Assembly/ User Instructions
Assembly/ User Instructions
Incandescent Bulb Wall Fittings
Safety Warnings
Tools required:
Electrical Insulation Tape.
Minimum Distance: This is
Luminaires not suitable for direct mounting
INSTRUCTION MANUAL
Please read these instructions carefully before fitting your new light and retain for reference.
For Indoor use only
This pack contains:
1 x Light Fitting with Fixing Bracket, side screws
& washers or special backplate
Screws, wall plugs
Terminal Blocks as required by specific
instructions
Candle Tubes/ sconces as required
Drill & assorted drill bits
Safety glasses
Small electrical screw driver
Medium cross head screwdriver
Medium flat head screwdriver
Small Pliers with wire stripper
If in doubt we recommend you contact a qualified electrician. Before installing your light fitting always:
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker
before commencing installation.
Ensure that no one else has access that would enable the supply to be inadvertently reconnected.
This product is only suitable for connection to 240V~50Hz supply in accordance with Part P, UK Building Regulations
and current IEE Wiring Regulations and is not suitable for a Bathroom location.
The light fitting should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp miniature circuit
breaker).
If the Class II, Double Insulated symbol
and Live or Neutral must not be
The terminal blocks are supplied according to requirements of the fitting.
If any modification is made it will invalidate the warranty and may render the product unsafe.
This type of Light Fitting may be connected to a Dimmer but seek advice before purchase.
If there is a “Minimum Distance” Label, please do not allow Flammable Materials to rest within that distance from the
lamps.
the symbol which denotes
this requirement.
If the Light Fitting must not be mounted on combustible surfaces there will be the above symbol on it.
If there is no symbol then the Light Fitting may be mounted on any surface, including combustible ones.
1. Remove existing light fitting. Ensure there is a solid mounting, preferably a brick or block wall. If the wall is
timber frame and plasterboard construction then please use appropriate fixings for plasterboard or screw
directly into the timber frame. Ensure the fixing can support the weight of the wall light.
2. Refer to generic diagram; the fixing bracket must be screwed to the wall on a horizontal line, this view is from
above for clarity.
3. Unscrew the side screws (7) partially if their fixings are “L” slots or completely, if fixings are holes; retain
screws and washers. Remove the fixing bracket and use this as a template to mark the screw holes for your
chosen location.
connected to Earth. If there is no such symbol the Fitting must be Earthed.
is on the Light Fitting then the Fitting does not require an Earth
On normally flammable surfaces (surface
Mounted)
1
Assembly/ User Instructions continued
Care Information
Endon Lighting
LS9 0SE
20150309 GI 16v3
4. Fix the bracket in the location using the screws (2) and plugs (1) supplied.
5. Support your fitting and connect the house wiring according to the Terminal Block diagram. Ensure no strands
of wire escape the Terminal Block (6). When you are sure of the connections wrap the Terminal Block and
overlap the wiring both sides with 2 layers of insulation tape. Fixed Terminal Blocks with an Insulation plate
underneath them do not require further insulation.
6. Fix your fitting in position by reversing step 3 ensuring no wires are damaged, trapped or left exposed.
7. Slide the “Candle Tubes” over the lamp holders if appropriate for your fitting.
8. Install the Bulbs, do not install bulbs with a greater wattage or different shape than specified on the label.
Energy saving replacement bulbs run much cooler so larger equivalent light outputs may be used.
9. Some fittings may have “Strings” of beads and drops which must be attached after the actual installation of the
Light Fitting, please refer to the additional sheet if this is the case.
Generic Diagram Terminal Block (6) in Generic Diagram
All Light Fittings for UK Market are designed for 240V ac, 50 Hz (220-240V ac)
Please retain these instructions for future reference.
Switch off and allow 10 minutes to cool before cleaning, use only dry cloth.
2
Loading...