Safety information 2
Product description 5
Before first use 5
Control panel 6
Daily use 8
Clock functions 12
Automatic programmes 12
Using the accessories 13
SAFETY INFORMATION
Before the installation and use, read this
manual carefully:
•For your personal safety and the safety of
your property
• For the respect of the environment
• For the correct operation of the appliance.
Always keep these instructions with the appliance also if you move or sell it.
The manufacturer is not responsible if incorrect installation or use results in damage.
CHILDREN AND VULNERABLE
PEOPLE SAFETY
• This appliance can be used by children
aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use
of the appliance in safe way and understand the hazards involved. Children shall
not play with the appliance.
• Keep all packaging away from children.
There is the risk of suffocation or physical
injury.
• WARNING: Keep children and animals
away from the appliance when the door
is open or the appliance is in the operation, because it becomes hot. There is
the risk of injury or other permanent disability.
• If the appliance has Child Lock or Key
Lock (Control Lock) function, use it. It
prevents children and animals from accidental operation of the appliance.
Additional functions 16
Helpful hints and tips 16
Care and cleaning 17
What to do if… 21
Technical data 21
Installation 21
Environment concerns 22
Subject to change without notice.
GENERAL SAFETY
• Do not change the specifications of this
appliance. There is the risk of injury and
damage to the appliance.
• Do not let the appliance stay unattended
during operation.
• Switch off the appliance after each use.
INSTALLATION
• Only an approved electrician can install
and connect the appliance. Contact an
approved service centre. This is to prevent the risks of structural damage or
physical injury.
• Make sure that the appliance is not damaged because of transport. Do not connect a damaged appliance. If necessary,
contact the supplier.
• Remove all packaging, stickers and layers from the appliance before first use.
Do not remove the rating plate. It can invalidate the guarantee.
• Fully obey the laws, ordinances, directives and standards in force in the country where you use the appliance (safety
regulations, recycling regulations, electrical or gas safety rules etc.).
• Make sure that the appliance is disconnected from the power supply during the
installation.
• Be careful when you move the appliance.
The appliance is heavy. Always use safety gloves. Do not pull the appliance by
the handle.
• The electrical installation must have an
isolation device which lets you discon-
electrolux 3
nect the appliance from the mains at all
poles. The isolation device must have a
contact opening width of minimum 3
mm.
• You must have correct isolation devices:
line protecting cut-outs, fuses (screw
type fuses removed from the holder),
earth leakage trips and contactors.
• The shock protection parts must be fixed
in such a way that they cannot be undone without tools.
• Some parts of the appliance carry current. Close the appliance with furniture
and make sure that there are no free
spaces. It prevents electrical shock because you cannot accidentally touch
dangerous parts.
• Before the installation, make sure that the
kitchen cabinet has the recess dimensions applicable.
• Make sure that the appliance is installed
below and adjacent safe structures.
• Keep the minimum distances to the other
appliances and units.
• Install the appliance with its back and
one side close to the higher appliance.
The other side must be close to appliance with the same height.
• The appliance cannot be positioned on a
base.
ELECTRICAL CONNECTION
• The appliance must be earthed.
• Make sure that the electrical data on the
rating plate agree with your domestic
power supply.
• Information on the voltage is on the rating
plate.
• Always use a correctly installed shockproof socket.
• When you connect electrical appliances
to mains sockets, do not let cables touch
or come near the hot appliance door.
• Do not use multi-way plugs, connectors
and extension cables. There is the risk of
fire.
• Do not replace or change the mains cable. Contact the service centre.
• Make sure not to squash or cause damage to the mains plug (if applicable) and
cable behind the appliance.
• Make sure that the mains connection is
accessible after the installation.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug
– if applicable.
USE
• The appliance is only for domestic use.
Do not use the appliance for commercial
and industrial use.
• Only use the appliance for domestic
cooking tasks. This is to prevent physical
injury to persons or prevent damage to
property.
• Do not use the appliance as a work surface or storage surface.
• Do not put flammable products or items
that are wet with flammable products,
and/or fusible objects (made of plastic or
aluminium) in, near or on the appliance.
There is the risk of explosion or fire.
• The interior of the appliance becomes hot
during use. There is the risk of burns. Do
not touch the heating elements in the appliance. Use gloves when you insert or
remove the accessories or pots.
• Be careful when you remove or install the
accessories to prevent damage to the
oven enamel.
• Always stay away from the appliance
when you open the door while the appliance is in operation. Hot steam can release. There is the risk of skin burns.
• Discoloration of the enamel has no effect
on the performance of the appliance so it
is not a defect in the sense of the warranty law.
• To prevent damage or discoloration to
the enamel:
– Do not put any objects directly on the
appliance floor and do not cover it with
aluminium foil.
– Do not put water directly into the hot
appliance.
– Do not keep moist dishes and food in
the appliance after you finish the cooking.
• Do not use this appliance if it is in contact
with water. Do not operate the appliance
with wet hands.
• Do not apply pressure on the open door.
• Always close the appliance door when
you cook, even while grilling.
4 electrolux
CARE AND CLEANING
• Before maintenance, switch off the appliance and disconnect the appliance from
the power supply.
• Before maintenance, make sure that the
appliance is cold. There is the risk of
burns. There is the risk that the glass
panels can break.
• Keep the appliance clean at all times. A
build-up of fats or other foodstuff can result in a fire.
• Regular cleaning prevents the surface
material from deteriorating
•For your personal safety and the safety of
your property, only clean the appliance
with water and a soap. Do not use flammable products or products that can
cause corrosion.
• Do not clean the appliance with steam
cleaners, high-pressure cleaners, sharp
objects, abrasive cleaning agents, abrasive sponges and stain removers
• If you use an oven spray, follow the instructions from the manufacturer. Do not
spray anything on the fat filter (if applicable), the heating elements and the thermostat sensor.
• Do not clean the glass door with abrasive
cleaning agents or metal scraper. Heat
resistant surface of the inner glass can
break and shatter.
• When the door glass panels are damaged they become weak and can break.
You must replace them. Contact the
service centre.
• Be careful when you remove the door
from the appliance. The door is heavy!
• Do not clean catalytic enamel (if applicable).
PYROLYTIC CLEANING
Warning! Risk of burns.
• Keep children away from the appliance
while the Pyrolytic cleaning is in operation. The appliance becomes very hot.
• Provide good ventilation during and after
each Pyrolytic cleaning.
• Remove any pets (especially birds) from
the vicinity of the oven location during
and after the Pyrolytic cleaning and first
use maximum temperature operation to a
well ventilated area.
• Read carefully all the instructions for Pyrolytic cleaning.
RISK OF FIRE
• Open the door carefully. The use of ingredients with alcohol can cause a mixture
of alcohol and air. There is the risk of fire.
• Do not let sparks or open flames come
near the appliance when you open the
door.
• Do not put flammable products or items
that are wet with flammable products,
and/or fusible objects (made of plastic or
aluminium) in, near or on the appliance.
OVEN LAMP
• The type of light bulb or halogen lamp
used for this appliance is only for household appliances. Do not use it for house
lighting.
• If it becomes necessary to replace the
lamp, use one of the same power and
specifically designed for household appliances only.
• Disconnect the appliance from the power
supply before the replacement of the
oven lamp. There is the risk of electrical
shock.
SERVICE CENTRE
• Only an approved engineer can repair or
work on the appliance. Contact an approved service centre.
• Use only original spare parts.
DISPOSAL OF THE APPLIANCE
• To prevent the risk of physical injury or
damage
– Disconnect the appliance from the
power supply.
– Cut off the mains cable and discard it.
– Discard the door catch. This prevents
children or small animals from being
closed inside of the appliance. There is
the risk of suffocation.
PRODUCT DESCRIPTION
electrolux 5
1
2
7
6
Electronic programmer
1
Air Vents for Cooling Fan
2
Grill
3
Oven lamp
4
Fan
5
Rating plate
6
Food probe socket
7
BEFORE FIRST USE
Warning! Refer to "Safety information"
chapter.
INITIAL CLEANING
• Remove all parts from the appliance.
• Clean the appliance before first use.
Caution! Do not use abrasive cleaning
agents! This can damage the surface.
Refer to chapter "Care and Cleaning".
3
4
5
Oven shelf
•
For cookware, cake tins, roasts.
• Deep roasting pan
To bake and roast or as pan to collect
fat.
Food probe
•
To measure how far the food is cooked.
FIRST CONNECTION
When you connect the appliance to the
mains or after the power cut the display
shows the welcome text. After that you
have to set the language, date and time of
the day. Touch
tings. Touch OK to confirm.
PRE-HEATING
1.
Set function
ature.
2. Let the appliance operate without the
food for approximately 1 hour.
or to adjust the set-
and maximum temper-
6 electrolux
3.
Set function
and maximum temper-
ature.
4. Let the appliance operate without the
food for approximately 10 minutes.
5.
Set function
and maximum temper-
ature.
6. Let the appliance operate without the
This is to burn off the residue in the appliance. The accessories can become more
hot than usually. When you pre-heat the
appliance for the first time, the appliance
can make an odour and smoke. This is the
usual effect. Make sure the airflow is sufficient.
food for approximately 10 minutes.
CONTROL PANEL
ELECTRONIC PROGRAMMER
1
Touch the sensor field to operate the appliance.
Sensor
field
FunctionComment
23456
1
2
3
4
5
6
,
-DisplayShows the current settings of the appliance.
Right, Left
OKTo confirm. To start the set function.
Down Up
HomeTo cancel the selection and go back to the main menu.
On / OffTo activate and deactivate the appliance.
To move between the main menus.
It does not interrupt a heating function or programme
which operates.
To move in the submenus. To set the settings in the submenus. (example: temperature, time, weight).
To set the values:
• Touch the sensor field one time: To set the value in slow
steps
• Hold down the sensor field: To set the value in fast steps
DISPLAY
1
43
AreaComment
Main menu areaShows main menu items.
1
Can show:
• Heating function name and symbol
• Automatic program name and symbol
Main content area
2
Clock functions area
3
Time of day area
4
Clock functions and time area
• Temperature(s)
• Food probe status
•Help text
• Name of the day
•Date
Can show:
• Time related information for Clock functions
• Time progress indicator
If there are more than one clock function on at the same time,
the time progress indicator shows the status of the clock function that is longer than others.
Shows:
•Time of day
Reminder
1
Duration
1
2
Time progress indicator and uptimer
3
value
Time of day
4
electrolux 7
2
432
8 electrolux
DAILY USE
Warning! Refer to "Safety information"
chapter.
To operate the appliance you can use:
• manual mode - to set a heating function, the temperature and the cooking
time manually
THE MENUS IN OVERVIEW
Main menu
Sym-
bol
FunctionsIt contains list of the heating functions.
TimersIt contains list of the clock functions.
Food ProbeTo set the settings for the food probe.
CleaningIt contains the cleaning functions.
SettingsTo set other settings.
My Programmes
RecipesIt contains list of automatic cooking programmes.
Oven On
Oven Off
Menu itemDescription
• automatic programmes (recipes)- to
prepare a dish when you do not have a
knowledge or experience in cooking
It contains list of favourite cooking programmes
made by user.
It shows the settings of the appliance.
Submenus
Submenus for:
Oven functionDescription
Fan cookingFor baking on up to three oven levels at the same time.
ConventionalFor baking and roasting on one shelf level.
Pizza
Turbo Grill
Half Grill
Full GrillFor grilling flat foodstuffs in large quantities and for toasting.
Bottom Heat
Slow Cook
Functions
For baking on one oven level dishes that require more intensive
browning and a crispy base.
For roasting larger joints of meat or poultry on one level. The
function is also suitable for gratinating and browning.
For grilling flat foodstufs placed in the middle of the grill and for
toasting.
For baking cakes with crispy or crusty bases. For re-heating
pies and pastries.
For preparing especially tender, succulent roasts. For casseroles and hotpots.
Oven functionDescription
DefrostFor defrosting food.
DryingIdeal for drying fruit and herbs.
Keep WarmFor keeping pre-cooked food warm.
PreservingIdeal for jams and preserves.
Plate WarmingFor warming plates before serving.
Oven LampLights up without any heating function.
Submenus for: Timers
Sym-
bol
Set duration
Set start time
Set end time
Set+Go
Count up timer
Set reminder
Submenus for: Food Probe
Sym-
bol
Core temp. 30°
Submenus for: Cleaning
Sym-
bol
PyrolyticStarts the pyrolytic cleaning procedure.
Cleaning reminderReminds you when to clean the oven.
SubmenuDescription
Submenus for: Settings
Sym-
bol
Set clockTo set the time on the clock.
Set dateTo set the date.
Show time and dateTo show the time and date.
Heat and hold
SubmenuDescription
electrolux 9
Submenu
Submenu
It activates and deactivates the Heat and hold
function.
10 electrolux
Sym-
bol
Time extension
LanguageTo set the language for the display.
Key tones
Alarm/error tonesIt activates and deactivates the alarm tones.
Service
Highest value
Up key goes
Factory settings
SubmenuDescription
Submenus for: My Programmes
Sym-
bol
Add new
Name of the favourites
Submenus for: Recipes
Sym-
bol
Pork/Veal
Beef/Game/Lamb
Poultry
Fish
SubmenuDish
It activates and deactivates the Time extension function.
It activates and deactivates the touch fields
tone.
It shows the software version and configuration.
To set where the display shows higher value
on the temperature and time areas.
To set if the is to scroll up the list or to go
to upper item.
To set all settings to the factory settings (also
My programmes ).
or to set the temperature.
Touch OK. If you do not set the temperature, the appliance starts with the
preset temperature.
When you activate a heating function,
the display shows the temperature in
Ring Cake
Savarin Cake
Brownies
Muffins
Sweet Tart
Carrot Cake
Almond Cake
Fruit Tart
Cheese Pastry
White Bread
Farmer Bread
Russian Cake
Pasta Gratin
Chicory Gratin
Casserole
Cabbage Casserole
Bread/Rolls
Bread/Rolls, frozen
Apple Strudel, frozen
Fillet of Fish, frozen
Chicken Wings
Lasagne/Cannelloni, frozen
the appliance (in warm colour) and the
set temperature (in white colour).
STOPPING THE HEATING FUNCTION
Touch
.
SHOWING THE TEMPERATURE
Touch
or to go to Oven on/off .
The display shows the temperatures. The
temperature in the appliance is in warm colour. The set temperature is in white.
THE RESIDUAL HEAT INDICATOR
When you deactivate the appliance, the display shows the message that the temperature in the appliance decreases. You can
use the residual heat to keep the food
warm.
12 electrolux
CLOCK FUNCTIONS
SymbolFunctionDescription
Duration
Start time
End time
Set+Go
Count up timer
Reminder
Setting the clock functions
1. Go to Functions menu and set a heating function and a temperature.
2. Go to Timers menu and set the clock
function.
3.
Touch
or to set the necessary
time. Touch OK.
When the clock function ends, an
acoustic signal sounds. The appliance
deactivates. The colours on display
change and clock function symbol
flashes.
4. Touch a sensor field to stop the signals.
When you use Food probe, the functions Duration and End Time do not
operate.
You can set the Reminder function
when the appliance is on or off. To set
the Reminder function when the appli-
ance is off, touch
necessary time. Touch OK.
The Reminder function stays on also
when you deactivate the appliance.
SET+GO
Set the heating function and the temperature. In the Timers menu set the Set+Go
function and touch OK. The appliance is in
the standby mode. Touch any sensor field
to start the set heating function.
To set a count down.
To set when the appliance activates.
To set when the appliance deactivates.
To set the settings for the heating function and activate it later.
To set a count up. It shows how long the appliance operates.
This function has no effect on the operation of the appliance.
To set a countdown. This function has no effect on the operation of the appliance.
HEAT AND HOLD
You can activate or deactivate the
function in Settings menu.
The Heat and hold function keeps prepared
food warm at 80° for 30 minutes. It activates after the baking or roasting procedure
ends.
Conditions for the function:
• The set temperature is more than
80°C.
• The Duration function is set.
When the function ends, an acoustic signal
sounds.
The Heat and hold function operates for 30
minutes.
The Heat and hold function stays on if you
change the heating functions.
TIME EXTENSION
or to set the
You can activate or deactivate the
function in Settings menu.
The Time Extension function makes the
heating function continue after the set time
ends.
• Applicable for all heating functions with
function Duration or Weight Automatic .
• Not applicable for heating functions with
food probe.
AUTOMATIC PROGRAMMES
The automatic programmes give optimum
settings for each type of meat or other recipes.
• Meat programmes with Weight Automatic ( Recipes menu)
• Meat programmes with Food probe Automatic ( Recipes menu)
• Recipe Automatic ( Recipes menu)
electrolux 13
RECIPES WITH WEIGHT AUTOMATIC
This function automatically calculates the
roasting time. To use the function, it is necessary to input the food weight.
Activating the function:
1. Activate the appliance.
2. Set the menu Recipes . Touch OK.
3. Set the category and dish. Touch OK.
4. Set the Weight Automatic . Touch OK.
5.
Touch
Touch OK.
The automatic program starts. When time
ends, an acoustic signal sounds. Touch a
sensor field to deactivate the signal.
RECIPES WITH RECIPE AUTOMATIC
This appliance has a set of recipes you can
use. Recipes are fixed and you cannot
change them.
Activating the function:
1. Activate the appliance.
2. Set the menu Recipes . Touch OK.
3. Set the category and dish. Touch OK.
4. Set the Recipe Automatic . Touch OK.
RECIPES WITH FOOD PROBE
AUTOMATIC
1. Activate the appliance.
2. Set the menu Recipes . Touch OK.
3. Set the category and dish. Touch OK.
4. Set the Food Probe Automatic .
5. Touch OK.
6. Install the food probe.
When the programme ends, an acous-
tic signal sounds.
Use a sensor field to deactivate the
acoustic signal.
7. Remove the food probe.
When you set the option Manual, the
display shows automatic settings but
you can change them.
or to set the food weight.
MY PROGRAMMES MENU
You can store your favourite settings: duration, temperature or heating function.
Storing a programme
1. Activate the appliance.
2. Set a heating function, temperature and
time or an automatic program from
Recipes . Touch OK.
3. Set the menu My programmes .
4.
Touch
new . Touch OK. The display shows a
possible name for the programme.
5.
Touch
ber. Touch OK.
6.
To remove the last symbol, touch
OK.
7. Do step 5 again and again to set the
name of the programme.
8.
Touch
Touch OK.
If the memory is full, erase some entries
from the menu.
To change the name of a programme,
use the option Rename . Refer to
"Storing a programme".
Activating the programme
1. Activate the appliance.
2. Set the menu My programmes . Touch
OK.
3. Set the name of the programme. Touch
OK.
4. Set the option Start . Touch OK.
or to set the option Add
or to set the letter or num-
or
to set the option Remove . Touch
or to set the option Save .
USING THE ACCESSORIES
Warning! Refer to "Safety information"
chapter.
FOOD PROBE
The food probe measures the core temperature of the food. When the food is at the
set temperature, the appliance deactivates
automatically.
There are two temperatures to be set
• The oven temperature
• The core temperature of the food
The display shows the oven temperature
and the core temperature of the food.
14 electrolux
2134
56
Heating function
1
Food probe indicator
2
The core temperature of the food
3
The set core temperature of the food
4
The set temperature in the appliance
5
The temperature in the appliance
6
When the appliance operates at the set
temperature, the current temperatures
go off.
Important! Only use the supplied food
probe and the original spare parts.
1. Activate the appliance.
2. Put the tip of the food probe in the centre of the food.
3. Put the plug of the food probe in the
socket on the side wall of the appliance.
The display shows the menu Food
probe .
If you do step 2 before step 1, touch
or to set the menu Food probe .
4.
Touch
or to set the core temperature of the food in less than 5 seconds.
5. Go to the menu Functions .
6.
Touch
or to set the heating function and, if necessary, the oven temperature.
The food probe must stay in the food
and in the food probe socket during
the cooking.
7. When the food is at the set core temperature, an acoustic signal sounds.
The heating function deactivates.
Touch one of the sensor fields to stop
the signal.
Warning! Be careful when you remove
the tip and plug of the food probe. The
food probe is hot. There is the risk of
burns.
8. Remove the food probe plug and remove the food from the appliance.
9. Deactivate the appliance.
For meat programmes with the food
probe, refer to the menu Recipes .
TELESCOPIC RUNNERS
Installing telescopic runners
You can put the telescopic runners on each
level.
Make sure that the two telescopic runners
are on the same level.
The stop element that is at one end of the
telescopic runner must point up.
electrolux 15
2. Put the oven shelf on the telescopic run-
1
ners and carefully push them in the appliance.
Make sure you push back the telescopic
runners fully in the appliance before you
close the oven door.
°C
2
Caution! Do not clean the telescopic
runners in the dishwasher. Do not
lubricate the telescopic runners.
Using telescopic runners
With telescopic runners you can put and remove the shelves more easily.
1. Pull out the right and left hand telescopic runners.
°C
16 electrolux
ADDITIONAL FUNCTIONS
KEY LOCK
The Key Lock prevents an accidental
change of the heating function .
Activating the Key Lock
1. Activate the appliance.
2. Set the heating function and tempera-
ture.
3.
Touch
The display shows a message.
The Key Lock is active.
Deactivating the Key Lock
1.
Touch
The Key Lock is not active.
If you deactivate the appliance, the Key
Lock deactivates.
CHILD LOCK
The Child Lock prevents an accidental operation of the appliance.
Activating the Child Lock
1. Deactivate the appliance.
2.
Touch
til the display shows a message.
Deactivating the Child Lock
1. Do the above steps again.
If there is a power failure, the electronic
programmer keeps some of the settings (for example language setting and
the menu My Programmes ).
and OK at the same time.
and OK at the same time.
and OK at the same time un-
AUTOMATIC SWITCH-OFF
The appliance deactivates after some time:
• if you do not deactivate the appliance.
• if you do not change the oven temperature.
Oven temperatureSwitch-off time
30°C – 115°C12.5 h
120°C – 195°C8.5 h
200°C – 245°C5.5 h
250°C3.0 h
To operate the appliance after an automatic
switch-off, first deactivate the appliance
fully.
COOLING FAN
When the appliance operates, the cooling
fan switches on automatically to keep the
surfaces of the appliance cool. If you switch
off the appliance, the cooling fan continues
to operate until the appliance cools down.
SAFETY THERMOSTAT
To prevent dangerous overheating (due to
incorrect use of the appliance or defective
components), the oven has a safety thermostat, which interrupts the power supply.
The oven switches back on again automatically, when the temperature drops.
HELPFUL HINTS AND TIPS
Warning! Refer to "Safety information"
chapter.
• The appliance has four shelf levels. Count
the shelf levels from the bottom of the
appliance floor.
• The appliance has a special system
which circulates the air and constantly recycles the steam. With this system you
can to cook in a steamy environment and
keep the food soft inside and crusty outside. It decreases the cooking time and
energy consumption to a minimum.
• Moisture can condense in the appliance
or on the glass doors. This is normal. Always stand back from the appliance
when you open the appliance door while
cooking. To decrease the condensation,
run the appliance for 10 minutes before
cooking.
• Wipe away moisture after every use of
the appliance.
• Do not put the objects directly on the appliance floor and do not cover the components with aluminium foil when you
cook. This can change the baking results
and damage the enamel coating.
BAKING CAKES
• The best temperature for baking cakes is
between 150°C and 200°C.
• Preheat the oven for approximately 10
minutes before baking.
• Do not open the oven door before 3/4 of
the set cooking time is up.
electrolux 17
• If you use two baking trays at the same
time, keep one level empty between
them.
COOKING MEAT AND FISH
• Do not cook meat with weight below 1
kg. Cooking too small quantities makes
the meat too dry.
• To keep the red meat well-cooked outside and juicy inside set the temperature
between 200°C-250°C.
• For white meat, poultry and fish, set the
temperature between 150°C-175°C.
• Use a dripping pan for very fatty food to
prevent the oven from stains that can be
permanent.
• Leave the meat for approximately 15 minutes before carving so that the juice
does not seep out.
• To prevent too much smoke in the oven
during roasting, add some water into the
CARE AND CLEANING
Warning! Refer to "Safety information"
chapter.
• Clean the front of the appliance with a
soft cloth with warm water and cleaning
agent.
• To clean metal surfaces use a usual
cleaning agent
• Clean the oven interior after each use.
Thus you can remove dirt more easily
and it does not burn on.
• Clean stubborn dirt with a special oven
cleaner.
• Clean all oven accessories (with a soft
cloth with warm water and cleaning
agent) after each use and let them dry.
• If you have nonstick accessories, do not
clean them using an aggressive agents,
sharp edged objects or dishwasher. It
can destroy nonstick coating!
PYROLYTIC CLEANING
With the function Pyrolytic , you can clean
the oven using pyrolysis. Set the function in
the menu Cleaning .
Warning! The appliance becomes very
hot. There is the risk of burns.
dripping pan. To prevent smoke condensation, add water each time after it dries
up.
COOKING TIMES
Cooking times depend on the type of food,
its consistency, and volume.
Initially, monitor the performance when you
cook. Find the best settings (heat setting,
cooking time, etc.) for your cookware, recipes and quantities when you use this appliance.
Information on acrylamides
Important! According to the newest
scientific knowledge, if you brown food
(specially the one which contains starch),
acrylamides can pose a health risk. Thus,
we recommend that you cook at the lowest
temperatures and do not brown food too
much.
Important! Before you start the function
Pyrolytic , remove all the removable parts
(the shelf support rails, the accessories,
etc.) from the appliance.
1. Activate the appliance.
2.
Touch
ing . Touch OK.
3.
Touch
rolytic . Touch OK.
4.
Touch
the cleaning.
– LIGHT - for a low level of dirt (2:15)
– NORMAL - for a medium level of dirt
– INTENSE - for a high level of dirt
– AUTO - the appliance automatically
5. The display shows the messages.
Touch OK after each message.
When the appliance operates at preset
temperature, the door locks .
When the pyrolytic cycle starts, the
oven lamp does not work and the cooling fan works at a higher speed.
or to set the menu Clean-
or to set the function Py-
or to set the duration for
(2:45)
(3:15)
calculates which pyrolytic cycle to
use.
18 electrolux
Do not open the door during the heating up
time. If you open the door, you cancel the
pyrolytic cleaning cycle.
To stop the pyrolytic cleaning cycle, touch
.
Do not use the appliance until the door lock
symbol is off.
CLEANING REMINDER
It shows you when to do the cleaning. It
shows the message on the display after
some hours of the appliance operation.
Activate and deactivate the Cleaning reminder function in the menu Cleaning . The
Cleaning reminder function deactivates
when you set the appliance to the factory
settings.
CLEANING THE OVEN DOOR
The oven door has four panels of glass.
You can remove the oven door and the internal panels of glass to clean them.
Removing the oven door and the glass
panels
1. Fully open the door and identify the
hinge to the left side of the door.
2. Push the tightening component until it
pulls back.
3. Hold the pushed component with one
hand. Use a screwdriver with the other
hand to lift and turn the left side hinge
lever.
4. Identify the hinge to the right side of the
door.
5. Lift and turn the lever on the hinge.
electrolux 19
6. Close the oven door to the first opening
position (halfway). Then pull forward
and remove the door from its seat.
7. Put the door on a soft cloth on a stable
surface.
9. Turn the two fasteners by 90° and remove them from their seats.
90°
10. Carefully lift (step 1) and remove (step
2) the panels of glass one by one. Start
from the top panel of glass.
2
1
8. Release the locking system to remove
the panels of glass.
Clean the glass panels with water and
soap. Dry the glass panels carefully.
Installing the door and the glass panels
When the cleaning is completed, install the
glass panels and the oven door. Do the
above steps in the opposite sequence.
Make sure that you put the glass panels (
1
), ( 2 ) and ( 3 ) back in the correct se-
quence (refer to the illustration).
20 electrolux
123
The middle panel ( 2 ) has a decorative
frame. When you install it, make sure that
the screen-printing zone looks to the inner
side of the door. Make sure that after the
installation the surface of the glass panel
2
frame (
) on the screen-printing zones is
not rough when you touch it.
Make sure that you install the panels of
glass in the seats correctly (refer to the illustration).
SHELF SUPPORT RAILS
Removing the shelf support rails
1. Pull the front of the shelf support rail
away from the side wall.
2. Pull the rear shelf support rail away
from the side wall and remove it.
Installing the shelf support rails
Install the shelf support rails in opposite sequence.
The rounded ends of the shelf support
rails must point to the front!
OVEN LAMP
Warning! Be careful when you change
the oven lamp. There is a risk of
electrical shock.
Before you change the oven lamp:
• Deactivate the oven.
• Remove the fuses in the fuse box or de-
activate the circuit breaker.
Put a cloth on the bottom of the oven
to prevent damage to the oven light
and glass cover.
1. Turn the glass cover counterclockwise
to remove it.
electrolux 21
2. Clean the glass cover.3. Replace the oven light bulb with applicable 300°C heat-resistant oven light
bulb.
Use the same oven lamp type.
4. Install the glass cover.
WHAT TO DO IF…
Warning! Refer to "Safety information"
chapter.
ProblemPossible causeRemedy
The appliance does not
heat up.
The necessary settings are not
The Child lock is on.Refer to "Deactivating the Child
The fuse in the fuse box is re-
The display shows error
message "F....."
The oven lamp does not
operate.
Steam and condensation
settle on the food and in
the appliance.
If you cannot find a solution to the problem
yourself, contact your dealer or the service
centre.
We recommend that you write the data here:
Model (MOD.).........................................
Product number (PNC).........................................
Serial number (S.N.).........................................
The appliance is deactivated.Activate the appliance.
set .
leased.
Electronic error.Contact Service Center.
The oven lamp is defective.Refer to "Replace the oven lamp".
You left the dish in the appliance
for too long .
Do a check of the settings .
lock".
Do a check of the fuse.
If the fuse is released more than
one time, contact a qualified electrician .
Do not leave the dishes in the appliance for longer than 15-20 minutes after the cooking ends.
The necessary data for the service centre is
on the rating plate. The rating plate is on
the front frame of the appliance cavity.
TECHNICAL DATA
Voltage230 V
Frequency50 Hz
INSTALLATION
Warning! Refer to "Safety information"
chapter.
22 electrolux
22
590
594
540
560
576
2
50
A
B
550 min
560÷570
550 min
560-570
593
580
80÷100
ELECTRICAL INSTALLATION
Warning! Only a qualified and
competent person must do the
electrical installation.
The manufacturer is not responsible if
you do not follow safety precautions
from chapter "Safety information".
This appliance is supplied with a main plug
and a main cable.
ENVIRONMENT CONCERNS
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will
Loading...
+ 50 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.