Emerson LK150, LK151 Owner's Manual
READ AND SAVE THESE INSTRUCTIONS
Ceiling Fan
Light Fixture
Owner’s Manual
Net Weight: 2.6 Lbs.
Includes: Three 60-Watt
Candelabra Bulbs and Fitter
Model Numbers:
LK150
LK151
Safety Instructions
WARNING: To avoid fire, shock, and serious personal injury, follow all instructions carefully.
1.Read your Owner's Manual carefully before installing the light fixture. Retain Owner's Manual for
future reference.
2.Be careful of the fan and blades when cleaning, painting, or working near the fan. Before installing
or servicing the light fixture or ceiling fan, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3.Do not exceed the wattage indicated on fixture.
ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION
1.To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker
box before wiring.
2.Make certain no bare wires are exposed outside the wire connectors.
3.All wiring must conform to national and local electrical codes.
4.Follow the recommended instructions for the proper method of wiring your new light fixture. If you
feel you do not have enough electrical wiring knowledge or experience, have your light fixture
installed by a licensed electrician. Any electrical work not described in this manual should be
performed by a licensed electrician.
WARNING: To reduce the risk of possible fire and electrical shock, install only on Emerson CF772
Series Ceiling Fans in indoor locations.
Part No. F40BP74420001 Form No. BP7442-1
Revision: 130402 ETL Model Nos.: LK150 and LK151
7. Insert the black and white wires through the lock-
washer and hex nut (supplied), firmly tighten the
hex nut to secure the light kit fitter to the switch
cup. Connect the white wire from the switch cup
to the white wire of the light fitter (Figure 2).
Connect the blue wire from the switch cup to the
black wire of the light fitter. Use listed wire conÂnectors (previously removed in Step 5) to make
connections (Figures 2 and 3).
8. Carefully tuck all wires and splices into the switch
cup. (Figure 2.)
9. Connect the motor connector to the switch cup
connector.
10. Position the cup/light fitter in the cover plate and
install the three screws that were previously
removed in Step 2 and tighten securely.
11. Install three 60-watt candelabra base bulbs
(supplied) into the light sockets.
2
Assembly and Installation
4. Remove the center screw from the switch cup
(Figure 1).
5. Carefully locate the white and blue wires (labeled
either "L" or "LIGHT") in the switch cup and
remove the wire connectors from the wires.
6. Insert the black and white wires from the light fitter
through the center hole in the switch cup
(Figure 2) and thread the switch cup onto the light
fitter. Hold wires taut while installing switch cup to
prevent the wires from twisting. Tighten the fitter
until the fan switch chain aligns with the hole in the
fitter.
Do not install or use the light fixture if any part
is missing or damaged. Contact your dealer for
replacement.
Figure 1
Installation on Emerson Fans
Having a Modular Switch Cup with
Center Screw
1. Remove all parts and parts packages from the
carton.
2. Remove the switch cup from the cover plate by
removing the three screws around the side of the
switch cup (Figure 1).
3. Disconnect the motor connector from the switch
cup connector (Figure 1).
WARNING
!
To avoid possible electrical shock, be sure
electricity is turned off at the main fuse or
circuit breaker box before wiring.
WARNING
!
Figure 2
Figure 3
WARNING: To avoid possible fire or electrical
shock, make certain no bare wire strands are
exposed outside wire connectors.
To avoid possible fire or electric shock, be careful
not to pinch wires between switch cup and the cover
plate.
WARNING
!
MOTOR
CONNECTOR
SCREWS
COVER PLATE
SWITCH CUP
CONNECTOR
MOTOR
CONNECTOR
BLACK WIRE
BLUE WIRE
HEX NUT
SCREWS
SWITCH CUP
RUBBER
WASHER
LIGHT
FITTER
RUBBER
WASHER
HEX NUT
BOWL CAP
(FN200)
COVER PLATE
SWITCH CUP
CONNECTOR
WIRE
CONNECTOR
WHITE WIRES
LOCKWASHER
FAN SWITCH
CHAIN
FAN SWITCH CHAIN
FINIAL (FN200)
SWITCH
CUP
CENTER SCREW
Loading...