a member, simply type GO EPSON at the menu prompt to reach the Epson America Forum. If you are not currently a member of CompuServe, you are eligible for a free introductory membership as an owner of an EPSON product. This membership entitles you to:

• An introductory credit on CompuServe

• Your own user ID and password

• A complimentary subscription to CompuServe Magazine, CompuServe’s monthly publication.

Where to Get Help

xvii

To take advantage of this offer, call (800) 848-8199 in the United States and Canada and ask for representative #529. In other countries, call (614) 529-1611 or your local CompuServe access number.

World Wide Web site

If you are connected to the Internet and have a Web browser, you can access EPSON's World Wide Web site at http://www.epson.com. EPSON’s home page links users to What’s New, EPSON Products, EPSON Connection, Corporate Info, and EPSON Contacts. Link to the EPSON Connection for the latest drivers and FAQs (Frequently Asked Questions) and the EPSON Chat area. To get in touch with EPSON around the world, EPSON Contacts includes Contact Information for local EPSON subsidiaries.

Energy Star Compliance

As an Energy Star Partner, EPSON has determined that this product meets the Energy Star guidelines for energy efficiency. The EPA estimates that if all desktop computers, printers, and other peripheral devices met Energy Star standards, energy cost savings would exceed $1 billion annually and carbon dioxide emissions would be reduced by 20 million tons.

xviii

Introduction

Installation

his chapter describes how to unpack, set up, and connect your projector to other equipment. You must connect the projector to your computer or to a video source such as a VCR, camcorder, digital camera, or laser disk player. Connecting to other equipment is optional. For example, you may want to connect the projector to both your computer and video source, or set up the projector for one or more of the following:

• Provide audio for one or both image sources. The audio source can be the

computer, video source, or another device such as a stereo.

• Connect to an external speaker or PA system to amplify the audio.

• Install the RS-232C Serial Communication Kit. This kit enables communication

between your computer and the projector so you can use the remote control to control your computer and use your computer to control the projector settings.

• Directly connect the remote control and the projector using the optional lead

wire. You need to do this to use the remote control for rear projection.

Unpacking the Projector

When you unpack the projector, make sure you have all these components:

• Projector

• Remote control

• 2 AA batteries

• Power cord

• Y-shaped VGA cable

• 2 Macintosh adapters (labeled VGA and MONITOR)

• Lens cover

• Video/audio cable

• RS-232C serial communication kit, which consists of an RS-232C serial cable, an RS-232C adapter for the Macintosh, and two diskettes (one for the Macintosh, and one for the PC)

• Spare fuse.

Depending on your configuration, you may not need all of these components.

Save all packaging materials in case you need to ship the projector in the future. It should always be transported in its original packaging or the equivalent.

2 1 • Installation

Additional components

Depending on how you plan to use the projector, you may need to obtain additional components:

• To receive audio from both the computer and video source, you need a second video/audio cable. See your computer dealer to obtain one.

• To receive an S-Video signal, you need an S-Video cable. One is usually provided with your video device.

• For a Macintosh PowerBook, you need a video-out cable. One is provided for all new PowerBooks that have video-out capability. If your PowerBook does not include one, see your Macintosh dealer.

• To connect the projector to external speakers, you need an RCA-to-3.5mm audio cable. You can obtain one from your computer dealer.

• If your PC has a 25-pin RS-232C port, you need a 25-pin to 9-pin converter. You can obtain one from your computer dealer.

Unpacking the Projector

Setting Up the Projector

1. Place the projector on a sturdy, level surface within five feet of the computer or video source.

◆ Caution: Do not hold the projector by the lens when you move it. This

will damage the lens.

2. Place the projector the proper distance from the screen.

The distance between the projector and the screen determines the actual image size. Use the following general guidelines to determine the proper distance.

Maximum Zoom Minimum Zoom

300 inches (25 feet) 214 inches (30 feet) 40 feet 204 inches 146 inches 27 feet 96 inches 69 inches 13 feet 60 inches 42 inches 8 feet 30 inches 21 inches 4 feet

Image size Distance from screen

(diagonal) (approximate)

3. Turn the projector so the lens is at a right angle to the screen. If the projector is not at a right angle, the screen image will be crooked.

4 1 • Installation

4. Connect one end of the power cord to the projector’s power connector. Connect the other end to a grounded electrical outlet.

If the projector comes on, turn it off using the power switch at the back of the projector.

5. To insert the batteries in the remote control, slide off the battery compartment cover as shown here.

6. Insert the two AA batteries included with the projector. Make sure the polarity of the batteries is correct.

7. Replace the battery compartment cover.

Setting Up the Projector

When replacing batteries, take the following precautions:

• Do not mix old and new batteries.

• Replace batteries as soon as they run out. If the batteries leak, wipe away the fluid with a soft cloth. If battery fluid gets on your hands, wash immediately.

• Remove batteries if you will not be using the projector for long periods.

Connecting to a Computer

You can connect the projector to any computer capable of VGA output, including:

• IBM desktop PC or compatible

• IBM laptop or compatible

• Apple Macintosh desktop computer, including Macintosh Quadra, Centris,

• Any Apple PowerBook with video-out capability. This includes all 160, 165, 180, and 500 series PowerBooks.

See the following section that applies to your computer.

6 1 • Installation

and Power Macintosh

Macintosh

Connecting to a PC desktop computer

Before beginning, turn off the projector and computer if they are on. To access the connectors on the projector, push open the cover located on the right side of the projector, under the handle.

1. Disconnect the computer’s monitor cable from the VGA port on the back of your computer and connect it to the MONITOR connector of the Y-cable.

2. Connect the Y-cable’s VGA connector to the computer’s VGA port.

3. Connect the Y-cable’s LCD connector to the projector’s Computer IN/OUT port.

4. Tighten the screws for all connectors to make sure they are fastened securely.

monitor cable

MONITOR connector

VGA port

VGA connector

LCD connector

Connecting to a Computer

Computer

Computer In/Out

Audio In

S-Video

Connecting to a PC laptop computer

Before beginning, turn off the projector and computer if they are on. To access the connectors on the projector, push open the cover located on the right side of the projector, under the handle.

1. Connect the LCD connector on the Y-cable to the projector’s Computer IN/OUT port.

2. Connect the VGA connector on the Y-cable to the laptop’s monitor port.

3. Tighten the screws for all connectors to make sure they are fastened securely.

2 1

VGA connector

MONITOR connector

LCD connector

Computer

Computer In/Out

Audio In

S-Video

When the external graphics port is activated, some laptop computers automatically turn off their internal display. See your computer manual for information on using the internal display.

8 1 • Installation

Connecting to a desktop Macintosh

Before beginning, turn off the projector and Macintosh if they are on. To access the connectors on the projector, push open the cover located on the right side of the projector, under the handle.

1. Attach the Macintosh adapters provided with the projector to the appropriate connectors on the Y-cable. Connect the MONITOR adapter to the MONITOR connector (1a), and connect the VGA adapter to the VGA connector (1b).

2. Disconnect the monitor cable from the monitor port on the back of the Macintosh and connect it to the MONITOR Macintosh adapter.

3. Connect the VGA adapter (attached to the Y-cable) to the Macintosh’s monitor port.

4. Connect the Y-cable’s LCD connector to the projector’s Computer IN/OUT port.

5. Tighten the screws for all connectors to make sure they are fastened securely.

Macintosh monitor cable

MONITOR adapter

monitor port

VGA adapter

VGA connector

LCD connector

MONITOR connector

Connecting to a Computer

Computer

Computer In/Out

Audio In

S-Video

Connecting to a PowerBook

Your PowerBook must have a video-out capability. See page 6 for more information.

Before beginning, turn off the projector and computer if they are on. To access the connectors on the projector, push open the cover located on the right side of the projector, under the handle.

1. Attach the video-out cable supplied with your PowerBook to the video-out connector on the back of the PowerBook.

2. Attach the Macintosh VGA adapter to the VGA connector of the Y-cable.

3. Connect the VGA Macintosh adapter to the video-out cable.

4. Connect the Y-cable’s LCD connector to the projector’s Computer IN/OUT port.

5. Tighten the screws for all connectors to make sure they are fastened securely.

6. In the PowerBook’s Display Control Panel, select Mirroring.

Computer

Computer In/Out

Audio In

S-Video

10 1 • Installation

VGA

connector

LCD connector

monitor connector

+ 82 hidden pages