Duke SWD600-36 Service Manual

CLEARVIEW DAY COVER
Installation and
Operation Manual
CAUTION:
To view a video
scan the QR code above
Please read this manual completely before attempting to install, operate or service this equipment
This manual is Copyright © 2017 Duke Manufacturing Co. All rights reserved.
Reproduction without written permission is prohibited. Duke is a registered
trademark of the Duke Manufacturing Co.
Duke Manufacturing Co.
2305 N. Broadway
St. Louis, MO 63102
Toll Free: 1-800-735-3853
Fax: 314-231-5074
www.dukemfg.com/subway
REV F Date 11/06/2017
P/N 229652
Installation and Operation of: CLEARVIEW Day Cover
WARNING
CAUTION
CAUTION
TABLE OF CONTENTS
Safety Instructions .......................................................................................................2-3
Tools, Parts & Hardware ................................................................................................. 4
A. Installation of Day Cover ............................................................................................ 5
B. Installation and Adjustment of End Glass - end of lineup ........................................... 6
C. Installation and Adjustment of End Glass - Adjacent units ....................................... 7
D. Adjustment Front Glass.............................................................................................. 8
E. Operation - Drop-down Day Cove .............................................................................. 9
F. Troubleshooting .......................................................................................................... 9
G. Cleaning and Care .................................................................................................... 9
H. Service ....................................................................................................................... 9
I. Overview and Technical Specications .................................................................... 10
J. Installation Power Supply .........................................................................................11
K. Wiring Diagrams........................................................................................................11
L. Lineup Wiring............................................................................................................ 12
IMPORTANT SAFETY INSTRUCTIONS
Throughout this manual, you will nd the following safety words and symbols that signify important safety issues with regards to operating or maintaining the equipment.
Indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
Indicates a hazardous situation which, if not avoided, could result
in minor or moderate injury.
Indicates Important Information
Indicates electrical shock hazard which, if not avoided, could result in
Indicates hot surface which, if not avoided, could result in minor or
2
death or serious injury and/or equipment damage.
moderate injury.
Installation and Operation of: CLEARVIEW Day Cover
In addition to the warnings and cautions in this manual, use the following guidelines for safe operation of the unit.
Read all instructions before using equipment.
For your safety, the equipment is furnished with a properly grounded cord connector. Do not
attempt to remove or disconnect the grounded connector.
Install or locate the equipment only for its intended use as described in this manual.
Do not use corrosive chemicals in this equipment.
Do not operate this equipment if it has a damaged cord or plug, if it is not working properly, or if it
has been damaged or dropped.
This equipment should be serviced by qualied personnel only. Contact the nearest Duke authorized service facility for adjustment or repair.
Do not block or cover any openings on the unit.
Do not immerse cord or plug in water.
Keep cord away from heated surfaces.
Do not allow cord to hang over edge of table or counter.
The following warnings and cautions appear throughout this manual and should be carefully observed.
Turn the unit off, and disconnect the power source.
The procedures in this manual may include the use of chemical products. You must read the
Material Safety Data Sheets before using any of these products.
The unit should be grounded according to local electrical codes to prevent the possibility of electrical shock. It requires a grounded receptacle with dedicated electrical lines, protected by fuses or circuit breaker of the proper rating, in accordance with all applicable regulations.
Disposal of the unit must be in accordance with local environmental codes and/or any other applicable codes.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not store explosive substances such as aerosol cans with a ammable propellant inside the
appliance.
3
Installation and Operation of: CLEARVIEW Day Cover
TOOLS, PARTS & HARDWARE
TOOLS REQUIRED NOT INCLUDED:
Phillips Screw
Driver
PARTS AND HARDWARE INCLUDED:
Main Day Cover - Not Shown
216576
Silicone Sealant
7/16” Wrench 13mm Wrench 3/32 Allen
212105
Bushing 1ea.
223424 Hex
Head Bolt
10-24X1/2” 4ea.
Wrench
2501061 Stainless
Washer 4ea.
Adjustable
Pliers
225855 (120V) 225854 (240V)
Power Supply
523030 Bolt
1/4-20 X 1” 2ea.
225035 Gaskets 2ea.
4
223108 Bolt
1/4-20X3/4” 2ea.
223398 Plastic
Washer 4ea.
2501693 Plastic
Wrench 1ea.
524100 Plastic
Spacer 4ea.
226115
End Glass 1ea.
223390 1/4-20
Cap Nut 4ea.
Loading...
+ 8 hidden pages