Dual MXD40 User Manual

INSTALLATION/OWNERS MANUAL

AM/FM/CD Marine Receiver with Detach Face

MXD40

MARINE

2

MXD40 INSTALLATION

Preparation

Please read entire manual before installation.

Before You Start

• Disconnect negative battery terminal. (consult a qualified technician for instructions)

• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

Getting Started

• Remove 2 transit screws located on top of the unit.

• Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve.

• Install mounting sleeve into opening, bending tabs to secure.

• Connect wiring harness and antenna. (consult a qualified technician if you are unsure).

• Test for correct operation and slide into mounting sleeve to secure.

• Snap trim ring into place.

TYPICAL MOUNTING METHOD

3

MXD40 INSTALLATION

Wiring Diagram

FUSES

When replacing fuses, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage radio. The MXD40 uses one .5 amp AGC fuse (Ignition) and one 5 amp AGC fuse (Battery) located in-line.

Rear Preamp Output

GRAY

Connect to amplifier RCA Input

Remote Turn-On

BLUE

Connect to amplifier or power antenna. Insulate wire if not used.

Antenna Connector

RCA Cable

(sold separately)

AMP

Right Front

Gray/Black (-) Gray (+)

Left Front

White/Black (-) White (+)

5 AMP AGC Fuse

0.5 AMP AGC Fuse

BLACK

YELLOW

RED

Right Rear

Violet/Black (-) Violet (+)

Left Rear

Green/Black (-) Green (+)

Ground

Connect to chassis ground.

Memory

Connect to battery circuit or constant 12 volt source.

Accessory

Connect to existing ignition circuit or switched 12 volt source.

4

MXD40 OPERATION

Control Locations

Release

Volume

Tune/Track Up

Band

Bass Boost

Eject

Display

Play/Pause

Auto Store/Preset Scan

1 2 3 4 5 6 7 8 9

Preset 6

Preset 5

Preset 4/CD Random

Preset 3/CD Repeat

Preset 2/CD Intro

Preset 1/CD Top

Audio

Power

Tune/Track Down

10 11 12 13 14 15 16 17 18

17 16 15 14 13 12 11 10 9 8 7

1 2 3 4 5 6

18

The MXD40 Marine Receiver features UV resistant faceplate construction and clear-coated circuit boards for long lasting protection against the elements in the marine environment. Both chassis and mounting sleeve include an EDP (Electro-Deposit Plating) process for increased corrosion resistance.

MARINE

General Operation

5

MXD40 OPERATION

Press REL and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure.

*For semi-permanent faceplate installation, remove trim ring and install supplied Phillips head #1 screw through left side of mounting frame into faceplate.

Press PWR to turn the unit on. Inserting a CD will turn the unit on automatically. Press

PWR to turn the unit off.

Insert a CD or press

l

/IIto begin or resume playback.

Press

PWR or BAND to begin or resume tuner operation.

Press

BASS to activate and deactivate bass boost curve.

Activating this feature will enhance the bass frequencies when listening to music at low volumes.

Adjust volume using

VOL ▲ or VOL ▼ (00-39).

Press

DISP to display the clock. The radio frequency (tuner

mode) or CD track/elapsed time (CD player mode) show by default.

Press

DISP to display the clock, then release. Press and

hold

DISP then press TUNE to adjust the hours and

TUNE to adjust the minutes. Release DISP to save the

selected time.

Faceplate Removal

Power On/Off

CD Mode

Tuner Mode

Bass Boost

Volume

Display

Set the Clock

6

MXD40 OPERATION

General Operation

Press and hold for more than 2 seconds to RESET the unit upon initial installation. The

RESET button is located behind

the faceplate.

Press

AUD to select between Volume (default), Bass, Treble,

Balance & Fader.

Press

AUD until BA appears

Press

VOL ▼ or ▲ to adjust

(6 maximum / -6 minimum)

Press

AUD until TR appears

Press

VOL ▼ or ▲ to adjust

(6 maximum / -6 minimum)

Press

AUD until B appears

Press

VOL ▼ (LEFT) or ▲ (RIGHT) to adjust

(BL 16/BR 16) B 00 represents equal balance.

Press

AUD until F appears

Press

VOL ▲ (FRONT) or ▼ (REAR) to adjust

(FF 16/FR 16) F 00 represents equal balance.

Reset

Audio

Bass

Treble

Balance

Fader

7

MXD40 OPERATION

Tuner Operation

Press TUNE or momentarily to seek the next strong station.

Press

TUNE or for more than 2 seconds, then

press

TUNE or momentarily to move radio

frequency up or down one step at a time. Press and hold to advance quickly. If tuning is not adjusted for 2 seconds, the unit will return to seek tuning mode (default).

Press

BAND to select between FM1, FM2, FM3 and AM1,

AM2 bands.

Up to 18 FM stations and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button for more than 2 seconds. When stored, the preset number will appear in the display. The station can be recalled anytime by pressing the corresponding preset button.

Press

AS/PS for more than 2 seconds to automatically store

the six strongest stations in the current band.

Press

AS/PS for less than 2 seconds to scan presets 1-6 on

the current band, pausing for 5 seconds at each. Press

AS/PS again to cancel.

Seek Tuning

Manual Tuning

Band

Storing and Recalling Station

Presets

Automatically Store Stations

Preset Scan

8

MXD40 OPERATION

CD Player Operation

With the label facing up, insert a standard 5" CD into the CD slot. The CD will automatically begin playback.

Press the

EJECT button to stop and eject the CD. The unit

will change to tuner mode.

Press

TRACK to skip to the beginning of the next track.

Press

TRACK to return to the beginning of the current

track. Pressing

TRACK again skips to the beginning of

the previous track.

Press and hold

TRACK or TRACK to fast forward

or reverse a track.

Press

l

/ IIto temporarily stop CD playback.

Press

l

/ IIagain to resume playback.

Press

INT to play the first 10 seconds of each track.

Press

INT to cancel.

Press

RPT to continuously repeat selected track.

Press

RPT to cancel.

Press

RDM to play all tracks in random order.

Press

RDM again to cancel.

Press

TOP to begin playback from track 1.

Some CD-Rs may be incompatible with this unit, depending on media type and recording method. This model does not support CD-RWs.

Insert CD

Eject CD

Track Select

Fast Forward and Reverse

Pause

Intro

Repeat

Random

Top

CD-R Compatibility

9

MXD40 WARRANTY

Limited One-Year Warranty

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

Namsung America Inc. warrants this product to the original purchaser to be free from defects in material and workmanship, under normal conditions, for a period of one year from the date of the original purchase.

Namsung America agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equal new or renewed product in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase.

During the One-Year Warranty Period: For One Year from the date of purchase, your product will be replaced with a new, renewed or comparable product (whichever is deemed necessary) if it becomes defective or inoperative. This is done without charge to you. Replacement products are warranted for the balance of the original warranty period.

Who is covered? This warranty is extended to the original retail purchaser for products purchased and used in the U.S.A., in the 48 contiguous states ONLY.

What is covered? This warranty covers all defects in material and workmanship in this product. The following are not covered: installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product.

What to do? If the product requires warranty service, you must prepay the initial shipping charges. DUAL will pay the return shipping charges if the product is returned to an address within the USA.

Namsung America Inc. Attn: Returns Center 21318 64th Ave. South Kent, WA 98032 U.S.A. Toll Free: 1-866-626-7863

Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company’s negligence, actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages.

10

MXD40 OPERATION

Specifications

Signal-to-noise: >86dB Frequency response: 20Hz-20kHz, ±3dB Channel separation @ 1kHz: >65dB D/A converter: 16 Bit

Tuning range: 87.5MHz-107.9MHz FM mono sensitivity: 12dBf 50dB quieting sensitivity (stereo): 16dBf Stereo separation @ 1kHz: 40dB Frequency response: 30Hz-13kHz, ±3dB

Tuning range: 530kHz-1710kHz AM sensitivity: 30uV Frequency response: 80Hz-2kHz, ±3dB

Total system power: 100 Watts Peak Power output: 25Wx4 @ 14.4 VDC Power supply: 11-16 VDC, negative ground Speaker output impedance: 4 ohms Fuse: .5 amp fast blow AGC, 5 amp fast blow AGC Dimensions: 7" x 7" x 2" (178 x 178 x 51 mm)

Specifications subject to change without notice

CD Player

FM Tuner

AM Tuner

General

MXD40 OPERATION

Troubleshooting

11

Problem Cause Action

Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage

Check connections for proper voltage

(11~16VDC) Black wire not connected Check connection to ground Fuse blown Replace fuse Speaker wires not connected Check connections at speakers One or more speaker wires touching each

other or touching chassis ground

Insulate all bare speaker wires from

each other and chassis ground Yellow or red wire touching chassis ground Check for pinched wire Speaker wires touching chassis ground Check for pinched wire Incorrect fuse rating Use fuse with correct rating Unit is not mounted correctly or backstrap is

not secure

Check mounting sleeve and backstrap

support Physical defect in media (CD or CD-R) Check media for scratches High internal temperature Turn unit off for 1 hour Load/Eject operation error Press eject or RESET Focus adjustment error Clean or replace media Tracking auto adjustment error Clean or replace media Sled operation error Press eject or RESET Focus search operation error Press eject or RESET CLV (PLL) operation error Press eject or RESET TOC data read error Clean or replace media

Unit will not turn on

(no power)

Unit has power

(but no sound)

Unit blows fuses

Excessive skipping

Error 1 appears on display Error 2 appears on display Error 3 appears on display Error 4 appears on display Error 6 appears on display Error 7 appears on display Error 8 appears on display Error 9 appears on display

Namsung America Inc.

21318 64th Ave. South

Kent, WA 98032

Toll Free: 1-866-626-7863

EVOK0603-V01

INSTALLATION/OWNERS MANUAL

6.5" Dual Cone Marine Speakers

DMP65

MARINE

2

DMP65 INSTALLATION

Preparation/Installation

Please read entire manual before installation.

Before You Start

• Disconnect negative battery terminal. (consult a qualified technician for instructions)

• Use extreme caution when drilling holes to avoid damaging fuel lines, hydraulic lines or existing wiring.

Getting Started

• Determine where the speakers will be mounted. Ensure an area large enough for the speaker to mount evenly. Be sure the mounting location is deep enough for the speaker to fit.

• Using an appropriate tool, cut a 5.13" diameter mounting hole. Route speaker wires and connect to speakers, observing speaker polarity.

• Install speaker into opening using supplied hardware and test for correct operation.

TYPICAL MOUNTING METHOD

3

DMP65 WARRANTY