Dual MCP420BT, MCP420GH, MCP1055, MCP1054B, MCP105 Quick Start Manual

...

Installation

Before You Start

• Consult a qualified technician for instructions. Dual always recommends professional installation.

• Disconnect negative battery terminal.

• Remove trim ring from unit (if installed).

• Remove 2 transit screws located on top of the unit (if applicable).

• Insert the removal keys, and remove the mounting sleeve from the head unit.

Note: Most vehicles require an installation kit, wiring harness and/or antenna adapter (all sold separately) to properly install the head unit in the vehicle.

Installation Process

Quick Start Guide

For Mechless and CD Receivers

Not all features listed in this QSG

are available on all models.

To download the complete,

model-speciﬁc manual, please visit

www.dualav.com/support/manuals.php

or call 1-866-382-5476,

9AM-5PM EST (Monday-Friday).

1. Carefully remove the existing head unit.

2. Connect wiring harness. Consult a qualified technician if you are unsure.

3. Mount the head unit using the mounting sleeve or ISO brackets (depending on your vehicle’s dashboard).

4. Connect wiring harness and antenna. Test the head unit for correct operation.

5. Slide into mounting sleeve to secure, or mount the ISO brackets to the vehicle.

6. Snap trim ring into place.

Wiring Connections

The chart below the connection for each wire in the wiring harness.

Color Connection

Red 12V Ignition / Accessory

Yellow 12V Battery / Memory

Black Ground

Blue Power Antenna / Amp Turn-on

Grey Right Front (+)

Grey/Black Right Front (-)

White Left Front (+)

White/Black Left Front (-)

Violet Right Rear (+)

Violet/Black Right Rear (-)

Green Left Rear (+)

Green/Black Left Rear (-)

When a suitable ground wire is

not present in the vehicle wiring

harness, connect the black ground

wire to the vehicle chassis.

When replacing the fuse, make

sure new fuse is the correct type

and amperage. Using an incorrect

fuse could damage the radio.

Tip:

Fuse:

Mounting the Head Unit:

Typical DIN mounting

Step 1:

Insert the mounting sleeve into the

installation kit or dashboard.

Step 2:

Bend multiple mounting tabs around

the mounting sleeve until the

mounting sleeve is secure.

Step 3:

Connect all wiring harnesses and

slide the head unit into the mounting

sleeve until it clicks into place.

Mounting the Head Unit:

ISO mounting

Using the existing brackets or the brackets supplied with the installation kit, mount the brackets to the sides of

the head unit with the screws supplied

Installation

Dashboard or Installation Kit

Mounting Tabs

Dashboard or Installation Kit

Head Unit

Decorative

Bezel

Dashboard or Installation Kit

Mounting Sleeve

New

Radio

Existing

Brackets

with the head unit.

Power On/Off

Faceplate Removal

Changing Modes

Volume

Mute

Auxiliary Inputs

Reset

Setting the Clock

Display

Audio / Menu

To download the complete Owner’s Manual for your radio,

please visit www.dualav.com/support/manuals.php.

General Operation

Press the button to turn the unit on. Press again to turn unit off.

Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure.

Press MODE to select between AM/FM, CD player, auxiliary front/rear, USB and operation of iPod/iPhone. Modes of operation are shown in the display.

Adjust volume using volume knob.

Press to silence the audio. Press again to resume listening at the previously selected volume.

Insert a 3.5mm cable in the units front AUX port, or RCA cables into the rear AUX-IN connectors.

Press the RESET button to reset the unit back to the factory settings if abnormal operation occurs. The reset button is located behind the front panel.

With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE the hours and TUNE

DISP momentarily to save the selected time.

Press DISP to toggle display between various displayed information.

Press and hold AUDIO/MENU for more than three seconds to access the setup menu. Press AUDIO/MENU momentarily to select between the menu functions and rotate the volume knob left/right to adjust or activiate the desired function.

to adjust the minutes. Press

to adjust

AM/FM Tuner Operation

Seek Tuning

Manual Tuning

Storing Presets

Recalling Presets

To download the complete Owner’s Manual for your radio,

Press TUNE second to seek to the next strong station.

Press TUNE radio frequency up or down one step at a time. Press and hold to advance quickly.

Band

Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands. Up to six presets can be programmed for each band, enabling up to 18 FM stations and 12 AM stations to be stored in memory.

Up to 18 FM and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than two seconds. When stored, the preset number will appear in the display.

Preset stations can be recalled any time by pressing the corresponding preset button.

please visit www.dualav.com/support/manuals.php.

or TUNE

for more than one

momentarily to move

CD Operation*

Insert CD

Eject CD

Track Select

Fast Forward/

Reverse

Repeat

Random

CD-R/CD-RW

Compatibility

To download the complete Owner’s Manual for your radio,

With the label facing up, insert a standard size CD into the CD slot. Playback will begin automatically.

Press EJECT (located behind the front panel) to eject the CD. The unit will change to previous mode of operation.

Press TUNE track. Press TUNE current track. Pressing TUNE

beginning of the previous track.

Press and hold TUNE or reverse a track.

Pause

Press

Intro

Press INT to access the Intro menu, then turn the volume knob to select one of the following:

• OFF - Cancels the INT function.

• ALL - Plays the first 10 seconds of each track.

Press RPT to access the Repeat menu, then turn the volume knob to select one of the following:

• ALL - Plays all tracks on CD.

• TRACK - Continuously repeats selected track.

Press RDM to access the Random menu, then turn the volume knob to select one of the following:

• OFF - Cancels the RDM function.

• ALL - Plays all tracks in random order.

Some CD-Rs and CD-RWs may be incompatible with this unit, depending on media type and recording method. Refer to the online owner’s manual for details.

* Not available on all models.

please visit www.dualav.com/support/manuals.php.

to skip to the beginning of the next

to return to the beginning of the

or TUNE

/ II to temporarily stop CD playback. / II again to resume playback.

again skips to the

to fast forward

Playing MP3/WMA

Fast Forward and

Files

Track Select

Reverse

Pause

Folder Access

Repeat

Random

Intro

To download the complete Owner’s Manual for your radio,

please visit www.dualav.com/support/manuals.php.

MP3 / WMA Operation *

To play MP3/WMA files, insert a data CD, SD card or USB device containing MP3/WMA files.

Press TUNE Press TUNE song. Pressing TUNE the previous song.

Press and hold TUNE or reverse a track.

Press l/ II to temporarily stop playback. Press l/ II again to resume playback.

Press to select the next folder. Press to select the previous folder. Folder access is only available on discs or devices with more than one folder.

Press RPT to enter the Repeat menu, then turn the volume knob to select one of the following options:

• ALL - Plays all tracks on disc or device.

• TRACK - Continuously repeats selected track.

• FOLDER - Continuously repeats all files in folder.

Press RDM to enter the Random menu, then turn the volume knob to select one of the following options:

• OFF - Cancels RDM function.

• ALL - Plays all tracks in random order.

• FOLDER - Plays all tracks in folder in random order.

Press INT to enter the Intro menu, then turn the volume knob to select one of the following options:

• OFF - Cancels the INT function.

• ALL - Plays first 10 seconds of each track.

• FOLDER - Plays first 10 seconds of each track in the

selected folder.

* Not available on all models.

to skip to the beginning of the next song.

to return to the beginning of the current

again skips to the beginning of

or TUNE

to fast forward

Connect an iPod/

iPhone Device (sold

separately)

Song Select

Forward/Reverse

Pause

Repeat

Random

Intro

Music Search

Manual Control

for iPod

To download the complete Owner’s Manual for your radio,

please visit www.dualav.com/support/manuals.php.

Operation of iPod/iPhone*

To play music from an iPod/iPhone device, connect the USB cable (included with your iPod/iPhone device) to the unit’s USB port. Playback will begin automatically.

Press the beginning of the current song. Pressing to the beginning of the previous song.

Press and hold

Press Press

Press RPT to enter the Repeat menu, then turn the volume knob to select one of the following options:

• ALL - Repeats all tracks.

• SONG - Continuously repeats selected track.

Press RDM to enter the Random menu, then turn the volume knob to select one of the following options:

• OFF- Cancels the RDM function.

• ALL - Plays all tracks in random order.

• ALBUM - Plays all tracks in album in random order.

Press INT to enter the Intro menu, then turn the volume knob to select one of the following options:

• OFF - Cancels the INT function.

• ON - Plays first 10 seconds of each track.

Turn the volume knob to select between artists, songs, playlists, podcasts and audiobooks. Press SELECT to select the desired search category. Most search categories have subcategories to navigate through.

When “MANUAL” control is selected from the Setup Menu, the iPod or iPhone device can be controlled directly from the device’s interface. All functions except for volume can be used from the iPod or i Phone device.

Note: The firmware of the iPod/iPhone must be up dated to the latest version to be compatible with manual control model. Not all devices are compatible with manual control mode.

to skip to the next song. Press

/ II to temporarily stop playback.

/ II again to resume playback.

* Not available on all models.

to fast forward or reverse.

to return to

again skips

albums,

Bluetooth® Operation*

Preparation

Pairing a New

Device

Pairing

Additional

Devices

Disconnecting a

Device

Streaming Audio

Troubleshooting

To download the complete Owner’s Manual for your radio,

please visit www.dualav.com/support/manuals.php.

Before using a Bluetooth device, it must be paired and connected. Ensure that Bluetooth is activated on your device before beginning the pairing process.

The head unit broadcasts the pairing signal constantly when no devices are connected. Complete the pairing sequence from your Bluetooth device. Refer to the owner’s manual for your device for more details.

The device name is “DUAL BT” The Bluetooth passcode “1234”

Note: The head unit can be in any mode of operation when pairing is performed.

If a device is currently connected, press and hold to disconnect the current device before a new device can be paired. Then begin the pairing sequence from the new Bluetooth device.

Press and hold for 3 seconds to disconnect a connected device. The device will remain paired and appear in the SEARCH menu, but not be connected.

The head unit supports A2DP wireless streaming audio from a Bluetooth mobile device directly to your head unit. The following functions can be used to control the music:

• Press

playback.

* Not available on all models.

to skip to the next available audio track.

to skip to the previous audio track.

to toggle between play and pause during

Requirements

USB Connection

Changing Stations

Shuffle

Skip Track

Play/Pause

Thumbs Up

Thumbs Down

Device

Compatibility

To download the complete Owner’s Manual for your radio,

please visit www.dualav.com/support/manuals.php.

Pandora® Operation*

Control for Pandora requires:

• An iPhone device with a reliable data connection, or an iPod touch that is connected to wireless internet.

• The Pandora App installed on the iPhone/iPod device.

• An active account with Pandora (www.pandora.com).

• The USB sync cable included with iPod/iPhone device.

Connect an iPod touch or iPhone device (required, sold separtely) to the USB port, using the USB sync cable included with your iPhone device.

Press SELECT to display the stations menu. Turn the volume knob to cycle through the list of stations, then press SELECT when the desired station is highlighted.

Note: Stations must be created on your account prior to connecting your iPod/iPhone device to the head unit.

Press SELECT to display the stations menu. Choose “Shuffle” from the stations menu to shuffle songs from all of your stations.

Press

Press Press

Press the currently playing song.

Press different from the currently playing song.

Refer to the Owner’s Manual for a complete list of devices compatible with this head unit. Refer to www.pandora. com/everywhere/mobile for devices compatible with the Pandora mobile application.

gnitoohselbuorT

Note: Pandora is an internet service, carrier and data

charges may apply.

to skip the current song.

/ II to temporarily stop playback.

/ II again to resume playback.

to customize the station to play more songs like

to customize the station to play songs that are

* Not available on all models.

This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. (Note that select marine products carry a 2-year warranty. Please visit www.dualav.com for details.) Dual Electronics Corp. agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equal new, renewed or comparable product (whichever is deemed necessary) in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period.

Who is covered? This warranty is extended to the original retail purchaser for products purchased and used in the U.S.A.

What is covered? This warranty covers all defects in material and workmanship in this product. The following are not covered: installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or of the product.

What to do?

1. Before you call for service, check the troubleshooting guide in your owner’s manual. A slight adjustment of any custom controls may save you a service call.

2. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center.

3. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number with your shipment.

4. For more information and for the location of the nearest authorized service center please contact us toll-free at 1-866-382-5476 or by email at cs@dualav.com.

Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company’s negligence, actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this consequential damages.

Limited One-Year Warranty

damage occurring during return shipment

product. In no event shall the company be liable for indirect, incidental or

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Dual Electronics Corp. Toll Free: 1-866-382-5476 Monday-Friday, 9AM-5PM

www.dualav.com

iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone,

respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of

this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect

The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Namsung is under license.

Pandora, the Pandora logo, and the Pandora trade dress are trademarks of Pandora Media, Inc., used with permission.

The SD logo is a trademark of the SD Card Association.

wireless performance.

Other trademarks and trade names are those of their respective owners.

NSA0214-V01