Emerson 4390 Data Sheet

Product Data Sheet
00813-0100-4393, Rev AB
Rosemount™ 4390 Series of Corrosion and Erosion Wireless Transmitters
March 2021
Rosemount 4390 Series of Corrosion and Erosion Wireless Transmitters provide continuous, accurate, and highly sensitive real-time corrosion and erosion monitoring data, enabling maximum performance through process optimization and eliminate the need of costly walkdowns. The transmitter contributes to superior corrosion and erosion management data by using top-range technology to provide improved data processing, flexible data management solutions, and a friendly user interface.
The Rosemount 4390 Series of Corrosion and Erosion Wireless Transmitters have the following features:
Delivers best in class resolution and measurement sensitivity
Operates with Electrical Resistance (ER), Linear Polarization Resistance (LPR), Galvanic, Multiple-Element Sand/Erosion, or Combined probes
Reads monitoring probes from most common vendors
Provides up to 20 meters of probe cable that offer flexible, convenient positioning for maintenance and radio signals
Provides flexibility in data formats and data management
Rosemount 4390 Series Transmitters
March 2021

Operating principle

Rosemount 4390 Series of Corrosion and Erosion Wireless Transmitters is an Emerson™ wireless product and uses the same radio and power modules as other Emerson wireless products. The corrosion and erosion transmitter communicates through standard wireless Gateways. The gateways interface with existing host systems using industry standard protocols including OPC, Modbus TCP/IP, and Modbus RTU.
®
A. AMS Suite B. Plantweb™ Insight Inline Corrosion Application C. Modbus/OPC
D. HART® data

Reliable wireless architecture

Standard IEEE 802.15.4 radios
2.4 GHz ISM band sliced into 15 radio-channels
Allows for time-synchronized channel hopping in order to avoid interference from other radios, Wi-Fi®, and EMC sources, thereby increasing reliability
Delivers high reliability in challenging radio environments using Direct Sequence Spread Spectrum (DSSS) technology

High accuracy data monitoring

The transmitter can provide fast and reliable corrosion monitoring, identifying within 10 to 20 nanometers of metal loss, based on frequent measurements when using an ER probe.
2 www.emerson.com
March 2021
Rosemount 4390 Series Transmitters

System flexibility

The wireless transmitter allows up to a 20 meter cable between probe and transmitter — The transmitter can be installed conveniently for battery replacement and other maintenance without a need for
scaffolding for access
— The transmitter should be installed where it is most beneficial for wireless signal routing, avoiding shadows where radio
communication would be difficult
Reads corrosion and erosion probes from most common manufacturers

Data Management

Data format (calculated metal loss data, corrosion and erosion rates, or probe raw data) is user selectable from the HART terminal, or from the Emerson Asset Management System (AMS)
The corrosion wireless transmitter can be seamlessly integrated with Plantweb Insight Inline Corrosion Application and Fieldwatch™ software suite
Calculated metal loss can be transmitted directly to and displayed in Emerson AMS system
Calculated metal loss can be transmitted to any historian or control system for data management

Other benefits

The integrated Emerson wireless product, can be combined with other Emerson wireless products in an integrated network, using same gateway for data communication
Rosemount 4390 Series Transmitters 3
Rosemount 4390 Series Transmitters

Product specifications

Item Description
General For connection with intrusive corrosion and erosion probes
Connection Connected to a probe through a probe cable (maximum 65 ft (20 m))
Humidity limits 5 - 95% relative humidity
March 2021
Measurement intervals
Communication WirelessHart® 2.4 GHz DSSS (Discrete Sequential Spread Spectrum)
Instrument resolution
ER probe Actual accuracy 10-100 ppm of probe element thickness, depending on probe type and environmental
LPR probe Accuracy of 100 ppm for the resistance measured on the LPR port
Sand probe Actual accuracy 10-100 ppm of probe element thickness, depending on probe type and environmental
Operating pressure -40 °F (-40 °C) to 158 °F (70 °C)
Battery capacity To simulate the power module life span, refer to the calculator here:
Power module Black power module, type 701PBKKF; Replaceable, non-rechargeable; Intrinsically safe Lithium-Thionyl
Housing Painted aluminum, IP 66
Weight Painted aluminum: 5kg
Sand, Electrical Resistance (ER) and galvanic probes can be measured as fast as 1-minute intervals, while Linear Polarization Resistance (LPR) probes can be measured as fast as 4-minute intervals
24 bit
conditions
conditions
Power Module Life Estimator.
Chloride power module pack with PBT/PC enclosure. 7.2 V

Certification

Europe

Telecommunications compliance

All wireless devices require certification to ensure they adhere to regulations regarding the use of the RF spectrum. Nearly every country requires this type of product certification. Emerson is working with governmental agencies around the world to supply fully compliant products and remove the risk of violating country directives or laws governing wireless device usage.
4 www.emerson.com
March 2021 Rosemount 4390 Series Transmitters

Ex approvals for hazardous areas

Intrinsically safe parameters

Table 1: Intrinsically safe parameters
ER port Uo = 5.9V; Io = 1.697A; Po = 0.83W;
IIC: Co = 82nF; Lo = 12.34μH; Lo/Ro = 14.20 μH/Ω IIB: Co = 9uF; Lo = 49.36μH; Lo/Ro = 56.80 μH/Ω
LPR port Uo = 5.9V; Io = 0.235A; Po = 0.309W;
IIC: Co = 210nF; Lo = 0.64mH; Lo/Ro = 102 μH/Ω IIB: Co = 9uF; Lo = 2.56mH; Lo/Ro = 408 μH/Ω
Galvanic port Uo = 5.9V; Io = 0,180 A; Po = 0.244 W;
IIC: Co = 230nF; Lo = 1.09mH; Lo/Ro = 133 μH/Ω IIB: Co = 9uF; Lo = 4.36mH; Lo/Ro = 532 μH/Ω
HART service port Uo = 5.9V; Io = 12.64mA; Po = 18.65mW;
Co = 420nF; Lo = 223mH; Lo/Ro = 1.9mH/Ω; Ui = 1.9V; Ii = 32μA; Pi = 61μW; Ci = 1μF; Li = Negligible
Note
The transmitter can only be powered with 701PBKKF SmartPower Black Power Module with P/N 00753-9920-0001 only.
The whole electronics are isolated from the enclosure (boards, battery, antenna, etc.). It should withstand a 500V test between the metal body and circuits.
T amb = -40 °F (-40 °C) to 158 °F (70 °C)

I1 - ATEX Intrinsic Safety

Table 2: I1 - ATEX Intrinsic Safety
Certificate Presafe 20 ATEX 79679X
Standards EN IEC 60079-0:2018 and EN 60079-11:2012
Markings II 1 G Ex ia IIC T4 Ga, -40°C ≤ Ta ≤ 70°C
Specific conditions for safe use (X): - The external connections must be connected to intrinsically safe circuits
with parameters complying with the parameters specified in this certificate and the manufacturer’s installation manual.
- This product 4390 Series Corrosion and Erosion Wireless transmitters is approved with following battery pack model 701PBKKF SmartPower Module - Black with P/N 00753-9920-0001.
- The plastic enclosure of the battery pack model mentioned above may constitute a potential electrostatic ignition risk and caution should be used when being handled.
- The plastic antenna and the painted enclosure may present a potential electrostatic ignition hazard and must not be rubbed or cleaned with a dry cloth.
- Instrument enclosure made of 100% aluminum is used, impact and friction must be avoided due to ignition hazard.
- The probe outputs only connected to simple apparatus (passive circuits). All other terminals will only be connected to IS rated apparatus complying with the IS input parameters.
- Separate IECEx / ATEX certified IP66 cable gland or plugs must be used.
Rosemount 4390 Series Transmitters 5
Rosemount 4390 Series Transmitters March 2021

I7 - IECEx Intrinsic Safety

Table 3: I7 - IECEx Intrinsic Safety
Certificate IECEx PRE 20.0096X
Standards IEC 60079-0:2017 Edition 7.0
and IEC 60079-11: 2011 Edition 6.0
Markings Ex ia IIC T4 Ga, -40°C ≤ Ta ≤ 70°C
Specific conditions for safe use (X): - The external connections must be connected to intrinsically safe circuits
with parameters complying with the parameters specified in this certificate and the manufacturer’s installation manual.
- This product 4390 Series Corrosion and Erosion Wireless transmitters is approved with following battery pack model 701PBKKF SmartPower Module - Black with P/N 00753-9920-0001.
- The plastic enclosure of the battery pack model mentioned above may constitute a potential electrostatic ignition risk and caution should be used when being handled.
- The plastic antenna and the painted enclosure may present a potential electrostatic ignition hazard and must not be rubbed or cleaned with a dry cloth.
- Instrument enclosure made of 100% aluminum is used, impact and friction must be avoided due to ignition hazard.
- The probe outputs only connected to simple apparatus (passive circuits). All other terminals will only be connected to IS rated apparatus complying with the IS input parameters.
- Separate IECEx / ATEX certified IP66 cable gland or plugs must be used.
6 www.emerson.com
March 2021

Transmitter dimensions

Figure 1: Dimensions for the Rosemount 4390 Transmitter
Rosemount 4390 Series Transmitters
A. Probe cable gland (optional) B. Grounding lug C. 2.4 GHz external antenna
D. Power module extended cover
E. Electronics cover
F. 2.4 GHz extended range, external antenna G. Mounting bracket kit H. Junction box for probe connection
Rosemount 4390 Series Transmitters 7
XXX X XXX X X XX XXX XXX XX
1 2
Rosemount 4390 Series Transmitters March 2021

Rosemount 4390 Series of Corrosion and Erosion Wireless Transmitters ordering information

Specifications and options

See the Specifications and options section for more details on each configuration. Specification and selection of product materials, options, or components must be made by the purchaser of the equipment. See the Material selection section for more information.

Model codes

Model codes contain the details related to each product. Exact model codes will vary; an example of a typical model code is shown just below.
Mode code example
1. Required model components (choices available on most)
2. Additional options (variety of features and functions that may be added to products)

Product description

Code
439 4390 Series Wireless Corrosion and Erosion Transmitter
Product Description

Measurement

Code
1 Corrosion
2 Erosion
Description

Probe connection / mounting

Code
R Remote mounting with probe cable, bracket for wall or pipe mounting, and hardware for 2 in pipe mount
Description

Enclosure material

Code
A Aluminum
8 www.emerson.com
Description
March 2021 Rosemount 4390 Series Transmitters

Display

Code Description
00 No display

Communication protocol

Code Description
WA3 User configurable update rate, 2.4 GHz DSSS, IEC 62591 (WirelessHART)

Antenna options

Code Description
WK1 External antenna, adapter for black power module (I.S. Power module sold separately)
WM1 Extended range, external antenna, adapter for black power module (I.S. Power module sold separately)

Approvals

Code
I1 ATEX intrinsically safe
I7 IECEx intrinsically safe
Description

Probe cable gland

Code
G0 No gland - M20x1.5
G1 No gland - ½ in - 14 in NPT
G2 No gland - ¾ in - 14 in NPT
M3 Metric; nickel-plated brass
M4 Metric; stainless steel
N3 NPT; nickel-plated brass
N4 NPT; stainless steel
Description
Rosemount 4390 Series Transmitters 9
Rosemount 4390 Series Transmitters March 2021

Probe cable size range

Code Description
(1)
0
(2)
1
(2)(3)
2
(2)(4)
3
(1)
Available only with probe cable gland option G0, G1, and G2 no gland.
(2)
Not available with probe cable gland option G0, G1, and G2 no gland.
(3)
Not available with measurement option 2.
(4)
Not available with measurement option 1.
Not applicable
Standard multicable (5.5 mm to 12 mm OD / 3.5 mm to 8.1 mm ID) Applicable for corrosion and erosion
Armored cable BFOU(c) (12.5 mm to 20.5 mm OD / 8.4 mm to 14.3 mm ID) Applicable for corrosion
Armored cable BFOU(c) (16.9 mm to 26 mm OD / 11.1 mm to 19.7 mm ID) Applicable for erosion

Tag plates

Code Description
ZZ Customer information not required
TG Instrument tagging - customer information required (max. 30 characters)

Configuration

Code
C0 Standard factory configuration
C1 Factory custom configuration, descriptor, message fields, and wireless parameters
Description

Transmitter option 1

Code
Z Standard
Description

Factory option

Code
Description
Z Standard product
10 www.emerson.com
March 2021 Rosemount 4390 Series Transmitters
Rosemount 4390 Series Transmitters 11
00813-0100-4393
Rev. AB
March 2021
For more information: www.emerson.com
©
2021 Emerson. All rights reserved.
Emerson Terms and Conditions of Sale are available upon request. The Emerson logo is a trademark and service mark of Emerson Electric Co. Rosemount is a mark of one of the Emerson family of companies. All other marks are the property of their respective owners.
Loading...