Dlink DIV-140 User Manual

System Requirements

• Computers with Windows®, Macintosh®, or Linux-based operating systems
and an installed Ethernet Adapter

• Inter net Explorer version 6.0 or Netscape Navigator 7.0 or higher
(for configuration)

Package Contents

• D-Link DIV-140 VoIP Gateway

• Power Adapter

• CAT5 Ethernet Cable

• RJ-45 to DB-9 Cable

• Four (4) RJ-11 Cables

• CD-ROM with Installation Guide, User Manual, and Special Offers

Note: Using a power supply with a different voltage than the one included with
the DIV-140 may damage the unit and will void the warranty for this product.

If any of the above items are missing, please contact your reseller.

2D-Link DIV-140 Quick Install Guide

Connecting the DIV-140 to your network

Connect the power adapter to the receptor on the rear panel of the

A.

DIV-140 and then plug the other end of the power adapter to a wall
outlet or power strip. The power LED will turn ON to indicate proper
operation.

Connect the LAN interface to the hub or switch connected to your internal

B.

network using a CAT5 Ethernet cable. The LAN LED on the front of the
device should illuminate when a connection is made.

Connect the RJ-45 to DB-9 Console Cable from the Console port on the

C.

DIV-140 to the Com Port on the computer that will be used to configure
the DIV-140.

C. Console

U s e d t o c o n n ect t he
DIV-140 to the Com Port on
your computer.

Reset Button

Pre ss t o re set t he
DIV- 1 40 t o fa cto r y
default settings.

B. LAN Port

Connects DIV-140
to Ethernet enabled
device or switch.

PSTN Ports

Four (4) FXO ports used to
connect to wall phone jacks.

A. Power Receptor

Re ce pt or for Power
Adapter.

3 D-Link DIV-140 Quick Install Guide

Configuring the DIV-140

A computer on your LAN must be assigned an IP address and subnet mask
in the same range as the DIV-140. By default, the DIV-140 is assigned an IP
address of 10.0.0.1 with a subnet mask of 255.0.0.0. It can be configured in
two ways, through the web interface or command line interface (CLI).

With the console cable connected from the Console port of the DIV-140
to the Com port of your PC, launch the HyperTerminal program:

The terminal settings should
be 115200 8-N-1-N.

Power on the DIV-140, after the device boots up, login when prompted:

Enter admin for the Username and password for the
Password.

4D-Link DIV-140 Quick Install Guide

It may be necessary to change the IP address of the DIV-140 to match
your local network. To change the IP address of the DIV-140, use the
following commands and procedure below:

At the Gat eway pr om pt , en te r th e co mmand, “s et nw ip
[IP address] [subnet mask] [gateway address] [DNS address]”
and press Enter.

Verify the IP settings by entering the command, “show nw ip” and
pressing Enter. The IP settings will display:

5 D-Link DIV-140 Quick Install Guide

Save the IP settings by using the “save” command. Press Enter,
and the DIV-140 will save the settings and reboot:

After setting the IP address, you can configure the DIV-140 from the web
configuration using a computer on your LAN. Open a web browser and
browse to the IP address of the DIV-140 using https.

Ex. https://192.168.0.2

A Security Alert window will appear:

Click Yes

6D-Link DIV-140 Quick Install Guide

A login box will appear. Enter the user name and password. The default
user name is admin, and the default password is password.

Click OK

After logging in, the System Information page will appear:

7 D-Link DIV-140 Quick Install Guide

The following figure displays the setup for making VoIP to PSTN calls using
the DIV-140:

8D-Link DIV-140 Quick Install Guide

The configuration settings on the DIV-140 are as follows:

After logging into the DIV-140, browse to the System Configuration >
Device page:

Verify the Country is set to the correct region and click Apply:

Browse to the Network Configuration > General page:

Verify the IP Configuration settings are correct, and click Apply:

9 D-Link DIV-140 Quick Install Guide

Browse to the Network Configuration > General page:

Enter the VoIP Server IP PBX IP address or domain name and
Server Port. The server port is 5060 by default. Click Apply:

Browse to the Port Configuration > General page:

The DIV-140 has four (4) PSTN ports numbered 1-4. Select port
1 and configure the Phone Number and Display Name as 2001
Click Apply:

10D-Link DIV-140 Quick Install Guide

Configure PSTN ports 2-4 similarly, assigning them Phone Number and
Display Names of 2002, 2003 and 2004 resepctively:

Browse to the Save Changes page anc click Save Changes:

The DIV-140 will reboot.

The VoIP server (IPPBX) needs to be configured as follows:

The PSTN Ports (2001-2004) must be added as gateways on the IPPBX.
The gateways should be added to the route used by the users of the
IPPBX.

When the DIV-140 reboots, it will register with the IPPBX.

Connect PSTN to port 1 of the DIV-140.

To make a VoIP call from 111 to a PSTN phone 437:

• Pick up the VoIP phone (111) handset and dial 2001#. This will cause
the VoIP Gateway FXO port 2001 to ring twice before going offhook.

• After 2001 goes offhook, you will be connected to the local PBX and
will get the PBX dialtone. Dial the PBX extention number 437.

• The PBX phone 437 will ring. When the user at 437 picks up the phone,
the call is established.

11 D-Link DIV-140 Quick Install Guide

Technical Support

D-Link’s website contains the latest user documentation and

software updates for D-Link products.

U.S. and Canadian customers can contact D-Link Technical

Support through our website or by phone.

United States

Telephone

[phone]

World Wide Web

http://support.dlink.com

Canada

Telephone

[phone]

World Wide Web

http://support.dlink.ca

Version 1.0

September 13, 2006

Copyright ©2006 D-Link Corporation/D-Link Systems, Inc. All rights reserved. D-Link and the D-Link logo are registered
trademarks of D-Link Corporation or its subsidiaries in the United States and other countries. Other trademarks are the property
of their respective owners. Product specifications, size and shape are subject to change without notice, and actual product
appearance may differ from that depicted herein.

12D-Link DIV-140 Quick Install Guide