DORO AUB300i User Manual [sv]

AUB 300i

!"# $%&

*+, -./'()

456 789:0123

-54%34/2%

2%$)!,

2%#!,,

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

CID

DIAL

1

2

19

3

4

5

6

7

8

9

10
11

English

1 Line connector
2 Scroll UP/DOWN buttons
3 Dial displayed number
4 Wall mounting hanger hook
5 Clear/OK button
6 One-Touch memories
7 Headset socket
8 Handset socket
9 Mute button and LED
10 Store button

18
17

16

15

14

13
12

11 Recall button
12 Redial button
13 Hands free button and LED
14 Headset button and LED
15 Speaker volume control
16 Handset/Headset volume control
17 Ringer/Message waiting indicator
18 Caller ID/Phone book
19 Input socket for additional equipment

English

Important!

The earpiece of the handset may attract small ferromagnetic objects such as staples and pins, care should
be taken when placing the handset near these items.

Connection

1. Connect the curly cord to the handset and to the socket marked q on the side of

the telephone.

2. Place the handset into the cradle.

3. Connect the telephone line cord to the socket marked T on the telephone, and to

a telephone network wall socket. Lift the handset and listen for the dial tone. Your
telephone is ready to operate approximately 10 seconds after connection, the display
indicators appear after about 60 seconds..

Setting the language, clock or contrast

If you wish to set the language, clock or contrast settings, follow the steps below:

1. Press and hold v until the display ashes ENGLISH.

2. Select the required language using v/V. Press OK.

3. Select the desired contrast setting (3=normal) using v/V. Press OK.

4. Set the correct hour (00-23) using v/V. Press OK.

5. Set the correct minute/s using v/V. Press OK.

6. Set the correct day using v/V. Press OK.

7. Set the correct month using v/V. Press OK.

8. Select the required pause setting (2 seconds=normal) using v/V. Press OK.

The display

In standby mode the date and time, number of new and total number of calls stored
in the Caller ID memory will be displayed. Immediately following the connection of a
call, a call timer will be shown on the display.

Hearing aid compatible

This telephone is hearing aid compatible. Select the T mode on your hearing aid to
enable this feature.

Ringer

The ringer volume, melody and tone can be selected using the switches located on the
underside of the telephone behind the battery cover:

Labels/protective cover

The memory index cover can be accessed by carefully removing the transparent plastic

using a small at blade screwdriver or similar.

1

English

Wall mounting

The telephone can be wall mounted using an optional wall mount bracket.
The wall mount bracket is available as an accessory, part number WB200/300 in white
or black.

1. Fix the wall mount bracket on the back of the telephone.

2. Secure two screws, vertically positioned 83 mm apart.

3. The screws should locate into the two keyholes on the wall mount bracket.

4. Activate the hanging peg (located by the hook switch) by lifting it upwards and

rotating it 180 degrees.

Making a call

Lift the handset and dial the required telephone number.

Pre-Dialling

You can enter and correct a telephone number before dialling.

1. Dial the required telephone number. Mistakes can be erased using C.

2. Press DIAL OR press s to dial the number.

Redial

Repeatedly press REDIAL to view the last 5 numbers dialled. Press DIAL OR press

s

to dial the number.

Volume control

The Handset/headset earpiece volume may be increased or decreased during a call.
Use on the side of the phone to adjust the volume.
To adjust the speaker volume (hands free and group listening) use on the side
of the phone.

Recall

Press the recall button RECALL followed by the extension number to transfer calls
when connected to a PBX (TBR only). Access to additional network services can be
gained by using the recall button RECALL, * and # keys. Contact your network
operator for more information.

Mute button

The handset/headset/hands free microphone can be disconnected during a call by
pressing MUTE. Press MUTE once more to reactivate the microphone.

The MUTE LED will illuminate while the function is active.

2