Dual XDM7610 User Manual

XDM7610

INSTALLATION/OWNER’S MANUAL

AM/FM/CD/MP3/WMA Receiver with Detach Face

XDM7610 INSTALLATION

Preparation

Please read entire manual before installation.

Before You Start

• Disconnect negative battery terminal. Consult a qualified technician for instructions.

• Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

Getting Started

• Remove trim ring from unit,

• Remove 2 transit screws located
on top of the unit.

• Insert the supplied keys into the
slots as shown, and slide the unit
out of the mounting sleeve.

• Install mounting sleeve into
opening, bending tabs to secure.

• Connect wiring harness and
antenna. Consult a qualified
technician if you are unsure.

• Certain vehicles may require an
installation kit and/or wiring
harness adapter (sold separately).

• Test for correct operation and slide
into mounting sleeve to secure.

• Snap trim ring into place.

• Mount the iplug™ adapter to any
smooth clean surface using the
supplied double-sided tape or #2 x
3/8” Phillips head screws.

TYPICAL FRONT-LOAD DIN MOUNTING METHOD

2

XDM7610 INSTALLATION

Wiring Diagram

FUSE

When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XDM7610 uses one
10 amp ATM fuse located
beside the wiring connector.

3

XDM7610 OPERATION

Control Locations - Receiver

1 2

25

3 11 12 13

232122

24

Tune/Track Down

1

Mode/Search

2

Tune/Track Up

3

Preset #2/Repeat

4

Preset #1/Folder Down

5

Open

6

Volume

7

Eject

8

9

Preset #6/Folder Up

10

*Key #7

11

EQ

12

Audio/Setup

13

Display

6

5

4

8 9 107

19

1820

Mute

14

Tuner Scan/*Key #8

15

*Key #9

16

*Key #0

17

Band/Play/Pause

18

Infrared Se

19

Power

20

Preset #5

21

22

Preset #4/Intro

23

Preset #3/Random

24

Reset

25

AS/PS/Enter

17 141516

nsor

*Function keys 7, 8, 9 and 0 apply to MP3/WMA operation only.

4

XDM7610 OPERATION

Control Locations - Remote

1

2

3

Power

1

Volume Up

2

AS/PS/Enter

3

Audio/Setup

4

Tune/Track Up

5

Mute

6

Volume Down

7

Preset #3/Random

8

Preset #2/Repeat

9

Preset #6/Folder Up

10

19

18

17

4

5

6

7

16

8

15

14

13

9

10

11

12

EQ

11

Open

12

Display

13

Preset #5

14

Preset #4/Intro

15

Preset #1/Folder Down

16

17

Mode/Search

18

Tune/Track Down

19

Band/Play/Pause

5

XDM7610 OPERATION

General Operation

Front Panel Note:

Front Panel Removal

Power On/Off

Mode

Volume

Mute

Programmable

Turn-On Volume

Preset EQ Curves

The front panel is semi-permanently attached during
assembly. Please refer to the separate yellow instructions
(before installation) to make the front panel removable.

With the unit off, press
down. Gently squeeze the release tab located on the bottom
center underside and pull front panel down and away from
unit to remove. To install, insert left side first, then push right
side to secure.

Press POWER or any other button (except EJECT or OPEN)
to turn the unit on. Inserting a disc will turn the unit on
automatically. Press

Press MODE to select between tuner, CD player and auxiliary
input. Modes of operation are indicated in the display.

Adjust volume using rotary encoder (00-46).

Press MUTE to silence the audio. “MUTE” will flash in the
display. Press

Press and hold
selected volume level. "P-VOL" and the current volume level
will momentarily appear in the display.

Press EQ to select between POP, JAZZ, CLASSIC, BEAT,
ROCK and OFF (default) equalization curves. Any adjustment
to the Bass or Treble settings automatically cancels the
current EQ curve (if one is selected).

MUTE again to cancel.

OPEN to allow the front panel to slide

POWER to turn the unit off.

POWER for 3 seconds to program currently

Display

Set the Clock

12/24-hour Clock

6

Press DISP to select between clock and radio frequency
(tuner mode), clock and CD track/elapsed time (CD mode), or
clock and AUX (AUX mode).

With the unit on, press and hold
flash, then release. Press

TUNE

save the selected time.

The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10
mode, the clock will display 24-hour time (22:00).

to adjust the minutes. Press DISP momentarily to

ll

:

00). In European frequency spacing

DISP until the clock begins to

TUNE

to adjust the hours and

nn