D-Link DSL-2770L User Manual

Download

Version 1.0 | 01/16/2013

User Manual

ADSL2+ Gigabit Cloud Router N300

DSL-2770L

Preface

D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes.

Manual Revisions

Revision Date Description

1.0 January 16, 2013 • Initial release

Trademarks

D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.

iD-Link DSL-2770L User Manual

Table of Contents

Preface ................................................................................. i

Manual Revisions ........................................................................... i

Trademarks ...................................................................................... i

Product Overview .............................................................. 1

Package Contents ......................................................................... 1

System Requirements ................................................................. 2

Introduction ...................................................................................3

Features ............................................................................................4

Hardware Overview ..................................................................... 5

Back............................................................................................ 5

Front/Bottom .........................................................................6

Installation .........................................................................7

Before you Begin ...........................................................................7

Wireless Installation Considerations ......................................8

Setup Wizard (on Installation CD) ........................................... 9

Connecting the DSL-2770L .....................................................10

SharePort Mobile App (iOS, Android) .................................11

Web-based Conguration Utility ..........................................15

Internet Setup ......................................................................16

ADSL Interface ................................................................17

Setup Wizard....................................................................18

Ethernet/3G WAN Interface ........................................26

Static IP ..............................................................................27

Dynamic IP (DHCP) ........................................................28

PPPoE (Username/Password) ....................................29

PPTP ....................................................................................30

L2TP ....................................................................................31

3G ........................................................................................32

Wireless Settings .................................................................34

Wireless Connection Setup Wizard..........................35

Wi-Fi Protected Setup...................................................36

Manual Wireless Settings ............................................37

LAN Setup ..............................................................................40

Router Settings ...............................................................40

DHCP Server Settings (Optional) ..............................41

Add DHCP Reservation ................................................42

Time and Date ......................................................................43

IPv6 ..........................................................................................44

USB Services .........................................................................51

Disk Utility ........................................................................52

File Sharing .......................................................................53

Access Control .................................................................54

iTunes Server ...................................................................55

Download Assistant ......................................................56

Download Status ............................................................58

Web HDD ..........................................................................59

SharePort Mobile ................................................................60

mydlink Settings .................................................................61

Advanced ......................................................................................62

Virtual Server ........................................................................62

Application Rules ................................................................63

QoS Engine............................................................................64

Outbound Filters .................................................................66

iiD-Link DSL-2770L User Manual

Table of Contents

Inbound Filters.....................................................................67

Wireless Filter .......................................................................68

DNS Setup .............................................................................69

Firewall & DMZ .....................................................................70

Advanced Internet .............................................................71

Advanced Wireless .............................................................72

Advanced LAN .....................................................................73

Port Mapping .......................................................................74

SNMP Setup ..........................................................................75

Remote Management .......................................................76

Routing ...................................................................................77

IPv6 Firewall ..........................................................................78

Budget Quota .......................................................................79

Tools ................................................................................................80

Password ................................................................................80

Save/Restore Settings .......................................................81

Firmware Update ................................................................82

WPA/WPA2 ............................................................................93

WPS ..........................................................................................96

Windows Vista® ......................................................................... 100

WPA/WPA2 ......................................................................... 101

WPS/WCN 2.0 .................................................................... 103

Windows® XP ............................................................................. 104

WPA/WPA2 ......................................................................... 105

Troubleshooting ............................................................107

Wireless Basics ...............................................................111

What is Wireless? ...................................................................... 112

Tips ................................................................................................ 114

Wireless Modes ......................................................................... 115

Networking Basics .........................................................116

Check your IP address ............................................................ 116

Statically Assign an IP address ............................................ 117

Ping Test .................................................................................83

System Log ............................................................................84

Schedules ..............................................................................85

Status ..............................................................................................86

Device Info ............................................................................86

Routing Info ..........................................................................87

IPv6 Status .............................................................................88

Support ..........................................................................................89

D-Link SharePort .........................................................................90

Connect a Wireless Client to your Router ......................92

WPS Button ...................................................................................92

Windows® 7 ...................................................................................93

Technical Specications ................................................118

iiiD-Link DSL-2770L User Manual

Section 1 - Product Overview

DSL-2770L ADSL2+ Gigabit Cloud Router N300

Power Adapter

Ethernet Cable

Product Overview

Package Contents

Telephone Cable for connection to your DSL line

Quick Installation Guide

CD-ROM with Installation Wizard and User Manual

If any of the above items are missing, please contact your reseller.

Note: Using a power supply with a dierent voltage rating than the one included with the DSL-2770L may cause damage and will void the warranty for this product.

1D-Link DSL-2770L User Manual

Section 1 - Product Overview

Network Requirements

Web-based Conguration

Utility Requirements

System Requirements

• A subscription with an Internet Service Provider

• A computer with 802.11n, g, or b wireless or an available Ethernet port

Computer with the following:

• Windows®, Macintosh, or Linux-based operating system

• An installed Ethernet adapter

Browser Requirements:

• Internet Explorer 7 or higher

• Firefox 3.5 or higher

• Safari 4 or higher

• Chrome 8 or higher

Windows® Users: Make sure you have the latest version of Java installed. Visit www.java.com to download the latest version.

mydlink Requirements

• iPhone/iPad/iPod Touch (iOS 3.0 or higher)

• Android device (1.6 or higher)

• Computer with the following browser requirements:

• Internet Explorer 7 or higher

• Firefox 3 or higher

• Safari 5 or higher

• Chrome 5 or higher

iPhone, iPad, and iPod touch are registered trademarks of Apple Inc. Android is a trademark of Google, Inc.

2D-Link DSL-2770L User Manual

Section 1 - Product Overview

Introduction

The D-Link ADSL2+ Gigabit Cloud Router N300 (DSL-2770L) comes equipped with four Gigabit ports to provide speeds up to 10x faster than standard 10/100 ports. It also uses 802.11n technology that signicantly outperforms 802.11g devices. With the addition of Intelligent Quality of Service (QoS), data streams are separated which helps organize and prioritize your network trac so your video streaming, gaming, and VoIP calls run smoother over both your wired and wireless network.

The ADSL2+ Gigabit Cloud Router N300 is also mydlink-enabled, which gives you access to your home network no matter where you go. Now you can monitor and manage your home network right from your laptop, iPhone®, iPad®, or Android™ device. mydlink-enabled routers can be congured to send an email to keep you informed anywhere, anytime when new devices are connecting to your network or unwanted access is detected. Monitor in real-time websites that are being visited with recent browser history displayed on the mydlink™ Lite app – which is great for parents.

SharePort Mobile technology lets you take advantage of the USB 2.0 port found on the back of your DSL-2770L. Plug in a USB storage drive and you can use the SharePort Mobile app for iOS and Android to access les, stream videos, view photos, or listen to music on your laptop or mobile devices. Plug in a printer and you can use SharePort to share access to that printer with your entire network.

The DSL-2770L ADSL2+ Gigabit Cloud Router N300 provides incredible speeds, fast ports, cloud features, and terric security features. It also features an innovative design and easy installation options.

3D-Link DSL-2770L User Manual

Section 1 - Product Overview

• Fast Wireless Networking - The DSL-2770L provides up to a full 300 Mbps* wireless connection with other

802.11n wireless clients.

• Cloud Features - The DSL-2770L is mydlink-enabled so you can remotely access and mange your router from a mobile device. SharePort Mobile can be used to share les, stream videos, view photos, and play music, and SharePort lets you share a printer.

• Compatible with 802.11n/g/b Devices - The DSL-2770L is still fully compatible with the IEEE 802.11g and

802.11b standards, so it can connect with all your existing wireless devices.

• Advanced Firewall Features - The Web-based user interface displays a number of advanced network management features including:

• Content Filtering - Easily applied content ltering based on MAC Address, URL, and/or Domain Name.

• Filter Scheduling - These lters can be scheduled to be active on certain days or for a duration of hours or minutes.

• Secure Multiple/Concurrent Sessions - The DSL-2770L can pass through VPN sessions. It supports multiple and concurrent IPSec and PPTP sessions, so users behind the DSL-2770L can securely access corporate networks.

Features

• User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the DSL-2770L lets you control what information is accessible to those on the wireless network, whether from the Internet or from your company’s server. Congure your router to your specic settings within minutes.

* Maximum wireless signal rate derived from IEEE Standard 802.11b, 802.11g, and 802.11n specications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely aect wireless signal range.

4D-Link DSL-2770L User Manual

Section 1 - Product Overview

Hardware Overview

Back

1 Wi-Fi On/O Button Turns the wireless network on and o

2 Power Button Turns the DSL-2770L on and o.

3 USB Port Connects to a USB ash drive to share content , or connect it to a USB printer to share it on your network.

4 Gigabit LAN Ports (1-3) Connect to Ethernet devices such as computers, switches, storage (NAS) devices and game consoles.

5 Gigabit LAN/WAN Port (4)

6 DSL Port Connects to your DSL phone line.

7 Power Receptor Receptor for the supplied power adapter.

Connects to Ethernet devices, or to another modem or Internet connection when the WAN interface is enabled on the GUI. For more information, refer to “Internet Setup” on page 16.

5D-Link DSL-2770L User Manual

Section 1 - Product Overview

1 Status LEDs

2 WPS Button

Hardware Overview

Front/Bottom

• Power: Indicates the router is receiving power

• Internet: Indicates trac to and from the Internet

• DSL: Indicates activity on your DSL connection

• Wi-Fi (WLAN): Indicates activity on your wireless network

• LAN (1-4): Indicates activity by a connected device

• USB: Indicates activity on the USB port

Helps create a secure wireless connection to a device automatically. To connect a device using WPS, press the WPS button on your device, then press the WPS button on the router within 120 seconds.

3 Reset Button

Use an unfolded paperclip to press and hold the reset button for 6 seconds to reset all settings to their factory defaults.

Note: Resetting your router will delete all settings on it.

6D-Link DSL-2770L User Manual

Section 2 - Installation

Installation

This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage.

Before you Begin

• Please congure the router with the computer that was last connected directly to your modem.

• Make sure you disable or uninstall any PPPoE software such as WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet.

7D-Link DSL-2770L User Manual

Section 2 - Installation

Wireless Installation Considerations

The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:

1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum -

each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.

2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle

appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.

3. Building Materials make a dierence. A solid metal door or aluminum studs may have a negative eect on range.

Try to position access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (sh tanks), mirrors, le cabinets, brick, and concrete will degrade your wireless signal.

4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF

noise.

5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security

systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not in use.

8D-Link DSL-2770L User Manual

Section 3 - Conguration

Setup Wizard (on Installation CD)

The Installation CD included in your package has a Setup Wizard that guides you through the installation and conguration of your DSL-2770L.

Note: It is highly recommended that you use this Setup Wizard to install and congure your DSL-2770L.

1. Insert the Installation CD into your PC’s CD-ROM drive.

2. The Setup Wizard should start automatically. Follow the onscreen instructions to set up and congure your DSL-2770L.

Note: If the Setup Wizard does not start automatically, go to your CD in Windows and double-click the setup le to start the wizard.

9D-Link DSL-2770L User Manual

Section 2 - Installation

Connecting the DSL-2770L

1. Position your router close to your modem and a computer. Place the router in an open area of your intended work area for better wireless coverage.

2. Connect your DSL phone line to the DSL port.

3. Plug the included Ethernet cable into your PC’s Ethernet port. Plug the other end of the cable into one of the four LAN ports on the DSL-2770L.

DSL-2770L

4. Connect the supplied power adapter into the power receptor on the back of the router and then plug it into a power outlet or surge protector. Press the power button and verify that the power LED is lit. Allow 1 minute for the router to boot up.

To continue on to conguring the DSL-2770L, refer to “Web-based Conguration Utility” on page 15.

Connecting to another modem or Internet line: If you are connecting the DSL-2770L to another modem or a wired Internet connection, connect the Ethernet cable from your Internet source to port 4 on the DSL-2770L. Refer to “Ethernet/3G WAN Interface” on page 26 for setup details.

Connecting to a 3G USB adapter: If you are connecting a 3G USB adapter to use for your Internet connection, plug it into the USB port. Refer to “Ethernet/3G WAN Interface” on page 26 for setup details.

Modem

INTERNET

Computer

USB

WPS

INTERNET

POWER

10D-Link DSL-2770L User Manual

Section 3 - Conguration

SharePort Mobile App (iOS, Android)

The SharePort Mobile app will allow you to access les from a USB storage drive that is plugged into your router. You must enable le sharing from the Setup > Storage page (refer to page 60) for this app to work properly.

1. Plug your USB storage drive into the USB port.

Note: The DSL-2770L supports USB storage drives with up to one terabyte(1 TB) of

storage capacity.

USB port

2. Use your iOS or Android mobile device to scan the QR code to the right to download the SharePort Mobile app.

You can also search for the SharePort Mobile app directly in the iOS App Store or

Google Play.

3. From your iOS or Android mobile device, choose Settings.

Note: These steps are for the iOS version of the app. The Android version may dier slightly.

Settings

11D-Link DSL-2770L User Manual

Section 3 - Conguration

4. Click Wi-Fi, select the Wi-Fi Network Name (SSID) that you created during setup and then enter the default Wi-Fi password located on your Wi-Fi conguration note.

5. Once connected, tap on the SharePort Mobile icon.

6. The following screen will appear.

12D-Link DSL-2770L User Manual

Section 3 - Conguration

7. Tap on the Settings icon located on the right top corner of the screen. Tap Edit to enter your User Name and Password (the default username is admin and the password eld should be left blank). Once you nish, click Done to continue.

8. For the Movie section, click the movie icon to play your movie from your USB ash drive.

9. For the Music section, click the music icon to play your music from your USB ash drive.

13D-Link DSL-2770L User Manual

Section 3 - Conguration

10. For the Photo section, click the Photo icon to view your photos from your USB

ash drive.

11. For the Files section, click on the Files icon to view your les from your USB ash

drive.

12. For the Folder section, click the folder icon to view your folders

from your USB ash drive.

14D-Link DSL-2770L User Manual

Section 3 - Conguration

Web-based Conguration Utility

To access the conguration utility, open a web-browser such as Internet Explorer and enter http://dlinkrouter.local.

Windows and Mac users may also connect by typing the IP address of the router (http://192.168.1.1) in the address bar.

Enter your password. The password should be left blank by default.

15D-Link DSL-2770L User Manual

Section 3 - Conguration

Internet Setup

From this screen, you can set up various settings related to your Internet connection.

ADSL Interface

Ethernet/3G WAN

Interface

Click the Setup button to see and edit your ADSL settings.

Click this Setup button to see and edit the WAN settings if you are using a 3G USB adapter or are using port 4 as a WAN port. This allows you to use the DSL-2770L as a router for another modem or Internet connection.

16D-Link DSL-2770L User Manual

Section 3 - Conguration

ADSL Interface

If you clicked the Setup button for ADSL Interface, you will see the following settings. You can click the Setup Wizard button to use a step by step wizard that guides you through conguration of your ADSL settings. See the following pages for how to use the Setup Wizard. If you are not sure what settings to use, please contact your Internet Service Provider.

WAN Interface

My Internet

Connection Is:

Host Name:

The settings displayed in the middle will vary depending on what you select for the My Internet Connection Is setting. See the following pages for details.

Data

Encapsulation:

Country/ISP

Provider:

VPI Number:

Select the WAN interface to congure, and whether to enable or disable it.

Select the WAN connection type for your ISP. Based on which connection type you choose, dierent settings will be displayed below. These settings are described on the following pages after the Setup Wizard pages.

• Ethernet Over ATM(RFC1483 Bridged) with NAT

• IP over ATM(RFC 1483 Routed)

• PPP over Ethernet

• PPP over ATM

• RFC 1483 Bridged

Enter a host name to use for your connection.

Select VCMux or LLC based on your ISP’s recommended settings.

Selecting your country and ISP provider from the dropdown boxes will automatically ll in the VPI and VCI numbers for you.

Enter the VPI number specied by your ISP.

VCI Number:

Schedule type:

Multicast:

IGMP Snooping:

VLAN TAG:

Enter the VCI number specied by your ISP.

Select UBR, CBR, VBR, or GFR based on your ISP’s recommended settings.

You can set multicast mode to Auto, IGMP v1, IGMP v2, or IGMP v3.

You can enable the IGMP snooping function by checking this box.

You can enable and specify the VLAN TAG if required by your ISP.

17D-Link DSL-2770L User Manual

Section 3 - Conguration

Setup Wizard

This Wizard will help you set up an ADSL connection.

Click Next to continue.

Enter a password for your network and verify it in the box below, then click Next.

Select your time zone from the drop-down menu and click Next.

18D-Link DSL-2770L User Manual

Section 3 - Conguration

Select your Internet connection type from Ethernet Over ATM (RFC1483 Bridged) with NAT, IP over ATM(RFC 1483 Routed), PPP over Ethernet, PPP over ATM, and RFC 1483

Bridged. Click Next.

Congure some settings for your Internet Connection. See below for the description of each setting. Click Next when nished.

Data

Encapsulation:

Country:

ISP Provider:

VPI Number:

VCI Number:

MAC Address:

Enter a SSID name for your wireless network and click Next.

Select VCMux or LLC based on your ISP’s recommended settings.

Select your country.

Select your ISP provider from the dropdown boxes will automatically ll in the VPI and VCI numbers for you.

Enter the VPI number specied by your ISP.

Enter the VCI number specied by your ISP.

Click Clone to have your computer’s MAC number automatically input.

19D-Link DSL-2770L User Manual

Section 3 - Conguration

Select a security option for your network from WPA, WPA2, or none. Click Next.

Set a wireless security password for your network if you have selected a security option in the previous step. Click Next.

The Internet connection has now been established. Click Next to register for a mydlink account or click Connect to complete the setup.

20D-Link DSL-2770L User Manual

Section 3 - Conguration

Ethernet Over ATM(RFC1483 Bridged) with NAT

Address Mode

Primary/Secondary

DNS Server:

MAC Address:

MTU:

Enable NAT:

Select Static IP if your ISP assigned you an IP address, subnet mask, gateway, and DNS server address. In most cases, select Dynamic IP.

Enter the Primary and secondary DNS server IP addresses assigned by your ISP.

If your ISP requires you to enter a MAC address, ll it in here. You can click the Clone MAC button to enter your current computer’s MAC address.

If you experience connection issues, you may need to change the MTU setting for optimal performance with your specic ISP. 1500 is the default MTU.

Check this to enable the router to use NAT to assign IP addresses for your devices.

21D-Link DSL-2770L User Manual

Section 3 - Conguration

IP over ATM(RFC 1483 Routed)

Address Mode

Primary/Secondary

DNS Server:

MAC Address:

MTU:

Enable NAT:

Select Static IP if your ISP assigned you an IP address, subnet mask, gateway, and DNS server address. In most cases, select Dynamic IP.

Enter the Primary and secondary DNS server IP addresses assigned by your ISP.

If your ISP requires you to enter a MAC address, ll it in here. You can click the Clone MAC button to enter your current computer’s MAC address.

If you experience connection issues, you may need to change the MTU setting for optimal performance with your specic ISP. 1500 is the default MTU.

Check this to enable the router to use NAT to assign IP addresses for your devices.

22D-Link DSL-2770L User Manual

Section 3 - Conguration

PPP over Ethernet

IPv6 Dualstack:

Username:

Password/Verify

Password:

Service Name:

IP Address:

Primary/Secondary

DNS Server:

MAC Address:

MTU:

Enable NAT:

Check this box to enable IPv6/IPv4 dualstack.

Enter the username for your ADSL account.

Enter the password for your ADSL account, then type it again in the Verify Password box.

You can enter a name for your service here.

Enter the IP address assigned to you by your ISP.

Enter the Primary and secondary DNS server IP addresses assigned by your ISP.

If your ISP requires you to enter a MAC address, ll it in here. You can click the Clone MAC button to enter your current computer’s MAC address.

If you experience connection issues, you may need to change the MTU setting for optimal performance with your specic ISP. 1500 is the default MTU.

Check this to enable the router to use NAT to assign IP addresses for your devices.

23D-Link DSL-2770L User Manual

Section 3 - Conguration

PPP over ATM

Dualstack:

PPPoA Account:

PPPoA Password/

Verify PPPoA

Password:

Service Name:

IP Address:

Primary/Secondary

DNS Server:

MTU:

Enable NAT:

Check this box to enable IPv6/IPv4 dualstack.

Enter the username for your ADSL account.

Enter the password for your ADSL account, then type it again in the Verify PPPoA Password box.

You can enter a name for your service here.

Enter the IP address assigned to you by your ISP.

Enter the Primary and secondary DNS server IP addresses assigned by your ISP.

If you experience connection issues, you may need to change the MTU setting for optimal performance with your specic ISP. 1500 is the default MTU.

Check this to enable the router to use NAT to assign IP addresses for your devices.

24D-Link DSL-2770L User Manual

Section 3 - Conguration

There are no extra settings to congure when you choose this option. See the ADSL Interface page to congure the settings below.

RFC1483 Bridged

25D-Link DSL-2770L User Manual

Section 3 - Conguration

Ethernet/3G WAN Interface

If you clicked the Setup button for Ethernet/3G WAN Interface, you will see the following settings. You can click the Setup Wizard button to use a step-by-step wizard that guides you through conguration of your WAN settings. If you are not sure what settings to use, please contact your Internet Service Provider.

WAN Interface:

My Internet

Connection Is:

Host Name:

The settings displayed in the middle will vary depending on what you select for the My Internet Connection Is setting. See the following pages for details.

Multicast:

IGMP Snooping:

VLAN TAG:

Select the WAN interface to congure, and whether to enable or disable it.

Select Static IP, DHCP, PPoE, PPTP, L2TP, or 3G(through a USB adapter). Based on the setting you choose, the following settings will be dierent.

Enter a host name to use for your connection.

Select what multicast mode to use (Auto/IGMP v1/IGMP v2/IGMP v3), or if you want to disable it.

Check this box if you want to enable IGMP Snooping.

To set a VLAN tag, check this box, then enter the VLAN TAG to use.

26D-Link DSL-2770L User Manual

Section 3 - Conguration

Only use Static IP if directed to by your Internet Service Provider.

Static IP

My Internet

Connection:

IP Address:

Subnet Mask:

Default

Gateway:

Primary/

Secondary DNS

Server:

MAC Address:

MTU:

Enable NAT:

Select Static IP from the drop-down menu.

Enter the IP address assigned to you by your Internet Service Provider.

Enter the subnet mask assigned to you by your Internet Service Provider.

Enter the default gateway assigned to you by your Internet Service Provider.

Enter the Primary and secondary DNS server IP addresses assigned by your ISP. These addresses are usually obtained automatically from your ISP. Leave at 0.0.0.0 if you did not specically receive these from your ISP.

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1500 is the default MTU. Enter the ISP Service Name (optional).

Check this box if you want the router to use NAT to provide IP addresses for your computers and devices. If this is disabled, your devices will need to get IP addresses from your ISP or congured individually.

27D-Link DSL-2770L User Manual

Section 3 - Conguration

Dynamic IP (DHCP)

If you are unsure what method you use to connect to the Internet, try this rst. Cable modems usually use this type of connection

My Internet

Connection:

Primary/Secondary

DNS Server:

MAC Address:

MTU:

Enable NAT:

Select Dynamic IP (DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for cable modem services.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1500 is the default MTU.

28D-Link DSL-2770L User Manual

Section 3 - Conguration

PPPoE (Username/Password)

Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.

My Internet

Connection:

Username:

Password:

Service Name:

IP Address:

Primary/

Secondary DNS

Server:

MAC Address:

MTU:

Select PPPoE (Username/Password) from the drop-down menu.

Enter your PPPoE username.

Enter your PPPoE password and then retype the password in the next box.

Enter the ISP Service Name (optional).

Enter the IP address assigned to you by your Internet Service Provider.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1492 is the default MTU.

Enable NAT:

29D-Link DSL-2770L User Manual

Section 3 - Conguration

PPTP

Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.

My Internet

Connection:

Address Mode:

PPTP IP Address:

PPTP Subnet Mask:

PPTP Gateway IP

Address:

PPTP Server IP

Address:

Username:

Password:

Select PPTP (Username/Password) from the drop-down menu.

Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.

Enter the IP address assigned to you by your Internet Service Provider.

Enter the subnet mask assigned to you by your Internet Service Provider.

Enter the Gateway IP Address provided by your Internet Service Provider.

Enter the Server IP provided by your Internet Service Provider.

Enter your PPTP username.

Enter your PPTP password and then retype the password in the next box.

30D-Link DSL-2770L User Manual

Section 3 - Conguration

L2TP

Choose L2TP if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.

My Internet

Connection:

Address Mode:

L2TP IP Address:

L2TP Subnet Mask:

L2TP Gateway IP

Address:

L2TP Server IP

Address:

Username:

Password:

Select L2TP (Username/Password) from the drop-down menu.

Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.

Enter the IP address assigned to you by your Internet Service Provider.

Enter the subnet mask assigned to you by your Internet Service Provider.

Enter the Gateway IP Address provided by your Internet Service Provider.

Enter the Server IP provided by your Internet Service Provider.

Enter your L2TP username.

Enter your L2TP password and then retype the password in the next box.

31D-Link DSL-2770L User Manual

Section 3 - Conguration

These settings allow you to congure the router to share a mobile Internet connection from a connected 3G USB adapter.

Dial-Up Prole:

Country/

Telecom/3G

Network:

Prefer Service Type:

Username:

Password:

Dialed Number:

Authentication:

APN:

PIN Code:

Primary/Secondary

DNS Server:

Select whether to try and auto-detect your 3G settings, or to manually set them up. You can click the Auto-Detection button to try and autodetect your current settings.

If you selected Manual for Dial-Up Prole, you can enter your Country, Telecom, and 3G Network to automatically ll in some of the settings for you.

Select whether to use 3G Only Mode, 2G Only Mode, or use Auto Mode to automatically switch between the two.

Enter the username for your account (optional).

Enter the password for your account (optional).

Enter the dial number as given to you by your Internet Service Provider.

If you selected Manual for Dial-Up Profile, you can set your authentication to Auto, PAP, or CHAP authentication.

If you selected Manual for Dial-Up Prole, enter your APN here.

If you selected Manual for Dial-Up Prole, enter your PIN code here.

Keep Alive:

You can select whether you want to use a keep alive method to keep your connection active.

32D-Link DSL-2770L User Manual

Section 3 - Conguration

If you select Use Ping, enter the ping interval and address to ping.

If you select Use LCP Echo Request, enter the lcp echo interval and lcp failure limit.

Ping Test:

Enable NAT:

Country/ISP

Provider:

Checking this box will enable ping testing, and you can set the ping interval, address, and packet size using the corresponding text boxes.

You can select your country and Internet Service Provider to automatically ll in the necessary Multicast and IGMP Snooping settings.

33D-Link DSL-2770L User Manual

Section 3 - Conguration

Wireless Settings

If you want to congure the wireless settings on your router using a guided wizard, click Wireless Connection Setup Wizard.

Click Wi-Fi Protected Setup if you want to add a wireless device using Wi-Fi Protected Setup (WPS).

If you want to manually congure the wireless settings on your router, click Manual Wireless Connection Setup and refer to the next page.

34D-Link DSL-2770L User Manual

Section 3 - Conguration

Wireless Connection Setup Wizard

The Wireless Connection Setup Wizard is designed to guide you through a step-by-step process to congure your wireless network.

Type your desired wireless network name (SSID), then click Next.

Choose what level of wireless security you want to use. It is highly recommended that you select BEST. Click Next to continue.

Based on the level of wireless security you chose, you will need to enter a password for your wireless network. Click Next to continue.

Wireless setup is now complete. Click Save to save your settings and complete the setup process.

35D-Link DSL-2770L User Manual

Section 3 - Conguration

Wi-Fi Protected Setup

If you clicked on the Wi-Fi Protected Setup button on the Wireless Setup page, you will see this screen. The Wi-Fi Protected Setup page allows you to create a wireless connection between your router and a device automatically by simply pushing a button or entering a PIN code.

You can also use Windows 7 to do initial conguration of your router by using the Connect to a network wizard in Windows, and entering the WPS PIN/AP PIN of the router when prompted. After modifying any settings, click Save Settings to save your changes.

WPS:

AP PIN (also known

as WPS PIN):

Cong Mode:

Cong Status:

Cong Method:

WPS Status:

Select whether you would like to enable or disable WPS features.

If you use Windows 7’s Connect to a network wizard to do initial conguration of the router, you will need to enter the WPS PIN/AP PIN into the wizard when prompted. The factory default WPS PIN/AP PIN is printed on a label located on the bottom of the router. You can click the Generate New PIN button to change it to a randomly generated PIN.

Select whether the WPS cong mode should be set to Registrar or Enrollee. In most cases, this should be set to Registrar so that you can use WPS to connect new wireless clients.

If this is set to CONFIGURED, the router will be marked as “already congured” to computers that try to use WPS conguration, such as Windows 7’s Connect to a network wizard. You can click the Release button to change the status to UNCONFIGURED to allow for WPS conguration of the router.

If this is set to UNCONFIGURED, you can click the Set button to change the status to CONFIGURED to block WPS conguration of the router.

This lets you choose whether to use the Push Button connection method (PBC) or PIN method to connect to a wireless client when the Trigger button is clicked. If you choose the PIN method, you will need to enter an 8-digit PIN number that the wireless client need to use to connect to your router.

This will show the current WPS connection process status. Click the Trigger button to initiate a WPS connection.

36D-Link DSL-2770L User Manual

Section 3 - Conguration

Manual Wireless Settings

If you clicked Manual Wireless Network Setup on the Wireless Settings page, you will see this screen. Here, you can congure the wireless network settings of your router. After making your changes, click the Save Settings button.

Enable

Wireless:

Wireless

Network

Name (SSID):

Auto Channel

Scan:

Wireless

Channel:

802.11 Mode:

Transmission

Rate:

Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions.

Service Set Identier (SSID) is the name of your wireless network. Create a name for your wireless network using up to 32 characters. The SSID is case-sensitive.

The Auto Channel Scan setting can be selected to allow the DSL-2770L to choose the channel with the least amount of interference.

Indicates the channel setting for the DSL-2770L. By default the channel is set to 6. The Channel can be changed to t the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto Channel Scan, this option will be greyed out.

Select one of the following:

• B/G Mixed - Select if you are using both 802.11g and 802.11b wireless clients.

• N Only - Select only if all of your wireless clients are 802.11n.

• B/G/N Mixed - Select if you are using a mix of 802.11n, 802.11g,

and 802.11b wireless clients.

Select a transmission rate to use. It is recommended that you leave this at the default setting of Best.

Visibility

Status:

AP Isolation:

Select Invisible if you do not want the SSID of your wireless network to be broadcasted by the DSL-2770L. If Invisible is selected, the SSID of the DSL-2770L will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DSL-2770L in order to connect to it.

Enabling AP Isolation prevents wireless clients from being able to communicate with one another. This can be useful when providing an Internet connection for many wireless clients, but keeping their trac and devices private from other users.

37D-Link DSL-2770L User Manual

Section 3 - Conguration

Wireless Security

Mode:

If you select WEP as your Security Mode:

Authentication:

WEP Encryption:

Default WEP

WEP Key:

Here, you can select between None, WEP, WPA-Personal, and WPAEnterprise. Refer to the following pages for details on conguring the

dierent security modes. Please note that using WEP encryption will limit wireless use to 802.11g/b only, as it is incompatible with 802.11n.

Choose what Authentication type to use.

Select an encryption level and key length to use. This will also set the type and length of the key you will need to enter.

Select which WEP key should be used as default.

Key:

Enter the password(key) for your wireless network. You can use the dropdown box to choose whether you want to create a password using HEX or ASCII characters. It will need to match the requirements for the WEP Key Length as shown.

If you select WPA-Personal as your Security Mode:

WPA Mode:

Cipher Type:

Group Key

Update

Interval:

Pre-Shared

Select whether to use WPA, WPA2, or both WPA and WPA2 for your wireless network..

Choose whether to use TKIP, AES, or both TKIP and AES ciphers for your wireless network.

You can set the Group Key Update Interval here, if necessary.

Enter the password(key) for your wireless network.

Key:

38D-Link DSL-2770L User Manual

Section 3 - Conguration

If you select WPA-Enterprise as your Security Mode:

WPA Mode:

Cipher Type:

Group Key

Update Interval:

Authentication

TImeout:

RADIUS Server

IP Address:

RADIUS Server

Port:

RADIUS Server

Shared Secret:

Select whether to use WPA, WPA2, or both WPA and WPA2 for your wireless network.

Choose whether to use TKIP, AES, or both TKIP and AES ciphers for your wireless network.

You can set the Group Key Update Interval here, if necessary.

Enter the authentication timeout in seconds.

Enter your RADIUS server IP address.

Enter your RADIUS server port.

Enter your RADIUS server shared secret.

39D-Link DSL-2770L User Manual

Section 3 - Conguration

LAN Setup

This section will allow you to change the local network settings of the router and to congure the DHCP settings.

Router Settings

This section will allow you to congure the router settings.

Router IP Address:

Subnet Mask:

Enter the IP address of the router. The default IP address is 192.168.1.1.

If you change the IP address, once you click Save Settings, you will need to enter the new IP address in your browser to get back into the conguration utility.

Enter the Subnet Mask. The default subnet mask is 255.255.255.0.

40D-Link DSL-2770L User Manual

Section 3 - Conguration

DHCP Server Settings (Optional)

DHCP stands for Dynamic Host Control Protocol. The DSL-2770L has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DSL-2770L. The DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool.

Enable DHCP

Server:

DHCP IP Address

Range:

DHCP Lease Time:

DHCP Relay:

DHCP Server IP

Address:

Check this box to enable the DHCP server on your router. Uncheck to disable this function.

Enter the starting and ending IP addresses for the DHCP server’s IP assignment.

Note: If you statically (manually) assign IP addresses to your computers or devices, make sure the IP addresses are outside of this range or you may have an IP conict.

The length of time for the IP address lease. Enter the Lease time in minutes.

Check the box to allow the DSL-2770L to act as a DHCP relay.

If DHCP Relay is enabled, enter the IP address of the DHCP server to relay.

41D-Link DSL-2770L User Manual

Section 3 - Conguration

Add DHCP Reservation

If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device.

Note: This IP address must be within the DHCP IP Address Range.

DHCP

Reservations List:

Enable:

IP Address:

MAC Address:

Dynamic DHCP

Clients:

Displays any reservation entries. Displays the host name (name of your computer or device), MAC Address, and IP address.

Click Add to create a new DHCP reservation. Select an existing reservation and click Edit to change its settings, or click Delete to remove the reservation.

After clicking Add or Edit, the following settings are available:

Enter the IP address you want to assign to the computer or device. This IP Address must be within the DHCP IP Address Range.

Enter the MAC address of the computer or device. If you want to assign an IP address to the computer you are currently on, click the Clone button to automatically ll in the MAC address.

Displays a list of clients currently using dynamic DHCP and their names, MAC addresses, IP addresses, and reservation time remaining.

42D-Link DSL-2770L User Manual

Section 3 - Conguration

Time and Date

The Time Conguration option allows you to congure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be congured to automatically adjust the time when needed.

Automatically

synchronize with

Internet time

server:

NTP Server Used:

Current Router

Time:

Time Zone:

Enable Daylight

Saving:

Date and Time:

When enabled, the router will automatically update its time by using an Internet time server. Alternatively, you can disable this option and manually set the time.

Enter the IP address of a NTP server or select one from the drop-down menu.

Displays the current date and time of the router.

Select your Time Zone from the drop-down menu.

To select Daylight Saving time manually, select enabled or disabled, and enter a start date and an end date for daylight saving time.

If Automatically synchronize with Internet time server is disabled, You can manually input the time. Enter the values in these elds for the Year, Month, Day, Hour, Minute, and Second and then click Set Time.

You can also click Copy Your Computer’s Time Settings to sync the date and time with the computer you are currently on.

43D-Link DSL-2770L User Manual

Section 3 - Conguration

IPv6

On this page, you can congure the IPv6 Connection type and settings.

IPv6:

IPv6 Connection:

Enable or disable IPv6 for your router.

If you wish to use IPv6, choose your IPv6 connection type:

• Static IPv6

• DHCPv6

• PPPoE

• 6 to 4

• IPv6 in IPv4 Tunnel

• PPPoA

Based on the connection type you choose, the following settings will change. Refer to the following pages for more details.

44D-Link DSL-2770L User Manual

Section 3 - Conguration

Static IPv6

IPv6 Address:

Subnet Prex

Length:

Default Gateway:

Primary/

Secondary DNS

Address:

LAN IPv6 Address:

LAN Link-Local

Address:

Autoconguration:

Autoconguration

Type:

Router

Lifetime:

Enter the address settings supplied by your Internet provider (ISP).

Enter a subnet prex length.

Enter the default gateway for your IPv6 connection.

Enter the primary and secondary DNS server addresses.

Enter the LAN (local) IPv6 address for the router.

Displays the router’s LAN Link-Local Address.

Enable or disable the autoconguration feature.

Choose either Stateless or Stateful(DHCPv6) from the drop-down menu.

Enter the IPv6 Address Lifetime (in minutes).

45D-Link DSL-2770L User Manual

Section 3 - Conguration

DHCPv6

Primary/Secondary

DNS Address:

LAN IPv6 Address:

LAN Link-Local

Address:

Autoconguration:

Autoconguration

Type:

Router

Lifetime:Link-Local

Address:

Enter the primary and secondary DNS server addresses.

Enter the LAN (local) IPv6 address for the router.

Displays the router’s LAN Link-Local Address.

Enable or disable the autoconguration feature.

Choose either Stateless or Stateful(DHCPv6) from the drop-down menu.

Enter the IPv6 Address Lifetime (in minutes).

46D-Link DSL-2770L User Manual

Section 3 - Conguration

PPPoE

Username:

Password:

Service Name:

MTU:

LAN IPv6 Address:

LAN Link-Local

Address:

Autoconguration:

Autoconguration

Type:

Router

Lifetime:Link-Local

Address:

Enter your PPPoE user name.

Enter your PPPoE password.

Enter the ISP Service Name.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1492 is the default MTU.

Enter the LAN (local) IPv6 address for the router.

Displays the router’s LAN Link-Local Address.

Enable or disable the autoconguration feature.

Choose either Stateless or Stateful(DHCPv6) from the drop-down menu.

Enter the IPv6 Address Lifetime (in minutes).

47D-Link DSL-2770L User Manual

Section 3 - Conguration

6 to 4

6 to 4 Address:

Primary/Secondary

DNS Address:

LAN IPv6 Address:

LAN Link-Local

Address:

Autoconguration:

Autoconguration

Type:

Router

Lifetime:Link-Local

Address:

Your 6 to 4 address will be shown here.

Enter the primary and secondary DNS server addresses.

Enter the LAN (local) IPv6 address for the router.

Displays the router’s LAN Link-Local Address.

Enable or disable the autoconguration feature.

Choose either Stateless or Stateful(DHCPv6) from the drop-down menu.

Enter the IPv6 Address Lifetime (in minutes).

48D-Link DSL-2770L User Manual

Section 3 - Conguration

IPv6 in IPv4 Tunneling

Remote IPv4

Address:

Local IPv4 Address:

Local IPv6 Address:

Primary/Secondary

DNS Address:

LAN IPv6 Address:

LAN Link-Local

Address:

Autoconguration:

Autoconguration

Type:

Router

Lifetime:

Enter the IPv4 remote address you will use.

Enter the IPv4 local address you will use.

Enter the IPv6 local address you will use.

Enter the primary and secondary DNS server addresses.

Enter the LAN (local) IPv6 address for the router.

Displays the router’s LAN Link-Local Address.

Enable or disable the autoconguration feature.

Choose either Stateless or Stateful(DHCPv6) from the drop-down menu.

Enter the IPv6 Address Lifetime (in minutes).

49D-Link DSL-2770L User Manual

Section 3 - Conguration

PPPoA

Username:

Password:

Service Name:

MTU:

LAN IPv6 Address:

LAN Link-Local

Address:

Autoconguration:

Autoconguration

Type:

Router

Lifetime:

Enter your PPPoA user name.

Enter your PPPoA password.

Enter the ISP Service Name.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1492 is the default MTU.

Enter the LAN (local) IPv6 address for the router.

Displays the router’s LAN Link-Local Address.

Enable or disable the autoconguration feature.

Choose either Stateless or Stateful(DHCPv6) from the drop-down menu.

Enter the IPv6 Address Lifetime (in minutes).

50D-Link DSL-2770L User Manual

Section 3 - Conguration

USB Services

From this screen, you can set up various settings related to sharing les on a USB storage drive plugged into the DSL-2770L.

Disk Utility:

File Sharing:

Access Control:

iTunes Server:

Download

Assistant:

Download Status:

Web HDD:

Click the Disk Utility button for settings on formatting and checking a connected USB storage drive, and to view its current usage and capacity.

Click the File Sharing button for settings used for sharing a connected USB storage drive on your network through SAMBA.

Click the Access Control button for settings on creating and modifying user accounts to control le access to the attached USB storage drive.

Click the iTunes Server button for settings for the iTunes server function of the DSL-2770L.

Click the Download Assistant button to add new automated download tasks.

Click the Download Status button to manage your download tasks.

Click the Web HDD button to access and manage les stored on your USB storage drive through your web browser.

51D-Link DSL-2770L User Manual

Section 3 - Conguration

Disk Utility

If you click Disk Utility on the NAS page, these settings will appear. Here, you can format and check a connected USB storage drive, and view its current usage and capacity.

Format This

Partition:

Check This

Partition:

Disk Total

Capacity:

Click this button to format the attached USB storage drive and prepare it for use. The drive will be formatted using the EXT3 le system.

Warning: Formatting your drive will delete all les and folders stored on it.

This will check the drive for errors. Please note that the drive must use the EXT3 le system in order to be checked.

This shows the full capacity of the USB storage drive.

52D-Link DSL-2770L User Manual

Section 3 - Conguration

File Sharing

If you click File Sharing on the NAS page, these settings will appear. Here you can adjust the settings for sharing your USB storage over a network through SAMBA. If you click the FTP Service Conguration button, you can adjust the FTP server settings.

Computer Name:

WorkGroup:

Server Comment:

FTP:

FTP Port:

FTP Max

Connection per IP:

FTP MAX Clients:

Client Support

UTF8:

Enter the name used to identify the USB drive on the network.

Enter the network workgroup to join for the USB drive.

Enter a comment to identify the USB drive on the network.

Select whether you want to enable or disable the FTP server function.

Set the port you want to use for the FTP server.

Set the maximum allowable connections per IP.

Set the maximum number of clients allowed to connect to the FTP server at one time.

Select whether to support Unicode.

Codepage:

Select which language to use for the FTP server.

53D-Link DSL-2770L User Manual

Section 3 - Conguration

Access Control

If you click Access Control on the NAS page, these settings will appear. Here you can adjust the settings for sharing your USB storage over a network through SAMBA.

Security Level:

Username/

Password:

Selecting Guest mode will allow all users to access les on the USB storage drive. Selecting Authorization mode will require users to enter a username and password in order to access les on the USB drive.

To set up user accounts for Authorization mode, click the User Conguration button.

After clicking the User Conguration button, these settings will appear:

Enter a Username and Password for an account and click the Add button to create a new user.

You can also select an existing user and click Delete to remove it.

54D-Link DSL-2770L User Manual

Section 3 - Conguration

iTunes Server

If you click iTunes Server on the NAS page, these settings will appear. Here you can adjust the settings for the iTunes server function.

Service:

Service Name:

Service Port:

Access Password:

Select whether to enable or disable the iTunes server feature.

Enter a name to identify your iTunes server.

Enter which port to use for the service.

If you wish to protect access your les with a password, enter it here.

55D-Link DSL-2770L User Manual

Section 3 - Conguration

Download Assistant

If you click Download Assistant on the NAS page, these settings will appear. Here you can set up download tasks for the DSL-2770L to run and download to the USB storage.

Download Type:

Job Name:

URL:

Save To:

Username/

Password:

Start Time:

Download Type:

Select which type of download you want to add. If you select FTP, you will see these settings.

Enter a name to identify the download job.

Enter the full FTP address and port of the le you want to download.

Enter the path you want to save the le to.

Select whether to connect to the FTP server anonymously or to use a login account.

If you select Account for your Login Method, enter the username and password for the FTP account.

You can choose to start the download task immediately by selecting At Once, or you can select Schedule and select a date and time to start the download task.

If you select HTTP, you will see these settings.

Job Name:

URL:

Save To:

Start Time:

Enter a name to identify the download job.

Enter the full FTP address and port of the le you want to download.

Enter the path you want to save the le to.

You can choose to start the download task immediately by selecting At Once, or you can select Schedule and select a date and time to start the download task.

56D-Link DSL-2770L User Manual

Section 3 - Conguration

Clicking the E-mail Alert Conguration button shows these settings:

HTTP/FTP

download alert:

SMTP Server

Address:

SMTP Server Port:

SMTP UserName/

Password:

Email Address:

Email Subject:

Select whether you want to enable e-mail alerts when a le is transferred over HTTP/FTP.

Enter the SMTP address of the e-mail account you want to send notications from.

Enter the SMTP port of the e-mail account you want to send notications from.

Enter the username and password for the e-mail account you want to send notications from.

Enter the e-mail address you want your notications to be sent to.

Enter the subject to use for your e-mail notications.

57D-Link DSL-2770L User Manual

Section 3 - Conguration

Download Status

If you click Download Status on the NAS page, these settings will appear. Here you can view and manage the download tasks of the DSL-2770L. After selecting a task, you can click Pause/Resume to pause and resume a download, or you can click Start Now to start the download task.

58D-Link DSL-2770L User Manual

Section 3 - Conguration

Web HDD

If you click Web HDD on the NAS page, you can see the folders and les stored on your USB drive. Click on a folder to open it, or click the Back button to up a directory. Click Upload to upload a le to the current folder, or click a le to select it, then click Download to download the le to your computer, or click Delete to delete it from the storage drive. Click the Add Folder button and enter a folder name to create a new folder in the current folder.

59D-Link DSL-2770L User Manual

Section 3 - Conguration

SharePort Mobile

This page will allow you to set up access to les on an external USB storage drive1 that is plugged into the router. You can do this through local network or from the Internet using either a web browser or an app on your smartphone or tablet. You can create users that can be allowed access to these les through SharePort Mobile services accessible through a web UI or on mobile devices using the SharePort Mobile app available for iOS and Android.

Enable SharePort

Web Access

HTTP Access Port:

Allow Remote

Access:

User Creation:

User List:

Number of Devices:

SharePort Web

Access Link:

Check this box if you wish to be able to access SharePort through a browser as well as the mobile app.

Enter the port you want to use when accessing SharePort using a web browser.

Check this box if you wish to be able to access SharePort through a web browser over the Internet.

To give a new user access to your SharePort storage, enter a User Name and Password here. You can Add new users or choose existing users from the drop-down menu if you wish to Edit or Delete them.

Note: The Admin password is the same as the admin password for the router. The Guest password is guest and cannot be changed.

This list displays all of the users with access to the SharePort Mobile content, what they can access, and their Read/Write Permissions. Click on the edit icon at the right to change home folder and access rights for the user.

All devices you have set up for SharePort access will be listed here.

This area will display the links to connect to your SharePort drive through a web browser from a device on your network.

Supports capacities of up to 1 TB for USB storage drives.

60D-Link DSL-2770L User Manual

Section 3 - Conguration

mydlink Settings

Devices that are mydlink-enabled can be accessed and managed through the mydlink website and by using mydlink mobile apps for iOS and Android. You cannot take advantage of these features without a mydlink account. If you have a mydlink account already, you can log in when you rst set up the router, or by visitng this setup page.

mydlink Service:

Service:

Displays whether your device is registered with a mydlink account or not.

Click to go to open a wizard that will guide you through the process of registering your device to your mydlink account. If you don’t have a mydlink account yet, you will be able to create one.

61D-Link DSL-2770L User Manual

Section 3 - Conguration

Advanced

Virtual Server

This will allow you to forward a single port or a range of ports to a specic PC or device on your network.

You can automatically ll information required for some commonly used services by using the Well known services dropdown box at the top, selecting a rule ID to copy the information to, selecting a schedule rule if desired, then clicking the Copy to button.

Service Ports:

Server IP : Port:

Enable:

Schedule Rule#:

Enter the external port(s) that you want to forward.

Enter the IP address and ports of the computer on your local network that you want to forward the specied (external) Service Ports to.

You can enter a single port or a range of ports. Separate ports with a common. Example: 24,1009,3000-4000

Check this box to enable the rule.

Enter the schedule rule number that you want to apply to this port forwarding rule. You can create a new schedule by clicking the Add New Rule... button, or you can leave it blank to allow the rule to be always on.

For more details on creating schedule rules, refer to “Schedules” on page 85

62D-Link DSL-2770L User Manual

Section 3 - Conguration

Application Rules

Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have diculties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DSL-2770L. If you need to run applications that require multiple connections, specify the port normally associated with an application in the “Trigger Port” eld, select the protocol type as TCP or UDP, then enter the rewall (public) ports associated with the trigger port to open them for inbound trac.

You can automatically ll information required for some commonly used services by using the Popular applications dropdown box at the top, selecting a rule ID to copy the information to, then clicking the Copy to button.

Trigger:

Incoming Ports:

Enable:

This is the port used to trigger the application. It can be either a single port or a range of ports.

This is the port number on the Internet side that will be used to access the application. You may dene a single port or a range of ports. You can use a comma to add multiple ports or port ranges.

Check this box to enable the rule.

63D-Link DSL-2770L User Manual

Section 3 - Conguration

QoS Engine

The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classied automatically.

QoS:

WAN Interface:

Bandwidth of

Upstream:

Bandwidth of Downstream:

WMM(Wi-Fi

Multimedia)

Wireless QoS:

LAN QoS:

QoS Rules Table:

This option is disabled by default. Enable this option for better performance and experience with online games and other interactive applications, such as VoIP.

Select which WAN interface to adjust the QoS settings for.

Enter the upstream bandwidth for your Internet connection.

Enter the downstream bandwidth for your Internet Connection

Select whether you wish to enable the WMM feature, then click the Apply WMM Settings button.

Click on this button to add a Wireless QoS rule.

Click on this button to add a LAN QoS rule.

This shows a list of your current QoS rules. You can check or uncheck a rule to enable or disable it, or you can click on the X next to the rule to delete it.

64D-Link DSL-2770L User Manual

Section 3 - Conguration

If you clicked on Wireless QoS or LAN QoS, you will see these settings. If you want to create a compound rule(for TCPPORT, UDPPORT, or TOS only), click the Add A Conjunction (AND) Rule button.

Rule:

Class/Class Info:

Function/Function

data:

Check the box if you want the rule to be enabled.

Select what criteria the rule should apply to, and enter the relevant criteria in the Class Info text box.

• IP: IP address

• TCPPORT: TCP port

• UDPPORT: UDP port

• MAC: MAC address

• DSCP: DSCP name

• TOS: Type of service

Based on the Class selected, enter what you want the rule to apply to and enter the relevant information in the Function data text box. For example, for TCPPORT, you should enter the TCP port the rule should apply to.

• PRI: Set priority level

• MAXR: Set maximum bandwidth rate

• MINR: Set minimum bandwidth rate

• SESSION: Set connection session

• DROP: Drop the packet

• LOG: Log the event

• ALERT: Create an alert event

Direction:

Set which trac direction the rule should apply to.

65D-Link DSL-2770L User Manual

Section 3 - Conguration

Outbound Filters

The Outbound Filter option is an advanced method of controlling data sent out to the Internet. With this feature you can congure outbound data ltering rules that control data based on an IP address range. Select whether to Allow all trac specied by your rules to pass, or to Deny all trac specied by your rules.

Source IP:Ports:

Destination

IP:Ports:

Enable:

Schedule Rule#:

Enter the starting IP address and ports from your network. Enter 0.0.0.0 if you do not want to specify an IP range.

Enter the ending IP address and ports outside your network. Enter

255.255.255.255 if you do not want to specify and IP range.

Check this box to enable the rule.

For more details on creating schedule rules, refer to “Schedules” on page 85

66D-Link DSL-2770L User Manual

Section 3 - Conguration

Inbound Filters

The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can congure inbound data ltering rules that control data based on an IP address range. Select whether to Allow all trac specied by your rules to pass, or to Deny all trac specied by your rules.

Source IP:Ports:

Destination

IP:Ports:

Enable:

Schedule Rule#:

Enter the starting IP address and ports from outside your network. Enter

0.0.0.0 if you do not want to specify an IP range.

Enter the ending IP address and ports inside your network. Enter

255.255.255.255 if you do not want to specify and IP range.

Check this box to enable the rule.

For more details on creating schedule rules, refer to “Schedules” on page 85

67D-Link DSL-2770L User Manual

Section 3 - Conguration

Wireless Filter

The Wireless Filter feature allows you to limit wireless access to your network based on a device’s MAC address.

Enable Wireless

Mac Filtering:

Filter Name:

Wireless MAC

Address:

Check this box to enable wireless ltering by MAC address. Select whether to Allow access to all computers specied, or to Deny access to all computers specied.

Enter a name for the lter rule.

Enter the MAC address of the wireless device you want to lter.

Click the Add/Apply button to save your changes and apply your settings.

68D-Link DSL-2770L User Manual

Section 3 - Conguration

DNS Setup

The DDNS feature allows you to host a server (Web, FTP, or Game Server) using a domain name that you have purchased (such as www.exampledomain.com) with your dynamically assigned IP address. You can use one of the listed DDNS service, or you can sign up for D-Link’s free DDNS service at www.dlinkddns.com. After modifying any settings, click Save Settings to save your changes.

DDNS:

Provider:

Host Name:

Username / E-mail:

Password / Key:

Tick this checkbox to enable the DDNS feature.

Select a DDNS service provider to use.

Enter the Host Name that you registered with your DDNS service provider.

Enter the Username for your DDNS account.

Enter the Password for your DDNS account.

69D-Link DSL-2770L User Manual

Section 3 - Conguration

Firewall & DMZ

A rewall protects your network from the outside world. The DSL-2770L oers a rewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.

Enable SPI:

Enable DMZ:

DMZ IP Address:

SPI (Stateful Packet Inspection, also known as dynamic packet ltering) helps to prevent cyber attacks by tracking more state per session. It validates that the trac passing through the session conforms to the protocol.

If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer.

Note: Placing a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort.

Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication. If this computer obtains it’s IP address automatically using DHCP, be sure to make a static reservation on the Setup > Network Settings page so that the IP address of the DMZ machine does not change.

70D-Link DSL-2770L User Manual

Section 3 - Conguration

Advanced Internet

This screen lets you add or remove PVC settings and select your ADSL mode. It is recommended that you only change settings on this page as directed by your service provider.

Multiple PVC

Settings:

Advanced ADSL

Settings:

This shows you your current PVC settings. You can click the Add button to add a new PVC setting, click the Edit button for a PVC setting to edit it, or tick the checkbox next to a setting and click Delete to remove it.

Select which ADSL mode to use.

71D-Link DSL-2770L User Manual

Section 3 - Conguration

Advanced Wireless

This page allows you to change some of the advanced wireless settings of the DSL-2770L. It is recommended that you only change these settings if you are familiar with their functions and proper settings, or are instructed to do so.

Beacon Interval:

Transmit Power:

RTS Threshold:

Fragmentation:

DTIM Interval:

WMM Capable:

TX Rates:

Specify a value for the beacon interval. Beacons are packets sent by an Access Point to synchronize a wireless network. 100 is the default setting and is recommended.

Set the transmit power of the antennas.

This value should remain at its default setting of 2347. If inconsistent data ow is a problem, only a minor modication should be made.

The fragmentation threshold, which is specied in bytes, determines whether packets will be fragmented. Packets exceeding the 2346 byte setting will be fragmented before transmission. 2346 is the default setting.

Set the interval for DTIM. A Delivery Trac Indication Message (DTIM) is a countdown informing clients of the next window for listening to broadcast and multicast messages. The default interval is 3.

WMM (Wi-Fi Multimedia) is a QoS (Quality of Service) system for your wireless network. Enable this option to improve the quality of video and voice applications for your wireless clients.

Select the basic transfer rates based on the speed of wireless adapters on your wireless network. It is strongly recommended to keep this setting to Auto.

Guest Wireless

Settings:

Here, you can set up a Wireless Guest Network, which will provide access to the Internet, but not to your network devices. To use this feature, tick the Enable Wireless Guest Network checkbox. For more details, refer to “Wireless Settings” on page 34.

72D-Link DSL-2770L User Manual

Section 3 - Conguration

Advanced LAN

Advanced LAN contains settings which can change the way the router handles certain types of trac. We recommend that you do not change any of these settings unless you are already familiar with them or have been instructed to make the change by one of our support personnel. After modifying any settings, click Save Settings to save your changes.

Enable UPnP:

Enable WAN Ping

Respond:

Tick this checkbox to use the Universal Plug and Play (UPnP™) feature. UPNP provides compatibility with various networking equipment, software, and peripherals.

Select the box to allow the WAN port to be “pinged.” Blocking WAN pings may provide some extra security from hackers.

73D-Link DSL-2770L User Manual

Section 3 - Conguration

Port Mapping

This page allows you to congure port mapping settings for both the Ethernet ports and wireless APs.

LAN VLAN Settings:

Wireless LAN VLAN

Settings-AP:

WAN VLAN

Settings:

Enter the VID you want to use for each Ethernet port, as well as whether you want to apply Tx tagging for the port.

Enter the VID you want to use for each wireless AP, as well as whether you want to apply Tx tagging for the port.

Click this button to congure settings for each VID.

If you click on the WAN VLAN Settings button, these settings will appear:

VID:

Routing Type:

DHCP Setting:

WAN Type:

WAN Map VLAN ID:

Enter the VID you want to edit.

Select what routing type to use, NAT or Bridge.

If you select NAT, this will be DHCP by default.

If you select Bridge, select which WAN to use.

If you select Bridge, enter the VLAN ID to use.

74D-Link DSL-2770L User Manual

Section 3 - Conguration

SNMP Setup

This page allows you to congure the SNMP settings for remote management of this device.

SNMP Local:

SNMP Remote:

Get Community:

Set Community:

IP 1/2/3/4:

SNMP Version:

WAN Access IP

Address:

Set whether you want to enable local SNMP access for the router.

Set whether you want to enable remote SNMP access for the router.

Enter the community that the router will respond to for GetRequests.

Enter the community that the router will accept for SetRequests.

Enter the IP addresses of the PCs you will use for SNMP management.

Enter the SNMP version to use.

If you want to limit SNMP access to a specic PC/IP address only, enter the IP address here. By default, this is set to 0.0.0.0 and allows any computer to have SNMP access.

75D-Link DSL-2770L User Manual

Section 3 - Conguration

Remote Management

This page allows you to congure the remote management settings of this device.

Enable Remote

Management:

IP Allowed to

Access:

Port:

Tick this box to enable remote management. This will allow you to access the web conguration interface remotely through the Internet. This may require you to know your IP address or set up DDNS.

Enter the IP address you want to allow remote access from. By default, this is set to 0.0.0.0, which will allow access any computer on the Internet.

Set which port you want to use for remote access.

76D-Link DSL-2770L User Manual

Section 3 - Conguration

Routing

The Routing page allows you to specify custom routes that determine how data is moved around your network. After modifying any settings, click Save Settings to save your changes.

Select this box to enable routing, then select which routing protocol

RIP:

to use:

• RIPv1: Protocol in which the IP address is routed through the internet.

• RIPv2: Enhanced version of RIPv1 with added features such as Authentication, Routing Domain, Next Hop Forwarding, and Subnet-mask Exchange.

This identies the rule.

ID:

Destination:

Subnet Mask:

Gateway:

Hop:

Enable:

Enter in the IP of the specied network that you want to access using the static route.

Enter in the subnet mask to be used for the specied network.

Enter in the gateway IP address for the specied network.

Enter in the amount of hops it will take to reach the specied network.

Note: In a transmission path, each link is terminated at a network device such as a router or gateway. The number of hops equals the number of routers or gateways that data must pass through before reaching the destination.

Select this box to enable the rule.

77D-Link DSL-2770L User Manual

Section 3 - Conguration

IPv6 Firewall

This page lets you adjust the IPv6 rewall settings to control IPv6 trac allowed in and out of your network. After modifying any settings, click Save Settings to save your changes.

Congure IPv6

Filtering Below:

Name:

Schedule:

Source:

Dest:

Protocol:

Port Range:

Select whether to

• Turn IPv6 Filtering OFF

• Turn IPv6 Filtering ON and ALLOW computers listed to access the network (all computers not specied will be denied access)

• Turn IPv6 Filtering ON and DENY computers listed to access the network (all computers not specied will be allowed access)

For each rule, tick the checkbox on the left to enable the rule.

Enter a name for the rule.

Select whether to have the rule active Always, Never, or according to a schedule you have created. For more about creating schedules, refer to page 85.

Enter the starting IP address of the trac you want to lter.

Enter the ending IP address of the trac you want to lter.

Enter which protocol you want to lter.

Enter the port range of the trac you want to lter.

78D-Link DSL-2770L User Manual

Section 3 - Conguration

Budget Quota

This page lets you set quotas for how much trac is allowed to pass through the network. This may be useful to control usage if there is a bandwidth cap in place.

Enable Limitation

Quota:

Select Interface:

Limit Time(Days):

Enable Download

Quota:

Download Quota:

Enable Upload

Quota:

Upload Quota:

Trac Information:

Tick this box to enable quotas.

Select which interface to apply the budget quota to.

Enter the period of time to apply the budget quota to. After the time limit has passed, the quota will reset.

Tick this box to enable download quotas.

Set the maximum allowed download amount in megabytes for the period of time specied in Limit Time.

Tick this box to enable upload quotas.

Set the maximum allowed upload amount in megabytes for the period of time specied in Limit Time.

This shows your current received and transmitted trac totals so far. You can click the Refresh button to update the totals. Please note that the totals update every three minutes.

79D-Link DSL-2770L User Manual

Section 3 - Conguration

Tools

Password

This page will allow you to change the password used to log in to the web conguration interface.

Current/

New/Conrm

Password:

Session Idle

Time Out:

Enable

CAPTCHA:

To change the password, enter the current password, then the new password you want to use, then enter it again to conrm it, then click Apply Settings to save your changes.

Set the idle time in seconds that are allowed before the web conguration interface automatically logs out the user.

Enables a challenge-response test to require users to type letters or numbers from a distorted image displayed on the screen to prevent online hackers and unauthorized users from gaining access to your router’s network settings.

80D-Link DSL-2770L User Manual

Section 3 - Conguration

Save/Restore Settings

This section allows you to manage the router’s conguration settings, reboot the router, and restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created.

Save Settings to

Local Hard Drive:

Load Settings

from Local Hard

Drive:

Restore to

Factory Default

Settings:

Use this option to save the current router conguration settings to a le on the hard disk of the computer you are using. First, click the Save button. A le dialog will appear, allowing you to select a location and le name for the settings.

Use this option to load previously saved router configuration settings. First, use the Browse option to nd a previously saved le of conguration settings. Then, click the Load button to transfer those settings to the router.

This option will restore all conguration settings back to the settings that were in eect at the time the router was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current router conguration settings, use the Save button above.

81D-Link DSL-2770L User Manual

Section 3 - Conguration

Firmware Update

You can upgrade the rmware of the access point here. Make sure the rmware you want to use is on the local hard drive of the computer. Please check the D-Link support website for rmware updates at http://support.dlink.com. You can download rmware upgrades to your hard drive from this site.

Upload:

Accept Unocial

Firmware:

After you have downloaded the new rmware, click Browse... to locate the rmware update on your hard drive. Click Upload to complete the rmware upgrade.

Tick this box to allow unocial rmware to be loaded onto the device. Please note that this is not recommended, and any damage caused by an unocial rmware may invalidate your product warranty.

82D-Link DSL-2770L User Manual

Section 3 - Conguration

Ping Test

Ping Test:

Ping Results:

The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP address that you wish to Ping and click Ping.

The results of your ping attempts will be displayed here.

83D-Link DSL-2770L User Manual

Section 3 - Conguration

System Log

The router keeps a running log of events and activities occurring on the router. You may send these logs to a SysLog server on your network.

Log Types:

Enable E-mail

Notication:

To E-mail Address:

E-mail Subject:

SMTP Server/IP

Address:

SMTP Server Port:

Enable

Authentication:

Account Name:

Account/Verify

Password:

Tick the checkboxes to indicate whether you want to log events related to the System, Attacks, Dropped packets or connections, or Debug information.

Tick this box if you want to send event notications to your e-mail address.

Enter the e-mail address you want to send notications to.

Enter the e-mail subject to be used for the e-mail notications.

Enter the SMTP server to use, or the IP address of the SMTP server.

Enter the port of the SMTP server to use.

If your SMTP server requires authentication, tick this checkbox.

Enter your SMTP account name.

Enter your SMTP account password, then enter it again to verify it.

84D-Link DSL-2770L User Manual

Section 3 - Conguration

Schedules

Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm.

Schedule Rules

List:

Name:

Day(s):

Time Format:

Start Time:

End Time:

The list of schedules will be listed here. Click the Edit icon to make changes or click the Delete icon to remove the schedule.

Enter a name for your new schedule.

Select a day, a range of days, or All Week to include every day.

Choose a 24 hour or 12 hour clock-style.

Enter a start time for your schedule.

Enter an end time for your schedule.

85D-Link DSL-2770L User Manual

Section 3 - Conguration

Status

Device Info

This page displays the current information for the DSL-2770L. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address, then a Release button and a Renew button will be displayed. Use

Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use Disconnect to drop the PPPoE connection and use Connect

to establish the PPPoE connection.

General:

Select IPv4 Multi

WAN Type:

WAN:

Wireless LAN:

LAN:

Displays the router’s time and rmware version.

Use this dropdown box to select a connection to show information about.

Displays the MAC address and the public IP settings of the currently selected WAN type.

Displays the wireless MAC address and your wireless settings such as SSID and Channel.

Displays the MAC address and the private (local) IP settings for the router.

86D-Link DSL-2770L User Manual

Section 3 - Conguration

This page will display your current routing table.

Routing Info

87D-Link DSL-2770L User Manual

Section 3 - Conguration

IPv6 Status

The IPv6 page displays a summary of the Router’s IPv6 settings and lists the IPv6 address and host name of any IPv6 clients.

88D-Link DSL-2770L User Manual

Section 3 - Conguration

Support

The Support pages let you jump to descriptions of the settings and their functions.

89D-Link DSL-2770L User Manual

Section 3 - Conguration

D-Link SharePort

D-Link SharePort™ allows you to share a USB multifunction printer with other users across your network by simply connecting the device to select D-Link routers. This allows you to use a printer located across your network as if it were connected to your local PC.

System Requirements

- Windows 7 32-bit, 64-bit/ Vista/ XP/ 2003/ 2000

- Pentium 3 800 MHz or better

- 256 MB RAM or higher

- CD-ROM drive

- Compatible D-Link router

Installation

1. Insert the CD-ROM into your computer.

2. Follow the on-screen instructions.

3. The icon should appear in the System Tray at the lower-right corner on your desktop.

Set Up the D-Link Router

1. Connect the D-Link Router to the network.

2. Power on the D-Link Router.

3. Double-click on the icon to open D-Link SharePort.

4. Right-click on the icon in the System Tray at the lower-right corner on your Windows Desktop. A window will pop up to display the D-Link Router.

90D-Link DSL-2770L User Manual

Section 3 - Conguration

Enable Network USB on the D-Link Router

1. Click on the D-Link Router in D-Link SharePort.

2. Click Enable.

3. The icon in the Windows System Tray should change to a icon.

Connect a USB Printer to the D-Link Router

D-Link SharePort automatically detects each connected USB device. A window will pop up for each detected USB device.

1. Right-click the icon.

2. Click Open SharePort.

D-Link SharePort will display the connected USB printer on the network.

3. Move your mouse cursor cursor to Waiting to Connect and click Manage Device.

4. Click Yes for the question “Do you want to install the printer software or MFP utility?”

5. Insert the printer’s CD-ROM and follow the instructions to install the printer’s driver. When the installation process prompts you to connect the multifunction printer to your PC, click Next.

6. D-Link SharePort will virtually connect to the printer. Click Next.

7. Choose the printer’s driver that you want D-Link SharePort to auto-connect to when you print.

91D-Link DSL-2770L User Manual

Section 4 - Security

Connect a Wireless Client to your Router

WPS Button

The easiest and most secure way to connect your wireless devices to the router is WPS (Wi-Fi Protected Setup). Most wireless devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button (or a software utility with WPS) that you can press to connect to the DSL-2770L router. Please refer to your user manual for the wireless device you want to connect to make sure you understand how to enable WPS. Once you know, follow the steps below:

Step 1 - Press the WPS button on the DSL-2770L for about 1 second. The Internet LED on the front will start to blink.

WPS Button

Step 2 - Within 2 minutes, press the WPS button on your wireless client (or launch the software utility and start the WPS

process).

Step 3 - Allow up to 1 minute while your connection is congured. Once the Internet light stops blinking, you will be connected

and your wireless connection will be secure with WPA2.

92D-Link DSL-2770L User Manual

Section 4 - Security

Windows® 7

WPA/WPA2

It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.

1. Click on the wireless icon in your system tray (lower-right corner).

2. The utility will display any available wireless networks in your area.

Wireless Icon

93D-Link DSL-2770L User Manual

Section 4 - Security

3. Highlight the wireless connection with Wi-Fi name (SSID) you would like to connect to and click the Connect button.

If you get a good signal but cannot access the Internet, check your

TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.

4. The following window appears while your computer tries to connect to the router.

94D-Link DSL-2770L User Manual

Section 4 - Security

5. Enter the same security key or passphrase (Wi-Fi password) that is on your router and click Connect. You can also connect by pushing the WPS button on the router.

It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.

95D-Link DSL-2770L User Manual

Section 4 - Security

WPS

The WPS feature of the DSL-2770L can be congured using Windows® 7. Carry out the following steps to use Windows® 7 to congure the WPS feature:

1. Click the Start button and select Computer from the Start menu.

2. Click Network on the left side.

96D-Link DSL-2770L User Manual

D-Link DSL-2770L User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Preface

Manual Revisions

Trademarks

Product Overview

Package Contents

System Requirements

Introduction

Features

Hardware Overview

Back

Front/Bottom

Installation

Before you Begin

Wireless Installation Considerations

Setup Wizard (on Installation CD)

Connecting the DSL-2770L

SharePort Mobile App (iOS, Android)

Internet Setup

ADSL Interface

Setup Wizard

Ethernet/3G WAN Interface

Static IP

Dynamic IP (DHCP)

PPPoE (Username/Password)

PPTP

L2TP

Wireless Settings

Wireless Connection Setup Wizard

Wi-Fi Protected Setup

Manual Wireless Settings

LAN Setup

Router Settings

DHCP Server Settings (Optional)

Add DHCP Reservation

Time and Date

IPv6

USB Services

Disk Utility

File Sharing

Access Control

iTunes Server

Download Assistant

Download Status

Web HDD

SharePort Mobile

mydlink Settings

Advanced

Virtual Server

Application Rules

QoS Engine

Outbound Filters

Inbound Filters

Wireless Filter

DNS Setup

Firewall & DMZ

Advanced Internet

Advanced Wireless

Advanced LAN

Port Mapping

SNMP Setup

Remote Management

Routing

IPv6 Firewall

Budget Quota

Tools

Password

Save/Restore Settings

Firmware Update

Ping Test

System Log

Schedules

Status

Device Info

Routing Info

IPv6 Status

Support