D-LINK DWL661APE Instructions
Quick Installation Guide
Unied AC Concurrent Dual-Band
PoE Access Point
This document will guide you through the
basic installation process for your new
D-Link Unied Wireless Access Point.
DWL-6610APE
Documentation is also available
on the D-Link website
About This Guide
This installation guide provides basic
instructions for installing the DWL-6610APE
Unied AC Concurrent Dual-band PoE Access
ENGLISH
Point on your network. For additional information
about how to use the Access Point, please see
the User Manual, which is available on the CD
included in this package or from the D-Link
support website.
System Requirements
- CD-ROM drive
- Windows
- Ethernet port or installed Ethernet adapter
- Internet Explorer 7.0, Safari 5.0, Firefox 4.0, or
®
, Macintosh®, or Linux-based operating
system
higher
Unpacking the Product
Open the shipping carton and carefully unpack its
contents. Please consult the packing list located
in following information to make sure all items are
present and undamaged. If any item is missing
or damaged, please contact your local D-Link
reseller for replacement.
- DWL-6610APE Unied AC Concurrent
Dual-band PoE Access Point
- Power adapter*
- 4 dual-band antennas
- Mounting ring
- Console cable*
- CD-ROM
- Ceiling bracket (3 sets, sizes are 9/16", 14/16",
and 1 1/2")
*The power adapter is an optional accessory and not
included in the package in some regions. To power
the units use a D-Link PoE switch or the D-Link
DPE-101GI PoE injector.
*The console cable is an optional accessory and
not included in the package in Armenia, Azerbaijan,
Belarus, Georgia, Israel, Kaliningrad, Kazakhstan,
Kyrgyzstan, Latvia, Lithuania, Moldova, Mongolia,
Russia, Turkey, Turkmenistan, Ukraine, and
Uzbekistan. If a cable is required, please contact your
reseller to order it (Model: ACS-AP-CONSOLE).
2 D-Link DWL-6610APE Quick Install Guide
Optional Accessories
- PoE base unit (Model: DPE-101GI)
Note: These accessories are not included in
the package. If any of these items are required,
please contact your reseller to order it.
Hardware Overview
LEDs
Figure 1. DWL-6610APE LEDs
POWER – When the LED is lit up, the
LAN – When this LED is lit up, the
2.4GHz/5GHz – When the LED is lit up, the
Interfaces
Power receptor
access point is powered and
ready for use.
device’s Ethernet port is
connected to an active router or
switch. The light will blink when
there is trac going through the
port.
access point’s radio is enabled.
It will blink when there is wireless
trac.
Console port
LAN port (PoE)
Figure 2. DWL-6610APE Rear Panel
2.4GHz SMA
Connector
5GHz SMA
Connector
Power button
Reset button
(for power adapter)
Installation
Power on the Access Point
To power on the DWL-6610APE, you can use ONE
of the following methods:
1. Connect the supplied power adapter
OR
2. Plug one end of an Ethernet cable into the LAN
port of the DWL-6610APE and the other end into a
port on a PoE switch.
Congure the Access Point
To set up and manage the DWL-6610APE, use one
of the following methods:
• Manage the access point from the computer:
connect the access point and your computer
directly via a straight-through Ethernet cable.
DWL-6610APE
• Manage the access point from the computer
via the switch or router: connect the access
point and your computer to the same switch
or router.
DWL-6610APE
Switch or Router
• Manage the access point from the computer
via the Unied Wireless Switch or Wireless
Controller: connect the access point to a
Unied Wireless Switch or Wireless Controller.
Connect your computer to the same network
as that of the Unied Wireless Switch or
Wireless Controller.
Computer
Computer
2.4GHz SMA
Connector
5GHz SMA
Connector
Mounting Options
You can mount a DWL-6610APE access point on
any of the following types of surfaces:
- Solid surface wall or ceiling
- Tabletop
Cable Requirement
Use a CAT 5 cable with an even sheath.
The Ethernet ports on the DWL-6610APE access
point cannot accept a CAT 5 cable that has an
uneven sheath; the RJ-45 connector on the cable
will not t properly into the receptacle on the
access point.
Wall Installation Recommendations
If you plan to install the DWL-6610APE on a wall
or other vertical surfaces, orient the top of the
access point (the side with the LEDs) toward
the intended coverage area. The radio antennas
transmit through the top of the access point but
not through the bottom (where the bracket is).
Warning: The DWL-6610APE is designed
to receive PoE power only from an
802.3af-compliant source, or from a D-Linkapproved power injector. Connecting an access
point to a Power over Ethernet (PoE) device
that is not approved by D-Link can damage the
equipment.
Warning: This product is to be connected only to
PoE networks without routing to the outside plant.
The equipment power cord must be connected to
a socket-outlet earthling connection.
Avertissement: Le DWL-6610APE est conçu
pour recevoir de l’alimentation PoE uniquement
à partir d’une source compatible 802.3at ou d’un
adaptateur secteur approuvé par D-Link. La
connexion d’un point d’accès à un périphérique
Power over Ethernet(PoE) non approuvé par
D-Link peut endommager l’équipement.
Avertissement: Ce produit doit être
connecté uniquement aux réseaux PoE sans
acheminement vers l’installation externe. Le
cordon d’alimentation de l’équipement doit être
branché sur une prise de terre avec prise de
courant.
ENGLISH
DWL-6610APE
Unied Wireless Switch
or
Wireless Controller
Computer
D-Link DWL-6610APE Quick Install Guide 3
Mounting Using Anchor
Screws
Installation
ENGLISH
1. Place the plastic wall mounting ring on a wall
or ceiling.
2. Mark the points where you will insert the
screws. Take out the mounting ring.
3. Drill holes in the marked points and insert the
plastic wall anchors.
4. Use the supplied screws to attach the mounting
ring to the wall.
5. Plug the CAT 5 cable into the LAN port on the
access point.
6. To attach the access point to the mounting ring,
rst locate the right side of the access point
that has a small lock symbol on it, and make
sure to line up this side with the side of the
mounting ring that has Open - Lock written
on it.
7. Twist clockwise to lock the access point onto
the ring. The lock symbol on the access point
must point directly to the Close text on the
mounting ring.
4 D-Link DWL-6610APE Quick Install Guide
Mounting Using Ceiling
Bracket
Installation
1. Clip two ceiling brackets on the ceiling panels.
Make sure both bracket are parallel.
Ceiling crossbar
Ceiling bracket
2. Use the provided screws to attach the mounting
ring to the ceiling bracket.
3. Plug the CAT 5 cable into the LAN port on the
access point.
4. Placed the DWL-6610APE’s male bracket in
the mounting ring’s female bracket. Rotate the
product clockwise to lock it in position.
LAN
POWER
5GHz
2.4GHz
ENGLISH
D-Link DWL-6610APE Quick Install Guide 5
Regulatory Information
ErP Power Usage
This device is an Energy Related Product (ErP) with High Network Availability (HiNA), and automatically
switches to a power-saving Network Standby mode within 1 minute of no packets being transmitted. It
can also be turned o through a power switch to save energy when it is not needed.
Network Standby: 6.6287 watts
Switched O: 0.0565 watts
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Non-modications Statement:
Any changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
6 D-Link DWL-6610APE Quick Install Guide
RF Frequency Requirements
This device is for indoor use only when using all channels in the
5.150 GHz - 5.250 GHz, 5.250 GHz - 5.350 GHz, 5.470 GHz - 5.725 GHz, 5.725 GHz - 5.850 GHz
frequency range. High power radars are allocated as primary users of the
5.150 GHz - 5.250 GHz, 5.250 GHz - 5.350 GHz, 5.470 GHz - 5.725 GHz, 5.725 GHz - 5.850 GHz
bands. These radar stations can cause interference with and/or damage this device. This device will not
operate on channels which overlap the 5600-5650 MHz band.
It is restricted to indoor environments only.
IMPORTANT NOTICE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20 cm between the radiator and your
body.
Innovation, Science and Economic Development Canada (ISED)
Statement:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Innovation, Science and Economic Development Canada (ISED)
Statement:
This device complies with ISED licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems;
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à
l’intérieur an de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux;
D-Link DWL-6610APE Quick Install Guide 7
Loading...