Dr.Mach Mach Makrolux User manual

Makrolux

Halogen-spot lamp for consulting room and hospital

Dr. Mach
Lamps and Engineering
Mounting instructions Directions for use
MAKROLUX
Dr. Mach
GmbH u. Co., Flossmannstrasse 28, D-85560 Ebersberg
Tel.: +49 (0)8092 2093 0, Fax +49 (0)8092 2093 50
Internet: www.dr-mach.com, E-mail: info@dr-mach.de
59010001 Edition 02 13.04.2000 / Bak Page 1/13
Makrolux
Dr. Mach
Lamps and Engineering
List of contents
1. Safety instructions .......................................................................................... Page 3
2. Mounting instructions ..................................................................................... Page 4
2.1 Pre-mounting of the stand ........................................................................ Page 4
2.2 Mounting the stand with the five-feet base............................................... Page 4
2.3 Mounting of the lamp................................................................................ Page 5
2.4 Wall mounting........................................................................................... Page 5
2.5 Table mounting......................................................................................... Page 5
3. Directions for use ........................................................................................... Page 6
3.1 ON/OFF switch......................................................................................... Page 6
3.2 Positioning................................................................................................ Page 6
4. Cleaning ......................................................................................................... Page 7
4.1 Lamp head ............................................................................................... Page 7
4.2 Protective disk (filter disk) ........................................................................ Page 7
5. Maintenance................................................................................................... Page 7
5.1 General information.................................................................................. Page 7
5.2 Changing of spare parts ........................................................................... Page 8
5.2.1 Changing the halogen bulb............................................................... Page 8
5.2.2 Changing the protective disk (filter disk)........................................... Page 8
6. Data................................................................................................................ Page 9
6.1 Technical data .......................................................................................... Page 9
6.1.1 Technical data of the lamp Makrolux ................................................ Page 9
6.1.2 Technical data of the stand............................................................... Page 9
6.2 Environmental conditions ......................................................................... Page 10
7. CE-mark ......................................................................................................... Page 10
8. Disposal.......................................................................................................... Page 10
9. Spare parts..................................................................................................... Page 11
9.1 Lamp head / arm ...................................................................................... Page 11
9.2 Five-foot base........................................................................................... Page 11
9.3 Stand tube ................................................................................................ Page 12
9.4 Spare parts for lamp head / arm............................................................... Page 13
9.5 Spare parts for five-foot base ................................................................... Page 13
9.6 Spare parts for stand tube........................................................................ Page 13
59010001 Edition 02 13.04.2000 / Bak Page 2/13
Makrolux
Dr. Mach
Lamps and Engineering
1. Safety instructions

Please pay attention to the directions for use when handling the lamp!

The lamp is supplied with integrated connection lead, earthed plug and a transformer 230/12V 20W integrated in the plug. The lamp is to be used only with this transformer. The socket to be used for the lamp must be installed according to the requirements stipulated by the IEC or VDE 0107. Please check that the earthed socket is available within the working area of the lamp.
This device is not suitable for use in hazardous locations. The lamp is manufactured and tested according to the standards IEC DIN 601. The lamp is tested for electromagnetic compatibility according to the standards EN 60601-1-2 / 4. 1994. The lamp is classified as a group 1 device according to the MPG (law for medical products).
Repairs to the lamp and special installation work on the reflector or at the transformer should only be carried out by ourselves or a company expressly authorised by our­selves.
The manufacturer is only responsible for the safety of the lamp if repairs and altera­tions have been carried out by themselves or a company who can guarantee that the safety regulations have been observed.
The manufacturer is not liable for personal or material damages if the lamp is misap­propriately or incorrectly operated or misused.
Attention: The lamp can be disconnected from mains only by pulling the plug off the earthed socket.
All Dr. Mach stand lamps are supplied with all installation and connection parts and components. For packaging reasons, the five-foot stand is supplied in dismantled state. The stand tube is always assembled as a unit and only needs to be attached to the foot with the lower fastening screw.
59010001 Edition 02 13.04.2000 / Bak Page 3/13
Makrolux
9
14
6 7
13
2. Mounting instructions
8
2
1
3
5
17
12
4
11
16
2.1 Pre-mounting of the stand
Fix the upper part 1 of the stand tube (with ball handle 2) to the lower part of the stand tube 3 and tighten.
2.2 Mounting the five-feet base with the stand tube
15
For mounting the stand proceed as follows:
Place the central base 4 onto the stand
tube 25 5. The stiffness is to ensure a tight fit that is free from any movement.
Pre-mount the cam catch plate 6 (cams
point inwards), with the lock washer 7 and cheese head screw M8 8, so that the ex­tension arm 9 can still fit easily into the central base. Insert the extension arm 9 into the central base from above holding
10
the cam catch plate 6 against from the op­posite side.
Insert the other 4 extension arms 10-13 in
the sequence shown in the left figure into the central base. The extension arms are held by the cams of the cam catch plates.
Remark: Mount the two locking rollers 14 and 15, and the two electrically conductive rollers 16 and 17 as shown in the figure (not next to each other).
Tighten the catch plate with an Allen key
SW6 (approx. 15Nm). The cams of the catch plate must mate with the drill holes of the extension arms so that every extension arm is tightly fitted to both the central base and stand tube. The cams also prevent the extension arms from being pulled out.
Dr. Mach
Lamps and Engineering
59010001 Edition 02 13.04.2000 / Bak Page 4/13
Makrolux
Dr. Mach
Lamps and Engineering
2.3 Mounting the lamp
21
18
19
20
Disengage clamping lever 19 to open plas-
tic joint 18 just enough , so that it can be put on stand 20.
The swivel arm 21 has to be mounted n
such a way, that its position is above the joint 18 (see figure).
Adjust height and radius of the swivel arm
and tighten clamping lever 19, so that the friction of the joint holds the lamp in the re­quested position.
2.4 Wall mounting
Mark the position of the holes to be drilled in the wall using the wall bearing.
Drill the holes and insert the dowels.
Insert the wall bracket into the location hole of the wall bearing and fix it with the clamping
grub screw.
Mount the plastic joint 18 on the wall bracket.
To mount the lamp proceed as described at point 2.3.
2.5 Table mounting
Screw on table clamp on the table in the desired position.
Insert the lamp with the upper part 1 of the stand tube into the clamp hole and fix with the
clamping grub screw.
59010001 Edition 02 13.04.2000 / Bak Page 5/13
Makrolux
22
19
3. Directions for use
3.1 ON/OFF switch
Use the switch 22 at the lamp housing to turn the lamp on and off.
21
3.2 Positioning
For height adjustment the arm 21 can either be swivelled or adjusted in height by loosening ad­justing lever 19.
The self-locking joints 23, 24 can be adjusted by tightening the clamp screw.
Dr. Mach
Lamps and Engineering
Clamp screw
23,24
59010001 Edition 02 13.04.2000 / Bak Page 6/13
Makrolux
Alc. 20 %
25,26
4. Cleaning
4.1 Lamp head
The lamp has a high-quality surface, which can be cleaned with conventional cleaning agents.
Only use disinfectant with less then 20% alco­hol.
4.2 Protective disk (filter disk)
The protective disk 25 is made of an high-quality plastic, the filter disk 26 is made of high quality glass. For cleaning use lukewarm water and a soft viscose sponge. Pay attention to the follow­ing during cleaning:
- Wipe over the protective disk 25 (filter disk
26) with a wet cloth (never use a dry cloth!).
- Only use disinfectant with less then 20%
alcohol.
Wipe protective disk 25 (filter disk 26) after cleaning with an antistatic, non-fluffy cloth.
Dr. Mach
Lamps and Engineering
5. Maintenance
5.1 General information
The lamp is constructed in such a way, that regular service intervals are not required.
If necessary, the clamp screws at the self-locking joints have to be tighten.
59010001 Edition 02 13.04.2000 / Bak Page 7/13
Makrolux
28
27
25,26
Dr. Mach
Lamps and Engineering
30
29
29
31
5.2 Changing of spare parts
5.2.1 Changing the halogen bulb
Dr. Mach uses special halogen bulbs as illumi­nants. Only original Dr. Mach replacement bulbs may be used. The use of other bulbs can lead to a consider­able reduction of the light power and increase in the thermal load.
Attention! Disconnect from mains before changing the bulb.
To change the bulb proceed as follows:
Loosen and remove four fixing screws 27 at
the upper front ring 28.
Lift the upper front ring 28 off the lamp hous-
ing 29.
Push halogen bulb 12V 20W 30 backwards
and turn anticlockwise (bayonet catch).
Replace upper front ring 28 on the lamp
housing 29 and fix it with the screws 27.
Remark: The halogen bulbs have a service life of ap­prox. 1000 hours without any deterioration in their luminosity.
5.2.2 Changing the protective disk
(filter disk)
To change the protective disk (filter disk) pro­ceed as follows:
Loosen and remove two fixing screws 31 at
the lower front ring 28.
Lift the lower front ring 28 off the lamp hous-
ing 29.
Press the three retaining clamps H at the
lower front ring 28 carefully to the edge and lift the protective disk 25 or the filter disk 26.
Insert the new protective disk or filter disk in
reverse order.
H
59010001 Edition 02 13.04.2000 / Bak Page 8/13
28
Makrolux
Dr. Mach
Lamps and Engineering
6. Data
6.1 Technical data
6.1.1. Technical data of the lamp Makrolux
~ Wechselstrom Alternating current
Pr Primärseitig 230V / 0,35A Primary side
Sek Sekundärseitig 12V AC / 1,66A Secondary side
Hz Hertz – Frequenz 50 / 60Hz Frequency Hertz
Schutzgrad Type „B“ Class of protection
6.1.2. Technical data of the stand
Lamp type
Data
Makrolux
Number of exten­sion arms
Stand foot
Stand tube
Swivel arm + lamp head
Length of arm 310mm
Rollers
Approx. length 95cm – 145cm
Diameter 25mm
Extension yes
Power supply no
Suitable for article no.
Swivel arm and lamp head
Mounting
Swivel arm to stand
1100 1012 00 1101 1012 00
pre-mounted
5
50mm
59010001 Edition 02 13.04.2000 / Bak Page 9/13
Makrolux
Dr. Mach
Lamps and Engineering
6.2 Environmental conditions

Operation

Temperature +10°C +40°C Relative atmospheric humidity 30% 75% Air pressure 700 hPa 1060 hPa

Transport / storage

Temperature -10°C +50°C Relative atmospheric humidity 20% 90% Air pressure 700 hPa 1060 hPa
Min. Max.
Min. Max.
7. CE- mark
The products Makrolux comply to the standards 93/42/EEC for medical products of the European Community’s Council.
8. Disposal
The components of the lamp should be properly disposed at the end of its shelf-life. Make sure, that the materials are carefully separated. The lamp does not contain any danger goods. The components should be disposed according to the contained materials.
59010001 Edition 02 13.04.2000 / Bak Page 10/13
Makrolux
9.1 Lamp head, arm
22
28
9. Spare parts
Dr. Mach
Lamps and Engineering
38
37
30
27
47
39
28
46
29
31
25,26
21
40
36
42
44
23
45
24
43
59010001 Edition 02 13.04.2000 / Bak Page 11/13
Makrolux
9.2 Five-foot base
9.3 Stand tube
33
02
32
Dr. Mach
Lamps and Engineering
48
18
34
01
35
19
41
59010001 Edition 02 13.04.2000 / Bak Page 12/13
Makrolux
Dr. Mach
Lamps and Engineering
9.4 Spare parts for lamp head / arm
Item Qty. Name EDVNO Remarks
21 1 Swivel arm 01080205 22 1 ON/OFF switch 67340004 23 1 Tilt joint – upper part 01080203 24 1 Tilt joint – lower part 01080204 25 1 Protective disk 01011208 26 1 Filter disk 01011203 27 4 Sheet metal screw DIN 7982-2,2x6 65872001 28 2 Front ring 01011202 29 1 Housing 01011201 30 1 Halogen bulb (bayonet catch) 12V 20W 67100203 31 2 Sheet metal screw DIN 7982-2,2x6 65872001 36 1 Connection cable with plug transformer
12V 20W 37 1 Lamp socket 67320004 38 1 Cap screw 03080214 39 1 Handle 01011204 40 1 Strain relief 67700002 42 1 Brake washer 01080209 43 1 Screw 01080207 44 1 Axis 01080206 45 1 Spring washer 65542001 46 1 Screw M3x6 DIN 427 65752001 47 2 Screw M3x5 DIN 7985 65152006
67200202 STt 20/230
9.5 Spare parts for stand tube and five-foot base
Item Pos. Name EDVNO Remarks
01 1 Stand tube (biparted) 74952001 1871 02 1 Spherical handle 74952003 18 2 Plastic joint 01080202 19 1 Clamping lever 74503003 32 2 Stand clamp 01080201 33 1 Screw M5x50 DIN 603:N/A2 65822003 34 1 Spring washer DIN 137 A5 Fst 65542001 35 1 Washer A5,3 DIN 125 Fst 65512003 41 1 Reducing bushing 74952002 48 1 5-foot base 74905003
40 SW M8
59010001 Edition 02 13.04.2000 / Bak Page 13/13
Loading...