Desa Unvented Propane Gas Log Heater Split Oak User Manual

Page 1
DESA INTERNATIONAL
UNVENTED (VENT-FREE)
PROPANE GAS LOG HEATER
Manually Control Models Also Designed Certified as Vented Decorative Appliance
This appliance may be installed in an aftermarket* manufactured (mobile) home,
where not prohibited by state or local codes.
OWNER’S OPERATION AND INSTALLATION MANUAL
SPLIT OAK DESIGN
®
AMERICAN OAK DESIGN
LO
PILOT OFF HI
18", 24", and 30"
(“B” Models) Variable Manually-Controlled
and (“A” Models) Thermostatically Controlled
WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appli­ance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your build­ing.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas sup­plier, call the fire department.
Installation and service must be performed by a qualified installer, ser­vice agency, or the gas supplier.
LO
PILOT OFF HI
18", 24", and 30"
Variable Manually-Controlled
WARNING: Improper installation, adjust­ment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual for correct installa­tion and operational procedures. For as­sistance or additional information con­sult a qualified installer, service agency, or the gas supplier.
WARNING: This gas log set is for installa­tion in a masonry solid fuel burning fire­place, a U.L. listed manufactured solid fuel burning fireplace or an AGA design certified vent-free firebox or stove (in­cluding LogMate™ Series) listed for use with these gas log models .
WARNING: This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to “Air for Com­bustion and Ventilation” section in this manual.
Save this manual for future reference.
Page 2
UNVENTED PROPANE GAS LOG HEATER
SAFETY INFORMATION
WARNINGS
IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, oper­ate, or service this heater. Im­proper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.
DANGER: Carbon monoxide
poisoning may lead to death!
Carbon Monoxide Poisoning: Early
signs of carbon monoxide poisoning re­semble the flu, with headaches, dizziness, or nausea. If you have these signs, the heater may not be working properly. Get fresh air at once! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the influence of alcohol, and those at high altitudes.
Propane Gas: Propane gas is odorless. An odor-making agent is added to the gas. The odor helps you detect a gas leak. How­ever, the odor added to the gas can fade. Gas may be present even though no odor exists.
Make certain you read and understand all Warnings. Keep this manual for reference. It is your guide to safe and proper operation of this heater.
WARNING: Any change to this heater or its controls can be dan­gerous.
1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.
2. Do not place propane supply tank(s) inside any structure. Locate propane supply tank(s) outdoors.
3. If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not use any phone in your build­ing
• immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions
• if you cannot reach your gas supplier, call the fire department
4. This heater shall not be installed in a bed­room or bathroom, unless installed as a vented appliance (Variable Manually­Controlled models only , see page 8).
5. Never install the heater
• in a recreational vehicle
• where curtains, furniture, clothing, or
other flammable objects are less than 36 inches from the front, top, or sides of the heater
• in high traffic areas
• in windy or drafty areas
6. Before installing in a solid fuel burn­ing fireplace, the chimney flue and fire­box must be cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner. Creosote will ignite if highly heated. Inspect chimney flue for damage. If damaged, operate heater with flue damper closed.
7. If fireplace has glass doors, never op­erate this heater with glass doors closed. If you operate heater with doors closed, heat buildup inside fireplace will cause glass to burst. Also if fireplace open­ing has vents at the bottom, you must open the vents before operating heater.
8. Y ou must operate this heater with a fire­place screen in place. Make sure fire­place screen is closed before running heater.
9. This log heater is designed to be smoke­less. If logs ever appear to smoke, turn off heater and call a qualified service person. slight smoking may occur due to log curing and heater burning manufactur­ing residues.
10. Do not allow fans to blow directly into the fireplace. Avoid any drafts that al­ter burner flame patterns. Ceiling fans may create drafts that alter burner flame patterns. Altered burner patterns can cause sooting.
Note:
During initial operation,
11. Do not use a blower insert, heat ex­changer insert or other accessory not approved for use with this heater.
12. This heater needs fresh, outside air ven­tilation to run properly . This heater has an oxygen depletion sensor (ODS) pi­lot light safety system. The ODS shuts down the heater if not enough fresh air is available. See Air for Combustion and V entilation, pages 4 and 5. If heater keeps shutting off, see Troubleshoot- ing, pages 18 through 20.
13. Do not run heater
• where flammable liquids or vapors
are used or stored
• under dusty conditions
14. Do not use this heater to cook food or burn paper or other objects.
15. Never place any objects on the heater.
16. Heater base assembly becomes very hot when running heater. Keep children and adults away from hot surface to avoid burns or clothing ignition. Heater will remain hot for a time after shutpdown. Allow surface to cool before touching.
17. Carefully supervise young children when they are in the room with heater.
18. Do not use heater if any part has been exposed to or under water. Immediately call a qualified service technician to inspect the room heater and to replace any part of the control system and any gas control which has been under wa­ter.
19. Do not operate heater if any log is bro­ken. Do not operate heater if a log is chipped (dime-sized or larger).
20. Turn heater off and let cool before ser ­vicing. Only a qualified service person should service and repair heater.
21. Operating heater above elevations of 4,500 feet may cause pilot outage.
22. To prevent performance problems, do not use propane fuel tank of less than 100 lb. capacity.
2
103427
Page 3
SPLIT OAK AND AMERICAN OAK DESIGN
18", 24" AND 30" MODELS
PRODUCT IDENTIFICATION
Top Middle Log
Left Front Branch
Piezo Ignitor
Front Burner
Right Front Branch
Control Knob
Figure 1 - Split Oak Design Model
Front Log
Left Front Branch
Crossover Log
Crossover Log
Rear Log
Rear Burner
Bottom Middle Log
Base Assembly
Rear Log
Rear Burner
LOCAL CODES
Install and use heater with care. Follow all local codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code ANSI Z223, also known as NFPA 54*.
*Available from: American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
Note:
Where listed vented decorative logs are required, thermostat operation is not permitted.
UNPACKING
1. Remove logs and heater base assem-
bly from carton. heater base assembly by burners. This could damage heater. Always handle base assembly by grate.
2. Remove all protective packaging ap-
plied to logs and heater for shipment.
3. Check all items for any shipping dam-
age. If damaged, promptly inform dealer where you bought heater.
Note:
Do not pick up
PRODUCT FEATURES
Operation
This heater is clean burning. It requires no outside venting. There is no heat loss out a vent or up a chimney. Heat is generated by both realistic flames and glowing coals. This heater is designed for vent-free opera­tion with flue damper closed. State and local codes in some areas prohibit the use of vent­free heaters. You can operate heater as a vented product by opening flue damper.
Piezo Ignitor
Front Burner
Base Assembly
Control Knob
Figure 2 - Standard Oak Design Model
103427
Right Front Branch
3
Safety Device
This heater has a pilot with an Oxygen Depletion Sensor Shutoff System (ODS). The ODS/pilot is a required feature for vent­free room heaters. The ODS/pilot shuts off the heater if there is not enough fresh air.
Piezo Ignition System
This heater has a piezo ignitor. This system requires no matches, batteries, or other sources to light heater.
Page 4
UNVENTED PROPANE GAS LOG HEATER
AIR FOR COMBUSTION AND VENTILATION
WARNING: This heater shall not be installed in a confined space unless provisions are pro­vided for adequate combustion and ventilation air. Read the fol­lowing instructions to insure proper fresh air for this and other fuel-burning appliances in your home.
Today’s homes are built more energy effi­cient than ever. New materials, increased insulation, and new construction methods help reduce heat loss in homes. Home own­ers weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as pos­sible.
While it is good to make your home energy efficient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper com­bustion and ventilation.
Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances draw air from the house to operate. You must provide ad­equate fresh air for these appliances. This will insure proper venting of vented fuel­burning appliances.
PROVIDING ADEQUATE VENTILATION
The following is exerpts from National Fuel Gas Code. NFPA 54/ANSI Z223.1, Section
5.3, Air for Combustion and Ventilation.
All spaces in homes fall into one of the three following ventilation classifications:
1. Unusually Tight Contruction; 2. Uncon­fined Space; 3. Confined Space.
The information on pages 4 and 5 will help you classify your space and provide ad­equate ventilation.
Unusually Tight Construction
The air that leaks around doors and win­dows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.
Unusually tight construction is de­fined as construction where:
a. walls and ceilings exposed to the
outside atmosphere have a con­tinuous water vapor retarder with a rating of one perm (6 x 10 per-pa-sec-m2) or less with open­ings gasketed or sealed
b. weather stripping has been
added on openable windows and doors
c. caulking or sealants are applied
to areas such as joints around window and door frames, be­tween sole plates and floors, be­tween wall-ceiling joints, be­tween wall panels, at penetra­tions for plumbing, electrical, and gas lines, and at other openings.
If your home meets all of the three criteria above, you must provide ad­ditional fresh air. See
From Outdoors
If your home does not meet all of the three criteria above, proceed to
and
, page 5
Ventilation Air
.
and
-11
kg
De­termining Air Flow For Heater Loca­tion
.
Confined and Unconfined Space
The National Fuel Gas Code (ANSIZ2123.1, 1992 Section 5.3) defines a confined space
as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are in­stalled*, through openings not furnished with doors, are considered a part of the unconfined space.
* Adjoining rooms are communicating only if there are doorless passageways or ventila­tion grills between them.
DETERMINING AIR FLOW FOR HEATER LOCATION
Determining if You Have a Confined or Unconfined Space
Use this work sheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between the rooms.
1. Determine the volume of the space (length x width x height).
Length x Width x Height =
__________ cu. ft. (volume of space)
Example:
20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or open­ings, add the volume of these rooms to the total volume of the space.
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
__________ (volume of space) ÷ 50
cu. ft. = (Maximum Btu/Hr the space can support)
Example:
space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space can sup­port)
3. Add the Btu/Hr of all fuel burning ap­pliances in the space.
Vent-free heater __________ Btu/Hr Gas water heater* ________ Btu/Hr Gas furnace _____________ Btu/Hr
Vented gas heater_________ Btu/Hr Gas fireplace logs ________ Btu/Hr Other gas appliances*+ ____ Btu/Hr Total = ____ Btu/Hr
Example:
Gas water heater 40,000 Btu/Hr Vent-free heater + 33,000 Btu/Hr Total = 73,000 Btu/Hr * Do not include direct-vent gas appli-
ances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.
Space size
2560 cu. ft. (volume of
Continued
4
103427
Page 5
SPLIT OAK AND AMERICAN OAK DESIGN
18", 24" AND 30" MODELS
AIR FOR COMBUSTION AND VENTILATION
Continued
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
________ Btu/Hr (maximum the
space can support)
________ Btu/Hr (actual amount of
Btu/Hr used)
Example:
The space in the above example is a con­fined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:
A. Rework worksheet, adding the space of
an adjoining room. If the extra space provides an unconfined space, remove door to adjoining room or add ventila­tion grills between rooms. See Ventila- tion Air From Inside Building.
B. V ent room directly to the outdoors. See
Ventilation Air From Outdoors.
C. Install a lower Btu/Hr heater, if lower
Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no additional fresh air ventilation.
51,200 Btu/Hr (maximum
the space can support) 73,000 Btu/Hr (actual
amount of Btu/Hr used)
VENTILATION AIR
Ventilation Air From Inside Building
This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor on the wall connecting the two spaces (see options 1 and 2, Figure 3). You can also remove door into adjoining room (see option 3, Figure 3). Follow the National Fuel Gas Code NFPA 54/ANSI Z223.1, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.
WARNING: Rework worksheet, adding the space of the adjoining unconfined space. The combined spaces must have enough fresh air to supply all appliances in both spaces.
12"
Ventilation
Grills
Into Adjoining
Room,
Option 1
Figure 3 - Ventilation Air from Inside Building
Or
Remove Door into Adjoining
Room, Option
3
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces.
IMPORTANT:
thermostat-controlled power vent. Heated air entering the attic will activate the power vent.
Do not provide openings for inlet or outlet air into attic if attic has a
Ventilation Grills
Into Adjoining Room,
Option 2
12"
WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space, provide ad­equate combustion and ventila­tion air by one of the methods described in the
National Fuel Gas Code, ANSI Z223.1, 1992, Section 5.3.
103427
Outlet Air
Outlet Air
Inlet Air
Inlet Air
Figure 4 - Ventilation Air from Outdoors
5
Ventilated Attic
Ventilated
Crawl Space
To Attic
To
Crawl
Space
Page 6
UNVENTED PROPANE GAS LOG HEATER
42"
16"
INSTALLATION
NOTICE: A qualified service per­son must install heater. Follow all local codes.
NOTICE: State or local codes may only allow operation of this appli­ance in a vented configuration. Check your state or local codes.
WARNING: Before installing in a solid fuel burning fireplace, the chimney flue and firebox must be cleaned of soot, creosote, ashes and loose paint by a quali­fied chimney cleaner. Creosote will ignite if highly heated. In­spect chimney flue for damage. If damaged, operate heater with flue damper closed.
WARNING: Seal any fresh air vents or ash clean-out doors lo­cated on floor or wall of fireplace. If not, drafting may cause pilot outage or sooting. Use a heat­resistant sealant. Do not seal chimney flue damper.
WARNING: Never install the heater
• in a bedroom or bathroom un-
less installed as a vented ap­pliance, see page 8
• in a recreational vehicle
• where curtains, furniture,
clothing, or other flammable objects are less than 36 inches from the front, top, or sides of the heater
• in high traffic areas
• in windy or drafty areas
CAUTION: This heater cre­ates warm air currents. These currents move heat to wall sur­faces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities in the air (such as tobacco smoke) exist, may discolor walls.
IMPORTANT:
ture to the air. Although this is beneficial, installing heater in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Com- bustion and Ventilation, pages 4 and 5.
Vent-free heaters add mois-
CHECK GAS TYPE
Use only propane gas. If your gas supply is not propane, do not install heater. Call dealer where you bought heater for proper type heater.
INSTALLATION AND CLEARANCES
(Vent-Free Operation Only)
WARNING: Maintain the mini­mum clearances. If you can, pro­vide greater clearances from floor, ceiling, and adjoining wall.
MINIMUM FIREPLACE CLEARANCE TO COMBUSTIBLE MATERIALS
Log Size 18", 24", 30" Side Wall 16" Ceiling 42" Floor 5"
LOG SIZING REQUIREMENTS
Log Minimum Firebox Size Size Height Depth Front Width
18" 17" 14" 20" 24" 17" 14" 26" 30" 17" 14" 32"
Carefully follow the instructions below. This will ensure safe installation into a masonry or U.L. listed manufactured fireplace.
Minimum Wall and Ceiling Clearances (see Figure 5)
A. Clearances from the side of the fire-
place opening to any combustible wall should not be less than 16 inches.
B. Clearances from the top of the fireplace
opening to the ceiling should not be less than 42 inches.
Figure 5 - Minimum Clearance to Wall and Ceiling
NOTICE: Manual control heaters may be used as a vented product. If so, you must always run heater with chimney flue damper open. If running heater with damper open, non-combustible material above fireplace opening is not needed. Go to
Installing Damper Clamp Accessory for Vented Operation,
page 8.
Minimum Non Combustible Material Clearances
If Not Using Mantel
Note:
If using a mantel, go to page 7. If not using a mantel, follow the information on this page.
You must have non combustible material(s) above the fireplace opening. Non combus­tible materials (such as slate, marble, tile, etc.) must be at least 1/2 inch thick. With sheet metal, you must have non combustible material behind it. Non combustible mate­rial must extend at least 8" up (for all mod­els). If non combustible material is less than 12", you must install the fireplace hood accessory (24" and 30" models only). See chart on page 7, column 1 and Figure 5 for minimum clearances.
IMPORTANT:
minimum clearances, you must operate heater with chimney flue damper open. Go to Installing Damper Clamp Accessory for Vented Operation, page 8.
If you cannot meet these
Continued
6
103427
Page 7
SPLIT OAK AND AMERICAN OAK DESIGN
Minimum Non­Combustible Material
Minimum Non­Combustible Material Height
Distances to Underside of Mantel
Top of Fireplace Opening
Underside of Mantel Shelf
12" 8"
(A)
20" 14"
24
1
/2
"
16
3
/4
"
27
1
/2
"
18
1
/2
"
30" 20"
All minimum distances are in inches
Log Set
24"/30" Models 18" Model
2
1
/2
"
6"
8"
10"
18", 24" AND 30" MODELS
INSTALLATION
Continued
Noncombustible Requirements for Material Distance (A) Safe Installation
12" or more Noncombustible material OK. Between 8" and 12" 24" or 30" Models: Install fireplace hood accessory
(GA6050 or GA6052, see 18" Model: Noncombustible material OK.
Less than 8" Noncombustible material must be extended to at
least 8". See
Between 8" and 12",
cannot extend material, you must operate heater with flue damper open.
Accessories,
above. If you
page 23).
Heat Resistant Material
(A)
Minimum Noncombustible Material Clearances If Using Mantel
You must have noncombustible material(s) above the fireplace opening. Noncombustible materials (such as slate, marble, tile, etc.) must be at least 1/2 inch thick. With sheet metal, you must have noncombustible material behind it. Noncombustible material must extend at least 8 inches up (for all models). If noncombustible material is less than 12", you must install the fireplace hood accessory (24" and 30" models only). Even if noncombustible material is more than 12", you may need the hood accessory to deflect heat away from your mantel shelf. See chart below and Figures 7 and 8 (page 8) for minimum clearances.
IMPORTANT:
chimney flue damper open. Go to Installing Damper Clamp Accessory for Vented Opera­tion, page 8.
Noncombustible Requirements for Material Distance (A) Safe Installation
12" or more Noncombustible material OK. Between 8" and 12" 24" or 30" Models: Install fireplace hood accessory
Less than 8" Noncombustible material must be extended to at
If you cannot meet these minimum clearances, you must operate heater with
(GA6050 or GA6052, see
Accessories,
page 23).
18" Model: Noncombustible material OK.
least 8". See
Between 8" and 12",
above. If you cannot extend material, you must operate heater with flue damper open.
Figure 6 - Heat Resistant Material (Slate, Marble, Tile, etc.) Above Fireplace
Mantel Shelf
Mantel Clearances
In addition to meeting non-combustible material clearances, you must also meet required clearances between fireplace open­ing and mantel shelf. If you do not meet the clearances losted below, you will need a hood.
Determining Minimum Mantel Clearance
If you meet minimum clearance between mantel shelf and top of fireplace opening, a hood is not required (see Figure 7).
103427
Continued
Figure 7 - Minimum Mantel Clearances Without Using Hood
7
Page 8
UNVENTED PROPANE GAS LOG HEATER
INSTALLATION
Continued
Determining Minimum Mantel Clearance When Using a Hood
If above minimum clearances are not met, you must have a hood. Follow minimum clearances shown in Figure 8 when using hood.
12" 10" 8" 6"
1
"
/2
2
Minimum Non­Combustible Material
8" Min.
Hood (GA6050, GA6052)
Figure 8 - Minimum Mantel Clearances When Using Hood
If your installation does not meet the above minimum clearances, you must:
• operate the logs only with the flue damper open, OR
• raise the mantel to an acceptable height, OR
• remove the mantel.
Floor Clearances
A. If installing appliance on the floor level,
you must maintain the minimum dis­tance of 14" to combustibles (see Fig­ure 9).
Mantel Shelf
Underside of Mantel Shelf
All minimum distances are in inches
Log Sets
12" 15" 18"
Distances to Underside of Mantel
18", 24",
20"
& 30" Models
Top of Fireplace Opening
Hearth
5" Min.
Combustible Material
Figure 10 - Minimum Fireplace Clearances Above Combustible Flooring
INSTALLING DAMPER CLAMP ACCESSORY FOR VENTED OPERATION
If reasons number 1 or 2 above apply to you, you must permanently open chimney flue damper. You must install the damper clamp accessory (to order, see Accessories, page
23). This will insure vented operation (see Figure 11). The damper clamp will keep damper open. Installation instructions are included with clamp accessory.
See chart below for minimum permanent flue opening you must provide. Attach damper clamp so the minimum permanent flue opening will be maintained at all times.
Area of Various Standard Round Flues
Diameter (ins.) Area (sq. ins.)
5" 20 sq. inches 6" 29 sq. inches 7" 39 sq. inches 8" 51 sq. inches
Chimney Minimum Permanent
Height (ft.) Flue Opening (sq. ins.)
6' to 15' 39 sq. inches
15' to 30' 29 sq. inches
Damper Clamp
Damper
Damper
Damper
Clamp
Combustible
14" Min.
Material
Non-Combustible Material
Figure 9 - Minimum Fireplace Clearances If Installed at Floor Level
B. If combustible materials are less than
14" to the fireplace, you must install ap­pliance at least 5" above the combus­tible flooring (see Figure 10).
Note:
When used as a vented heater, appli­ance must be installed only in a solid-fuel burning fireplace with a working flue and constructed of non combustible material.
If your heater is a manually controlled model, you may use this heater as a vented product. There are three reasons for operating your heater in the vented mode.
1. The fireplace does not meet the clear-
ance to combustibles requirements for vent-free operation.
2. State or local codes do not permit vent-
free operation.
3. You prefer vented operation.
8
Masonry Fireplace
Damper
Manufactured Fireplace
Figure 11 - Attaching Damper Clamp
Continued
103427
Page 9
SPLIT OAK AND AMERICAN OAK DESIGN
18", 24" AND 30" MODELS
INSTALLATION
Continued
INSTALLING HEATER BASE ASSEMBLY
WARNING: You must secure this heater to fireplace floor. If not, heater will move when you adjust controls. Moving heater may cause a gas leak.
WARNING: If installing in a sunken fireplace, special care is needed. You must raise the fire­place floor to allow access to heater control panel. This will in­sure adequate air flow and guard against sooting. Raise fireplace floor with non-combustible ma­terial. Make sure material is se­cure.
CAUTION: Do not pick up heater base assembly by burn­ers. This could damage heater. Only handle base assembly by grates.
1. Apply pipe joint sealant lightly to male threads of gas fitting (not provided). Connect approved flexible gas hose to gas regulator of heater (see Figure 12).
IMPORT ANT :
wrench when connecting flexible gas hose.
2. Locate mounting brackets, bolts, and nuts in hardware package. Attach mounting brackets to heater base (see Figure 13). Attach nuts finger tight.
3. Position heater base assembly in fire­place.
Flexible Gas Hose (if allowed by local codes)
Figure 12 - Attaching Flexible Gas Hose to Heater Gas Regulator
Hold gas regulator with
4. Mark screw locations through holes in mounting brackets. If installing in a brick-bottom fireplace, mark screw lo­cations in mortar joint of bricks.
5. Remove heater base from fireplace. Remove mounting brackets from heater base.
6. Drill holes at marked locations using 3/16" drill bit.
7. Attach mounting brackets to fireplace floor using masonry screws (in hard­ware package).
8. Reattach heater base to mounting brackets. Tighten nuts firmly.
9. Connect to gas supply. See Connect- ing To Gas Supply, page 10.
Heater Gas Regulator
CAUTION: Do not remove the metal data plates attached to the heater base assembly. The data plates contain important warranty information.
IMPORTANT:
ers are level. If heater is not level, heater will not work properly. For thermostat models, avoid damage to thermostat bulb. Avoid nicks or sharp bends in thermostat bulb wire. Keep thermostat bulb in mounting bracket.
Make sure the heater burn-
Installation Items Needed
• hardware package (provided with heater)
• approved flexible gas hose and fittings (not provided) (if allowed by local codes)
• sealant (resistant to LP gas, not provided)
• electric drill with 3/16" masonry drill bit
Mounting Bracket Screw
Mounting Bracket Nut
Figure 13 - Attaching Heater to Fireplace Floor
Masonry Screw
Mounting Bracket
Continued
103427
9
Page 10
UNVENTED PROPANE GAS LOG HEATER
INSTALLATION
Continued
CONNECTING TO GAS SUPPLY
NOTICE: A qualified service per­son must connect heater to gas supply. Follow all local codes.
CAUTION: Never connect heater directly to the propane supply. This heater requires an external regulator (not supplied). Install the external regulator be­tween the heater and propane supply.
Installation Items Needed
Before installing heater, make sure you have the items listed below.
• external regulator (supplied by installer, see below)
• piping (check local codes)
• sealant (resistant to LP gas)
• manual shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
* An A.G.A. design-certified manual shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Pur­chase the optional A.G.A. design-certified manual shutoff valve from your dealer. See Accessories, page 23.
The installer must supply an external regu­lator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11 and 14 inches of water. If you do not reduce incom­ing gas pressure, heater regulator damage could occur. Install external regulator with the vent pointing down as shown in Figure
14. Pointing the vent down protects it from
freezing rain or sleet.
Propane Supply Tank
External Regulator
Installation must include a manual shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 15).
Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe
Vent Pointing Down
Figure 14 - External Regulator With Vent Pointing Down
WARNING: Never connect heater to private (non-utility) gas wells. This gas is commonly known as wellhead gas.
could result in clogged heater valves.
CAUTION: Use pipe joint seal­ant that is resistant to liquid pe­troleum (LP) gas.
Install sediment trap in supply line as shown in Figure 15. Locate sediment trap where it is within reach for cleaning. Locate sedi­ment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap
CAUTION: Use only new,
black iron or steel pipe. Inter-
is not installed or is installed wrong, heater may not run properly.
nally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to heater. If
CAUTION: Avoid damage to
regulator. Hold gas regulator with wrench when connecting it to gas piping and/or fittings.
pipe is too small, undue loss of pressure will occur.
A.G.A. Design-Certified Manual Shutoff Valve With 1/8" NPT Tap*
From External Regulator (11" W.C.** to 14" W.C. Pressure)
Tee Joint Pipe
Nipple Cap
Sediment Trap
3" Minimum
Approved Flexible Gas Hose (if allowed by local codes)
Gas Regulator
* Purchase the optional A.G.A. design-certified manual shutoff valve from your dealer. See Accessories, page 23.
** Minimum inlet pressure for purpose of input adjustment.
Figure 15 - Gas Connection
10
Continued
103427
Page 11
SPLIT OAK AND AMERICAN OAK DESIGN
18", 24" AND 30" MODELS
INSTALLATION
Continued
CHECKING GAS CONNECTIONS
WARNING: Test all gas pip­ing and connections for leaks after installing or servicing. Cor­rect all leaks at once.
WARNING: Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once.
CAUTION: Make sure exter­nal regulator has been installed between propane supply and heater. See guidelines under Con­necting to Gas Supply, page 10.
Test Pressures Equal To or Less Than 1/2 PSIG
1. Close manual shutoff valve (see Fig­ure 16).
2. Pressurize supply piping system by ei­ther using compressed air or opening propane supply tank valve.
3. Check all joints from propane supply tank to manual shutoff valve (see Fig­ure 16). Apply mixture of liquid soap and water to gas joints. Bubbles form­ing show a leak.
4. Correct all leaks at once.
Pressure Testing Heater Gas Connections
1. Open manual shutoff valve (see Fig­ure 16).
ON
Open
POSITION
Manual Shutoff Valve
2. Open propane supply tank valve.
3. Make sure control knob of heater is in the OFF position.
4. Check all joints from manual shutoff valve to thermostat gas valve (thermo­stat-controlled models) or control valve (manually-controlled models) (see Fig­ure 16). Apply mixture of liquid soap and water to gas joints. Bubbles form­ing show a leak.
5. Correct all leaks at once.
6. Light heater (see Operating Heater, pages 14 through 16). Check all other internal joints for leaks.
7. Turn off heater (see To Turn Off Gas to Appliance, page 15 [thermostat-
controlled models] or page 16 [manu­ally-controlled models]).
Pressure Testing gas Supply Piping system
Test Pressures In Excess Of 1/2 PSIG
1. Disconnect heater and its individual manual shutoff valve from gas supply piping system. Pressures in excess of 1/2 psig will damage heater regulator.
2. Cap off open end of gas pipe where manual shutoff valve was connected.
3. Pressurize supply piping system by ei­ther using compressed air or
opening propane supply tank valve.
4. Check all joints of gas supply piping system. Apply mixture of liquid soap and water to gas joints. Bubbles form­ing show a leak.
5. Correct all leaks at once.
6. Re-connect heater and manual shutoff valve to gas supply. Check re-con­nected fittings for leaks.
Figure 16 - Manual Shutoff Valve
Propane Supply Tank
Figure 17 - Checking Gas Joints
OFF
POSITION
Closed
Manual Shutoff Valve
Thermostat Gas Valve or Control Valve Location
103427
Continued
11
Page 12
UNVENTED PROPANE GAS LOG HEATER
INSTALLATION
Continued
INSTALLING LOGS (American Oak Design Models)
WARNING: Failure to posi­tion the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal in­jury.
Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.
1. Slide rear log (#1) into place behind rear burner (see Figure 18).
2. Slide front log (#2) into place behind front burner. Make sure tabs at bottom of log are behind front burner (see Fig­ure 19).
3. Place crossover log (#3) into place (see Figure 20). Be sure to place back of crossover log into notch on left side of rear log. The indentation under front right fork of crossover log must rest on rectangular knob of front log.
4. Place left front branch (#4) and right front branch (#5) (24" and 30" mod­els) or front branch (#4) (18" model) into place (see Figure 21). Make sure notches on bottom rest on grates.
5. Add lava rock around base of heater.
Rear Log (#1)
Figure 18 - Installing Rear Log
Crossover Log (#3)
Figure 20 - Installing Crossover Log
Front Log (#1L)
Front Log (#1R)
Notch
Front Log (#2)
Tab
Figure 19 - Installing Front Log
Left Front Branch (#4) (24" & 30" models) or Front Branch (#4)
Notches
Notches
Figure 21 - Installing Left Front Branch and Right Front Branch
(18" Model)
Right Front Branch (#5)
Grate Prongs
Metal Grate Bar
Figure 22 - Installing Front Logs (#1L and #1R)
12
Continued
103427
Page 13
SPLIT OAK AND AMERICAN OAK DESIGN
INSTALLATION
Continued
INSTALLING LOGS (Split Oak Design Models)
WARNING: Failure to posi­tion the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal in­jury.
Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.
1. Place front logs (#1L and #1R) on top of the grate. Make sure the notches in the bottom of the logs fit over the grate prongs (see Figure 22, page 12). Push back of logs flush with metal grate bar.
Note:
18" model has only one front log.
2. Rest bottom middle log (#2) behind metal posts on front burner. Make sure the grooves in the bottom of the log fit over the grate. Bring the log forward next to the metal posts. The pegs on the log must be on top (see Figure 23).
3. Slide the grooves in the back of the rear log (#3) against the rear grate prongs. Make sure the peg on the log is on top (see Figure 24).
4. Place the top middle log (#4) on the bottom middle log (#2). Make sure the pegs of the bottom middle log fit se­curely in the holes of the top middle log (see Figure 25).
5. Place the crossover log (#5) on the back log and the top middle log. Make sure the peg on the rear log is in the hole in the bottom of the crossover log. The crossover log should fit in the cutout of the top middle log (see Figure 26).
18", 24" AND 30" MODELS
Peg
Groove Metal Post
Groove
Metal Post
Figure 23 - Installing Bottom Middle Log (#2)
Groove in Back of Log
Grate Prong
Rear Burner
Figure 24 - Installing Rear Log (#3)
Bottom Middle Log (#2)
Grate
Peg
Rear Log (#3)
Top Middle Log (#4)
Hole
Peg
Peg
Figure 25 - Installing Top Log (#4)
Crossover Log (#4)
Cutout Groove in Back of Log
Grate Prong
Figure 26 - Installing Crossover Log (#5)
Hole
Bottom Middle Log
Hole
Peg
103427
13
Page 14
UNVENTED PROPANE GAS LOG HEATER
OPERATING HEATER
Thermostat-Controlled Models
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING: If you do not fol­low these instructions exactly, a fire or explosion may result caus­ing property damage, personal injury or loss of life.
A. This appliance has a pilot which must
be lighted by hand. When lighting the pilot, follow these instructions ex­actly.
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your build­ing.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas sup­plier, call the fire department.
C. Use only your hand to push in or turn
the gas control knob. Ne ver use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part
has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been un­der water.
LIGHTING
INSTRUCTIONS
WARNING:
• If fireplace has glass doors, never operate this heater with glass doors closed. If you op­erate heater with doors closed, heat buildup inside fireplace will cause glass to burst. Also if fireplace opening has vents at the bottom, you must open the vents before operating heater.
• You must operate this heater with a fireplace screen in place. Make sure fireplace screen is closed before running heater.
NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orange flame will also be present. Open damper or window to vent smell. This will only last a few hours.
Note:
Homeowners generally prefer to operate their heater with the chimney damper closed. This will put all the heat into the room. However there may be times you will desire the full flames of the Hi heat setting but will find the heat output excessive. You can open the chim­ney damper (if you have one) fully or partially to release some of the heat. WARNING: Damper handle will be hot if heater has been running.
1. STOP! Read the safety information
above.
2. Make sure manual shutoff valve is
fully open.
3. Tur n control knob clockwise
to the OFF position.
Ignitor Button
Figure 27 - Control Knob and Ignitor Button Location
Clockwise
Control Knob
4. Wait f ive (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety in­formation above. If you don’t smell gas, go to the next step.
5. T urn contr ol knob counterclockwise
C-clockwise
to the PILOT position. Press in control knob for f ive (5) sec­onds (see above).
Note:
You may be running this heater for the first time after hook­ing up to gas supply. If so, the con­trol knob may need to be pressed in for 30 seconds or less. This will allo w air to bleed from the gas system.
6. With control knob pressed in, press and release ignitor button. This will light pilot. The pilot is attached to the front burner. If needed, keep press­ing ignitor button until pilot lights.
Note:
If pilot does not stay lit, con­tact a qualified service person or gas supplier for repairs. Until repair s are made, light pilot with match. T o light pilot with match, see Manual Light- ing Procedure on page 15.
7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.
• If control knob does not pop out
when released, contact a qualified service person or gas supplier for repairs.
Note:
If pilot goes out, repeat steps 3 through 7. This heater has a safety interlock system. W ait one (1) minute for system to reset before lighting pilot again.
Ignitor Electrode
Thermocouple
Figure 28 - Pilot
8. T urn contr ol knob counterclockwise to desired heating level. The
burners should light. Set control knob to any heat level between HI and LO.
Pilot Burner
Continued
14
103427
Page 15
SPLIT OAK AND AMERICAN OAK DESIGN
18", 24" AND 30" MODELS
OPERATING HEATER
Thermostat­Controlled Models
Continued
CAUTION: Do not try to adjust heating levels by using the manual shutoff valve.
TO TURN OFF GAS
TO APPLIANCE
Shutting Off Heater
1. T urn control knob clockwise to the OFF position.
Shutting Off Burners Only (pilot stays lit)
1. Tur n control knob clockwise to the PILOT position.
THERMOSTAT CONTROL
OPERATION
(Thermostat-Controlled
Models Only)
The thermostat control knob can be set to any comfort level between Hi and Lo. The thermostat will gradually modulate the heat output and flame height from higher to lower settings, or pilot, in order to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc.
Note:
Selecting the Hi setting with the control knob will cause the burner to remain fully on, without modulating down in most cases.
MANUAL LIGHTING
PROCEDURE
1. Follow steps 1 through 5 under Light-
ing Instructions, page 14.
2. Depress control knob and light pilot
with match.
3. Keep control knob pressed in for 30
seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 8, page 14.
OPERATING HEATER
Manually-Controlled Models
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING: If you do not fol­low these instructions exactly, a fire or explosion may result caus­ing property damage, personal injury or loss of life.
A. This appliance has a pilot which must
be lighted by hand. When lighting the pilot, follow these instructions ex­actly.
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your build­ing.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas sup­plier, call the fire department.
C. Use only your hand to push in or turn
the gas control knob. Ne ver use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part
has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been un­der water.
LIGHTING
INSTRUCTIONS
WARNING:
• If fireplace has glass doors, never operate this heater with glass doors closed. If you op­erate heater with doors closed, heat buildup inside fireplace will cause glass to burst. Also if fireplace opening has vents at the bottom, you must open the vents before operating heater.
• You must operate this heater with a fireplace screen in place. Make sure fireplace screen is closed before running heater.
NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orange flame will also be present. Open damper or window to vent smell. This will only last a few hours.
Note:
Homeowners generally prefer to
operate their heater with the chimney damper closed. This will put all the heat into the room. However there may be times you will desire the full flames of the High heat setting but will find the heat output excessive. You can open the chim­ney damper (if you have one) fully or partially to release some of the heat. WARNING: Damper handle will be hot if heater has been running.
1. STOP! Read the safety information above.
2. Make sure manual shutoff valve is fully open.
3. Press in and turn control knob clock­wise to the OFF position.
Ignitor Button
Figure 29 - Control Knob and Ignitor Button Location
Control Knob
Continued
103427
15
Page 16
UNVENTED PROPANE GAS LOG HEATER
OPERATING HEATER
Manually-Controlled Models
Continued
4. Wait f ive (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety in­formation above. If you don’t smell gas, go to the next step.
5. Press in control knob and turn coun­terclockwise to the PILOT position. Keep control knob pressed in for fiv e (5) seconds (see Figure 29).
Note:
You may be running this
heater for the first time after hook­ing up to gas supply. If so, the con­trol knob may need to be pressed in for 30 seconds. This will allow air to bleed from the gas system.
6. With control knob pressed in, press and release ignitor button. This will light pilot. The pilot is attached to the front burner. If needed, keep press­ing ignitor button until pilot lights.
Note:
If pilot does not light, contact a qualified service person or gas sup­plier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Light- ing Procedure, column 2.
7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.
• If control knob does not pop out
when released, contact a qualified service person or gas supplier for repairs.
Note:
If pilot goes out, repeat steps
3 through 7.
Thermocouple
Figure 30 - Pilot
8. Push in and turn control knob coun­terclockwise position. Both burners should light. Set control knob to desired setting.
Ignitor Electrode
Pilot Burner
C-clockwise
to the HIGH
VARIABLE CONTROL
OPERATION
The variable control valve can be set to any heat setting and flame height desired, by simply turning the control knob until that setting is attained. Even the lowest setting provides realistic flames and glow­ing embers from two burners. Selecting higher settings produces greater heat output. This results in increased heating comfort.
WARNING: Do not operate
heater between locked positions.
CAUTION: Do not try to adjust heating levels by using the manual shutoff valve.
TO TURN OFF GAS
TO APPLIANCE
Shutting Off Heater
1. Press in and turn control knob clock­wise
2. Turn the control knob clockwise
Clockwise
3. Press in control knob and turn clock­wise
to the HIGH position.
Clockwise
to the PILOT position.
to the OFF Position.
Clockwise
Shutting Off Burners Only (pilot stays lit)
1. Turn the control knob clockwise
to the HIGH position.
Clockwise
2. Press in and turn control knob clock­wise
to the pilot position.
Clockwise
MANUAL LIGHTING
PROCEDURE
1. Follow steps 1 through 5 under Light­ing Instructions, page 15.
2. Depress control knob and light pilot with match.
3. Keep control knob pressed in for 30 seconds after lighting pilot. After 30
seconds, release control knob. Now follow step 8, above.
INSPECTING BURNERS
Check pilot flame pattern and burner flame patterns often.
PILOT FLAME PATTERN
Figure 31 shows a correct pilot flame pat­tern. Figure 32 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the thermocouple. This will cause the thermocouple to cool. When the thermocouple cools, the heater will shut down.
Thermocouple
Figure 31 - Correct Pilot Flame Pattern
Thermocouple
Figure 32 - Incorrect Pilot Flame Pattern
If pilot flame pattern is incorrect, as shown in Figure 32
• turn heater off (see To Turn Off Gas to Appliance, page 15 [thermostat­controlled models] or page 16 [manually-controlled models])
• see Troubleshooting, pages 18 through 20
Pilot Burner
Pilot Burner
16
103427
Page 17
SPLIT OAK AND AMERICAN OAK DESIGN
18", 24" AND 30" MODELS
INSPECTING BURNERS
Continued
FRONT BURNER FLAME PATTERN
Figure 33 shows correct front burner flame pattern. Figure 34 shows incorrect front burner flame pattern. The incorrect burner flame pattern shows yellow tipping at top of blue flame.
WARNING: If yellow tipping occurs, your heater could pro­duce increased levels of carbon monoxide. If front burner flame pattern shows yellow tipping, fol­low instructions at bottom of this page. Yellow flame on rear burner is normal.
NOTICE: Do not mistake orange flames with yellow tipping. Dirt or other fine particles are burned by heater, causing brief patches of orange flame.
CLEANING AND MAINTENANCE
WARNING: Turn off heater
and let cool before cleaning.
CAUTION: You must keep control areas, burners, and cir­culating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a quali­fied service person. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, etc.
ODS/PILOT AND BURNERS
• Use a vacuum cleaner or small, soft bristled brush to clean.
LOGS
• If you remove logs for cleaning, re­fer to Installing Logs, page 12, to properly replace logs.
• Replace log(s) if broken or chipped (dime-sized or larger).
CORRECT FLAME PATTERN AT HIGH POSITION
Figure 33 - Correct Front Burner Flame Pattern
INCORRECT FLAME PATTERN AT HIGH POSITION
Figure 34 - Incorrect Front Burner Flame Pattern
If front burner flame pattern is incorrect, as shown in Figure 34
• turn heater off (see To Turn Off Gas to Appliance, page 15 [thermostat­controlled models] or page 16 [manually-controlled models])
• see Troubleshooting, pages 18 through 20
103427
Yellow Tipping At Top of Blue Flame
17
Page 18
UNVENTED PROPANE GAS LOG HEATER
TROUBLESHOOTING
Note: All troubleshooting items are listed in order of operation.
OBSERVED PROBLEM
When ignitor button is pressed, there is no spark at ODS/pilot
When ignitor button is pressed, there is spark at ODS/pilot but no ignition
WARNING: Turn off and un­plug heater and let cool before servicing. Only a qualified ser­vice person should service and repair heater.
POSSIBLE CAUSE
1. Ignitor electrode not connected to igni­tor cable
2. Ignitor cable pinched or wet
3. Piezo ignitor nut is loose
4. Broken ignitor cable
5. Bad piezo ignitor
6. Ignitor electrode positioned wrong
7. Ignitor electrode broken
1. Gas supply turned off or manual shutoff valve closed
2. Control knob not in PILOT position
3. Control knob not pressed in while in PI­LOT position
4. Air in gas lines when installed
5. Depleted gas supply
6. ODS/pilot is clogged
7. Gas regulator setting is not correct
CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot. This can damage ODS/ pilot unit.
REMEDY
1. Reconnect ignitor cable
2. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry
3. Tighten nut holding piezo ignitor to base panel of log set. Nut is located behind base panel.
4. Replace ignitor cable
5. Replace piezo ignitor
6. Replace ignitor
7. Replace ignitor
1. Turn on gas supply or open manual shutoff valve
2. Turn control knob to PILOT position
3. Press in control knob while in PILOT position
4. Continue holding down control knob. Repeat igniting operation until air is re­moved
5. Contact local propane gas company
6. Clean ODS/pilot (see Cleaning and Maintenance, page 17) or replace ODS/ pilot assembly
7. Replace gas regulator
ODS/pilot lights but flame goes out when control knob is released
1. Control knob not fully pressed in
2. Control knob not pressed in long enough
3. Safety interlock system has been trig­gered
4. Manual shutoff valve not fully open
5. Pilot flame not touching thermocouple, which allows thermocouple to cool, causing pilot flame to go out. This prob­lem could be caused by one or both of the following: A) Low gas pressure B) Dirty or partially clogged ODS/ pilot
6. Thermocouple connection loose at con­trol valve
7. Thermocouple damaged
8. Control valve damaged
18
1. Press in control knob fully
2. After ODS/pilot lights, keep control knob pressed in 30 seconds
3. W ait one minute for safety interlock sys­tem to reset. Repeat ignition operation
4. Fully open manual shut-off valve
5. A) Contact local propane gas company
B) Clean ODS/pilot (see Cleaning and Maintenance, page 17) or replace ODS/ pilot assembly
6. Hand tighten until snug, then tighten 1/4 turn more
7. Replace thermocouple
8. Replace control valve
Continued
103427
Page 19
SPLIT OAK AND AMERICAN OAK DESIGN
TROUBLESHOOTING
Continued
18", 24" AND 30" MODELS
OBSERVED PROBLEM
One or both burners do not light after ODS/ pilot is lit
Delayed ignition of one or both burners
Burner backfiring during combustion
Yellow flame in front burner during burner combustion
Slight smoke or odor during initial opera­tion
POSSIBLE CAUSE
1. Inlet gas pressure is too low
2. Burner orifice(s) clogged
3. Mislocated crossover tube
4. Burner orifice(s) diameter is too small
1. Manifold pressure is too low
2. Burner orifice(s) clogged
3. Mislocated crossover tube
1. Burner orifice is clogged or damaged
2. Damaged burner
3. Gas regulator defective
1. Not enough air
2. Gas regulator defective
1. Residues from manufacturing processes and logs curing
REMEDY
1. Contact local natural gas company
2. Clean burner(s) (see Cleaning and Main- tenance, page 17) or replace burner orifice(s)
3. Contact qualified service person
4. Replace burner orifice(s)
1. Contact local natural gas company
2. Clean burner(s) (see Cleaning and Main- tenance, page 17) or replace burner orifice(s)
3. Contact qualified service person
1. Clean burner (see Cleaning and Main- tenance, page 17) or replace burner ori­fice
2. Replace damaged burner
3. Replace gas regulator
1. Check burner(s) for dirt and debris. If found, clean burner(s) (see Cleaning and Maintenance, page 17)
2. Replace gas regulator
1. Problem will stop after a few hours of operation
Heater produces a whistling noise when burners are lit
Moisture/condensation noticed on windows
103427
1. Turning control knob to HI position when burners are cold
2. Air in gas line
3. Air passageways on heater blocked
4. Dirty or partially clogged burner orifice(s)
1. Not enough combustion/ventilation air
19
1. Turn control knob to LO position and let warm up for a minute
2. Operate burners until air is removed from line. Have gas line checked by lo­cal natural gas company
3. Observe minimum installation clear­ances (see pages 6-8)
4. Clean burners (see Cleaning and Main- tenance, page 17) or replace burner orifice(s)
1. Refer to Air for Combustion and Venti-
lation requirements (page 4)
Continued
Page 20
UNVENTED PROPANE GAS LOG HEATER
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
IMPORTANT:
supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors. These odors will disappear over time.
Operating heater where impurities in air exist may create odors. Cleaning
OBSERVED PROBLEM
Heater produces a clicking/ticking noise just after burners are lit or shut off
Heater produces unwanted odors
Heater shuts off in use (ODS operates)
Gas odor even when control knob is in OFF position
POSSIBLE CAUSE
1. Metal expanding while heating or con­tracting while cooling
1. Heater burning vapors from paint, hair spray, glues, cleaners, chemicals, new carpet, etc. (See ment above)
2. Low fuel supply
3. Gas leak. See Warning statement
at top of page
1. Not enough fresh air is available
2. Low line pressure
3. ODS/pilot is partially clogged
1. Gas leak. See Warning statement
at top of page
2. Control valve defective
IMPORTANT
state-
REMEDY
1. This is common with most heaters. If noise is excessive, contact qualified ser­vice person
1. Open window to ventilate room. Stop us­ing odor causing products while heater is running
2. Refill supply tank
3. Locate and correct all leaks (see Check- ing Gas Connections, page 11)
1. Open window and/or door for ventila­tion
2. Contact local propane gas company
3. Clean ODS/pilot (see Cleaning and Maintenance, page 17)
1. Locate and correct all leaks (see Check- ing Gas Connections, page 11)
2. Replace control valve
Gas odor during combustion
Log set cycles to pilot, but room tempera­ture drops to a lower than ideal level before log set comes back on
1. Foreign matter between control valve and burner
2. Gas leak. See Warning statement
at top of page
1. Thermostat sensing bulb needs to be repositioned
20
1. Take apart gas tubing and remove for­eign matter
2. Locate and correct all leaks (see Check- ing Gas Connections, page 11)
1. Reposition thermostat sensing bulb (see
Instructions for Optional Positioning of Thermostat Sensing Bulb, page 21)
103427
Page 21
SPLIT OAK AND AMERICAN OAK DESIGN
18", 24" AND 30" MODELS
OPTIONAL POSITIONING OF THERMOSTAT SENSING BULB
For Masonry and Factory­built Metal Fireplace
If your log set cycles to pilot, but the room temperature drops to a lower than ideal comfort level before the log set comes back on, you may want to reposition the thermostat sensing bulb.
The thermostat sensing bulb is located on the gas valve assembly. This location al­lows the thermostat to keep the room tem­perature at an ideal comfort level for most fireplace applications. For positioning the thermostat sensing bulb elsewhere, an adhe­sive-backed mounting clip has been pro­vided.
Tools needed: 5/16" hex driver or socket
1. Locate the gas valve assembly and ther­mostat sensing bulb (see Figure 35).
3. With 5/16" hex driver or socket, loosen the thermostat screw. Carefully slide the thermostat sensing bulb out of the retaining clamp (see Figure 37).
Note:
Do not remove the screw . Make sure you tighten the screw after remov­ing the thermostat sensing bulb.
IMPORTANT:
Do not force or bend the
thermostat sensing bulb or capillary.
Screw
Retaining Clamp
Figure 37 - Removing Thermostat Sensing Bulb
Thermostat Sensing Bulb
4. The thermostat sensing bulb may be located to the lower right front side of fireplace. Determine location of sens­ing bulb, but do not mount sensing bulb until step 5. If you have a masonry fire­place, see Figure 38 for location.
If your fireplace has glass doors, position sensing bulb directly behind door gap on right bottom side (see Figure 40).
Thermostat Sensing Bulb
Adhesive­backed Mounting Clip
Capillary
Glass Doors
Figure 40 - Installing Thermostat Sensing Bulb behind Glass Doors
5. The mounting clip must be a minimum of 3" from bottom of fireplace to pre­vent crimping of capillary. Once you have decided on a location, clean the area thoroughly. Remove the paper backing from the adhesive on back of mounting clip. Press the clip into the new location so that the thermostat sensing bulb will be positioned verti­cally with the capillary at the bottom (see Figure 41). Slide the thermostat sensing bulb into the clip.
IMPORTANT:
Do not crimp capillary .
Gas Valve Assembly
Thermostat Sensing Bulb
Figure 35 - Location of Gas Valve Assembly and Thermostat Sensing Bulb
2. The adhesive-backed mounting clip (see Figure 36) is attached to the ther­mostat sensing bulb. Remove the ad­hesive-backed mounting clip.
Figure 36 - Adhesive-backed Mounting Clip
103427
Thermostat Sensing Bulb
Adhesive­backed Mounting Clip
Figure 38 - Locating Thermostat Sensing Bulb on Masonry Fireplace
If you have a factory-built metal fireplace, see Figure 39 for location.
Thermostat Sensing Bulb
Adhesive­backed Mounting Clip
Figure 39 - Locating Thermostat Sensing Bulb on Factory-built Metal Fireplace
21
Thermostat Sensing Bulb
Adhesive­backed
Capillary
Figure 41 - Positioning the Thermostat Sensing Bulb in the Vertical Position with the Capillary at the Bottom
Mounting Clip
Do Not Crimp Capillary
Page 22
UNVENTED PROPANE GAS LOG HEATER
SPECIFICATIONS
18" Thermostat- 24" Thermostat- 30" Thermostat­Controlled Controlled Controlled
Btu (Variable) 16,000/26,000 20,000/33,000 21,500/36,000 Type Gas Propane Only Propane Only Propane Only Ignition Piezo Piezo Piezo Manifold Pressure 7.9" W.C. 7.9" W.C. 7.9" W.C. Inlet Gas
Pressure (in. of water)
Maximum 14" 14" 14" Minimum* 11" 11" 11"
* For purpose of input adjustment Shipping Weight 26 lbs. 30 lbs. 34 lbs.
18" Variable 24" Variable 30" Variable Manually- Manually- Manually­Controlled Controlled Controlled
Btu (Variable) 16,000/26,000 20,000/33,000 21,500/36,000 Type Gas Propane Only Propane Only Propane Only Ignition Piezo Piezo Piezo Manifold Pressure 7.9" W.C. 7.9" W.C. 7.9" W.C. Inlet Gas
Pressure (in. of water)
Maximum 14" 14" 14" Minimum* 11" 11" 11"
* For purpose of input adjustment Shipping Weight 26 lbs. 30 lbs. 34 lbs.
REPLACEMENT PARTS
Note:
Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty.
Parts Under Warranty
Contact authorized dealers of this product. If they can’t supply original replacement part(s), call DESA International’s Techni­cal Service Department at 1-800-323-5190.
When calling DESA International, have ready
• your name
• your address
• model number of your heater
• how heater was malfunctioning
• type of gas used (propane or natural gas)
• purchase date Usually, we will ask you to return the defec-
tive part to the factory.
Parts Not Under Warranty
Contact authorized dealers of this product. If they can’t supply original replacement part(s), call DESA International’s Parts Department at 1-800-972-7879 for referral information.
When calling DESA International, have ready
• model number of your heater
• the replacement part number
SERVICE HINTS
When gas pressure is too low
• pilot will not stay lit
• burners will have delayed ignition
• heater will not produce specified heat
• propane/LP gas supply may be low
When gas quality is bad
• pilot will not stay lit
• burners will produce flames and soot
• heater will backfire when lit You may feel your gas pressure is too low or
gas quality is bad. If so, contact your local propane/LP gas supplier.
TECHNICAL SERVICE
You may have further questions about in­stallation, operation, or troubleshooting.
If so, contact DESA International’s Techni­cal Service Department at
1-800-DESA LOG (1-800-337-2564).
22
103427
Page 23
SPLIT OAK AND AMERICAN OAK DESIGN
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
18", 24" AND 30" MODELS
ACCESSORIES
Purchase these heater accessories from your local dealer. If they can not supply these accessories, call DESA International’s Parts Department at 1-800-972-7879 for referral information. You can also write to the ad­dress listed on the back page of this manual.
MANUAL SHUTOFF VALVE - GA5010
For all models. Manual shutoff valve with 1/ 8" NPT tap. Fits 1/2" NPT pipe.
BLACK FIREPLACE HOOD - GA6050
For all models. Helps deflect heat away from mantel or wall above fireplace.
VENT-FREE LOGMATE™ STOVE
- SVFBC
For models VL18N/P, VL18NT(A), VL18PT(A), VL18NV, VL18PV, VS18NV(B), VS18PV(B), VS18NT(A), VS18PT(A), CF18N/P, CF18NT(A), CF18PT(A), CFS18NV(B), CFS18PV(B).
VENT-FREE LOGMATE FIRE­BOXES
Available in 32", 36", and 42" models. May be paired with the logs listed below. Circulating fireboxes feature louvers and an optional blower. Non-circulating, smooth face models are ideal for custom trim appli­cations such as stone or marble.
FB36CA, FB42C SERIES (CIR­CULATING), FB36NCA, FB42NC SERIES (NON-CIRCULATING)
For all 18" and 24" models listed above plus the following 30" models: VL30N/P, VL30NT(A), VL30PT(A), VL30NV, VL30PV, VS30NV(A, B), VS30PV(A,B), VS30NT(A), VS30PT(A), CF30N/P, CF30NT(A), CF30PT(A), CS30NV(A, B), CS30PV(A, B).
DAMPER CLAMP - GA6080
For manually controlled models. Perma­nently opens chimney flue damper for vented operation.
LAVA ROCK - GA6060
For all models. Order when additional rock is desired. (3 lb. bag)
BRASS FIREPLACE HOOD - GA6052
For all models. Helps deflect heat away from mantel or wall above fireplace.
103427
FB32C (CIRCULATING), FB32NC (NON-CIRCULATING) SERIES
For 18" and 24" models: VL18N/P, VL24N/P, VL18NT(A), VL18PT(A), VL24NT(A), VL24PT(A), VL18NV, VL18PV, VL24NV, VL24PV, VS18NV(B), VS18PV(B), VS24NV(A, B), VS24PV(A, B), VS18NT(A), VS18PT(A), VS24NT(A), VS24PT(A), CF18N/P, CF24N/P, CF18NT(A), CF18PT(A), CF24NT(A),CF24PT(A), CS18NV(B), CS18PV(B), CS24NV(A,B), CS24PV(A, B).
23
Page 24
UNVENTED PROPANE GAS LOG HEATER
ILLUSTRATED PARTS BREAKDOWN
Variable Manually­Controlled Models
VS18PVB CFS18PVB VS24PVB CFS24PVB VS30PVB CFS30PVB
1L
1R
4
25
7-2
7-1
7
5
3
2
27
27-1
27-2
21
28
10
6
12
29
17
8
18
29
23
22
24
21
25
26
19
20
9
11
13
16
15
14
24
103427
Page 25
SPLIT OAK AND AMERICAN OAK DESIGN
18", 24" AND 30" MODELS
PARTS LIST
Variable Manually-Controlled Models
KEY PART NUMBER FOR NO. VS18PVB/CFS18PVB VS24PVB/CFS24PVB VS30PVB/CFS30PVB DESCRIPTION QTY.
1L 103580-01 103580-03 Left Front Log (#1L) 1 1R 103580-04 103580-02 103580-02 Right Front Log (#1R) 1 2 103576-01 103576-02 103576-03 Bottom Middle Log (#2) 1 3 103577-02 103577-01 103577-03 Rear Log (#3) 1 4 103578-02 103578-01 103578-03 Top Middle Log (#4) 1 5 103579-02 103579-01 103579-01 Crossover Log (#5) 1 6 101006-01 101006-01 101006-01 Pilot Bracket 1 7 101330-04 101330-05 101330-06 Front Burner Assembly 1 7-1 101008-01 101008-01 101008-01 Crossover Burner Gasket 1 7-2 101007-01 101007-01 101007-01 Crossover Burner 1 8 100999-01 100999-02 100999-03 Rear Burner Assembly 1 9 101331-10 101331-08 101331-09 Base Assembly (Includes Decals) 1 10 098271-07 098271-06 098271-06 Ignitor Cable 1 11 102445-01 102445-01 102445-01 Piezo Ignitor 1 12 098867-10 098867-10 098867-10 Gas Regulator 1 13 M11084-38 M11084-38 M11084-38 Screw 2 14 101011-01 101011-02 101011-03 Inlet Tube 1 15 098354-01 098354-01 098354-01 Control Knob 1 16 098462-03 098462-03 098462-03 Control Rod 1 17 098325-01 098325-01 098325-01 Roll Pin 1 18 098508-01 098508-01 098508-01 Valve Retainer Nut 1 19 102568-02 102568-02 102568-02 Gas Valve 1 20 101005-01 101005-01 101005-01 Valve Bracket 1 21 M11084-26 M11084-26 M11084-26 Screw 4 22 101004-10 101004-01 101004-02 Rear Burner Injector 1 23 101004-10 101004-02 101004-06 Front Burner Injector 24 102258-01 102258-01 102258-01 Burner Tube 1 25 099387-08 099387-08 099387-08 Pilot Tube 1 26 098276-01 098276-01 098276-01 1/8” Plug 1 27 099059-02 099059-02 099059-02 O.D.S. Pilot 1 27-1 098594-01 098594-01 098594-01 Ignitor Electrode 1 27-2 098593-01 098593-01 098593-01 Thermocouple 1 28 098249-01 098249-01 098249-01 Nut 4
This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 22 of this manual.
103427
PARTS AVAILABLE — NOT SHOWN
100563-01 100563-01 100563-01 Warning Plate 1 101055-02 101055-02 101055-02 Lighting Instructions Plate 1 100565-01 100565-01 100565-01 Warning Plate Fastener 1 100639-01 100639-01 100639-01 Caution Decal 1 101137-01 101137-01 101137-01 Hardware Kit 1 101416-27 101416-27 101416-27 Information Video 1 GA6060 GA6060 GA6060 Lava Rock 1
25
Page 26
UNVENTED PROPANE GAS LOG HEATER
ILLUSTRATED PARTS BREAKDOWN
Thermostat- Controlled Models
VS18PTA VS24PTA VS30PTA
1L
1R
10
4
10-2
8
29
10-1
5
3
2
7
7-1
7-2
6
8
13
9
15
12
17
14
13
16
18
19
11
20
31
8
27
26
24
21
30
6
25
29
23 22
28
26
103427
Page 27
SPLIT OAK AND AMERICAN OAK DESIGN
18", 24" AND 30" MODELS
PARTS LIST
Thermostat-Controlled Split Oak Models
KEY PART NUMBER FOR NO. VS18PTA VS24PTA VS30PTA DESCRIPTION QTY.
1L —— 103580-01 103580-03 Left Front Log (#1L) 1 1R 103580-04 103580-02 103580-02 Right Front Log (#1R) 1 2 103576-01 103576-02 103576-03 Bottom Middle Log (#2) 1 3 103577-02 103577-01 103577-03 Rear Log (#3) 1 4 103578-02 103578-01 103578-03 Top Middle Log (#4) 1 5 103579-02 103579-01 103579-01 Crossover Log (#5) 1 6 M11084-26 M11084-26 M11084-26 Screw 5 7 099059-02 099059-02 099059-02 O.D.S. Pilot 1 7-1 098594-01 098594-01 098594-01 Ignitor 1 7-2 098593-01 098593-01 098593-01 Thermocouple 1 8 098249-01 098249-01 098249-01 Nut 4 9 101006-01 101006-01 101006-01 Pilot Bracket 1 10 101330-04 101330-05 101330-06 Front Burner Assembly 1 10-1 101008-01 101008-01 101008-01 Gasket, Crossover Burner 1 10-2 101007-01 101007-01 101007-01 Crossover Burner 1 11 100999-01 100999-02 100999-03 Rear Burner Assembly 1 12 101331-05 101331-06 101331-07 Base Assembly (with decals) 1 13 098271-07 098271-06 098271-06 Ignitor Cable 1 14 102445-01 102445-01 102445-01 Piezo Ignitor 1 15 098867-10 098867-10 098867-10 Gas Regulator 1 16 M11084-38 M11084-38 M11084-38 Screw 2 17 102810-01 102810-01 102810-01 Inlet Tube 1 18 098354-01 098354-01 098354-01 Control Knob 1 19 098462-03 098462-03 098462-03 Control Rod 1 20 100000-01 100000-01 100000-01 Cotter Pin 1 21 101053-01 101053-01 101053-01 Adapter 1 22 099211-01 099211-01 099211-01 Screw 1 23 098544-01 098544-01 098544-01 Thermostat Clamp 1 24 101329-15 101329-18 101329-17 Thermostat Gas Valve Assy. 1 25 100994-01 100994-01 100994-01 Thermovalve Bracket 1 26 101004-10 101004-01 101004-02 Rear Burner Injector 1 27 101004-10 101004-02 101004-06 Front Burner Injector 1 28 102811-01 102811-01 102811-01 Thermostat Burner Tube 1 29 099387-09 099387-09 099387-09 Pilot Tube 1 30 102255-01 102255-01 102255-01 Strap 1 31 102764-01 102764-01 102764-01 Heat Shield 1
This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 22 of this manual.
103427
PARTS AVAILABLE — NOT SHOWN
100563-01 100563-01 100563-01 Warning Plate 1 101054-01 101054-01 101054-01 Lighting Instructions Plate 1 100565-01 100565-01 100565-01 Warning Plate Fastener 1 100639-01 100639-01 100639-01 Caution Decal 1 101137-01 101137-01 101137-01 Hardware Kit 1 101416-27 101416-27 101416-27 Information Video 1 GA6060 GA6060 GA6060 Lava Rock 1
27
Page 28
UNVENTED PROPANE GAS LOG HEATER
ILLUSTRATED PARTS BREAKDOWN
Variable Manually-Controlled Models
VL18PV VL24PV VL30PV
2
4
3
1
5
7-2
7-1
7
29
9
11
8
25
29
27
27-1
27-2
21
28
10
6
23
22
12
14
13
28
15
16
17
18
24
21
25
26
19
20
103427
Page 29
SPLIT OAK AND AMERICAN OAK DESIGN
18", 24" AND 30" MODELS
PARTS LIST
Variable Manually-Controlled American Oak Models
KEY PART NUMBER FOR NO. VL18PV VL24PV VL30PV DESCRIPTION QTY.
1 101337-01 101337-02 101337-03 Rear Log (#1) 1 2 101336-01 101336-02 101336-03 Front Log (#2) 1 3 101334-01 101335-01 101335-02 Crossover Log (#3) 1 4 101333-02 —— —— Front Branch - 18" (#4) 1
—— 101332-01 101332-02 Left Front Branch (#4) 1 5 —— 101333-01 101333-01 Right Front Branch (#5) 1 6 101006-01 101006-01 101006-01 Pilot Bracket 1 7 101330-04 101330-05 101330-06 Front Burner Assembly 1 7-1 101008-01 101008-01 101008-01 Crossover Burner Gasket 1 7-2 101007-01 101007-01 101007-01 Crossover Burner 1 8 100999-01 100999-02 100999-03 Rear Burner Assembly 1 9 101331-10 101331-08 101331-09 Base Assembly (Includes Decals) 1 10 098271-07 098271-06 098271-06 Ignitor Cable 1 11 102445-01 102445-01 102445-01 Piezo Ignitor 1 12 098867-10 098867-10 098867-10 Gas Regulator 1 13 M11084-38 M11084-38 M11084-38 Screw 2 14 101011-01 101011-02 101011-03 Inlet Tube 1 15 098354-01 098354-01 098354-01 Control Knob 1 16 098462-03 098462-03 098462-03 Control Rod 1 17 098325-01 098325-01 098325-01 Roll Pin 1 18 098508-01 098508-01 098508-01 Valve Retainer Nut 1 19 102568-02 102568-02 102568-02 Gas Valve 1 20 101005-01 101005-01 101005-01 Valve Bracket 1 21 M11084-26 M11084-26 M11084-26 Screw 4 22 101004-10 101004-01 101004-02 Rear Burner Injector 1 23 101004-10 101004-02 101004-06 Front Burner Injector 24 102258-01 102258-01 102258-01 Burner Tube 1 25 099387-08 099387-08 099387-08 Pilot Tube 1 26 098276-01 098276-01 098276-01 1/8” Plug 1 27 099059-02 099059-02 099059-02 O.D.S. Pilot 1 27-1 098594-01 098594-01 098594-01 Ignitor Electrode 1 27-2 098593-01 098593-01 098593-01 Thermocouple 1 28 098249-01 098249-01 098249-01 Nut 4
This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 22 of this manual.
103427
PARTS AVAILABLE — NOT SHOWN
100563-01 100563-01 100563-01 Warning Plate 1
101055-02 101055-02 101055-02 Lighting Instructions Plate 1
100565-01 100565-01 100565-01 Warning Plate Fastener 1
100639-01 100639-01 100639-01 Caution Decal 1
101137-01 101137-01 101137-01 Hardware Kit 1
101416-27 101416-27 101416-27 Information Video 1
GA6060 GA6060 GA6060 Lava Rock 1
29
Page 30
UNVENTED PROPANE GAS LOG HEATER
NOTES
_______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________
30
103427
Page 31
SPLIT OAK AND AMERICAN OAK DESIGN
18", 24" AND 30" MODELS
NOTES
_______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________
103427
31
Page 32
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model Serial No. Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied.
LIMITED WARRANTY
VENT-FREE PROPANE GAS LOG HEATERS
DESA International warrants this product to be free from defects in materials and components for three (3) years and five (5) years on stainless steel burners from the date of first purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under this warranty the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater to proper operating condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s) MUST be obtained through authorized dealers of this product and/or DESA International who will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty. The heater MUST be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MER­CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO THREE (3) YEARS ON ALL COMPONENTS AND FIVE (5) YEARS ON STAINLESS STEEL BURNERS FROM THE DATE OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDI­RECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. For information about this warranty write:
2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004
103427 01
NOT A UPC
103427-01 Rev. C 09/97
Loading...