RM2350
8251227-05
MO-M 0911
RA/RM-1D
).34!,,!4)/.
/0%2!4).'
).3425#4)/.3
FOR YOUR SAFETY
If you smell gas:
1. Open windows and door.
2. Don’t touch electrical switches.
3. Extinguish any open flame.
4. Turn off the gas supply at the source.
FOR YOUR SAFETY
Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of
this or any other appliance.
Improper installation, adjustment,
alteration, service or maintenance can
cause injury or property damage. Refer to
this manual. For assistance or additional
information consult a qualified installer,
service agency or the gas supplier.
7!2.).'
6
!
Contact a qualified person.
5.
.
2
INSTALLATION INSTRUCTIONS ____________ 3
GENERAL INFORMATION .........................3
PACKAGING ....................................3
VENTILATION REQUIREMENTS ....................3
CLEARANCES ..................................3
DIMENSIONS ...................................4
INSTALLING THE REFRIGERATOR .................4
SECURING THE REFRIGERATOR ..................4
CONNECTIONS .................................4
RE-HINGING THE DOOR .........................6
MOUNTING THE DOOR PANEL .....................6
REFRIGERATOR REMOVAL .......................6
OPERATING INSTRUCTIONS ______________ 7
GAS, AC AND DC OPERATION .....................7
REGULATING THE TEMPERATURE .................8
TURNING OFF THE REFRIGERATOR ................8
STORAGE COMPARTMENTS ......................8
PRODUCT CARE ................................9
MAINTENANCE & SERVICE _______________ 9
REPLACING THE HEATER ........................9
PERIODIC MAINTENANCE ........................9
TROUBLESHOOTING ...........................10
APPENDIX ____________________________ 11
REARVIEW EQUIPMENT .........................11
WIRING DIAGRAM ..............................11
CONTENTS INTRODUCTION
We are pleased that you have chosen this refrigerator and
hope you will derive much satisfaction from using it.
The refrigerator is designed for storage of foods and storage
of frozen foods and making ice.
The installation and servicing should only be carried out by
an authorized/qualified person.
It is important to read through these instructions carefully
before using the refrigerator. To ensure good refrigeration and
economical operation, the refrigerator must be installed and
used as described in these instructions.
Follow the instructions in this manual. The refrigerator is
quality guaranteed. However, we are not responsible for any
failures caused by improper adjustments and unfavourable installation conditions. Please contact service point or distributor service dept. for assistance.
DATA PLATE
Check the data plate, located inside the refrigerator, to ensure
that you have received the right model and that it is suitable
for the available gas supply and pressure.
The right gas pressure is . . . . . . . . . . . . . . . . . . 2.75 kPa
The right voltage is . . . . . . . . . . . . . . . . . . 230 - 240 volt
The right gas consumption is . . . . . . . . . . . . . . 1.05 MJ/h
The data plate contains e. g. the following details:
Model designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Since these details will be needed if you have to contact service personnel, it is a good idea to make a note of them here.
SYMBOLS
The following symbols are used throughout the manual:
Indicates a potentially hazardous
situation, which, if not avoided,
could result in death or serious
injury.
Indicates a potentially hazardous
situation, which, if not avoided,
may result in minor or moderate
injury.
Used without the safety alert
symbol indicates, a potentially
hazardous situation which, if not
avoided may result in property
damage.
Step-by-step instructions
CAUTION
!
WARNING
!
CAUTION
INSTALLATION INSTRUCTIONS
VENTILATION REQUIREMENTS
The installation shall be made in such a manner as to separate
the combustion system from the living space of the mobile
home or recreational vehicle. Proper installation requires one
lower fresh air intake and one upper exhaust vent.
We recommend fitting the Dometic ventilation system, which
is specially developed by Dometic for this purpose. The ven-
tilation kits must be installed and used without modification.
An opening toward the outside at floor level in the refrigera-
tor compartment must be provided for ventilation of heavierthan-air fuel gases. The lower vent of the recommended kits
is provided with proper size openings. The flow of combustion and ventilating air must not be obstructed.
The lower side vent provides an
ready serviceability of the burner
refrigerator. This should be cen
erator.
GENERAL INFORMATION
The installation, servicing and gas installation must be performed by an authorised/qualified person. The refrigerator
must be installed in accordance with the manufacturers in-
stallation instructions, local gas fitting regulations, municipal
building codes, electrical wiring regulations, AS5601.2 “Gas
Installations” and any other statutory regulations.
PACKAGING
The packaging of this appliance is design to withstand the
transportation from the factory to the point where it will be
installed in the recreational vehicle.
Before starting to install the appliance, please, make sure all
parts of the packaging have been removed, so there will not
be anything left that may come into contact with heat parts of
the appliance or obstruct the combustion exhaust gases or the
air movement around the cooling unit.
G
KK
L
M
adequate access opening for
control manifold of the
tred on the back of the refrig
and
-
CLEARANCES
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIAL
Top
G
0 mm
Side
K
Bottom
L
Rear
M
1
0 mm
0 mm
0 mm
25 mm
Ven on components are:
1 X TP (Includes 1 x Tee piece & 1 x extension)
extra extensions may be requ ired depen ding on the
height of refrigerator and vent height. Part number
TPX
AS1625 vent kit
TP Kit
TPX
Extension
If the lower grille is not at floor level where leaking gas can
escape,a 40 mm hole to the outside should be made in the
floor of the recess to drain any unburned gas to the outside.Fit
the hole with wire mesh and an angled plate to protect it from
stones,mud etc.
MINIMUM VENTILATION REQUIREMENTS
Optional ventilation hole
minimum 40 mm dia
1 X AS1625 vent kit
••
Notice: If the design of the vehicle does not allow
you to install the top exhaust vent directly above
the condenser of the refrigerator (what Dometic
recommends):
"Minimum top vent height is 746mm (top of
upper vent opening)”
Ventilation System (Not Included)
Recommended
top vent height
is no lower than
the top of the
cabinet.
Recommended
top vent height
is no lower than
top of the
cabinet.
4
CONNECTIONS
LP GAS CONNECTION
The gas installation and servicing must be carried out by an
authorised person and conform to all relevant local authorities.
The refrigerator is not designed for operation on town gas or
natural gas but for operation on universal LP gas, the pressure
of which must be 2,75 kPa. Check that this is stated on
the data plate. The gas supply system must incorporate an
approved gas pressure regulator to maintain a supply pressure
of 2,75 kPa.
OVERALL DIMENSIONS RECESS DIMENSIONS
Height AWidth BDepth CHeight HWidth WDepth
D
mm 766 556 577 756 521 542
Apply a sealing strip to the foremost floor
of the enclosure. The
sealing should provide a
complete isolation of the
appliance’s combustion
system from the vehicle
interior.
Note! Be careful not to damage the sealing strip when
the refrigerator is put in place.
SECURING THE REFRIGERATOR
Failure to follow the sequence in securing refrigerator in
enclosure can cause leakage between the frame and cabinet!
After the refrigerator is put in place, (insuring a combustion
seal at the front frame), the refrigerator is to be secured in the
enclosure with five screws (not included).
The screws have to be installed in the following order:
Four screws installed through the front frame. 1.
One screw installed in rear base. 2.
In the parts bag there are plugs to be snapped in
the front frame to cover the four screw heads.
INSTALLING THE REFRIGERATOR
It is essential that all maximum or minimum dimensions •
are strictly maintained, as the performance of the refrigerator is dependent on adequate flow of air over the rear of
the refrigerator. The refrigerator must be installed in a substantial enclosure and must be level, see “
DIMENSIONS”.
Note!• Do not install the appliance directly on carpeting.
Carpeting must be removed or protected by a metal or
wood panel beneath the appliance, which extends at least
full width and depth of the appliance.
The space between the storage cabinet and the top of the •
refrigerator should be blocked otherwise heat will become
trapped in this space, making the top of the refrigerator hot, thus reducing the efficiency of the unit. All areas
within the recess in which the refrigerator is installed must
be sealed:
Make sure that there is a complete seal between the front frame of the refrigerator and the top, sides and bottom of the enclosure. A length of sealing strip is applied
to the rear surface of the front frame for this purpose.
D
AH
weiv ediS
D
W
C
B
evoba morf weiV
2
1
DIMENSIONS
The following dimensions offer adequate space for service
and proper installation.
CAUTION
Check that the gas supplied to the refrigerator is at the
correct pressure.
UNIVERSAL
Loading...