dji MATRICE 210 RTK V2, MATRICE 200 V2, MATRICE 200 V2 Series, MATRICE 210 V2 User Manual

MATRICE 200 SERIES V2

Manifold 2 Mounting Bracket

User Guide

使用说明

ユーザーガイド

Bedienungsanleitung

Guía del usuario

Guide de l'utilisateur

Guida dell'utente

Gebruiksaanwijzing

Manual do utilizador

2019.05v1.0

I.

A

II.

A

III.

C

B

IV.

EN

Disclaimer

Congratulations on purchasing your new DJITM product. The information in this document
affects your safety and your legal rights and responsibilities. Read this entire document

carefully to ensure proper conguration before use. Failure to read and follow instructions and

warnings in this document may result in serious injury to yourself or others, damage to your
DJI product, or damage to other objects in the vicinity. This document and all other collateral
documents are subject to change at the sole discretion of DJI.

By using this product, you hereby signify that you have read this disclaimer and warning
carefully and that you understand and agree to abide by the terms and conditions herein. You
agree that you are solely responsible for your own conduct while using this product, and for
any consequences thereof. You agree to use this product only for purposes that are proper
and in accordance with all applicable laws, rules, and regulations, and all terms, precautions,
practices, policies and guidelines DJI has made and may make available.

Introduction

Mount the MANIFOLDTM 2 to the MATRICETM 210 V2, Matrice 210 RTK V2, Matrice 210,

or Matrice 210 RTK aircraft using the mounting bracket and then connect the cables. The
descriptions below use the M210 V2 and M210 RTK V2 as an example.

In the Box

Mounting Bracket Set × 1 L-shaped Wrench × 1

Type A Screw (M2.5×8, Hex) × 10 USB Cable (with 2 Type A Ports) × 1

Type B Screw (M1.6×4, Philips) × 4 XT30 Power Cable × 1

Type C Screw (M2.5×14, Hex) × 4

Usage

1. As shown in gure I, assemble the body of the mounting bracket, then tighten the six type A

screws.

2. As shown in gure II, mount the L-shaped blocks to the Manifold 2, then tighten the four type

A screws.

3. As shown in gure III, mount the Manifold 2 and mounting bracket to the upper cover of the

aircraft, then tighten the four type B screws and four type C screws. Make sure to install

them in the direction shown in the gure. DO NOT reverse any item.

4. As shown in gure IV, connect the USB 3.0 port (Type A) on the Manifold 2 to the USB port

at the rear of the aircraft using the USB cable (with 2 Type A ports), connect the power port
on the Manifold 2 to the extended power port at the rear of the aircraft using the XT30 power
cable, and then put the cables into the cable clip on the mounting bracket.

5. Connect the expansion port 3 at the rear of the aircraft to the USB 3.0 port (Type A) or UART
port on the Manifold 2 using an appropriate cable. Refer to the Manifold 2 User Guide for

details. (https://www.dji.com/manifold-2 )

6. When using the Manifold 2, slide the USB mode switch at the rear of the aircraft to the right

.

Make sure that the cables do NOT obstruct the Upward Infrared Sensor on the top of

the aircraft.

When using with the M210 V2 aircraft, a GPS Kit is required. Refer to the GPS Kit

document for details.

When using with the M210 RTK V2 aircraft, arrange the D-RTK antenna cables

properly to prevent them from being bent excessively when the mounting bracket is
mounted.

Please refer to http://www.dji.com/service for after-sales service for your product where applicable.
DJI shall mean SZ DJI TECHNOLOGY CO., LTD. and/or its afliated companies where applicable.

CHS

免责声明

感谢您购买 DJITM产品。本文所提及的内容关系到您的安全以及合法权益与责任。使用本产品
之前，请仔细阅读本文以确保已对产品进行正确的设置。不遵循和不按照本文的说明与警告来
操作可能会给您和周围的人带来伤害，损坏本产品或其它周围的物品。本文档及本产品所有相
关的文档最终解释权归大疆TM创新（DJI）所有。如有更新，恕不另行通知。请访问 www.dji.
com 官方网站以获取最新的产品信息。

一旦使用本产品，即视为您已经仔细阅读本免责声明与警告，理解、认可和接受本声明全部条
款和内容。您承诺对使用本产品以及可能带来的后果负全部责任。您承诺仅出于正当目的使用
本产品，并且同意本条款以及大疆创新（DJI）制定的任何相关条例、政策和指引。

简  介

使用MANIFOLDTM 2 安装支架将Manifold 2 固定至MATRICETM 210 V2、Matrice 210 RTK

V2、Matrice 210 或 Matrice 210 RTK 飞行器，并连接相应线材。本文以安装至 Matrice 210 V2
/ Matrice 210 RTK V2 为例进行说明。

物品清单

安装支架×1 套 L 型扳手×1

×

螺丝 A（M2.5
螺丝 B（M1.6×4，十字）×4 XT30 电源线×1
螺丝 C（M2.5×14，内六角）×4

8，内六角）×10 双 A 口 USB 线×1

使  用

1. 如图 I，组装安装支架主体，拧紧 6 颗螺丝 A。

2. 如图 II，将安装支架中的 L 型固定块安装至 Manifold 2，拧紧 4 颗螺丝 A。

3. 如图 III，将 Manifold 2 和安装支架安装至飞行器上方，拧紧4 颗螺丝 B 和 4 颗螺丝 C。务

必按照图示方向安装，切勿装反。

4. 如图 IV，使用双 A 口 USB 线连接 Manifold 2 的 USB 3.0 接口（Type A）与飞行器尾部的
USB 接口，使用 XT30 电源线连接 Manifold 2 的电源接口至飞行器尾部的对外电源接口，然

后将连接线卡入支架上的护线扣。

5. 使用合适的线材连接飞行器尾部的扩展接口 3 至 Manifold 2 的 USB 3.0 接口或 UART 接口，
详情参考 Manifold 2 使用说明。（https://www.dji.com/manifold-2 ）

6. 使用 Manifold 2 时，将飞行器尾部的 USB 模式切换开关拨至右侧 。

切勿使线材遮挡飞行器顶部红外感知系统。
若使用 M210 V2 飞行器，还需要安装外置GPS 套件，详情参考外置 GPS 套件相关

文档。

若使用 M210 RTK V2 飞行器，安装完成后，注意整理 D-RTK 天线连接线，切勿使其

过度弯折。

浏览 http://www.dji.com/service 以获取产品的售后信息。
“DJI”表示深圳市大疆创新科技有限公司及其关联公司。