Page 1
®
RM2452 RM2453 Installation and Operating Instructions
INST ALLATION AND
OPERATING INSTRUCTIONS
REFRIGERATOR FOR LP-GAS AND ELECTRIC OPERATION
RM 2452 RM 2453
Contents:
Installation 4
Operating Instructions 9
Maintenance & Service 1 1
Page
FOR YOUR SAFETY
If you smell gas:
1. Open windows.
2. Don’t touch electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier .
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
W ARNING: Improper installation,
adjustment, alteration, service or
maintenance can cause injury or
property damage. Refer to this
manual. For assistance or additional
information consult a qualified
installer, service agency or the gas
supplier.
Pour votre sécurité
Si vous sentez une odeur de gaz:
1. Ouvrez les fenêtres.
2. Ne touchez à aucun interrupteur.
3. Éteignez toute flamme nue.
4. Avertissez immédiatement votre fournisseur de gaz.
Pour votre sécurité
Ne pas entreposer ni utiliser de l’essence ni
d’autres vapeurs ou liquides inflammables à
proximité de cet appareil ou de tout autre
appareil.
Avertissement: Une installation, un réglage,
une modification, une réparation ou un
entretien non conforme aux normes peut
entraîner des blessures ou des dommages
matériels. Lisez attentivement le mode d’emploi fourni avec l’appareil. Pour obtenir de
l’aide ou des renseignements supplémentaires, consultez un installateur ou un service
d’entretien qualifié ou le fournisseur de gaz.
USA Corporate Office CANADA
Service Office 2320 Industrial Parkway Elkhart, IN 46515 Dometic Distribution Inc.
Dometic Corporation 866 Langs Drive
509 South Poplar Street Cambridge, Ontario
LaGrange, IN 46761 For Service Center Assistance N3H 2N7 Canada
Phone: 260-463-4858 Call: 800-544-4881 Phone: 519-653-4390
822 70 10-01
®
Page 2
Page 3
Heater
Cover,
Terminal block
FIG. 1
Flexible cord
Manual gas shutoff valve
ABCDE
12 Volts
12 Volts
DC
DC
Reigniter
Heater
12 volt terminal block,
3-way only
Inlet fitting
Refrigerator control panel
Flue baffle
Protection
cover
Screw for protection cover
Burner jet
Drain water hose
AC
FUEL SELECTOR
OFF
OFF ON
FLAME PUSH WHEN LIGHTING THERMOSTAT
LEGEND
A. ON/OFF, Fuel Selector Switch
B. Thermostat Knob, Gas/Electric
C. Flame Failure Safety Valve
Push-button
D. Piezo Igniter
E. Flame Indicator
FIG. 2
3
Page 4
INSTALLATION
GENERAL INSTRUCTION
This appliance is designed for storage of foods and
storage of frozen foods and making ice.
This appliance is certified under the latest edition of
ANSI Z21.19•CSA 1.4 Refrigerators using gas fuel.
The installation must conform with local codes, or in
absence of local codes, the following standards as applicable.
In the U.S. the installation must conform with:
1. National Fuel Gas Code, ANSI Z223.1/NFP A 54
(latest edition).
2. Recreational Vehicles Code, ANSI A119.2 (latest
edition)
3. Manufactured Home Construction and Safety
St andard, T itle 24 CFR, Part 3280.
If an external electrical source is utilized, the refrigerator, when inst alled, must be electrically grounded in accordance with local codes or, in the absence of local
codes, the National Electrical Code, ANSI/NFP A 70 - (latest edition).
The lower side vent is fitted with a panel, which provides
an adequate access opening for ready serviceability of
the burner and control manifold of the refrigerator. This
should be centered on the back of the refrigerator.
CERTIFIED INST ALLA TION
Certified installations require one roof vent and one lower
side vent.
For “Certified Vent System Kits” see page 14.
For further information contact your dealer or
distributor.
METHODS OF INSTALLATION
The method of installation is shown in FIG. 3.
It is essential that all maximum or minimum dimensions
are strictly maintained as the performance of the refrigerator is dependent on adequate flow of air over the rear
of the refrigerator.
NOTE: The upper vent should be
centered over the condenser coil
at the back of the refrigerator.
In CANADA, the installation must conform with:
1. Natural Gas and Propane Installation Code,
CSA B149.1
2. CSA Z240 RV Series, Recreational V ehicles.
3. Current CSA Z240.4, Gas-equipped Recreational
Vehicles and Mobile Housing.
If an external electrical source is utilized, the refrigerator, when inst alled, must be electrically grounded in accordance with local codes or, in the absence of local
codes, the Canadian Electrical Code, CSA C22.1, Part s
I and II - (latest edition).
VENTILATION
The installation shall be made in such a manner as to
separate the combustion system from the living space
of the mobile home or recreational vehicle. Openings
for air supply or for venting of combustion products shall
have a minimum dimension of not less than 1/4 inch.
Proper installation requires one lower fresh air intake
and one upper exhaust vent. The ventilation kits shown
in this instruction manual have been certified for use
with the refrigerator models listed in the Table.
For “Certified Vent System Kit s” see page 14.
Minimum
ventilation
height
Condenser
FIG. 3
The ventilation kits must be installed and used without
modification. An opening toward the outside at floor level
in the refrigerator compartment must be provided for
ventilation of heavier-than-air fuel gases. The lower vent
of the recommended kits is provided with proper size
openings. The flow of combustion and ventilating air must
not be obstructed.
4
Page 5
VENTILA TION HEIGHTS
Refer to FIG. 3 page 4.
Installation with roof Minimum ventilation
vent and lower side vent heights in:
Refrigerator Inches mm
RM 2452 37-3/4 960
RM 2453
CLEARANCES
Minimum clearances in inches to combustible materials
are:
G: Top 0
K: Side 0
L: Bottom 0
M: Rear 0
N: See NOTE: Clearance “N” below.
FIG. 4
K
G
K
L
NOTE: Wood Strip
MUST be in place
NOTE: Clearance “M” is between the rearmost part of
the refrigerator and the wall behind the refrigerator.
NOTE: Clearance “N” is the distances between the bot-
tom of the lower side vent to the roof material. For ventilation height, see table VENTILA TION HEIGHTS.
See Figures 3 and 4.
FIG. 5
Side view View from above
D
H
N
M
C
D
WA
B
Refrigerator Dimensions Dimensions
Overall Recess
Model
Height Width Depth Height Width Depth
ABCHWD
RM 2452 inch 37-3/8 24-7/8 24-11/16 36-9/16 23-11/16 24
RM 2453
mm 948 632 627 928 602 610
This method of installation and these clearances will give you adequate space for service and proper installation.
5
Page 6
INSTALLING REFRIGERATOR IN
ENCLOSURE
NOTE: DO NOT install the appliance directly on
carpeting. Carpeting must be removed or
protected by a metal or wood panel beneath
the appliance, which extends at least full
width and depth of the appliance.
NOTE: A wood strip must be in place across the upper
opening of the enclosure. The top frame of the refrigerator will be anchored to the wood strip with screws.
See FIG. 4.
The refrigerator must be installed in a substantial enclosure and must be level. When installing the refrigerator
in the enclosure, all areas within the recess in which the
refrigerator is installed must be sealed.
Make sure that there is a complete seal between the
front frame of the refrigerator and the top, sides and
bottom of the enclosure. A length of sealing strip is applied to the rear surface of the front frame for this purpose, see FIG. 6. The sealing should provide a complete isolation of the appliance’s combustion system from
the vehicle interior.
NOTE: Be careful not to damage the sealing strip when
the refrigerator is put in place.
1
2
FIG. 7
2. Once the lower front strip is slipped under the
hinge, the part is possible to swing into place as
shown in FIG. 8.
3
FIG. 6
Securing the Refrigerator
After the refrigerator is put in place, (ensuring a combustion seal at the front frame), the refrigerator is to be
secured in the enclosure with six screws (not included).
The screws have to be installed in the following order:
STEP 1: Two screws installed through the front base,
which includes the lower front strip installation.
The refrigerator is provided with a lower front strip
(shipped as a loose part). The front strip is to be attached
after the refrigerator is set into the cut-out opening.
1. Install the lower front strip by sliding it under the
bottom hinge plate, as shown in FIG. 7. The hinge
plate can be on the right or left side depending on
the door swing.
FIG. 8
3. Secure the refrigerator and the lower front strip with
two screws:
One screw through the hinge, and on the opposite
side one screw through the lower front strip. (FIG. 8).
STEP 2: Two screws installed in the top frame.
The top decoration panel must be removed from the refrigerator before the screws can be installed.
Open the door and gently push the tabs out of the hole
in the hinge with a flat blade screwdriver, (both sides).
See FIG. 9.
Carefully tilt the top decoration panel and lift up to remove from top frame.
Install the two screws in the top frame, the holes are
accessible from underneath.
Seal the opening for the screws with aluminum tape.
6
Page 7
GAS CONNECTION
Hook up to the gas supply line is accomplished at the
manual gas valve, which is furnished with a 3/8" SAE
(UNF 5/8" -18) male flare connection. All completed con-
2
nections should be checked for leaks with soapy water.
! WARNING
DO NOT use a flame to check for gas leaks.
FIG. 9
1
Replace the top decoration panel.
Make sure the tabs snap back into the holes in the hinge
plate.
STEP 3: Two screws installed in the rear base.
See FIG. 10.
Failure to follow the sequence in securing the refrigerator
in the enclosure can cause leakage between the frame
and cabinet. Any space between the counter, storage
area or ceiling and top of the refrigerator greater than
1-1/2 inches should be blocked. The heat produced at
the rear of the refrigerator will become trapped in this
space, making the top of the refrigerator hot and reduce
the efficiency of the refrigerator.
Hole for drain water hose
FIG. 10
Drain water hose
A hole must be drilled through flooring see FIG. 10.
The installer MUST make sure that the hose does not
kink when run through the floor. Seal around the hose
that goes through the drilled hole. If a longer hose than
supplied is required to get the water to drain outside of
the vehicle, the installer will have to supply the extra
length of hose.
The gas supply system must incorporate a pressure
regulator to maintain a supply pressure of not more than
11 inches water column.
When testing the gas supply system at test pressures in
excess of 1/2 psi, the refrigerator and its individual shutoff
valve must be disconnected from the gas supply piping
system.
When testing the gas supply system at pressures less
than or equal to 1/2 psi, the appliance must be isolated
from the gas supply piping system by closing its individual manual shutoff valve.
In case detailed instructions on the installation and connection to the gas supply are required, contact your
dealer or distributor.
TESTING LP GAS SAFETY SHUTOFF
The gas safety shutoff must be tested after the refrigerator is connected to the LP gas supply.
To test the gas safety shutoff, proceed as follows:
1. Start the refrigerator according to the instructions for
Gas Operation. See section Operating Instructions.
2. Check that the gas flame is lit. This can be observed
on the flame indicator E. The red indicator is in the
green field, (ON).
3. Close the gas valve by turning the knob A back to
“OFF” position.
4. Wait for one minute.
5. Remove protection cover (see FIG. 1). Open the gas
valve by turning knob A to position “GAS” without
pushing the buttons C and D. Apply a non-corrosive
commercial bubble solution to the burner jet.
6. No bubbles should appear at the opening of the
burner jet. The presence of bubbles indicates a defective gas safety shutoff, and service is required.
7. If no bubbles were present at the burner jet, the gas
safety valve is working properly. Rinse jet thoroughly
with fresh water before proceeding. Be careful not to
damage the burner jet.
Replace the protection cover and turn the main switch
OFF and back ON. See instruction for Gas Operation , section Operating Instructions. Normal operation of the burner should return. Allow the burner to
operate for a minimum of 5 minutes.
7
Page 8
ELECTRICAL CONNECTION
120 Volts AC Connection
The refrigerator is equipped with a three-prong (grounding) plug for your protection against shock hazards and
should be plugged directly into a properly grounded
three-prong receptacle. DO NOT cut or remove the
grounding prong from this plug. The free length of the
cord is 2 feet and therefore recommended that the receptacle be located to the left side of the refrigerator
(viewed from the rear) and approximately 6 inches from
the floor (see FIG. 11). This allows easy access through
the vent door. The cord should be routed to avoid direct
contact with the burner cover, flue cover or any other
components that could damage the cord insulation.
120 Volt AC
receptacle
6”
MAXIMUM TOTAL CONDUCTOR WIRE LENGTH
(in feet and meters)
RM 2453
Wire length AWG
17 ft.
10 AWG
5 m
27 ft.
8 AWG
8 m
The connections must be clean, tight and free from corrosion. If not, a resulting voltage drop will cause a decreased cooling capacity.
! CAUTION
DO NOT operate the refrigerator on 12 volt when
the vehicle is parked. The amperage draw of the
12-volt DC heating element can discharge a battery in a very short time. The installation of a 12volt DC operated refrigerator requires a relay to
be installed on the tow vehicle or in the caravan. The relay will automatically shut off the 12
volt DC power to the refrigerator when the ignition is turned off. (See FIG. below).
FIG. 11
12 Volts DC Connection
3-way refrigerator model
The 3-way refrigerator model RM 2453, has one terminal block marked “12 Volts DC heater”, located on the
back of the refrigerator cabinet. (See FIG. 1).
The refrigerator must be connected to the battery circuit
with two wires of adequate capacity to avoid voltage drop.
The wire gauge should be chosen with consideration to
the wire length in accordance with the table below.
The 12 volt DC circuit must be fused. Max. fuse size is
20 amps for RM 2453.
Correct polarity must be observed when connecting to
the DC supply.
DO NOT use the chassis or vehicle frame as one of the
conductors. Connect two wires at the refrigerator and
route to the DC supply.
The refrigerator will draw 15 amps at 12 volt DC.
Breaker
point
Ignition
coil
Switch key
Relay
Refrigerator
Battery
8
Page 9
OPERATING INSTRUCTIONS
AED C B
AC
OFF ON
FUEL SELECTOR
FLAME PUSH WHEN LIGHTING THERMOSTAT
IMPORT ANCE OF LEVELING A
REFRIGERATOR
In an absorption refrigerator system, ammonia is liquefied in the finned condenser coil at the top rear of the
refrigerator. The liquid ammonia then flows into the
evaporator (inside the freezer section) and is exposed
to a circulating flow of hydrogen gas, which causes the
ammonia to evaporate, creating a cold condition in the
freezer.
When starting this refrigerator for the very first time, the
cooling cycle may require up to four hours of running
time before the cooling unit is fully operational.
The tubing in the evaporator section is specifically sloped
to provide a continuous movement of liquid ammonia,
flowing downward by gravity through this section. If the
refrigerator is operated when it is not level and the vehicle is not moving, liquid ammonia will accumulate in
sections of the evaporator tubing. This will slow the circulation of hydrogen and ammonia gas, or in severe
cases, completely block it, resulting in a loss of cooling.
OFF
NOTE: After changing an LP tank, or after a long shut-
off period, the gas line is likely to be filled with air. You
may have to repeat the lighting procedure several times
to purge the air out of the gas lines.
As soon as the necessary cold temperature inside the
cabinet has been reached, adjust the thermostat knob
to required setting.
! WARNING
Most LP gas appliances used in recreational vehicles are vented to the outside of the vehicle.
When parked close to a gasoline pump, it is
posible that the gasoline fumes could enter this
type of appliance and ignite from the burner
flame, CAUSING A FIRE OR AN EXPLOSION.
FOR YOUR SAFETY, when refueling, shut off all
LP gas appliances which are vented to the outside.
Any time the vehicle is parked for several hours with the
refrigerator operating, the vehicle should be leveled to
prevent this loss of cooling.
The vehicle needs to be leveled only so it is comfortable
to live in (no noticeable sloping of floor or walls).
When the vehicle is moving, the leveling is not critical,
as the rolling and pitching movement of the vehicle will
pass to either side of level, keeping the liquid ammonia
from accumulating in the evaporator tubing.
GAS OPERATION
Before starting the refrigerator, check that all the manual
gas valves are in the ON position. DO NOT forget the
manual shutoff valve on the rear of the refrigerator see
FIG. 1.
1. To start the refrigerator, turn knob A to the “GAS”
position.
2. Turn the thermostat knob B to position 4.
3. Push the button C in until it reaches the bottom - and
hold, push the button D for the piezo igniter several
times to light the burner. This can be observed on
the flame indicator E. When the flame is on, the red
indicator is in the green field, (ON).
4. After the gas is lit keep the button C pressed for 10
seconds. Release the button and check that the RED
indicator is in the GREEN field, (ON).
5. To shut off the refrigerator turn the knob A to “OFF”
position.
ELECTRIC OPERATION
1. Check to be sure that the power cord is properly connected to the power supply. (See FIG. 11). If the refrigerator is equipped for 12 volt DC operation, the
tow vehicle or caravan engine should be running to
prevent discharging the battery.
2. Turn the knob A to position marked “AC” for 120 volt
AC operation or “DC” for 12 volt DC operation.
3. Turn the thermostat knob B to position 4.
4. To shut off the refrigerator turn the knob A to “OFF”
position.
THERMOSTAT
The refrigerator is equipped with a thermostat that can
be adjusted by turning the knob B to different setting to
maintain the desired cabinet temperature.
At OFF In gas operation, the thermostat closes its main
valve and the burner runs continuously at the
bypass rate, just enough to keep the burner lit.
In electrical operation, the contacts in the thermostat are open and the heating elements are
off.
At MAX In gas operation, the thermostat allows the
burner to remain on high flame continuously. In
electric operation, the heating element is “ON”
continuously. Lowest cabinet and freezer temperatures are obtained at this setting.
9
Page 10
The thermostat can be adjusted between “MAX” and
“OFF” to obtain the desired cabinet temperature.
The closer the knob is to “MAX” - the colder the cabinet
temperature. The closer the knob is to “OFF” - the warmer
the cabinet temperature.
When the thermostat reaches the set temperature, it will
cut the burner back to bypass or, in electric operation,
shut off the heating element.
The setting of the thermostat is not critical, but we recommend it be adjust to maintain a dry frost on the cooling fins. Adjust the thermostat knob closer to “MAX” when
the outside temperature becomes warm.
HOW TO USE THE REFRIGERATOR
FOOD STORAGE COMPARTMENT
The food storage compartment is completely closed and
unventilated, which is necessary to maintain the required
low temperature for food storage. Consequently, foods
having a strong odor or those that absorb odors easily
should be covered. Vegetables, salads etc. should be
covered to retain their crispness. The coldest positions
in the refrigerator are under the cooling fins and at the
bottom of the refrigerator. The warmer areas are on the
upper door shelves. This should be considered when
placing different types of food in the refrigerator.
FROZEN FOOD STORAGE
COMPARTMENT
Quick frozen soft fruits and ice cream should be placed
in the coldest part of the compartment, which is at the
bottom of the aluminum liner. Frozen vegetables, may
be stored in any part of the compartment.
This compartment is not designed for deep or quick freezing of food. Meat or fish, whether raw or prepared, can
be stored in the frozen food storage compartment provided they are precooled first in the refrigerator. They
can be stored about three times longer in the frozen food
compartment as compared to the fresh food compartment. To prevent food from drying out, keep it in covered dishes, containers, plastic bags or wrapped in aluminum foil.
Ice cubes can be made in the freezer compartment.
For faster ice making, the trays should be placed in direct contact with the bottom of the freezer compartment.
! CAUTION
DO NOT use a hot air blower. Permanent damage
could result from warping the metal or plastic parts.
DO NOT use a knife or an ice pick, or other sharp
tools to remove frost from the freezer compartment.
They can create a leak in the ammonia system.
When all frost has melted, dry the interior of the refrigerator with a clean cloth. Replace all food and set the
thermostat to “MAX” for a few hours, then reset the thermostat to its normal position.
CLEANING THE REFRIGERATOR
Cleaning the refrigerator is usually done after it is defrosted or put into storage. To clean the interior liner of
the refrigerator, use lukewarm weak soda solution. Use
only warm water to clean the finned evaporator, gasket,
ice tray and shelves.
NEVER use strong chemicals or abrasives to clean
these parts, as the protective surfaces will be damaged. It is important to always keep the refrigerator
clean.
SHUT- OFF (STORAGE PROCEDURE)
To shut off the refrigerator, turn the knob A to “OFF”
position. If the refrigerator will not be in operation for a
period of weeks, it should be emptied, defrosted, cleaned
and the doors left ajar. The ice trays should also be dried
and kept outside the cabinet.
! WARNING
DO NOT store explosive substances in the refrigerator, such as cigarette lighter gas, gasoline, ether
or the like.
NOTE: Sodium chromate is used for corrosion protec-
tion (less than 2 weight % of the coolant).
Ice making is accelerated if the thermostat knob B is
turned to the “MAX” setting.
It is a good idea to do this a few hours before the anticipated need for ice, but be sure to turn the thermostat
back to the normal setting when the ice is formed.
Food in the lower compartment may be frozen if the thermostat is left on “MAX”.
Total Refrigerated Volume 4 cu.ft.
DEFROSTING
Shut off the refrigerator by turning the knob A to “OFF”
position. Empty the refrigerator, leaving the drip tray under the finned evaporator, and the cabinet and freezer
doors open. Defrosting time can be reduced by filling
the ice trays with hot water and placing them in the
freezer compartment.
10
Page 11
MAINTENANCE & SERVICE
The user should be aware of service that must be
done on a regular schedule to keep the refrigerator
operating properly. The service should only be performed by a qualified technician who is familiar with
LP gas systems and refrigerators.
1. CARTRIDGE HEATER
The heat necessary for the operation of an absorption
cooling unit is supplied by an electric heater mounted in
a pocket of the boiler system.
Model RM 2452 is equipped with one electric heater for
120 volt AC.
Model RM 2453 is equipped with two electrical heaters,
one for 120 volt AC and one for 12 volt DC.
To replace the heater proceed as follows:
1. Before working on the refrigerator make sure that
120 volt AC and optional 12 volt DC leads are
disconnected. Shut off Gas valve.
2. Remove the terminal block cover, see FIG. 1.
3. Disconnect the heater leads.
4. With a pair of pliers unfold the lug holding the lid of
the boiler casing and open the lid.
5. Remove some insulation wool so that the heater is
accessible.
6. Turn and lift the heater out of its pocket.
7. Fit the new heater into the pocket.
8. Connect the leads and put on the terminal block
cover.
9. Reset the insulation and close the lid of the boiler.
2. REFRIGERATOR REMOVAL
Before working on the refrigerator, make sure the AC
voltage and DC voltage leads are disconnected. Shut
off the gas supply at the LP tank. Disconnect the gas
supply line at the rear of the refrigerator, see FIG. 1.
Always use a back up wrench when loosening and tightening connections.
Cap the gas supply line, loosen the screws anchoring
the refrigerator to the enclosure and slide the refrigerator out of the compartment.
When replacing the refrigerator make sure that the sealing strips are properly positioned.
Replacement is the reverse of removal. Check all connections for gas leaks.
Refer to section INSTALLATION, page 4 to 8.
3. PERIODIC MAINTENANCE
To keep your Dometic refrigerator operating efficiently
and safely, periodic inspection and cleaning of several
components once or twice a year is recommended.
A. It is important to keep the area at the back of the
refrigerator clean. Check the lower vent, upper vent
and area between these openings for any obstructions such as bird/insect nests, spider webs, etc.
Clean the coils on the back of the refrigerator. Use a
soft bristled brush to dust off the coils.
It is important to keep the refrigerator area free from
combustible material, gasoline and other flammable
vapors or liquids.
NOTE: The following maintenance is required once or
twice a year, but should only be done by a qualified serviceman who is familiar with LP gas systems and refrigerators.
B. Check all connections in the LP gas system (at the
back of the refrigerator) for gas leaks. The LP gas
supply must be turned on. Apply a non-corrosive
bubble solution to all LP gas connections.
The appearance of bubbles indicates a leak and
should be repaired immediately by a QUALIFIED
SERVICEMAN WHO IS FAMILIAR WITH GAS SYSTEM AND REFRIGERATORS.
! WARNING
DO NOT use a flame to check for gas leaks.
FIG. 12
GAS EQUIPMENT ASSEMBLY
MANUAL SHUT OFF VALVE
Shown in open position
Use a quarter dollar or a slotted screwdriver to change position
INLET FITTING
PRESSURE TEST PORT
BURNER JET.
NUT
THERMOCOUPLE
SPARK ELECTRODE
BURNER TUBE
BURNER MOUNTING SCREW
11
Page 12
C. The LP gas pressure should be checked and the main
regulator readjusted if pressure is incorrect. The correct operating pressure is 11 inches of water column.
The correct place to take the LP gas pressure is at
the test port just ahead of the burner jet. (See FIG. 12).
D. Inspect the flue baffle. It should be reasonably clean
and free of soot. Heavy soot formation indicates improper functioning of the burner. The flue and burner
both require cleaning in the following manner:
1. Unplug the refrigerator power cord from the 120-volt
AC outlet. (See FIG. 11).
2. Disconnect or shut off the 12 volt DC power to the
refrigerator.
3. Turn manual shutoff valve to OFF. (See FIG. 1 & 12).
4. Remove cover from the burner housing. (See FIG. 1).
5. Disconnect the wire from the high voltage electrode.
6. Remove the burner mounting screw and remove the
burner assembly. (See FIG. 12).
7. Remove the wire and flue baffle from the top of flue
tube. Clean the flue from the top using a flue brush.
Blowing compressed air into the flue will not properly
clean soot and scale out of the flue tube. Replace
the flue baffle.
8. Clean burner tube with a brush. Blow out burner with
compressed air.
9. Before removing burner jet, clean burner area of soot
and scale that fell out of flue tube. Remove the burner
jet. Soak the jet in wood alcohol and blow it out with
compressed air. Reinstall and tighten burner jet.
NOTE: The color of the flame shall be clear blue over
the slots of the burner. (See FIG. 13).
Clear blue color
of flame
FIG. 13
! WARNING
DO NOT use a wire or pin when cleaning the burner
jet as damage can occur to the precision opening.
This can cause damage to the refrigerator or create
a fire hazard.
10. Reinstall burner, being careful that the end of the
burner fits into the slot on the burner bracket. Check
to make sure slots are centered under the flue tube
and the thermocouple is positioned properly (tip of
thermocouple extends over two slots of burner).
11. Be sure to reconnect the wire to high voltage electrode. Check the electrode for proper location and
gap. (See FIG. 14).
FIG. 14
12. Turn on manual gas shutoff valve and check all fittings for leaks with soapy water.
13. Connect 120 volt power cord to the outlet and reconnect or turn on the 12 volt DC power.
14. Check LP gas safety shutoff. See page 7.
Electrode
1/8” to 3/16”
(3-5 mm)
Burner tube
4. TROUBLESHOOTING
Refrigerator Does Not Cool Properly
A. Burner jet clogged.
Clean. (See section Maintenance & Service, item 3.
Periodic maintenance, Paragraph D. item 1-14).
B. Check level of refrigerator.
C. Venting problem.
Restriction in air flow across cooling unit.
D. Heavy frost buildup on evaporator fins.
Defrost.
E. Flue baffle not inserted properly in flue tube.
F. Improperly set thermostat.
(See Operating Instructions, part Thermostat).
G. Burner dirty.
Clean. (See section Maintenance & Service, item 3.
Periodic Maintenance, Paragraph D. item 1-14).
H. LP gas pressure low at burner.
Set main regulator so pressure does not drop
below 11 inches of water column at pressure test
port. (See FIG. 12).
I. Burner not located properly under flue tube.
Relocate
J. Burner damaged.
Replace
K. Odor from fumes.
1. Dislocated burner
2. Damaged burner
3. Dirty flue tube
12
NOTE: AVOID SPRAYING WATER THROUGH THE
REFRIGERATOR VENTS WHILE WASHING YOUR RV.
All the above instructions are to be followed closely. The
refrigerator is quality-guaranteed. However, we are not
responsible for any failures caused by improper adjustments and unfavorable installation conditions. Contact
service point or distributor service dept. for assistance.
Page 13
CHANGING DOOR HINGES FROM ONE
SIDE TO THE OTHER
The refrigerator is equipped with a convertible door. To
change the door swing, consult the parts manual for the
Conversion Kit Number. For further information, please
contact Dometic Corporation listed on the front page.
INSTRUCTIONS FOR MOUNTING THE
DOOR PANEL
The refrigerator is normally delivered without door panel.
Before starting the mounting work, check that the panel
dimensions are in compliance with those given in the
table and the instructions are read thoroughly.
When mounting the panel, proceed as follows:
See figure page 14.
A. Open the door 90 degrees.
On new refrigerators, the decoration strip is taped
inside the door; if installed on the door, remove the
door decoration strip (2) by removing its three
screws (1).
B. Insert the vertical edges into the grooves of the
door frame (3).
C. Push the panel downward so that the lower hori-
zontal edge of the panel (4) is fitted into the bottom
groove (5).
D. Put the decoration strip across the door so that the
gap is covered.
Secure the decoration strip with the three screws
removed in Step A (1).
SP ARE P ARTS
The following list is a list of commonly used parts, which
should be available, if required, from your Dometic Service Center.
A = RM 2452; B = RM 2453
Part No. Description
17 37 71-01/5 A B Heater, 175W, 120V
17 37 39-06/1 - B Heater, 175W, 12V
200 74 19-16/7 A B Jet, No.43
293 03 79-00/9 A B Electrode
293 06 97-06/1 A B Burner
293 17 96-01/1 A B Piezo lighter
293 25 75-01/8 A B Door shelf, lower
293 25 76-01/6 A B Door shelf, 2 pieces
293 26 67-01/3 A B Baffle
293 26 70-01/7 A B Handle (light brown)
293 26 70-02/5 A B Handle (black)
293 27 50-02/5 A B Door reversing kit,
right-left (light brown)
293 27 50-03/3 A B Door reversing kit,
left-right (light brown)
293 27 50-13/2 A B Door reversing kit,
right-left (black)
293 27 50-14/0 A B Door reversing kit,
left-right (black)
PANEL DIMENSIONS
MAX. THICKNESS 5/32" (4 mm)
REFR. MODEL HEIGHT WIDTH
TYPE MAX. MIN. MAX. MIN.
RM 2452 mm 827 825 527 524
RM 2453
inch 32-9/16 32-1/2 20-3/4 20-5/8
Contact an authorized service center for
parts and repairs as needed.
13
Page 14
1
1
2
1
3
3
1
1
1
4
5
14
CERTIFIED VENT SYSTEM KITS
REFRIGERATOR KIT
MODEL NO. COMPONENTS PART NO.
RM 2452 3A Roof Base 3103633.XXX*
RM 2453 Roof Cover 3103634.XXX*
Lower Side Vent 3109350.XXX*
* Fill in “XXX” with color code numbers. For color codes, contact your supplier.
For further information contact your dealer or distributor.
Page 15
RM 2452
RM 2453
15
Page 16
16
MO-FO 0321
Loading...