Page 1
READ AND SAVE THESE INSTRUCTIONS
“Derby” Series
Model No.
F2100AB02
F2100BS02
F2100PB02
F2100WW02
“Amphora” Series
Model No.
F2200HTW02
F2200S02
F2200TG02
F2200OB02
Derby & Amphora Series
Ceiling Fan Owner's Manual
Part No. F40BP71880005 Form No. BP7188-5
Net Weight: 21.7 Lbs.Net Weight: 21.5 Lbs.
®
Page 2
TABLE OF CONTENTS
Page
Rules for Safe Use & Installation ……………………………………………………………………………………………2
Tools Needed for Assembly …………………………………………………………………………………………………3
Unpacking Instructions ………………………………………………………………………………………………………3
Assembly Instructions…………………………………………………………………………………………………………4
Electrical Requirements ………………………………………………………………………………………………………5
How to Hang Your Ceiling Fan ………………………………………………………………………………………………5
How to Wire Your Ceiling Fan ………………………………………………………………………………………………6
Using Your Ceiling Fan ………………………………………………………………………………………………………7
Attaching Light Kit ……………………………………………………………………………………………………………7
Maintenance……………………………………………………………………………………………………………………7
Trouble Shooting ………………………………………………………………………………………………………………8
Repair Parts ………………………………………………………………………………………………………………9-10
Warranty ………………………………………………………………………………………………………………………12
2
WARNING
!
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must satisfy National and Local Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be grounded as a precaution against possible
electrical shock. Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably supporting at least 50
pounds. Use only U.L. outlet boxes listed as acceptable for fan support, and use the mounting
screws provided with the outlet box. Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
4. The downrod furnished with the fan provides the minimum recommended floor to fan blade
clearance for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with the fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do
not know enough about electrical wiring, have your fan installed by a licensed electrician.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not
specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use with this product by Emerson. Substitution of parts or
accessories not designated for use with this product by Emerson could result in personal injury or
property damage.
WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
Page 3
1. Open styrofoam unit containing fan. Remove top
half of styrofoam unit. Remove parts and check to
see that you have received the following:
a. Fan motor and housing assembly
b. One motor cover
c. One ceiling cover
d. Five blade flanges
e. One hanger ball/downrod assembly
f. One hanger bracket
g. One switch housing cover
h. One finial (Amphora only)
i. One loose parts bag containing:
1. One setscrew
2. One 5/32" hex wrench
3. Eleven 10-32 x 5/8" oval head screws
4. Two 1” threaded studs
5. Two 1-1/4” threaded studs
6. Four knurled knobs
7. Three wire connectors
8. Two screws 8-32 x 3/8" (Derby only)
9. Two pull chain pendants, and couplings
10. One hairpin clip
11. One clevis pin
12. Two lockwashers
13. Sixteen 10-32 x 3/8" pan head screws
14. Sixteen flat washers
15. 1/8-27 x 1-1/2” Threaded nipple
(Amphora only)
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One Phillips head screwdriver One stepladder
Three wire connectors (supplied.) One wire stripper
MATERIALS
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of the following
size:
3
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is
completed, place a check mark in the box. This will insure that all steps have been
completed and will be helpful in finding your place should you be interrupted.
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
NOTE: Place the parts from the loose parts bags
in small containers to keep them from being lost.
If any parts are missing, contact your local retailer or catalog outlet for replacement before proceeding.
NOTE: Fan blades are ordered separately and are
packaged in separate carton.
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (see page 6). If you
feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson. Substitution of parts or accessories not
designated for use with this product by Emerson
could result in personal injury or property damage.
WARNING
!
WARNING
!
SWITCH
HOUSING
COVER
CEILING
COVER
FOAM
PACKING
PROTECTIVE
PLASTIC BAG
FOAM
PACKING
BLADE
FLANGES
LOOSE
PARTS BAG
HANGER
BRACKET
MOTOR AND
HOUSING ASSEMBLY
HANGER BALL/
DOWNROD
ASSEMBLY
MOTOR
COVER
CARTON
Page 4
4
1. Remove the fan motor and housing assembly from
styrofoam packaging and position it so that the top
of the motor is facing you.
2. Separate, untwist and unkink the three motor
leads. Route the motor leads through the hanger
ball/downrod assembly and seat the downrod in the
motor coupling.
3. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip. The clevis pin
must go through the holes in the motor coupling
and the holes in the downrod. Push the straight leg
of the hairpin clip through the hole near the end of
the clevis pin until the curved portion of the hairpin
clip snaps around the clevis pin. The hairpin clip
must be properly installed to prevent the clevis pin
from working loose. Pull on the hanger ball to make
sure the clevis pin is properly installed.
4. Install the setscrew (supplied in loose parts bag) in
the motor coupling. While pulling up on the hanger
ball, tighten the setscrew using the 5/32" setscrew
wrench (supplied).
NOTE: The setscrew must e properly installed as
described above, or fan wobble could result.
5.Remove the hanger ball by loosening the setscrew
in the hanger ball until the ball falls freely down the
downrod. Remove the pin from the downrod, then
remove the hanger ball. Retain the pin and hanger
ball for reinstallation in step 8.
6.Screw two 1” threaded studs (provided) into the
motor. Leave approximately 7/8” of the stud
extending above motor. Slide the motor cover over
the downrod and rotate the cover until the threaded
studs protrude; install two knurled knobs (supplied)
to secure the cover.
NOTE: Make sure the red and brown leads are
capped with wire connectors and are completely
inside motor cover and not pinched between the
motor cover and motor.
7.Position the ceiling cover over the downrod. Be sure
the cover is oriented correctly, with the large
opening at the top.
8.Reinstall the hanger ball on the downrod as follows.
Route the motor leads through the hanger ball and
slide the hanger ball over the downrod. Install the pin
through the holes at the top of the downrod and slide
the hanger ball up the downrod, aligning the ball so
the pin is captured in the groove in the top of the
hanger ball. Pull the hanger ball up tight against the
pin and securely tighten the setscrew in the hanger
ball. A loose setscrew could create fan wobble.
Assembly Instructions
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!
HANGER BALL
DOWNROD
HAIRPIN
SETSCREW
CLEVIS PIN
HAIRPIN
CLIP
CLEVIS
PIN
CLIP
MOTOR
COUPLING
HANGER BALL/
DOWNROD
ASSEMBLY
CLEVIS
PIN
MOTOR COUPLING
PIN
HANGER BALL
DOWNROD
SETSCREW
KNURLED
KNOB
MOTOR
COVER
WIRE
CONNECTORS
1" THREADED
RED LEAD
BROWN LEAD
7/8"
STUD
MOTOR
SETSCREW
DOWNROD
WRENCH
PIN
HANGER BALL
DOWNROD
CEILING COVER
SETSCREW
Page 5
5
9. The fan comes with blue, black and white leads
that are 80” long. Before installing fan, measure up
approximately 6 to 9-inches above the ball/
downrod assembly. Cut off excess leads and strip
back insulation 1/2-inch from end of leads.
10.Use three 10-32 x 3/8" pan head screws and flat
washers (supplied) to secure flange to blade, as
shown below. Repeat for the remaining four
blades.
11.Use the 10 round recessed holes in the motor hub
marked with "5" and install the five blade assemblies
(ordered separately) in accordance with Step 8.
12.Attach one blade assembly to the motor hub using
two 10-32 x 5/8" oval head screws (supplied). Do
not tighten completely at this time. Install remaining blade assemblies in the same way. Gently
snug all flange screws to the motor hub, working
around the hub in a clockwise sequence. Next,
securely tighten all flange screws, again working in
a clockwise sequence. Failure to follow this procedure could result in fan wobble. This completes
the blade installation.
Electrical Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50 pounds.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
How to Hang Your
Ceiling Fan
Figure 1
To reduce the risk of personal injury, do not bend the
blade flanges when installing the blades or cleaning
the fan. Do not insert foreign objects between
rotating fan blades.
WARNING
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support, and use screws supplied with outlet
box. Most outlet boxes commonly used for support
of light fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified
electrician if in doubt.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 1).
WARNING
!
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 lbs.
WARNING
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support, and use screws supplied with outlet
box. Most outlet boxes commonly used for support
of light fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified
electrician in in doubt.
WARNING
!
BLADE
FLANGE
BLADE
FLAT WASHER (3)
10-32 x 3/8" PAN HEAD
SCREW (3)
MOTOR
HUB
CEILING
AT LEAST
7'
10-32 x 5/8"
OVAL HEAD SCREWS
(2 PER BLADE
ASSEMBLY)
FLOOR
Page 6
6
1. Securely attach the hanger bracket to the outlet
box using the two screws supplied with the outlet
box. (Figure 2).
2. Carefully lift the fan and seat the hanger ball/
downrod assembly on the hanger bracket that was
just attached to the outlet box (Figure 3). Be sure
the groove in the ball is lined up with tab on the
hanger bracket (Figure 2).
How to Wire Your
Ceiling Fan
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
1. Connect the green grounding lead from the hanger
ball and the green grounding lead from the hanger
bracket to the grounding conductor of supply (this
may be a bare wire or wire with green colored insulation). Securely connect wires with wire connector
supplied.
NOTE: If you are using an Emerson Light Fixture
with your fan, see Light Fixture Owner’s Manual
for wiring.
2. Securely connect the fan motor white wire to the
supply white (neutral) wire using wire connector
supplied (Figure 4). Securely connect the fan motor
black wire and blue wire to the supply black (hot)
wire using wire connector supplied (Figure 4). After
connections have been made, turn leads upward
and carefully push leads into the outlet box, with
the white and green leads on one side of the outlet
box and the black and blue leads on the other side
of the outlet box.
Figure 2
Figure 3
Figure 4
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
WARNING
!
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
!
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
!
To avoid possible fire or shock, be sure that
electricity is turned off at the main fuse box before
wiring.
NOTE: If you are not sure if the outlet box is
grounded, contact a licensed electrician for advice,
as it must be grounded for safe operation.
WARNING
!
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
WARNING
!
OUTLET
BOX
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
TAB
HANGER
BRACKET
NOTE: CEILING COVER,
SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD ASSEMBLY
BLACK AND BLUE
GROUND
WIRE
LISTED
WIRE
CONNECTOR (3)
GREEN WIRE
(GROUND) FROM
HANGER BRACKET
GREEN WIRE
(GROUND) FROM
HANGER BALL
FAN WIRES
WHITE SUPPLY
(NEUTRAL)
WHITE FAN
WIRE
BLACK SUPPLY
(HOT)
NOTE: CEILING COVER
OMITTED FOR CLARITY.
Page 7
Using Your Ceiling Fan
1. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box.
2. Check the operation of the fan by gently pulling on
the 4-position speed control pull chain switch. (This
switch has the longer pull chain.) The operating
sequence is as follows:
THREE-SPEED
1st Pull—HIGH
2nd Pull—Medium
3rd Pull—Low
4th Pull—OFF
3. If airflow is desired in opposite direction, turn your
fan off and wait for the blades to stop turning. Then
pull the shorter switch chain and turn fan on again.
The fan blades will turn in the opposite direction
and reverse the airflow.
Attaching Light Kit
To install an accessory light kit, remove the two
screws securing the switch housing cover to the
switch housing. Remove the screw plug from the bottom of the switch housing cover and install the light kit
in accordance with the light kit Owner's Manual. On
Amphora Models only, the decorative switch housing
cover and threaded nipple will have to be removed
first before performing this procedure.
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
3. Screw the two 1-1/4” threaded studs (provided) into
the tapped holes in the hanger bracket.
4. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 5).
5. Secure the ceiling cover in place by sliding lockwashers over the threaded studs and installing the two
knurled knobs (supplied). (Figure 5.) Tighten the
knurled knobs securely until the ceiling cover fits
snugly against the ceiling and the hole in the ceiling
cover is clear of the downrod. Your fan is now wired
to be turned on and off from the fan switch.
6. (Derby only). Slip the two pull chains through the
bushings in the switch housing cover. Position the
switch housing cover on the switch housing and
secure using two 8-32 x 3/8” screws (supplied).
Secure the smaller pendant to the shorter chain
and the larger pendant to the longer chain.
7. (Amphora only). Thread the 1/8-27 x 1-1/2” nipple
(supplied) into the switch housing. Slip the two
chains through the bushings in the switch housing
cover. Position the switch housing cover on the
threaded nipple and secure to the switch housing
using the finial (supplied). When assembled the
bushings on the decorative switch housing cover
must align with the switches for easy operation.
G
7
SPEED
CONTROL
SWITCH
REVERSING
SWITCH
Figure 5
Figure 6
Figure 7
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
WARNING
!
To avoid possible electrical shock, be sure electricity
is turned off at the main service box before wiring.
WARNING
!
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
WARNING
!
CEILING COVER
1-1/4"
THREADED
STUD
KNURLED KNOB
LOCKWASHERS (2)
8-32 x 3/8"
SCREW (2)
SWITCH
HOUSING
DECORATIVE SWITCH
HOUSING COVER
BUSHING
PENDANT
SWITCH HOUSIN
COVER
SWITCH
HOUSING
COVER
1/8-27 x 1-1/2"
THREADED NIPPLE
FINIAL
Page 8
Trouble Shooting
TROUBLE PROBABLE CAUSE SUGGESTED REMEDY
1. Fan will not start. 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit
breakers.
WARNING: Make sure main power is turned off.
2. Loose power line connections to the fan, or loose 2. Check line wire connections to fan and switch
switch wire connections in the switch housing. wire connections in the switch housing.
2. Fan sounds noisy. 1. Blades not attached to fan. 1. Attach blades to fan before operating.
2. Loose screws in motor housing. 2. Check to make sure all screws in motor housing
are snug (not over-tight).
3. Screws securing fan blade flanges to motor hub 3. Check to make sure the screws which attach
are loose. the fan flanges to the motor hub are tight.
WARNING: Make sure main power is turned off.
4. Wire connectors inside switch housing rattling. 4. Check to make sure wire connectors in
switch housing are not rattling against each
other or against the interior wall of the switch
housing.
5 Screws holding blades to flanges are loose. 5. Tighten screws securely.
3. Fan wobbles 1. Setscrew in motor coupling is loose. 1. Raise motor cover and tighten setscrew securely.
excessively.
2. Setscrew in hanger ball/downrod assembly is 2. Tighten the setscrew in the hanger ball/downrod
loose. assembly.
3. Screws securing fan blade flanges to motor are 3. Check to be sure screws which attach the fan blade
loose. flanges to the motor are tight.
4. Fan blade flanges not seated properly. 4. Check to be sure the fan blade flanges seat firmly and
uniformly to the surface of the motor hub. If flanges are
seated incorrectly, loosen the flange screws and
retighten according to step 8 in the section “Assembly
Instructions”.
5. Hanger bracket and/or ceiling outlet box is not 5. Tighten the hanger bracket screws to the outlet box,
securely fastened. and/or secure outlet box.
6. Fan blades out of balance. 6. Interchanging an adjacent (side-by-side) blade pair can
redistribute the weight and result in smoother operation.
Or use supplied balancing kit to balance blades.
8
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER
BEFORE TROUBLE SHOOTING YOUR FAN.
!
!
!
Page 9
15
Repair Parts
ACCESSORIES
1. Ceiling Fan Light Kits (see store or catalog).
2. Downrod Extension Kits (see store or catalog).
3. Ceiling Fan Controls (see store or catalog).
Before discarding packaging material, be certain all parts have
been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
• PART NUMBER
• PART DESCRIPTION
• NAME OF ITEM
• MODEL NUMBER
For repair parts, phone 1-800-654-3545.
9
WARNING
THIS PRODUCT IS DESIGNED TO USE ONLY THOSE
PARTS SUPPLIED WITH THIS PRODUCT AND/OR
ANY ACCESSORIES DESIGNATED SPECIFICALLY
FOR USE WITH THIS PRODUCT BY EMERSON ELECTRIC. SUBSTITUTION OF PARTS OR ACCESSORIES
NOT DESIGNATED FOR USE WITH THIS PRODUCT
BY EMERSON ELECTRIC COULD RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE.
WARNING
THE USE OF ANY OTHER CONTROL NOT SPECIFICALLY APPROVED FOR THIS FAN COULD RESULT
IN FIRE, SHOCK, AND PERSONAL INJURY.
14
17
18
2
1
3
16
6
18
13
33
30
5
34
4
32
21
22
23
7
8
26
27
AMPHORA SERIES ONLY
9
19
10
10
31
24
11
20
12
11
12
31
25
24
28
29
Page 10
10
Repair Parts List
Derby Models Amphora Models
Ref.
No. Description
F2100PB02 F2100WW02 F2100AB02 F2100BS02 F2200HTW02 F2200TG02 F2200S02 F2200OB02
Hanger Pack, 761655-2 761655 761655-3 761655-17 761655-12 761655-13 761655-16 761655-9
containing:
1 Bracket, Hanger (1) — — — — — — — —
2 Hanger Ball Assembly (1) — — — — — — — —
3 Downrod (1) — — — — — — — —
6 Cover, Ceiling 761620-2 761620 761620-3 761620-25 761620-12 761620-23 761620-24 761620-9
7 Hub, Rubber 760601 760601 760601 760601 760601 760601 760601 760601
8 Blade Assembly * * * * * * * *
(Full set for one fan)
9 Flange Set 761520 761520-1 761520-2 761520-4 761521-1 761521-4 761521-5 761521-6
(Full set for one fan)
10 Switch Cup 761506-2 761506-3 761506-7 761506-11 761506-8 761506-9 761506-10 761506-9
13 Cover, Motor 761621-2 761621 761621-3 761621-15 761621-12 761621-13 761621-16 761621-9
23 Motor 762304 762304 762304 762304 762304 762304 762304 762304
Parts Bag, containing: 761629 761629 761629-1 761629-2 761629 761629-1 761629-1 761629-1
4 Pin, Clevis (1) — — — — — — — —
5 Clip, Hairpin (1) — — — — — — — —
11 Coupling (2) — — — — — — — —
12 Pendant (2) — — — — — — — —
14 Wire Connector (3) — — — — — — — —
15 Wrench, Setscrew (1) — — — — — — — —
16 Stud, Threaded 1-1/4” (2) — — — — — — — —
17 Lockwasher (2) — — — — — — — —
18 Knob, Knurled (4) — — — — — — — —
19 Screw, 10-32 x 5/8" (11) — — — — — — — —
20 Screw, 8-32 x 3/8" (2) — — — — — — — —
21 Screw, 10-32 x 3/8" (16) — — — — — — — —
22 Washer, Flat (16) — — — — — — — —
28 Nipple, Pipe — — — — — — — —
32 Setscrew, 7/16-18 x 1/4" (1) — — — — — — — —
34 Stud, Threaded, 1” (2) — — — — — — — —
24 Cover, Switch Housing Assembly 761515 761515-1 761515-2 761515-4 761516-1 761516-4 761516-5 761516-6
25 Cover, Housing — — — — 760671-14 760671-16 760671-17 760671-15
26 Washer, 9/16” — — — — — — — —
27 Lockwasher, 9/16” — — — — — — — —
29 Nut, Finial — — — — 761508-1 761508-4 761508-17 761508-16
30 Aux. Capacitor 761453 761453 761453 761453 761453 761453 761453 761453
31 Harness 761505 761505 761505-1 761505-2 761505 761505-1 761505 761505-1
33 Screw, #8 Washerhead 8-32 x 3/8” (4) — — — — — — — —
— Owner's Manual BP7188-5 BP7188-5 BP7188-5 BP7188-4 BP7188-5 BP7188-5 BP7188-5 BP7188-5
Page 11
11
NOTES
Page 12
Printed in Taiwan 04/03
Part No. F40BP71880005 Form No BP7188-5
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in
workmanship and materials. You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for the lifetime of your ceiling fan. All other components and accessories are
covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND
ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Company Do To Correct Problems:
Emerson will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to
you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can be provided,
Emerson will refund the actual purchase price of your fan. WE WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO
YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL, REINSTALLATION AND SHIPPING OF
THE PRODUCT TO EMERSON.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR
RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest
authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to
Air Comfort Products, Division of Emerson Company, 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model
numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service
center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service
center. Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be
responsible for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any
defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Company,
• Use of parts or accessories not authorized by Emerson Company,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral
warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson
Company.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND
EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL
DAMAGES. Incidental damages include but are not limited to such damages as loss of time and loss of use. Consequential
damages include but are not limited to the cost of repairing or replacing other property which was
damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Air Comfort Products
DIVISION OF EMERSON COMPANY
8100 W. Florissant ¥ St. Louis, MO 63136
Loading...