Emerson LK130 Owner's Manual

8. Attach the cover/light fitter(5)(6) to the switch

assembly housing(1) using the two screws(2) that were removed in Step 2) (Figure 4.)

9. Proceed to “Installation of Glass Bowl”

section.

LIMITED WARRANTY

What The Warranty Covers:

All products covered by this Owner’s Manual are warranted against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered.

What The Period Of Coverage Is:

All components are covered by this warranty for one year from the date you purchased your light fixture. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.

What Will Emerson Electric Co. Do To Correct Problems: Emerson Electric Co. will replace a defective Emerson Light Fixture at no charge to you. WE WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL, REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON ELECTRIC CO.

How Can You Get Service:

YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE LIGHT FIXTURE TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized service center.

• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products, Division of Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers shown on the product with your request.

• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service center.

You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson Light Fixture should be properly packed to avoid damage in transit since we will not be responsible for any such damage.

What Is Not Covered:

This warranty also does not cover any defects, malfunctions or failures caused by:

• Repairs by persons not authorized by Emerson Electric Co.,

• Use of parts or accessories not authorized by Emerson Electric Co.,

• Mishandling, improper installation, modifications or damage to your light fixture while in your possession, or

• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.

Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:

• The original purchaser or user ceases to own the product, or

• The ceiling fan is moved from its original point of installation.

This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co. REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing other property which was damaged if this product does not work properly.

How State Law Relates To The Warranty:

Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Ceiling Fan Light Fixture Owner's Manual

Form No. F40BP74140000 Part No. BP7414

U.L. Model No.: LK130

READ AND SAVE THESE INSTRUCTIONS

Net Weight: 1.8 Lbs.

Suitable for Damp

Locations

Includes: Two 50-Watt Mini-Candelabra Base Halogen Bulbs

Trouble Shooting

TROUBLE PROBABLE CAUSE SUGGESTED REMEDY

1. Both Lamps Will 1. Wiring not complete. 1. Check all wiring connections to light kit. Not Illuminate.

2. Light bulbs do not light. 2. Check and replace light bulbs.

2. The 1.25A fuse may have blown. 3. Replace fuse.

Includes 3 finials and 3 outer bowl caps in the following finishes:

Oil Rubbed Bronze, Brushed Steel & Appliance White

Form No. BP7414

Part No. F40BP74140000

Printed in China 03/10

To avoid fire hazard, do not exceed wattage indicated on the fixture.

WARNING

Over lamping the light kit will result in the lamps being automatically shut off. Use only 50-watt maximum minicandelabra base halogen lamps. Turn off electricity before replacing the lamps.

WARNING

Air Comfort Products

DIVISION OF EMERSON ELECTRIC CO. 8100 W. Florissant • St. Louis, MO 63136

Figure 6

For repair parts, phone:

1-800-654-3545

4. Install the light switch chain through the

center of the finial nut(3). Screw the finial nut finger tight onto the fitters threaded nipple.

CAUTION

Be sure that the fan switch chain does not make contact with the light bulbs. If necessary reposition the light fitter to avoid the fan switch chain from touching the light bulbs.

5. Install pendants(2) onto light fixture chain

and fan switch chain.

NOTE: It is advisable to periodically check the tightness of the finial.

6. Installation is complete. Turn on electricity at

main fuse or circuit breaker box.

To avoid fire or electrical shock, be careful not to pinch wires between the switch housing assembly and the cover.

WARNING

Installation of Glass Bowl

1. Install two 50-watt (maximum) mini-

candelabra base halogen bulbs (included) into the fitter sockets.

2. Place the glass bowl(1) onto the light fitter

by inserting the threaded nipple through the bottom hole of the bowl.

3. Where applicable, insert the fan speed

control switch chain through the offset hole in the bowl cap, glass bowl and then the offset hole in the outer bowl cap.

Model Number:

LK130

FITTER SOCKET (2)

BOWL CAP

THREADED NIPPLE

LIGHT FITTER

OUTER BOWL CAP

(3) FINIAL

LIGHT SWITCH CHAIN

PENDANTS (2)

FAN SPEED CONTROL SWTICH CHAIN (WHERE APPLICABLE)

FAN SWITCH CHAIN

50-WATT MINI-CANDELABRA BASE HALOGEN BULBS (2)

(1) GLASS BOWL

Parts Included: 1 Glass Bowl, 1 Light Fitter, 3 Outer Bowl Caps, 3 Finial Nuts, 2 50-Watt Mini-Candelabra Base Halogen Bulbs, 2 Wire Connectors, 2 Pendants, 1 Lockwasher, 1 Hex Nut and 2 Pull Chains.

7. Insert the black and white wires through the

lockwasher(8) and hex nut(9) supplied. Firmly tighten the hex nut to secure the light kit fitter to the switch cup.

8. Connect the white wire from the switch cup to

the white wire of the light fitter (Figure 2). Connect the blue wire from the switch cup to the black wire of the light fitter. Use the wire connectors provided with the light kit to make the electrical connections (Figures 2 and 3).

9. Carefully tuck all wires and splices into the

switch cup(1). (Figure 2.)

10. Connect the motor connector(4) to the

switch cup connector(5).

11. Position the switch cup(1) and fitter

assembly(7) on the cover plate(2) and install the three screws(3) that were previously removed in Step 2 and tighten securely.

12. Proceed to “Installation of Glass Bowl”

section.

WARNING

Assembly and Installation

4. Remove the center screw(6) from the switch

cup (Figure 1).

5. Carefully locate the white and blue wires

(labeled either "L" or "LIGHT") in the switch cup and remove the wire connectors from the wires.

6. Insert the black and white wires from the

light fitter(7) through the center hole in the switch cup (Figure 2) and thread the switch cup onto the light fitter. Hold wires taut while installing switch cup to prevent the wires from twisting.

Do not install or use the light fixture if any part is missing or damaged. Call toll-free:

1-800-654-3545

To avoid possible electrical shock, be sure electricity is turned off at the main fuse or circuit breaker box before wiring.

Figure 1

Installation on Emerson Fans

Having a Modular Switch Cup

with Center Screw

1. Remove all parts and parts packages from

the carton.

2. Remove the switch cup(1) from the cover

plate(2) by removing the three screws(3) around the side of the switch cup (Figure 1).

WARNING

3. Disconnect the motor connector(4) from the

switch cup connector(5) (Figure 1).

Figure 2

To avoid possible fire or electric shock, be careful not to pinch wires between switch cup and the cover plate.

WARNING

Installation on Emerson Fans

Having Two-Piece Die-Cast

Switch Housings

1. Remove all parts and parts packages from

carton.

2. Remove the cover(5) from the fan switch

housing(1) by removing the two outer screws(2). (See Figure 4).

3. Remove the center screw(4) from the

cover(5). Insert the black and white wires from the light kit fitter(6) through the hole and thread the switch housing cover tightly onto the light kit fitter.

4. Insert the black and white wires through the

lockwasher(8) and hex nut(9) supplied. Firmly tighten the hex nut to secure the light kit fitter to the switch housing cover(5).

5. Carefully locate the white and blue wires

(labeled either “L” or “LIGHT”) in the switch housing and remove the wire connectors(3) from the wires.

6. Connect the white wire from the ceiling fan

to the white wire of the light kit fitter(6). Connect the blue wire from the ceiling fan to the black wire of the light kit fitter. Use the wire connectors provided with the light kit to make the electrical connections (Figures 4 and 5.)

7. Carefully tuck all wires and splices into the

switch housing(1).

8. Attach the cover/light fitter(5)(6) to the switch

Figure 4

Figure 5

To avoid possible fire or electrical shock, make certain no bare wire strands are exposed outside wire connectors.

WARNING

Figure 3

To avoid possible fire or electrical shock, make certain no bare wire strands are exposed outside wire connectors.

WARNING

Safety Instructions

To avoid fire, shock, and serious personal injury, follow all instructions carefully.

1. Read your Owner's Manual carefully before installing the light fixture. Retain Owner's Manual for future reference.

2. Be careful of the fan and blades when cleaning, painting, or working near the fan. Before installing or servicing the light fixture or ceiling fan, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel.

3. Do not exceed the wattage indicated on fixture (Two 50-watt mini-candelabra base halogen bulbs).

ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION

1. To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker box before wiring.

2. The installation is to be in accordance with the National Electrical Code, ANSI/NFPA 70-2008 and Local Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician.

3. Make certain no bare wires are exposed outside the wire connectors.

4. All wiring must conform to national and local electrical codes.

5. Follow the recommended instructions for the proper method of wiring your new light fixture. If you feel you do not have enough electrical wiring knowledge or experience, have your light fixture installed by a licensed electrician. Any electrical work not described in this manual should be performed by a licensed electrician.

WARNING: To reduce the risk of possible fire and electrical shock, install only on Emerson Model CF130.

(4) MOTOR CONNECTOR

(3) SCREWS

(5) SWITCH CUP CONNECTOR

(1) SWITCH CUP

(6) CENTER SCREW

(2) COVER PLATE

(4) MOTOR CONNECTOR

BLACK WIRE

BLUE WIRE

(9) HEX NUT

(3) SCREWS

(1) SWITCH CUP

OUTER BOWL CAP

(2) COVER PLATE

(5) SWITCH CUP CONNECTOR

(6) WIRE CONNECTOR

WHITE WIRES

(8) LOCKWASHER

FAN SWITCH CHAIN

(7) LIGHT FITTER

BOWL CAP

FAN SWITCH CHAIN (WHERE APPLICABLE)

FAN SWITCH CHAIN

BLUE WIRE

BLACK WIRE

(5) COVER

(2) SCREWS

(1) SWITCH HOUSING ASSEMBLY

WHITE WIRE

(9) HEX NUT (8) LOCKWASHER

(6) LIGHT FITTER

(7) BOWL CAP

(3) WIRE CONNECTORS

(4) CENTER SCREW