Page 1
Instruction Manual
Page 2
Important Safety Instructions
When using an electrical appliance, basic
precautions should always be followed, including
the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE.
SAVE THESE INSTRUCTIONS
1. This appliance can be used by persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given supervision
or instruction concerning use of the appliance
in a safe way and understand the hazards
involved. Children shall not play with the
appliance. The appliance is not to be used if it
has been dropped, if there are visible signs of
damage or if it is leaking. Keep the appliance
out of reach of children when it is energized.
2. Do not use and charge the Appliance in
extremely hot or cold environments (below
0˚C/32˚F or above 40˚C/104˚F, above 65%
humidity), or it may affect battery life span.
The Appliance can be used to clean exterior
windows if it is properly tethered to a safe
position with the Carabiner, winds are calm,
and it is not raining or snowing.
3. Do not use this product in whole gale storms and
force-10 winds, or in areas where the altitude
exceeds 2000 meters(6162 feet).
4. Please ensure the Appliance is plugged in while
it is cleaning. The Appliance has a Safety Battery
that charges during use. The Safety Battery
powers the Appliance if it becomes unplugged or
the electricity fails.
5. Do not leave the Appliance unattended when it
is plugged in.
6. For household use ONLY (including exterior
window). Do not use the Appliance in
commercial or industrial environments.
7. Do not use the Appliance on cracked glass.
8. Only use accessories recommended or
supplied by the manufacturer. Only use the
Power Adapter supplied by the manufacturer.
9. Please make sure your power supply voltage
matches the power voltage marked on the
Power Adapter.
10. Do not use the Appliance on a framed window
with a frame smaller than 5mm (0.2 inches).
11. Do not use the Appliance on greasy windows.
12. When used in high humidity environment, the
cleaning performance will be affected.
13. Store the Appliance away from heat and
EN
2
Page 3
ammable materials.
14. In rainy weather, do not use the Appliance
on the exterior window to avoid the risk of
Appliance’s damage or falling.
15. Do not use the Appliance if it does not rmly
attach to the glass or has visible signs of damage.
16. To reduce the risk of electrical shock, do not
put the Appliance in water or other liquid. Do
not place or store Appliance where it can fall
or be pulled into a tub or sink.
17. Do not touch power plug with wet hands.
18. When charging the Appliance, do not place it
on other electrical appliances and keep it away
from re and liquid.
19. Take care not to damage the power cord. Do
not pull on or carry the Appliance by the power
cord, use the power cord as a handle, close
a window on the power cord, or put heavy
weights on the power cord. Keep power cord
away from hot surfaces.
20. Do not use with a damaged power cord or
receptacle. Do not use the Appliance if it is
not working properly, has been dropped,
damaged, or come in contact with water. It
must be repaired by the manufacturer or its
service agent in order to avoid a hazard.
21. If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent in order to avoid a hazard.
22. The plug must be removed from the receptacle
before cleaning or maintaining the Appliance.
Do not unplug the Power Adapter by pulling
on the power cord.
23. The Safety Battery must be replaced by the
manufacturer or its service agent in order to
avoid a hazard.
24. The Safety Battery must be removed and
discarded according to local laws and
regulations before disposal of the Appliance.
25. The Appliance must be disconnected from
the receptacle before removing the battery for
disposal of the Appliance.
26. Please dispose of used batteries according to
local laws and regulations.
27. Do not incinerate the Appliance even if it is
severely damaged. The battery can explode in
a re.
28. The Appliance must be used in accordance with
the directions in this Instruction Manual. The
company cannot be held liable or responsible for
any damages or injuries caused by improper use.
29. WARNING: For the purposes of recharging
the battery, only use the detachable supply
unit BLJ96W240400P-V provided with this
3
EN
Page 4
Appliance.
30. The robot contains batteries that are only
replaceable by skilled persons.
31. The plug and the Power Adapter must be used
indoor.
For EU Countries
For EU Declaration of Conformity information, visit
https://www.ecovacs.com/global/compliance
To satisfy RF exposure requirements, a separation
distance of 20 cm or more should be maintained
between this device and persons during device
operation.
To ensure compliance, operations at closer than this
distance is not recommended. The antenna used for
this transmitter must not be co-located in conjunction
with any other antenna or transmitter.
Class II
Short-circuit-proof safety isolating
transformer
Switch mode power supply
For indoor use only
Direct current
Alternating current
4
EN
Correct Disposal of this Product
This marking indicates that this product should
not be disposed of with other household
waste throughout the EU. To prevent possible
harm to the environment or human health
from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of
material resources. To recycle your used device,
please use the return and collection systems
or contact the retailer where the product was
purchased. They can safely recycle this product.
Page 5
Package Contents
Instruction Manual
WINBOT+ Safety Tether and Carabiner
+ Safety Battery
Note: Figures and illustrations are for reference only and may differ from actual product appearance.
Product design and specications are subject to change without notice.
Power Adapter
Instruction Manual
Mopping PadMeasuring Cup ECOVACS WINBOT Cleaning Solution
5
EN
Page 6
Product Diagram
WINBOT
Filling Opening
Bumper Rail
Bottom View
Spherical Sensors
Side Rollers
Driving Treads
Status Indicator Light/
START/PAUSE Button
Spray Outlet
Liquid Level Indicator
Fan
EN
Self-Cleaning Brush
Power Switch
Bottom Status Indicator Light
Suction Sensor
6
Page 7
Notes Before Cleaning Network Setup
Make sure Safety Tether and Carabiner have been connected with
WINBOT before using. (Connected by default. Do not disconnect
before cleaning.)
Note: Do not use WINBOT on a framed window with a frame narrower
than 5 mm(0.2”).
To enjoy all available features, it is recommended to control your
WINBOT via the ECOVACS HOME App.
a. Three Cleaning Mode
Fast Cleaning Mode: Ensure efcient window cleaning
Deep Cleaning Mode: Realize all-round cleaning
Spot Cleaning Mode: Say goodbye to stubborn stains
b. Manual Remote Control, Return to Corner:
Switch between interior and exterior window.
Manual remote control, to clean stubborn stains.
Return to Corner, to let WINBOT return to the specied corner
immediately.
c. Automatic and Manual Water Spraying
Automatic water spraying defaulted brings a better cleaning.
WINBOT is also equipped with manual water spraying function.
d. Smart Reminder of Consumables Replacement
Precise timing reminder, to get a better cleaning experience.
ECOVACS HOME
HOME
7
EN
Page 8
Quick Start
Connect WINBOT Power Cord, Power Adapter and Plug
1
Please ensure the battery is fully charged before using. Charging time will be approx. 2 hours.
*Do not cut the power off when WINBOT is running, otherwise it may lead to the risk of falling.
Step 2
Step 1
Connect correctly in the order shown above. Improper connection may cause charging abnormalities or damage to the battery.
Preparation before Use
2
Fill up the Reservoir
It is recommended to use with ECOVACS WINBOT Cleaning Solution. The maximum volume of the Reservoir is about 60ml, and it can spray for
about 60 minutes when the Reservoir is full.
Maximum 60ml
OR
Note: Do not add purified water and filtered water.
Do not add too much cleaning solution to overflow the Reservoir.
Using other cleaners could have an adverse effect on cleaning performance.
If the cleaning solution is used up, you can temporarily use tap water instead. Using the ECOVACS WINBOT Cleaning Solution can have a better
cleaning performance.
8
EN
Page 9
Install Mopping Pad
① Wet the Mopping Pad
Before using, wet the Mopping Pad manually.
③ Stick the Mopping Pad
Stick the Mopping Pad onto the Velcro at the bottom of WINBOT, and press
it with your hands to help the Mopping Pad stick firmly.
Narrow Side
② Wring the Mopping Pad out
Wring the Mopping Pad as dry as possible.
Wide
Side
Narrow Side
Wide
Side
Tie the Safety Tether
Properly tie the safety tether to a stable object that cannot be easily moved,
and lock the carabiner as shown below.
Please make sure using under supervision.
1 2
Note: To ensure safety, please make sure to secure the carabiner before use.
It is recommended to fasten the Safety Tether with the Carabiner on a firm and
safe metal railing.
9
EN
Page 10
Start
3
①Turn the Power Switch to "I ".
②Attach to the Window.
Method 1: Press on WINBOT within 1.5s. After the fan is completely
activated, attach WINBOT to the window.
Method 2: Evenly press the four Spherical Sensors onto the glass for 3s
and more to make it firmly attached.
WINBOT will start cleaning after it has attached to the window successfully.
* Do not stick the WINBOT too close to the edge when cleaning the frameless
glass. It is recommended to be more than 10cm away from the edge.
* WINBOT can only clean flat surfaces. Please make sure that the glass
thickness is not less than 3mm.
* Do not put the fan close to hair and other small objects after power on, so as
not to block the fan.
4
Maintenance during Cleaning
For heavily stained glass, please wash or replace the Mopping Pad
several times and clean the four Spherical Sensors in time.
Finish
5
Pause
During cleaning, press on WINBOT or pause it via App.
Remove WINBOT
Press on WINBOT for 5s and more to remove it from the window.
When cleaning is complete, WINBOT will return to the starting position
and beep. Press and hold for 5 seconds and more, and remove it after
the fan stops working.
EN
10
Page 11
Power Off Unplug WINBOT
Unfasten Safety Tether
1 2
11
EN
Page 12
Maintenance
Pour out the cleaning solution from the Reservoir. After using
ECOVACS WINBO Tcleaning solution, please rinse the reservoir with
the provided measuring cup.
OR
Mopping PadReservoir
Replace the Mopping PadEmpty the Reservoir
Remove the dirty Mopping Pad from WINBOT and place a clean new
one on it. Then, press the Mopping Pad with your hands to help it
stick firmly. Please make sure the Mopping Pad is correctly attached,
and do not cover the Spherical Sensors.
Narrow Side
Wide Side
Clean the Velcro at the bottom of WINBOT with a clean brush if it is
*
dirty. Do not wash with water to avoid damage caused by water.
Wash the Mopping Pad
Remove the Mopping Pad. Wash it with tap water, and wring it dry
before use.
Wide Side
Narrow Side
EN
Note: Wash with tap water.
Washing the Mopping Pad regularly can extend its service life.
If the Mopping Pad becomes worn or no longer fits exactly within the fastener
area, replace it with a new one to achieve optimal cleaning performance.
Explore more accessories at ECOVACS HOME App or at
https://www.ecovacs.com/global.
12
Page 13
Driving Treads
1 2 3
Before maintenance, please make sure that
the power switch is set to "I" and the fan
stops working.
Inspect the Driving Treads in ECOVACS
HOME App. Stop the Driving Treads if you
see dirt on them.
Spherical SensorsFan Side Rollers
After maintenance, you can install the
Mopping Pad to continue cleaning task.
Or turn the power switch to "O" to end task.
After WINBOT reports low battery, please fully charge it before usage and storage to avoid reducing the service life of battery.
*
If WINBOT will not be used for a long time, please fully charge it and turn it off before storage. Recharge it every six months to prevent the battery
*
from being over-discharged.
13
EN
Page 14
Status Indicator Light
Light Effect Status
WINBOT is fully charged.
WINBOT has successfully adhered itself to the glass and is ready to clean.
Status Indicator glows a continuous BLUE.
Status Indicator ashes BLUE slowly. WINBOT is paused and charging.
Status Indicator ashes BLUE. WINBOT is spraying.
Status Indicator stops glowing BLUE.
Status Indicator glows a continuous RED. WINBOT has a low battery. Please remove it from the window.
Status Indicator ashes RED. WINBOT has a problem. Please refer to section 5 Troubleshooting for details.
14
EN
WINBOT is cleaning.
WINBOT is paused.
The network setup is complete.
WINBOT is in sleep mode. Press
WINBOT is powered OFF.
to wake it up.
Page 15
Troubleshooting
NO. Malfunction Possible Causes Solutions
WINBOT moves in an irregular
1
pattern during cleaning.
2 WINBOT does not move.
WINBOT cannot move or
3
moves in circles.
Voice prompts insufcient
4
water in the Reservoir.
WINBOT stays still or moves
5
in an irregular pattern during
cleaning.
The Mopping Pad is too wet.
The Driving Treads are dirty. Clean the Driving Treads as described in section 3.
The Mopping Pad is attached improperly. Please remove the Mopping Pad and reattach.
There are gaps or cracks on the surface to
be cleaned.
The Mopping Pad Plate is blocked by
small obstacles on the glass.
The driving treads are stuck.
No ECOVACS WINBOT cleaning solution
in the Reservoir.
The bumper rail is stuck.
The bumper rail is damaged.
Spherical Sensors signal abnormity.
Fan malfunction.
Replace the Mopping Pad as described in section 3. Use
the ECOVACS WINBOT Cleaning Solution as described in
manual and restart the cleaning cycle.
Hold the Safety Tether or the Power Cord. Meanwhile,
press Direction Buttons in ECOVACS HOME App to let the
WINBOT leave the gap or barrier.
Check if there is any dust or debris on the Driving Treads. If
so, please clean the Driving Treads as described in section
3. Start WINBOT again. If problem persists, please contact
Customer Service.
Please add ECOVACS WINBOT cleaning solution. Do not
add puried water and ltered water.
Remove WINBOT from the window. Check if the bumper
rail is stuck. Clean the bumper rail and restart WINBOT. If
problem persists, please contact customer service.
A. Remove the Mopping Pad and re-attach it making sure it will
not cover or affect the Spherical Sensors.
B. Clean the Spherical Sensors as described in section 3.
C. If the problem persists, please contact Customer Service.
A. Clean the Fan as described in section 3.
B. If the problem persists, please contact Customer Service.
15
EN
Page 16
NO. Malfunction Possible Causes Solutions
Use the Direction Control buttons in the App to move
WINBOT stops moving after
6
adhering to the glass.
7 WINBOT is stuck. It is stuck by obstacles.
WINBOT is too close to the edge of the
glass or obstacles.
WINBOT away from the problem area and at least 10cm/4”
from window corners and obstacles. Restart WINBOT.
Alternatively, remove WINBOT from the window and put it at
least 10cm/4” from window corners and obstacles. Restart
WINBOT.
Fix the Safety Clasp and tether rmly. Hold WINBOT power
cord and meanwhile, use ECOVACS HOME App to move
WINBOT away from the stuck area. If the problem persists,
please contact Customer Service.
EN
16
Page 17
App Connection
Before connection, make sure WINBOT and the mobile phone meet the following requirements:
1. The Bluetooth of the mobile phone is turned on.
2. The WINBOT power switch has been turned on and the indicator light has been lit.
3. Please pair WINBOT in ECOVACS HOME App instead of the phone setting.
4. Co-frequency interference might occur between Bluetooth and Wi-Fi. It is recommended to keep WINBOT close to the mobile phone and distant
from the Wi-Fi router during pairing.
5. If the connection failed, please try to disconnect other Bluetooth devices, make sure WINBOT is not connected to other mobile phones, and try
again.
6. Bluetooth may be disconnected if WINBOT is too distant from the phone. Try to reconnect at a short distance.
7. For using WINBOT, you need to allow ECOVACS HOME App to obtain access to the location, Bluetooth, and mobile phone storage.
If the problems persist after trying the above methods, please contact customer service.
17
EN
Page 18
Technical Specifications
WINBOT Model WG888-12
Rated Input 24V 4A Rated Power 75W
Frequency 2400-2483.5MHz
Off/Standby Mode Power Less Than 0.50W
Power Adapter: BLJ96W240400P-V
Input：230V 50Hz 2.0A Output：24V 4A 96W
Output power of the wireless module is less than 100mW.
Note: Technical and design specifications may be changed for continues product improvement.
EN
18
Page 19
Ecovacs Home Service Robotics Co., Ltd.
No. 518 Songwei Road, Wusongjiang industry Park, Guoxiang Street,
Wuzhong District, Suzhou, Jiangsu, China.
451-2112-0302
Loading...