Page 1
FULL BODY SHIATSU
Page 2
Assembly Instructions
12
Page 3
Page 4
Page 5
Instruction manual
06
To Begin:
The auto program buttons will begin to flash after the body scanning has completed.
you can now select a manual or auto program.
FuseOn/off
External Electric Plug
Power cord
Page 6
Instruction manual
08
Buttons
On Display:
Description
On Display:
Page 7
Page 8
Elite Robo-Pad Assembly Instructions. For questions, clarifications or
assistance call 1-800-592-0548
Your chair arms will be located in a separate box from the chair and require
installation. There are two accessories box located inside the large chair box which
contain the controller stand and upper air bag / speaker assembly'swhich also
require installation.
Tools required: Philips screwdriver, #5 Allen wrench / Hex key (included with chair)
Before you begin assembly, locate and remove the accessories boxes from the large
chair box. Inside the smaller accessories box is the #5 Hex key used to install the
arms in step one. Set the controller stand located in the same box aside to install in
step four. The speaker / upper air bag assembly's are located in the large
accessories box. These will be installed in step three.
Step 1: Install right arm.
Step 1A: Connect right arm wires and air pipe.Identify which arm is the right by
the controller stand mount located on the exterior of the arm. Identify the correct
side of the chair to install the arm. The Right arm will be where your right arm is
located when sitting in the chair
Locate the two wire plugs and air pipe on the right side of the chair. These plugs
should protrude from the square opening shown in the below picture. The wires may
be inside the frame of the chair and you will need to reach through the side of the
chair to pull them out through the square opening.
Locate the corresponding wires on the interior of the chair arm. Please note
that there is one wire and one air pipe from the arm. One wire from the chair
frame is not used on the right side only. Connect the white plug wire and air
pipe
Step 1B: Mount right arm to chair frame.
Note: Before mounting the arm, remove the silver attaching screws which are prescrewed into the arm.Locate the white round plastic mounts on the arm, and the
corresponding slots on the chair frame. Place the arm onto the frame at these
locations. The plastic mounts for the arm should slide into their respective locations
on the frame of the chair without applying force; press down slightly on the arm to
lock into place. The chair arm will still fit loosely until mounting screws are reattached. Note also the location of the mounting screw holes on the frame of the
chair.
Instruction manual
12
13
Chair
Small accessories
box-controller stand
Large accessories boxspeaker / upper air bag
assembly
Accessories boxes,in
large chair box
Contents of small
accessories box
Controller stand
screws
Hex key used in step
1 to install arms
Controller stand
Controller
stand mount
View of chair - Right
side
Air pipe,2 wires
through square
opening
May need to reach thro-
ugh this opening to locate
wires and air pipe
Air pipe
Two wires
Air pipe and
wire
Back view of arm
Leave this wire
unplugged
Connect wire
and air pipe
Assembly Instructions
Assembly Instructions
Page 9
Step 1C: Install the screws for the arm.
Install the screws removed in step 1B. The silver hex key provided will be
usedto tighten the screws
Rear screw location:
Front screw location:
Step 2: Install left arm.
Repeat the procedure for step one. Note that there are two additional plugs for the
left arm, three total, as shown below. Connect the plugs and air pipe accordingly.
The remainder of the procedure is the same as the right arm
Step 3: Install right and left upper air bag / speaker assembly.
Step 3A: Remove plastic covering panel from speaker assembly.
Locate the speaker / upper air bag assembly in the large accessories
box.Note the mounting posts and orientation of the speaker which will assist
you to differentiate the left from the right assembly
Instruction manual
14
15
Arm screw locations,
remove screws
before mounting
Arm
mounts
Back view
of arm
Screw hole
location
Arm mount locations
Screw location
Rear view of chair
Install screw as shown
Screw location
Front view of chair
Install screw as shown
Additional plugs
Left arm wires
Chair
Large accessories
box-speaker / air bag
assembly
Accessories boxes,in
large chair box
Speaker / air bag
assembiy front view
Speaker
Speaker / Air bag
assembly rear view
Mounting
posts
Assembly Instructions
Assembly Instructions
Page 10
Step 3B: Mount the speaker / air bag assembly
Once the panel is removed, note the location of the wire / air pipe hole in the
assmebly. This will be used to feed through the air pipe and wire from the mounting
locaiton on the chair.
Locate the mounting location for the speaker / air bag assembly on the chair, remove
the screws from this location
Mount the air bag / speaker assembly by inserting the mounting posts into the
large holes on the side of the chair. Ensure the speaker is facing upwards as
shown. Feed the air pipe and wire through the hole in the speaker / air bag
assembly
Instruction manual
16
Remove the plastic covering panel from the rear of the speaker assembly.
Remove the one screw from the edge of the panel. You may have to gently pry
the panel off of the assembly using a small flat head screwdriver.
17
Speaker / Air bag
assembly front view
Remove screw
Pry apart gently using
screwdriver
Hole for air pipe
and wire
Side view of chair
Speaker / air bag
assembly mounting
location
Remove mounting
screws
View from front
of chair
Speaker
Insert mounting
posts into large
holes
Feed air pipe
and wire
through hole
Insert mounting posts
into large holes
Assembly Instructions Assembly Instructions
Page 11
Install the controller stand onto the controller stand mount on the right arm, making
sure to line up the indent on the bottom of each piece. Insert screws into each side of
the controller stand
For questions, clarifications or assistance call 1-800-592-0548
Instruction manual
18
Step 4: Install remote stand. The remote stand is located in the small accessories
box, which is packaged inside the large chair box
19
Connect the air pipe and wire. Insert screws previously removed from side of chair
through holes shown below.
Step 3C: Replace covering panel: Replace covering panel, install with screw
previously removed.
Step 3D: Install opposite side speaker / air bag assembly. The process is the
same for each side.
Connect air pipe
and wire
Insert
screws here
Connect air pipe
and wire
Side view of chair with
assembly mounted
Covering panel
screw
Chair
small accessories box-
controller stand
Accessories boxes,in
large chair box
Contents of small
accessories box
Controller stand
screws
Controller stand
Controller
stand
Controller stand
mount
Indent
Install screws
Assembly Instructions
Assembly Instructions
Loading...