DNP SnapLab SL620A Installation And Quick Start Manual

SnapLab SL620A

Installation and Quick Start Guide

Exclusively for DNP DS-Series™ Printers

Software v1.1.1

PN: DOC-U-SL620-DLND-01

Rev: 10.31.2018

2

SL620A

Installation and Quick Start Guide

Summary

Visit www.dnpphoto.com for the latest documentation, FAQs and more!

Summary ................................................................................................................. 2

Warnings Chapter 1 .............................................................................................. 3

Warning on power connection ............................................................................................................................ 3

Compliance Notices ............................................................................................................................................. 3

Installation Chapter 2 ........................................................................................... 5

Box content .......................................................................................................................................................... 5

Attaching the Topper to the DS620A printer ....................................................................................................... 6

Quick Start Chapter 3 .......................................................................................... 11

Starting SL620A ..................................................................................................................................................11

Change of software language by default ...........................................................................................................11

Make a print order .............................................................................................................................................13

Shutdown the SL620A ........................................................................................................................................15

Troubleshooting Chapter 4 ................................................................................... 16

3

SL620A

Installation and Quick Start Guide

Warnings Chapter

1

To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.

To avoid electrical shock, do not open the DS-T mini and DS-Printer covers. Refer servicing to qualified staff
only.

THIS EQUIPMENT MUST BE GROUNDED.

To disconnect the main power, unplug the AC IN connector.

Use a proper power cord for your local power supply.

1. Use the approved power cord (3-core mains lead)/appliance connector/plug with grounding-contacts that
conform to the safety regulations of each country, if applicable.

2. Use the power cord (3-core mains lead)/appliance connector/plug conforming to the proper ratings (Voltage,
Ampere).

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment under FCC rules.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:

� Reorient or relocate the receiving antenna.
� Increase the separation between the equipment and receiver.
� Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
� Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment is in direct contact with the body of the user under normal operating conditions. This transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.

Warning on power connection

Compliance Notices

4

SL620A

Installation and Quick Start Guide

Class B Equipment

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

� Reorient or relocate the receiving antenna.
� Increase the separation between the equipment and receiver.
� Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
� Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this device not expressly approved by DNP Photo Imaging could void the
user’s authority to operate the equipment.

This is a controlled document. To be sure you have the latest version of this procedure, compare this document
revision to the revision listed in the Document Control database. If you find this document is not current, discard
and get the latest version from the Document Control database.

Importer:

DNP PHOTO IMAGING EUROPE SAS

Le Raphael Paris Nord 2 22 Avenue de Nations BP 51077

Villepinte, 95948 ROISSY CH DE GAULLE CEDEX, FRANCE

Manufacturer:

Fit Engineering S.R.L.

c/o DNP Imagingcomm America Corporation

4524 Enterprise Drive NW

Concord, NC 28027 United States

If you want to dispose of this product, do not mix with general household waste. There is a separate
collection system for used electronics products in accordance with legislation under the WEEE
Directive. For details, please consult with your dealer.

5

SL620A

Installation and Quick Start Guide

Installation Chapter

2

The box contents:

Topper

Power cord

USB cable

Rear Bracket with 2 x M3 screws

Router holder

Side brackets 4 x M3 screws

Netgear Router

(This document)

Box content