DeWalt DW820 User Manual

DW820

English (original instructions) 3

Copyright DEWALT

2

Figure 1

a

b

d

Figure 2

c

f

d

e

1

Figure 3A

c

Figure 3B

Figure 4

l

k

j

i

g

h

l

Figure 5

k

i

g

h

Figure 6

2

ANGLE GRINDER
DW820

ENGLISH

Congratulations!

You have chosen a DEWALT tool. Years of
experience, thorough product development and
innovation make DEWALT one of the most reliable
partners for professional power tool users.

Technical Data

DW820-ZA

Voltage VAC 230
Type 1
Power input W 680
No-load/rated speed min-1 11000
Wheel diameter mm 100
Grinding Wheel thickness mm 6
Wheel Type 27
Spindle diameter M10
Weight kg 1.87

Defi nitions: Safety Guidelines

The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.

DANGER: Indicates an imminently

hazardous situation which, if not avoided,
will result in death or serious injury.

WARNING: Indicates a potentially

hazardous situation which, if not
avoided, could result in death or
serious injury.

CAUTION: Indicates a potentially

hazardous situation which, if not
avoided, may result in minor or

moderate injury.

NOTICE: Indicates a practice not

related to personal injury which, if
not avoided, may result in property
damage.

Denotes risk of electric shock.

Denotes risk of fire.

WARNING: To reduce the risk of injury,

read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings

and all instructions. Failure to follow

the warnings and instructions may result
in electric shock, fire and/or serious
injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery­operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of
flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust
or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can
cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of
electric shock.

b) Avoid body contact with earthed or

grounded surfaces such as pipes,
radiators, ranges and refrigerators. There

is an increased risk of electric shock if your
body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will
increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the
risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

3

ENGLISH

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric
shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and

use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of

inattention while operating power tools may
result in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger

on the switch or energising power tools that
have the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.

e) Do not overreach. Keep proper

footing and balance at all times. This
enables better control of the power tool in
unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce

dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job
better and safer at the rate for which it
was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from
the power tool before making any

adjustments, changing accessories, or
storing power tools. Such preventive safety

measures reduce the risk of starting the
power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.

Power tools are dangerous in the hands of
untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.

g) Use the power tool, accessories and

tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for

operations different from those intended
could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a

qualified repair person using only identical
replacement parts. This will ensure that the

safety of the power tool is maintained.

ADDITIONAL SPECIFIC SAFETY RULES

Safety Instructions for All Operations

a) This power tool is intended to function

as a grinder. Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow

all instructions listed below may result in electric
shock, fire and/or serious injury.

b) Operations such as sanding, wire

brushing, polishing and cutting-off are not
recommended to be performed with this
power tool. Operations for which the power

tool was not designed may create a hazard and
cause personal injury.

c) Do not use accessories which are not

specifically designed and recommended
by the tool manufacturer. Just because the

accessory can be attached to your power tool,
it does not assure safe operation.

4

ENGLISH

d) The rated speed of the accessory must be at

least equal to the maximum speed marked
on the power tool. Accessories running faster

than their rated speed can break and fly apart.

e) The outside diameter and the thickness of

your accessory must be within the capacity
rating of your power tool. Incorrectly sized

accessories can not be adequately guarded or
controlled.

f) The arbour size of wheels, flanges, backing

pads or any other accessory must properly
fit the spindle of the power tool. Accessories

with arbour holes that do not match the
mounting hardware of the power tool will run
out of balance, vibrate excessively and may
cause loss of control.

g) Do not use a damaged accessory. Before

each use inspect the accessory such as
abrasive wheel for chips and cracks, backing
pad for cracks, tear or excess wear, wire
brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for
damage or install an undamaged accessory.
After inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run
the power tool at maximum no-load speed
for one minute. Damaged accessories will

normally break apart during this test time.

h) Wear personal protective equipment.

Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection must

be capable of stopping flying debris generated
by various operations. The dust mask or
respirator must be capable of filtrating particles
generated by your operation. Prolonged
exposure to high intensity noise may cause
hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area
must wear personal protective equipment.

Fragments of workpiece or of a broken
accessory may fly away and cause injury
beyond immediate area of operation.

j) Hold power tool by insulated gripping

surfaces only, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and
could give the operator an electrical shock.

k) Position the cord clear of the spinning

accessory. If you lose control, the cord may be
cut or snagged and your hand or arm may be
pulled into the spinning accessory.

l) Never lay the power tool down until the

accessory has come to a complete stop. The
spinning accessory may grab the surface and
pull the power tool out of your control.

m) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.

n) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside
the housing and excessive accumulation of
powdered metal may cause electrical hazards.

o) Do not operate the power tool near

flammable materials. Sparks could ignite these
materials.

p) Do not use accessories that require liquid

coolants. Using water or other liquid coolants
may result in electrocution or shock.

FURTHER SAFETY INSTRUCTIONS
FOR ALL OPERATIONS

Causes and Operator Prevention
of Kickback

Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory which in turn
causes the uncontrolled power tool to be forced in
the direction opposite of the accessory’s rotation at
the point of the binding.

For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward
or away from the operator, depending on direction
of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these
conditions.

Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given
below:

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control
over kickback or torque reaction during start

5

ENGLISH

up. The operator can control torque reaction or
kickback forces, if proper precautions are taken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over your
hand.

c) Do not position your body in the area where

power tool will move if kickback occurs.
Kickback will propel the tool in direction
opposite to the wheel’s movement at the point
of snagging.

d) Use special care when working corners,

sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or
kickback.

e) Do not attach a saw chain woodcarving

blade or toothed saw blade. Such blades
create frequent kickback and loss of control.

Safety Warnings Specifi c for
Grinding Operations

a) Use only wheel types that are recommended

for your power tool and the specific guard
designed for the selected wheel. Wheels for

which the power tool was not designed cannot
be adequately guarded and are unsafe.

b) The guard must be securely attached

to the power tool and positioned for
maximum safety, so the least amount of
wheel is exposed towards the operator. The

guard helps to protect the operator from broken
wheel fragments, accidental contact with wheel
and sparks that could ignite clothing.

c) Wheels must be used only for recommended

applications. For example: do not grind with
the side of cut-off wheel. Abrasive cut-off

wheels are intended for peripheral grinding, side
forces applied to these wheels may cause them
to shatter.

d) Always use undamaged wheel flanges

that are of correct size and shape for your
selected wheel. Proper wheel flanges support

the wheel thus reducing the possibility of wheel
breakage. Flanges for cut-off wheels may be
different from grinding wheel flanges.

e) Do not use worn down wheels from larger

power tools. Wheel intended for larger power
tool is not suitable for the higher speed of a
smaller tool and may burst.

Residual Risks

In spite of the application of the relevant safety
regulations and the implementation of safety

6

devices, certain residual risks cannot be avoided.
These are:

– Impairment of hearing.

– Risk of personal injury due to flying particles.

– Risk of burns due to accessories becoming hot

during operation.

– Risk of personal injury due to prolonged use.

– Risk of dust from hazardous substances.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

DATE CODE POSITION (FIG. 1)

The date code (e), which also includes the year of
manufacture, is printed into the housing.

Example:

2014 XX XX

Year of Manufacture

Package Contents

The package contains:

1 Angle grinder

1 Guard

1 Side handle

1 Flange set

1 Two pin spanner

1 Instruction manual

• Check for damage to the tool, parts or
accessories which may have occurred during
transport.

• Take the time to thoroughly read and
understand this manual prior to operation.

Description (fi g. 1)

WARNING: Never modify the power

tool or any part of it. Damage or
personal injury could result.

a. On/off switch

b. Spindle lock button

c. Guard

d. Side handle

ENGLISH

INTENDED USE

Your DW820 angle grinder has been designed for
professional grinding applications.

DO NOT use grinding wheels other than centre
depressed wheels and flap-disc.

DO NOT use under wet conditions or in presence of
flammable liquids or gases.

These heavy-duty angle grinders are professional
power tools. DO NOT let children come into
contact with the tool. Supervision is required when
inexperienced operators use this tool.

• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.

Electrical Safety

The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no
earth wire is required.

If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organisation.

Mains Plug Replacement
(Middle East and Africa)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in
the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see Technical Data). The minimum conductor
size is 1 mm2; the maximum length is 30 m.

When using a cable reel, always unwind the cable
completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk

of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before

reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.

Attaching Side Handle (fi g. 2)

WARNING: Before using the tool,

check that the handle is tightened
securely.

WARNING: The side handle should

always be used to maintain control of
the tool at all times.

Screw the side handle(d) tightly into one of the
holes (f) on either side of the gear case.

Mounting and Removing the Guard
(fi g. 3)

WARNING: To reduce the risk

of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before

reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.

CAUTION: Guards must be used with

this grinder.

TO MOUNT THE GUARD

1. Place the angle grinder on a table, spindle up.

2. Press the guard (c) down (fig. 3A).

3. Position the guard between your body and work
piece.

4. Tight the screw (l) holding the cinch collar
firmly around the neck of spindle (fig. 3B)

TO REMOVE THE GUARD

1. Loosen the screw (l) holding the cinch collar
around the neck of the spindle.

2. Lift up on the guard.

Fitting and Removing a Grinding Disc
(fi g. 1, 4, 5)

WARNING: Do not use a damaged

disc.

7

ENGLISH

1. Place the tool on a table, guard up.

2. Fit the backing flange(g) correctly onto the
spindle(h) (fig. 4).

3. Place the disc(i) on the flange(g). When fitting
a disc with a raised centre, make sure that the
raised centre(j) is facing the flange(g).

4. Screw the outer flange (k) onto the spindle(h)
(fig. 5). The ring on the flange (k) must face
towards the disc when fitting a grinding disc.

5. Press the spindle lock button(b) and rotate the
spindle(h) until it locks in position.

6. Tighten the flange (k) with the two pin spanner
supplied.

7. Release the spindle lock.

8. To remove the disc, loosen the flange (k) with
the two pin spanner.

Prior to Operation

• Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.

• Be sure the inner and outer flange are mounted
correctly.

• Make sure the disc or wheel rotates in the
direction of the arrows on the accessory and
the tool.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before

reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.

WARNING:

• Ensure all materials to be ground or

cut are secured in place.

• Apply only a gentle pressure to the

tool. Do not exert side pressure on the
disc.

• Avoid overloading. Should the tool

become hot, let it run a few minutes
under no load condition.

Proper Hand Position (fi g. 1, 6)

WARNING: To reduce the risk of

WARNING: To reduce the risk of

Proper hand position requires one hand on the side
handle(d), with the other hand on the body of the
tool, as shown in Figure 6.

serious personal injury, ALWAYS use
proper hand position as shown.

serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.

Switching On and Off (fi g. 1)

WARNING: Do not switch the tool on

WARNING: Before using the tool,

To start the tool, slide the on/off slider switch(a)
toward the front of the tool. To stop the tool, release
the on/off slider switch.
For continuous operation, slide the switch toward
the front of the tool and press the forward part of the
switch inward.
To stop the tool while operating in continuous mode,
press the rear part of the slider switch and release.

or off when under load.

check that the handle is tightened
securely.

Spindle Lock (fi g. 1)

The spindle lock(b) is provided to prevent the
spindle from rotating when installing or removing
wheels. Operate the spindle lock only when the tool
is turned off, unplugged from the power supply, and
has come to a complete stop.

NOTICE: To reduce the risk of damage

To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate
the spindle further.

to the tool, do not engage the spindle
lock while the tool is operating. Damage
to the tool will result and attached
accessory may spin off possibly
resulting in injury.

Metal Applications

When using the tool in metal applications, make
sure that a residual current device (RCD) has been
inserted to avoid residual risks caused by metal
swarf.

If the power supply is shut off by the RCD, take the
tool to an authorised DEWALT repair agent.

WARNING: In extreme working

conditions, conductive dust can

8

ENGLISH

accumulate inside the machine housing
when working with metal. This can
result in the protective insulation in the
machine becoming degraded with a
potential risk of an electrical shock.

To avoid build-up of metal swarf inside the machine,
we recommend to clear the ventilation slots on a
daily basis. Refer to Maintenance.

Using Flap Discs

WARNING: Metal dust build-up.

Extensive use of flap discs in metal
applications can result in the increased
potential for electric shock. To reduce
this risk, insert an RCD before use
and clean the ventilation slots daily by
blowing dry compressed air into the
ventilation slots inaccordance with the
below maintenance instructions.

MAINTENANCE

Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.

Pop-off Brushes

The motor will be automatically shut off indicating
that the carbon brushes are nearly worn out and that
the tool needs servicing. The carbon brushes are
not user-serviceable. Take the tool to an authorised

EWALT repair agent.

D

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

WARNING: Never use solvents or

the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.

other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth

dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.

Optional Accessories

WARNING: Since accessories, other

than those offered by DEWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DEWALT recommended
accessories should be used with this
product.

Consult your dealer for further information on the
appropriate accessories.

Protecting the Environment

Separate collection. This product must

not be disposed of with normal
household waste.

Should you find one day that your DEWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.

Separate collection of used products and

packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.

Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.

DEWALT provides a facility for the collection and
recycling of DEWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.

You can check the location of your nearest
authorised repair agent by contacting your local
DEWALT office at the address indicated in this
manual. Alternatively, a list of authorised DEWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.

9

101112

Afghanistan Ariana Hafiz Zabi Co. Ltd. [e-mail] Tel: [phone]
Dahan Bagh Squire Karte Ariana, Kabul, Afghanistan Fax: [phone]

Algeria Sarl Outillage Corporation [e-mail] Tel: [phone]
08, Rue Med Boudiaf (ex TELLA Achen) [e-mail] 213-0-21375131
Cheraga, Alger [e-mail]; Fax: [phone]
[e-mail]

Angola Angoferraria, Lda. [e-mail] Tel: [phone]
Rua Robert Shields, nº 61, Luanda, Angola [e-mail] Fax: [phone]

Azerbaijan Royalton Holdings Ltd. [e-mail] Tel: [phone]
41 Khagani St. Apt. 47 AZ1001 Baku- Azerbaijan [e-mail] Fax: [phone]

Egypt ElFarab S.A.E. [e-mail] Tel: [phone]
15-Nabil El Wakkad Street, Dokki, [e-mail] Fax: [phone]
Giza, Egypt [e-mail]

Ethiopia Seif Tewfik Sherif [e-mail] Tel: [phone]
Arada Sub City, Kebele 01/02, Global Insurance Bldg., [e-mail] 251-11-1563969
2nd Flr., Room 43, P.O. Box 2525, Addis Ababa Fax: [phone]

Iraq Al-Sard Co. for General Trading Ltd [e-mail] Tel: [phone]
Jbara Bldg. 3Flr. Al Rasheed St., Baghdad, Iraq

Jordan Amman West Stores-Bashiti [e-mail] Tel: [phone]
210 Garden St. Tla’a Ali, P.O. Box 1564 [e-mail] Fax: [phone]
Tla Ali Amman 11953, Jordan

Kenya Dextron Tools Ltd. [e-mail] Tel: [phone]
P.O. Box 20121-00200, Shariff House, [e-mail] 254-20-2358021
Kimathi Street, Nairobi Fax: [phone]

Lebanon Est. Shaya & Azar S.A.R.L. [e-mail] Tel: [phone]
Boulvard Jdeideh - Mar Takla - Bouchrieh . 961 1 872306
P.O. Box 90545, Jdeideh. Beirut – Lebanon Fax: [phone]

Libya North Africa Trading ( El Ghoul Brothers) [e-mail] Tel: [phone]
P.O. Box 348, 7 October Street 11 [e-mail] Fax: [phone]
Benghazi [e-mail]

North Africa Trading ( El Ghoul Brothers) [e-mail] Tel: [phone]
AlBarniq D
Mokhazin-elsukar St. ElFallah, Tripoli

North Africa Trading ( El Ghoul Brothers) Tel: [phone]
AlHilal Service Center Tawergha St., Misurata

Mauritius Robert Le Marie Limited [e-mail] Tel: [phone]
Old Moka Road, Bell Village, P.O. Box 161, [e-mail] 230-212 2847
Port Louis Fax: [phone]

Morocco Ets Louis Guillaud & Cie [e-mail] Tel: [phone] / 305971 / 317815 /
31, Rue Pierre Parent, [e-mail] 315576
Casablanca – 21000 Fax: [phone] / 317888

Nigeria Meridian Power Tools Ltd. [e-mail] Tel: [phone]
Gr. Floor, #1 Alhaji Masha Rd, Next toTeslim Balogun 234-1-7740410
Stadium, Near National Stadium Surulere, Lagos, Nigeria Fax: [phone]

Pakistan Northern Toolings (Pvt) Ltd.-Lahore [e-mail] Tel: [phone]
86- Railway Road, Lahore – 7 [e-mail] 92-423-7641675
Pakistan [e-mail] Fax: [phone]

Norther n Toolings (Pvt) Ltd.-Karachi [e-mail] Tel: [phone]
224-231 Industrial Town Plaza, Shahrah-e-Liaqat, 92-213-2465307
Karachi, Pakistan Fax: [phone]

Norther n Toolings (Pvt) Ltd.-Taxila [e-mail] Tel: [phone]
Al-Rehman Plaza, Opposite Tehsil Court, Fax: [phone]
Faisal Shaheed Road, Taxila

South Benray Tool Wholesalers C.C. [e-mail] Tel: [phone]
Africa 91 Turffontein Road, Stafford, Johannesburg, 2001 P.O. [e-mail] Fax: [phone]

Box 260037 EXCOM 2023, South Africa [e-mail]

Tanzania General Motors Investment Ltd. [e-mail] Tel: [phone] /
14 Vingunguti-Nyerere Road, P.O.Box 16541, [e-mail] 2862661 / 2862671 / 2862659
Dar es Salaam, Tanzania [e-mail] Fax: [phone]

Tunisia Ets. Mohamed Ghorbel [e-mail] Tel: [phone]
03 Rue 8603 Charguia I Tunis. [e-mail] 216-71793848
Postal Code 2035 [e-mail] Fax: [phone]

Uganda The Building Center (u) Ltd. [e-mail] Tel: [phone]
52 Station Road, Kitgum House, [e-mail] 256-041-4259754
P.O. Box 7436 Kampala, Uganda Fax: [phone]

Yemen Middle East Trading Co. (METCO) [e-mail] Tel: [phone]
5th Flr.Hayel Saeed Anam Bldg. [e-mail] Fax: [phone]
Al-Mugamma St. Taiz, [e-mail]
Yemen [e-mail]

Middle East Trading Co. (METCO) [e-mail] Tel: [phone]
Mualla Dakka, [e-mail] Fax: [phone]
Aden [e-mail]

Middle East Trading Co. (METCO) [e-mail] Tel: [phone]
Hayel st., Sana'a, [e-mail] Fax: [phone]
Yemen [e-mail]

EWALT Center, Fax: [phone]

UAE Black & Decker (Overseas) GmbH [e-mail] Tel: [phone]
P.O. Box 5420, Dubai Fax: [phone]

Ideal Star Workshop Eqpt. Trading LLC [e-mail] Tel: [phone]
P.O. Box 37116, Al Quoz, Dubai Fax: [phone]

Alebrah Engineering Service [e-mail] Tel: [phone]
P.O. Box 78954, Al Qusais, Dubai Fax: [phone]

Burj Al Madeena [e-mail] Tel: [phone]
Industrial Area No. 1, opp. Pakistani Masjid Fax: [phone]
P.O. Box 37635, Sharjah

McCoy Middle East LLC [e-mail] Tel: [phone]
P.O. Box 25793, Sharjah Fax: [phone]

McCoy Middle East LLC [e-mail] Tel: [phone]
P.O. Box 10584, Ras Al Khaimah Fax: [phone]

Al Sukoon Gen. Trdg. Co. LLC [e-mail] Tel: [phone]
P.O. Box 2975, Ajman Fax: [phone]

Zillion Equipment and Spare Parts Trading LLC [e-mail] Tel: [phone]
P.O. Box 19740, opp. Bin Sadal / Trimix Redymix Sanaiya, Al Ain Fax: [phone]

Light House Electrical, Abu Dhabi Branch [e-mail] Tel: [phone]
P.O. Box 120, Abu Dhabi Fax: [phone]

Light House Electrical, Musaffah Branch [e-mail] Tel: [phone]
P.O. Box 120, Abu Dhabi Fax: [phone]

Bahrain Alfouz Services Co. WLL [e-mail] Tel: [phone]
P.O. Box 26562, Tubli, Manama Fax: [phone]

Kavalani & Sons W.L.L. [e-mail] Tel: [phone]
P.O. Box 71, Sitra, Manama [e-mail] Fax: [phone]

Kuwait Al Omar Technical Co. [e-mail] Tel: [phone]
P.O. Box 4062, Safat 13041, Kuwait Fax: [phone]

Fawaz Al Zayani Establishment [e-mail] Tel: [phone]
P.O. Box 42426, Shop No.18, Fax: [phone]
Al Humaizi Commercial Complex, Khalifa Al Jassim, Shuwaikh

Fawaz Al Zayani Establishment [e-mail] Tel: [phone]
Fahaheel Industrial Area, Main St., Sanaya Fax: [phone]

Oman Al Jizzi Company LLC [e-mail] Tel: [phone]
P.O. Box 1704, P.C. 112, Ruwi [e-mail] Fax: [phone]

Al Hassan Technical & Construction Supplies Co. LLC [e-mail] Tel: [phone]
P.O. Box 1948, P.C. 112, Ruwi [e-mail] Fax: [phone]

Oman Hardware Co. LLC [e-mail] Tel: [phone]
P.O. Box 635, Ruwi Postal Code 112 Fax: [phone]

Khimji Ramdas [e-mail] Tel: [phone]
P.O. Box 19, Post Code 100, Ghala, Muscat Fax: [phone]

Qatar Teyseer Industrial Supplies & Services Co. WLL [e-mail] Tel: [phone]
55, Al Wakalat St. (Between St. 18 & 19) [e-mail] Fax: [phone]
Salwa Industrial Area, P.O. Box 40523 Doha

Shaheen Electrical Works & Trading Co. WLL [e-mail] Tel: [phone]
Gate 34, St. 44 Industrial Area P.O. Box 9756, Doha Fax: [phone]

KSA Industrial Material Organization (IMO) [e-mail] Tel: [phone] Ext. 26
P.O. Box 623, Rail Street, Riyadh Tel: [phone]
Fax: [phone]

Fawaz Ebrahim Al Zayani Trading Est. [e-mail] Tel: [phone]
P.O. Box 76026, Al Raka : 31952 Fax: [phone]

MSS (Al-Mojil Supply & Services) [e-mail] Tel: [phone]
P.O. Box 450, Jubail 31951 [e-mail] Tel: [phone]
Opp-Gulf Bridge Library & Riyadh House Fax: [phone]

EAC (Al Yousef Contg. & Trdg. Est.) [e-mail] Tel: [phone]
P.O. Box 30377, Jeddah -21477 Fax: [phone]

Mohamed Ahmed Bin Afif Est. [e-mail] Tel: [phone]
P.O. Box 530, Yanbu, Al Bahr Fax: [phone]

Garziz Trading for Bldg Mat & Decoration [e-mail] Tel: [phone]
P.O. Box 3364, Madina Fax: [phone]

Sultan Garment Factory (RSC) [e-mail] Tel: [phone]
P.O. Box 29912, Riyadh 11467 Fax: [phone]

Al Bawardi Tools & Hardware [e-mail] Tel: [phone] Ext. 24
P.O. Box 112, Dammam 31411 [e-mail] Tel: [phone] Ext. 24
Fax: [phone]

Al Bawardi Tools & Hardware [e-mail] Tel: [phone]
P.O. Box 68, Riyadh 11411 [e-mail] Fax: [phone]

Al Bawardi Tools & Hardware [e-mail] Tel: [phone]
P.O. Box 16905, Jeddah 21474 [e-mail] Tel: [phone]
Fax: [phone]

N413096 09/14