D-Link DI-624S User Manual

D-Link

DI-624S

High-Speed 2.4 GHz

Wireless Storage Router

Manual

Building Networks for People

Ver 1.00

Contents

Package Contents........................................................................................................... 3

Introduction ..................................................................................................................... 4

Connections ....................................................................................................................5

LEDs ................................................................................................................................. 6

Features ........................................................................................................................... 7

Wireless Basics............................................................................................................... 9

Standards-Based Technology ................................................................................... 10

Installation Considerations......................................................................................... 10

Getting Started .............................................................................................................. 11

Installing the Print Server........................................................................................... 12

Using the Configuration Wizard .................................................................................. 13

Home > Wireless ....................................................................................................... 14

Home > WAN............................................................................................................. 18

Home > LAN .............................................................................................................. 25

Home > DHCP ........................................................................................................... 26

Home > File Sharing.................................................................................................. 27

Home > FTP .............................................................................................................. 31

Home > Personal Web............................................................................................... 32

Home > UPnP AV...................................................................................................... 34

Advanced > Virtual Server......................................................................................... 35

Advanced > Applications ........................................................................................... 37

Advanced > Filters..................................................................................................... 38

Advanced > Parental Control..................................................................................... 41

Advanced > Firewall .................................................................................................. 44

Advanced > DMZ....................................................................................................... 45

Advanced > DDNS..................................................................................................... 46

Advanced > Printer .................................................................................................... 47

Advanced > QoS........................................................................................................ 48

Advanced > Performance .......................................................................................... 52

Tools > Admin............................................................................................................ 54

Tools > Time.............................................................................................................. 55

Tools > System.......................................................................................................... 56

Tools > Firmware....................................................................................................... 57

Tools > Misc............................................................................................................... 58

Tools > Cable Test..................................................................................................... 60

Status > Device Info................................................................................................... 61

Status > Log............................................................................................................... 63

Status > Statistics ...................................................................................................... 64

Status > Wireless....................................................................................................... 65

Status > Printer Info ................................................................................................... 66

Active Session ........................................................................................................... 67

Help............................................................................................................................69

Technical Specifications .............................................................................................. 70

Appendix........................................................................................................... 73

Package Contents

Contents of Package:

• D-Link DI-624S 2.4GHz Wireless Storage Router

• Power Adapter-DC 5V, 3A

• Manual and Warranty on CD

• Quick Installation Guide

• Ethernet Cable (All the DI-624S’s Ethernet ports are

Auto-MDIX)

Note: Using a power supply with a different voltage rating than the one included with the DI-624S will cause damage and void the warranty for this product.

If any of the above items are missing, please contact your reseller.

• System Requirements for Configuration

• Ethernet-Based Cable or DSL Modem

• Computers with Windows, Macintosh, or Linux-based

operating systems with an installed Ethernet adapter

• Computers with Windows, Macintosh, or Linux-based

operating systems with an installed Ethernet adapter

• Internet Explorer Version 6.0 or Netscape Navigator

Version 7.0 and Above

Introduction

The D-Link DI-624S Wireless Storage Router is an 802.11b/g high-performance, wireless router that supports high-speed wireless networking at home, at work or in public places.

Unlike most routers, the DI-624S provides data transfers at up to 8X (compared to the standard 11 Mbps) when used with other D-Link products. The 802.11g standard is backwards compatible with 802.11b products. This means that you do not need to change your entire network to maintain connectivity. You may sacrifice some of 802.11g’s speed when you mix 802.11b and 802.11g devices, but you will not lose the ability to communicate when you incorporate the 802.11g standard into your 802.11b network. You may choose to slowly change your network by gradually replacing the 802.11b devices with 802.11g devices.

In addition to offering faster data transfer speeds when used with other 802.11g products, the DI-624S has the newest, strongest, most advanced security features available today. When used with other 802.11g WPA or WPA2 (WiFi Protected Access) and 802.1x compatible products in a network with a RADIUS server, the security features include:

WPA Wi-Fi Protected Access authorizes and identifies users based on a secret key that changes automatically at a regular interval. WPA uses TKIP (Temporal Key Integrity Protocol) to change the temporal key every 10,000 packets (a packet is a kind of message transmitted over a network.) This insures much greater security than the standard WEP security. (By contrast, the older WEP encryption required the keys to be changed manually.)

WPA2, based on the IEEE 802.1i Wi-Fi certified standard, goes a level beyond the previous WPA by enhancing security with a new encryption code. Employing AES (Advanced Encryption Standard), and yet still backwards compatible with WPA, WPA2 utilizes 802.1X and EAP (Extensible Authentication Protocol) to verify users on the wireless network using a Pre-Shared Key. Once all users on the LAN have been authenticated, there can be a securely encrypted flow of information between all parties on the LAN.

For home users that will not incorporate a RADIUS server in their network, the security for the DI-624S, used in conjunction with other 802.11g products, will still be much stronger than ever before. Utilizing the Pre Shared Key mode of WPA, the DI-624S will obtain a new security key every time it connects to the 802.11g network. You only need to input your encryption information once in the configuration menu. No longer will you have to manually input a new WEP key frequently to ensure security, with the DI-624S, you will automatically receive a new key every time you connect, vastly increasing the safety of your communications.

The DI-624S comes equipped with two 2.0 USB ports on the rear panel. These ports increase the functionality of the router exponentially. Utilizing any of these USB ports, the administrator can now enable the router to be a print server as well. These ports are especially ideal for outside users wanting to view files on your D-Link Media Lounge using the UPnP AV function on the router. You may also share files with users on you LAN or WAN by attaching a network storage device to one of these USB ports and using one of the sharing functions on the router, either the file server or the FTP Server function.

Connections

All Ethernet Ports (WAN and LAN) are auto MDI/MDIX, meaning you can use either a straight-through or a crossover Ethernet cable.

USB 2.0 Connections.

Use these ports to connect your USB

printer or memory

media for file sharing.

Factory Reset Button

Pressing this button

will restore the router

to its factory default

settings.

Auto MDI/MDIX LAN Ports

Connect the Ethernet

cable from computers on

your LAN to these ports.

Connect the Ethernet

cable from your ADSL

modem to this port.

WAN Port

Power Adapter

Connect your

5V 3A power

adapter here.

LEDs

WAN LED

An active LED

Power LED

A solid light

indicates a valid

connection to

the power

supply.

Status LED

indicates a link

has been

established. A

blinking LED

indicates

activity on the

WAN port.

USB LED

An active LED indicates

a link has been

established. A blinking

LED indicates activity

on the USB port.

A blinking LED

indicates the

DI-624S is

functioning

properly.

WLAN LED

An active LED indicates

a link has been

established. A blinking

LED indicates activity

on the WLAN port.

LAN LEDs

An active LED indicates

a link has been

established. A blinking

LED indicates activity on

the LAN port.

Features

• Fully compatible with the 802.11g standard to provide a wireless data rate of up

to 54Mbps

• Backwards compatible with the 802.11b standard to provide a wireless data rate

of up to 11 Mbps

• WPA authorizes and identifies users based on a secret key that changes

automatically at a regular interval, for example:

• TKIP (Temporal Key Integrity Protocol), in conjunction with a RADIUS server,

changes the temporal key every 10,000 packets, ensuring greater security

• Pre Shared Key mode means that the home user, without a RADIUS server, will

obtain a new security key every time the he or she connects to the network, vastly improving the safety of communications on the network

• New WPA2 enhanced wireless security authenticates using 802.1X and a

Pre-Shared key, and encrypts the data with the AES encryption standard. Wi-Fi certified, WPA2 is also compatible with WPA and can be used for a large network or for the SOHO environment

• 802.1x Authentication in conjunction with the RADIUS server verifies the identity

of would be clients

• Utilizes OFDM technology (Orthogonal Frequency Division Multiplexing)

• User-friendly configuration and diagnostic utilities

• Operates in the 2.4GHz frequency range

• Connects multiple computers to a Broadband (Cable or DSL) modem to share

the Internet connection

• Advanced Firewall features

• Supports NAT with VPN pass-through, providing added security

• MAC Filtering

• IP Filtering

• URL Filtering

• Domain Blocking

• Scheduling

• DHCP server supported enables all networked computers to automatically

receive IP addresses

• Web-based interface for Managing and Configuring

• Access Control to manage users on the network

• Supports special applications that require multiple connections

• Equipped with 4 10/100Mbps Ethernet ports, 1 WAN port, Auto MDI/MDIX

• Equipped with two 2.0USB ports at the rear of the router used to connect

various devices to be shared over a network, such as USB storage devices and printers

• VPN Pass Through

• DMZ and DDNS functions

• Stateful Packet Inspection for protection against unwanted packets

• Quality of Service (QoS) for prioritizing ports and IP addresses

• UPnP AV function for sharing audio and video files using a media storage

device

• Multiple users and administrators with configurable privileges for each

• Intrusion detection for ICMP, SYN, UDP flood, Land, IP spoof, Ping of Death,

Port Scan, Smurf, Steal Fin, Syn with data, Tear Drop, and UDP bomb attacks

• Statistics for all main functions on the router

Wireless Basics

D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. D-Link wireless products will allow you access to the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking brings.

A WLAN is a cellular computer network that transmits and receives data with radio signals instead of wires. WLANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently. Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users.

Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards.

People use wireless LAN technology for many different purposes:

Mobility - Productivity increases when people have access to data in any location

within the operating range of the WLAN. Management decisions based on real-time information can significantly improve worker efficiency.

Low Implementation Costs – WLANs are easy to set up, manage, change and

relocate. Networks that frequently change can benefit from WLANs ease of implementation. WLANs can operate in locations where installation of wiring may be impractical.

Installation and Network Expansion - Installing a WLAN system can be fast and

easy and can eliminate the need to pull cable through walls and ceilings. Wireless technology allows the network to go where wires cannot go - even outside the home or office.

Scalability – WLANs can be configured in a variety of topologies to meet the needs

of specific applications and installations. Configurations are easily changed and range from peer-to-peer networks suitable for a small number of users to larger infrastructure networks to accommodate hundreds or thousands of users, depending on the number of wireless devices deployed.

Inexpensive Solution - Wireless network devices are as competitively priced as

conventional Ethernet network devices.

Wireless Basics (continued)

Standards-Based Technology

The DI-624S Wireless Broadband Router utilizes the new 802.11g standard.

The IEEE 802.11g standard is an extension of the 802.11b standard. It increases the data rate up to 54 Mbps within the 2.4GHz band, utilizing OFDM technology.

This means that in most environments, within the specified range of this device, you will be able to transfer large files quickly or even watch a movie in MPEG format over your network without noticeable delays. This technology works by transmitting high speed digital data over a radio wave utilizing OFDM (Orthogonal Frequency Division Multiplexing) technology. OFDM works by splitting the radio signal into multiple smaller sub-signals that are then transmitted simultaneously at different frequencies to the receiver. OFDM reduces the amount of crosstalk (interference) in signal transmissions.

The DI-624S is backwards compatible with 802.11 b devices. This means that if you have an existing 802.11 b network, the devices in that network will be compatible with

802.11g devices at speeds of up to 11 Mbps in the 2.4GHz range.

Installation Considerations

The D-Link DI-624S lets you access your network, using a wireless connection, from virtually anywhere within its operating range. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:

1. Keep the number of walls and ceilings between the DI-624S and other network

devices to a minimum - each wall or ceiling can reduce your D-Link wireless product’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.

2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick

(.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.

3. Building Materials can impede the wireless signal - a solid metal door or

aluminum studs may have a negative effect on range. Try to position wireless devices and computers with wireless adapters so that the signal passes through drywall or open doorways and not other materials.

4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical

devices or appliances that generate extreme RF noise.

Getting Started

Setting up a Wireless Infrastructure Network

Please remember that D-Link AirPlus G wireless devices are pre-configured to connect together, right out of the box, with their default settings. For a typical wireless setup at home (as shown above), please do the following:

1. You will need broadband Internet access (a Cable or DSL-subscriber line

into your home or office)

2. Consult with your Cable or DSL provider for proper installation of the

modem

3. Connect the Cable or DSL modem to the DI-624S Wireless Storage Router

(see the printed Quick Installation Guide included with your router.)

4. If you are connecting a desktop computer to your network, install the D-Link

AirPlus G DWL-G520 wireless PCI adapter into an available PCI slot on your desktop computer. You may also install the DWL-G520.

5. (See the printed Quick Installation Guide included with the network

adapter.)

6. Install the D-Link DWL-G650 wireless Cardbus adapter into a laptop

computer. (See the printed Quick Installation Guide included with the DWL-G650.)

7. Install the D-Link DFE-530TX+ adapter into a desktop computer. The four

Ethernet LAN ports of the DI-624S are Auto MDI/MDIX and will work with both Straight-Through and Cross-Over cable.

(See the printed Quick Installation Guide included with the DFE-530TX+.)

Connect your printer to the printer port on the DI-624S. Please refer to the quick installation guide for loading the print server software.

Installing the Print Server

To avoid any problems that may arise when you install your USB printer, follow this procedure. If the print server is powered on before a network connection is established, configuration problems may arise.

1. Before connecting your printer to the DI-624S, make sure that your printer is

functioning properly.

2. Once you have made sure that it is working properly, turn off the power to the

printer.

3. Confirm that your computer network is functioning properly.

4. Connect the DI-624S to your network, using a standard Ethernet cable. Leave

the router powered off.

5. While the printer is still powered off, connect the printer to one of the available

USB slots at the rear of the router.

6. Power on your USB printer.

7. Plug the power adapter into the available power adapter slot at the back of the

router.

8. Plug the other end of the power adapter into an available power outlet. This will

supply electricity to the Router since there is no external power switch. The corresponding green USB LED at the front of the router should light green, indicating a valid connection to the router.

To configure the router for use on your LAN, please go to the Advanced section of this manual, under the heading Home > LAN.

Using the Configuration Wizard

Whenever you want to configure your network or the DI-624S, you can access the Configuration Menu by opening the web-browser and typing in the IP Address of the DI-624S. The DI-624S default IP Address is shown to the right:

• Open the web browser

• Type in the IP Address of the

Router (http://192.168.0.1

)

• Type admin in the User Name

• Leave the Password blank

field

• Click OK

192.168.0.1

The Home > Wizard screen will appear. Please refer to the Quick Installation Guide for more information regarding the Setup Wizard.

These buttons appear on most of the configuration screens in this section. Please click on the appropriate button at the bottom of each screen after you have made a configuration change.

Note: if you have changed the default IP Address assigned to the DI-624S, make sure to enter the correct IP Address.

Clicking this button will save configured settings to the router.

Clicking Cancel will clear changes made to the current page.

Clicking Help will provide the user with helpful information about the current window.

Click refresh will refresh the statistics of the

Using the Configuration Menu (continued)

Home > Wireless

WCN

WCN or Windows Connect Now Technology is used to automatically

configure the wireless settings for this device. The WCN must be previously configured on computer running a Windows XP operating system, which has Service Pack 2 installed. Once the configuration has been completed by running the Wireless Network Setup Wizard, it must be saved to a USB enabled memory device and then uploaded automatically to the router and any other device to be put on this wireless network, using this method. No configuration will be necessary except for ensuring that this WCN radio button is enabled before connecting the memory drive to the router. For a concise explanation on configuring the WCN on Windows XP, see the

Appendix at the back of this manual.

(Note: For the client implementation of this function, please see the user manual for the associated client PC)

Wireless Radio Click the appropriate radio button to enable or disable the Wireless

Access part of this device.

Wireless QoS (WMM)

Clicking the Enabled radio button in this section will enable QoS for WiFi MultiMedia (WMM). This function will give priority to audio and video information travelling over the wirless network. This function is especially important in sharing files over your LAN using a media server, such as the D-Link Media Lounge and thus will help provide a continuous media stream.

SSID

Channel

Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID’s factory default setting is DI-624S. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. This field will be automatically configured for users who have uploaded a WCN configuration.

What channels are available for use by the access point depends on the local regulatory environment. Remember that all devices communicating with the device must use the same channel (and use the same SSID). Use the drop down menu to select the channel used for your 802.11b wireless LAN.

Super G Mode Enabling this function will aid in the throughput performance of the

router by adding Dynamic Packet Bursting, Fast Frames, Hardware Encryption and Compression and Turbo Mode. The default setting is Disabled. The user has three choices:

None – Super G Mode is disabled.

Super G without Turbo – Will enable Dynamic Packet Bursting, Fast

Frames and Hardware Encryption and Compression, while leaving the Turbo Mode disabled.

Super G with Dynamic Turbo – Enabling this function will enable

Dynamic Packet Bursting, Fast Frames and Hardware Encryption and Compression, and Dynamic Turbo mode. This mode allows the router to use two radio channels to double the data transfer rate. All nodes on the wireless network must be Turbo capable for this function to work. If not, all devices on this wireless network will have a normal data transfer rate. Turbo mode is only enabled for use when all devices on the wireless LAN are turbo enabled. This turbo mode is backwards compatible with non-Turbo legacy devices.

Authentication This router employs three basic types of Authentication for access to

the router’s wireless network, Open System/Shared Key 802.1X (RADIUS) and PSK (Pre-Shared Key), which can be selected by clicking the corresponding radio button. Each selection will alter the window to accommodate the entry of the selected Authentication. See the explanation below for more information.

Open System/Shared Key

The Open System/Shared Key choice for Authentication will produce the same screen for the user’s configuration. The Open System choice is for general use and utilizes the basic WEP encryption. The Shared Key choice is used between cooperating devices that share a common encryption key. WEP (Wireless Encryption Protocol or Wired Equivalent Privacy) encryption can be enabled for security and privacy. WEP encrypts the data portion of each frame transmitted from the wireless adapter using one of the predefined keys. Decryption of the data contained in each packet can only be done if the both the receiver and transmitter have the correct shared key.

WEP – Click the Enabled radio button to employ WEP encryption on the router.

WEP Encryption - Use the drop down menu to select the type of WEP encryption. Select 64 Bit

to enabled 64 bit Hexadecimal encryption, 128 Bit to enable 128 bit Hexadecimal encryption. For 64-bit encryption, the (ASCII) characters are converted automatically and listed as 10-digit hexadecimal keys. 64-bit encryption allows you to select one of four active keys. For 128-bit encryption, the characters are converted and listed as a 26 digit hexadecimal key. 128-bit encryption allows you to select one of four active keys. 128-bit keys are to be from 5-13 inputted characters in length and 256-bit keys must be from 10-26 inputted characters in length. Failing to have the same key on the server and its clients will result in the clients not receiving any information from the router or its connected devices.

Key Type – Use the pull-down menu to select the type of Key to be used for encryption. The user

may choose HEX (Hexidecimal) or ASCII (American Standard Code for Information Interchange). Both will require the user to enter a key in the following field.

Key – The user may enter up to four keys to be used for encryption. Only the key selected using

the corresponding radio button will be used for encryption.

Click Apply to set the information in the router’s memory.

of this function, please see the user manual for the associated client PC)

(Note: For the client implementation

WPA

WPA or Wireless Protection Access is a new an improved standard of wireless security. WPA offers encryption keys of up to 256-bits that automatically change frequently. On this router, the WPA utilizes the RADIUS protocol, which utilizes a server to authorize the user by matching a Shared Secret password listed in its RADIUS database. There are two choices for the user to choose from. WPA and WPA2 which uses the Advanced Encryption Standard (AES). In order to use this function, a RADIUS server must be established on a computer on the LAN. This RADIUS server must be configured to have the same key as the users on the LAN accessing it.

RADIUS Server IP – Enter the IP address of the remote RADIUS server through which you will

be authenticated.

Port – Enter the virtual port number to which to connect through the RADIUS server. Common

port numbers for RADIUS are 1812 and 1813.

Shared Secret – Enter the password which will be used to authenticate you on the wireless

network. This password must be the same on the RADIUS server in order for you to be authorized.

(Note: For the client implementation of this function, please see the user manual for the associated client PC)

WPA-PSK

WPA-PSK (Pre-Shared Key) uses the same encryption as the WPA but is implemented differently. All devices on the wireless network share the same key (Passphrase) to activate the WPA security. There are two choices for the user to choose from. WPA-PSK and WPA2-PSK which uses the Advanced Encryption Standard (AES). To utilize, select one of the previous choices,

enter the Passphrase, confirm it in the second field and click Apply.

(Note: For the client implementation of this function, please see the user manual for the associated client PC)

Using the Configuration Menu (continued)

Home > WAN

Static IP Address

IP Address

Input the public IP Address provided by your ISP.

Subnet Mask

ISP Gateway Address-

Primary DNS Address

Secondary

DNS

Address

Choose Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.

Input your Subnet mask. (All devices in the network must have the same subnet mask.)

Input the public IP address of the ISP to which you are connecting.

Input the primary DNS (Domain Name Server) IP address provided by your ISP

This is an optional DNS Address entry to be used if the primary DNS fails.

MTU

Enter an MTU value only if required by your ISP. Otherwise, leave it at

the default setting.

Using the Configuration Menu (continued)

Dynamic IP Address

Dynamic

Host Name

MAC Address

Choose Dynamic IP Address to obtain IP address information

automatically from your ISP. This option should be selected if your ISP has not supplied you with an IP address. for Cable modem services.

This option is commonly used

The Host Name is optional but may be required by some ISPs. The

default host name is the device name of the Router and may be changed.

The default MAC Address is set to the WAN’s physical interface MAC

address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP.

Clone MAC Address The default MAC address is set to the WAN’s physical interface MAC

address on the Broadband Router. You can use the “Clone MAC Address” button to copy the MAC address of the Ethernet Card installed by your ISP and replace the WAN MAC address with the MAC address of the router. It is not recommended that you change the default MAC address unless required by your ISP.

Primary/Secondary DNS Address

Enter a DNS Address if you wish not to use the address provided by

your ISP.

MTU Enter an MTU value only if required by your ISP. Otherwise, leave it at

the default setting.

Using the Configuration Menu (continued)

Home > WAN > PPPoE

Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection. Select Static PPPoE to use a static IP address for

our PPPoE connection.

PPPoE

Choose this option if your ISP uses PPPoE. (Most DSL users will select this option.)

Dynamic PPPoE Choose this option to receive an IP Address automatically from your ISP.

Static PPPoE Choose this option to you have an assigned (static) IP Address.

Password Enter The PPPoE user name provided to you by your ISP.

Retype Password Retype the password entered in the previous field.

Service Name Enter the Service Name provided by your ISP (optional).

IP Address This option is only available for Static PPPoE. Enter the static IP

address for the PPPoE connection.

MAC Address The default MAC Address is set to the WAN’s physical interface MAC

address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP.

Clone MAC Address

The default MAC address is set to the WAN’s physical interface MAC address on the Broadband Router. You can use the “Clone MAC Address” button to copy the MAC address of the Ethernet Card installed by your ISP and replace the WAN MAC address with the MAC address of the router. It is not recommended that you change the default MAC address unless required by your ISP.

Primary DNS Address

Input the primary DNS (Domain Name Server) IP address provided by your ISP

Secondary DNS Address

This is an optional DNS Address entry to be used if the primary DNS fails.

Maximum Idle Time The amount of time of inactivity before the device will disconnect time

your PPPoE session. Enter a Maximum Idle Time (in minutes) to define a maximum period of time for which the Internet connection is maintained during inactivity. If the connection is inactive for longer than the defined Maximum Idle Time, then the connect ion will be dropped. Either set the value for idle time to zero or enable Auto-reconnect to disable this feature.

MTU Enter an MTU value only if required by your ISP. Otherwise, leave it at

the default setting.

Connect Mode Allows the user to choose a method of connecting to the ISP.

Always-On will keep the router connected through Idle times. Manual will require the user to connect manually using the router anytime a connection to the ISP has timed out. Connect-on-demand will instruct the router to connect to the ISP anytime information is sent from the connected computer on the LAN.

Click Apply to set any changes made to the memory of the router.

Using the Configuration Menu (continued)

Home > WAN > Others > PPTP

PPTP or Point-to-Point Protocol is a safe method of sending information between VPN’s securely using encryption over PPP. You, as the client, need to enter the correct information that the server has in order to create that secure tunnel. Using Dynamic IP, the router will set your basic IP parameters for you, such as the IP Address, Subnet Mask and Gateway. For Static IP, this information must be set manually by the user. All information in this window should be provided by your ISP.

PPTP

Choose between Dynamic and Static IP.

IP Address Enter the IP address of the router for a static IP entry. Dynamic IP

requires no input here.

Subnet Mask Enter the Subnet Mask address of the router for a static IP entry.

Dynamic IP requires no input here.

Gateway Enter the gateway address here. This is the IP address of the ISP

server.

Server IP Enter the IP address of the PPTP’s server computer. This is how the

user will become authenticated to use PPTP.

PPTP Account Enter the name of the PPTP account as provided to you by your ISP.

PPTP Password Enter the PPTP password as provided to you by your ISP.

PPTP Retype Retype the password entered in the PPTP Password field. Password

Maximum Idle Time

A value of 0 means that the PPP connection will remain connected. If your network account is billed according to the amount of time the Router is actually connected to the Internet, enter an appropriate Idle Time value (in seconds). This will disconnect the Router after the WAN connection has been idle for the amount of time specified. The default value = 5.

MTU Enter an MTU value only if required by your ISP. Otherwise, leave it at

the default setting.

Connect Mode This function, with Connect-on-demand selected, will allow the router

to connect any workstation on your LAN to the Internet upon request. If this function is set at Always-on, no request from the workstation will be needed to connect to the Internet. If Manual is selected, it will be necessary for the workstation on the LAN to manually connect to the Internet through this router.

Using the Configuration Menu (continued)

Home > WAN > Others > L2TP

Some ISPs may require the user to uplink using the Layer 2 Protocol Tunneling (L2PT) method. L2PT is a VPN protocol that will ensure a direct connection to the server using an authentication process that guarantees the data originated from the claimed sender and was not damaged or altered in transit. Once connected to the VPN tunnel, it seems to the user that the client computer is directly connected to the internal network. To set up your L2PT connection, enter

the following data your ISP.

that was provided to you by

L2PT

IP Address

Choose between Dynamic and Static IP. Using Dynamic IP, the router will set your basic IP parameters, such as the IP Address, Subnet Mask and Gateway. For Static IP, this information must be set manually by the user.

The IP address that will be assigned to your router for this connection, as stated by your ISP. Dynamic IP requires no input here.

Subnet Mask The IP address of the corresponding Subnet Mask, as stated to you by

your ISP. Dynamic IP requires no input here.

Gateway The IP address of the gateway device, as stated to you by your ISP.

Dynamic IP requires no input here.

Server IP The IP address of your ISP’s server computer, as stated to you by your

ISP.

L2PT Account The account name of the L2PT account that has been assigned to you

by your ISP.

L2PT Password The password of the L2PT account that was supplied to you by your

ISP.

L2PT Retype Password Retype the password that was entered in the L2PT field. Ensure that

these two passwords are identical or an error will occur.

Maximum Idle Time A value of 0 means the PPP connection will remain connected. If your

network account is billed according to the amount of time the Router is actually connected to the Internet, enter an appropriate Idle Time value (in seconds). This will disconnect the Router after the WAN connection has been idle for the amount of time specified. The default value = 5.

MTU Enter an MTU value only if required by your ISP. Otherwise, leave it at

Connect Mode

the default setting.

If Connect-on-demand is selected, will allow the router to connect any workstation on your LAN to the Internet upon request. If Always-on, no request from the workstation will be needed to connect to the Internet. If Manual is selected, the workstation on the LAN must manually connect to the Internet through this router.

Using the Configuration Menu (continued)

Home > WAN > Others > BigPond Cable

This selection is for users having Big Pond Cable as their ISP. Enter the following information, as provided to you by your ISP.

User Name

Password

Enter The PPPoE user name provided to you by your ISP.

Enter the user name as provided to you by your ISP.

Retype Password Retype the password entered in the previous field.

Auth Server Enter the name of the Authentication Server as provided to you by

your ISP. This is the computer that will accept your user name and password to be authenticated on the network.

Auto Reconnect Checking the Enabled radio button will allow the router to reconnect to

the network automatically if it becomes disconnected.

+ 57 hidden pages