Desa E36L, E36LB, E36LH, E36LBH, E32LB User Manual
...
ELECTRIC FIREPLACE
OWNER’S OPERATION AND INSTALLATION MANUAL
MODELS E32L, E32LB, E32LH, E32LBH,
E36L, E36LB, E36LH AND E36LBH
PLEASE READ THIS MANUAL BEFORE INSTALLING
AND USING APPLIANCE.
WARNING: If the information in this manual is not followed exactly, an electrical shock or re may result causing property damage, personal injury or loss of life.
FOR YOUR SAFETY
— Do not store or use gasoline or other ammable va-
pors and liquids in the vicinity of this or any other
appliance.
— Installation and service must be performed by a quali-
ed service agency.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
For more information, visit www.desatech.com
TABLE OF CONTENTS
Safety .................................................................. 2
Product Specication ........................................... 3
Installation ........................................................... 3
Features and Operation....................................... 7
Accessory Installation .......................................... 8
Troubleshooting ................................................. 14
Wiring Diagram .................................................. 15
SAFETY
WARNING: Electrical wiring
must comply with local building codes and other applicable
regulations to reduce the risk of
re, electrical shock and injury
to persons.
WARNING: Do not use this
replace if any part of it has
been under water. Immediately
call a qualied service technician to inspect the replace and
replace any part of the electrical
system.
CAUTION: Extreme caution
is necessary when any heater is
used by or near children or invalids and whenever the heater is
left operating and unattended.
1. Read all instructions before using this
replace.
2. This replace is hot when in use. To avoid
burns, do not let bare skin touch hot surfaces. If provided, use handles when accessing replace controls. Keep combustible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at
least 3 feet from front of replace.
3. Extreme caution is necessary when any
heater is used by or near children or invalids and whenever heater is left operating
and unattended.
4. Always place main power switch in OFF
position when not in use.
5. Do not operate replace if any part has
been damaged or is malfunctioning.
Maintenance ...................................................... 16
Technical Service............................................... 23
Replacement Parts ............................................ 23
Parts .................................................................. 24
Accessories ....................................................... 27
Warranty .............................................. Back Cover
6. Any repairs to this replace should be
done by a qualied service person.
7. Do not use outdoors.
8. This replace is approved for installation
in bedrooms.
9. Under no circumstances should this
replace be modied. Parts having to be
removed for servicing must be replaced
prior to operating this replace.
10. This replace is not intended for use in
bathrooms, laundry areas and similar
locations where it would be subject to
excessive moisture.
11. This replace may not be installed outdoors or in an unenclosed space where
exposed to the elements.
12. To disconnect this replace, turn off at
circuit breaker or fuse panel.
13. Th is appliance , must be elec trically
grounded in accordance with local codes
and the National Electric Code, ANSI/
NFPA No. 70 or in Canada with CSA
C22.1 Canadian Electrical code.
14. Do not insert or allow foreign objects to
enter any ventilation or exhaust openings.
This may cause an electrical shock, re
or damage to replace.
15. To prevent a possible re do not block air
intakes or exhaust.
16. This firepl ace has hot and arcin g or
sparking parts inside. Do not use in areas
where gasoline, paint or ammable liquids
are used or stored. This replace should
not be used to dry clothing or for hanging
decorations.
17. Use this replace only as described. Any
other use not recommended by the manufacturer may cause re, electric shock or
injury to persons.
18. SAVE THESE INSTRUCTIONS.
www.desatech.com
111076-01F2
E32 = 155/8"
E36 = 17"
E32 = 161/4"
E36 = 175/8"
E32 = 221/4"
E36 = 241/4"
E32 = 293/8"
E36 = 35"
E32 = 7"
E36 = 8"
E32 = 61/2"
E36 = 51/4"
E32 = 18
3
/
8
"
E36 = 21"
E32 = 33
3
/
8
"
E36 = 37"
E32 = 363/8"
E36 = 43"
E32 = 353/8"
E36 = 42"
E32 = 345/8"
E36 = 411/4"
E32 = 32
5
/
8
"
E36 = 36
1
/
4
"
E32 = 28
3
/
8
"
E36 = 31
3
/
4
"
E32 = 32
7
/
8
"
E36 = 36
1
/
2
"
17/8"
5/8"
TOP
FRONT
LEFT SIDE RIGHT SIDE
E32 = 32
1
/
8
"
E36 = 36
1
/
8
"
E32 = 28
3
/
8
"
E36 = 31
3
/
4
"
To Nail
Location
To Nail
Location
E32 = 8"
E36 = 51/4"
ELECTRICAL SPECIFICATIONS
Voltage: 120 VAC, 60 Hz
Total Amps: 12.5 Amps
Total Watts: 1500 Watts
Heater Rating: 1100 Watts
Max. Bulb Rating: 100 Watts
Use only on 15 amp circuit
Internal Wall
Installation
Full Projection
Installation
Flush
Installation
Corner
Installation
PRODUCT SPECIFICATION
Figure 1 - Unit Dimensions
INSTALLATION
LOCATING FIREPLACE
Plan where to locate and frame replace.
Before installation consider the following:
1. Fireplace location must allow for wall and
2. Fireplace screen should not be exposed
3. A 15 amp, 120 Volt, 60 Hz circuit with
Flush Installations are recommended where
living space is limited or at a premium. Since
space required to enclose replace would
be located beyond an outside wall, this installation would require additional planning
and construction. Check local codes for any
restrictions.
ceiling clearances (see Installation Clear-
ances, page 4).
to direct sunlight from windows or doors.
proper ground must be available. A dedicated circuit should be provided to avoid
circuit breaker trips or blown fuses.
Projected Installations can extend any distance into room. A projection may be ideal for
a new addition on an existing, nished wall.
Corner Installations make use of space
that may not normally be used and provides
a wider and more efcient viewing angle and
heat distribution.
Internal Wall Installations provide a discrete
option for room separation and can also be an
ideal addition to an existing wall.
Figure 2 - Possible Installation Locations
111076-01F 3
www.desatech.com
Facing Material May
Be Noncombustible
Wall Treatments or
Combustible Wood
Combustible Wood
Mantels and Trims
May Extend Above
Profile Shown when
Maintained within
30° Parameter
Shown
Framed
Material
Top of Cabinet
Note: All Mantel Clearances
are Measured from Top of
Fireplace Opening
30°
16 5/8"
Ref.
9 5/8" Ref.
12" Ref.
13 3/4"
4 1/2"
1 1/2"
1 3/4"
10 1/2" Min.
10 1/2"
Top View of Fireplace
Safe Zone
5"
3"
30°
1 3/4" Max.
Minimum 10" from
Perpendicular Side Wall
Edge of Firebox
Opening
Combustible
MaterialMust
Not Overlap
Front Face
INSTALLATION
Continued
INSTALLATION CLEARANCES
Minimum clearances to combustible construction are:
• Top, Back and Sides of Recessed
Cabinet . . . . . . . . . . . . . . . . . . . . .0" Min.
• Drywall to Sides of Front Face . . .0" Min.
• Framing at Nailing Flanges . . . . . .0" Min.
• Ceiling to Opening . . . . . . . . . . . .36" Min.
Mantel Clearances
For mantel clearances see Figures 3 and 4.
• Floor . . . . . . . . . . . . . . . . . . . . . . .0" Min.
• Front . . . . . . . . . . . . . . . . . . . . . .36" Min.
• Perpendicular Side Wall . . . . . . .10" Min.
Figure 3 - Mantel Clearances
Figure 4 - Mantel Side Clearances
www.desatech.com
111076-01F4
BUILT-IN INSTALLATION
VE32 = 34 5/8"
VE36 = 41 1/4"
VE32 = 15 7/8"
VE36 = 17 1/4"
VE32 = 32 5/8"
VE36 = 36 1/4"
Platform/Subflooring
VE32 = 37 5/8"
VE36 = 42 3/8"
VE32 = 26 5/8"
VE36 = 29 3/8"
VE32 = 52 3/4"
VE36 = 58 1/4"
11 5/8"
These Dimensions
Allow for 11 5/8" of
Clearance to Side
Wall of Fireplace
and 10' Clearance
to Perpendicular
Side Walls
Built-in installations require a framed enclosure constructed of 2" x 4" or heavier lumber
and sized in accordance with Figure 5. This
allows unit to slide into opening and be nailed
to stud at sides and top nailing anges. These
anges accept 5/8" drywall or plywood board
to nish unit ush to face. Optional trim accessories are available that will extend 1/2"
over rough edge of wall opening (see Acces-
sories, page 25).
IMPORTANT: If installing a perimeter trim kit,
you must install shoulder screws before inserting replace into opening. See instructions
included with trim kit. If installing a mantel,
you must follow clearance instructions (see
Installation Clearances, page 4).
A hearth extension is suggested for a more
pleasing appearance. The replace may be
raised on a wood or non-combustible platform
supporting its entire width and depth and
extending in front of the replace as long as
louvers are not obstructed.
Note: When installing replace in cold climates against a non-insulated exterior wall,
wall must be fully insulated in accordance with
local building code.
Figure 5 - Framing Dimensions
INSTALLATION
Continued
Figure 6 - Corner Dimensions
ELECTRICAL INSTALLATION
WARNING: Any electrical re-
wiring of this appliance must be
done by a qualied electrician.
This wiring must be done in ac-
cordance with local codes and/or
in the U.S.A. with the current, Na-
tional Electrical Code ANSI/NFPA
No 70 and in Canada with CSA
C22.1 Canadian Electric code.
This replace should be connected to a dedicated 15 Amp,
circuit as other appliances may
cause the circuit breaker to trip
or fuse to blow when replace
is in operation.
A junction box with universal strain adaptor is
provided to hard wire unit to a 15 amp, 120
Volt 60 Hz grounded circuit. If necessary,
junction box may be relocated to route supply to left side.
1. Remove 2 screws and outer cover on right
side (see Figure 7, page 6).
2. Remove inner screw securing junction
box.
3. Slide junction box up until mounting tab
is lined up to notch in outer cabinet.
4. Swing box out and slip retaining ange
out through slot in outer cabinet.
5. Remove 2 screws and outer cover on left
side and reattach on right side of outer
cabinet.
111076-01F 5
www.desatech.com
INSTALLATION
Continued
6. Swing junction box with harness to left
side while pulling sufcient length of harness out through control panel cover to
reach mounting location on left side.
7. Reinsert retaining ange through slot and
swing screw mounting tab back through
notch as before.
8. Slide junction box down until mounting
holes line up and replace inner retaining
cover.
9. Pull end of 3 wire Romex supply line
through universal strain relief bushing in
remaining cover.
10. Strip back outer Romex to about 4” and
connect black, white and green wires accordingly using approved connectors.
Junction Box
Screws
and
Outer
Cover
11. Tuck tailing wires into junction box and
replace cover using 2 remaining screws.
12. Tighten down strain adjustment on universal bushing until Romex sheathing is
secured.
IMPORTANT: Inspect components and wiring for damage before connecting power to
unit. If any components are found damaged,
contact an authorized dealer for original DESA
Heating Products replacement part(s) or call
DESA Heating Products at 1-866-872-6040
for referral.
IMPORTANT: Prior to operation remove foam
shipping brace located under motor mount
(see Figure 8).
Motor
Mount
Slot
Retaining
Notch
Screws and
Outer Cover
from Other Side
Figure 7 - Relocating Junction Box to
Flange
Mounting
Tab
Junction Box
Cover with
Universal
Strain Relief
Left
www.desatech.com
Foam
Shipping
Brace
Figure 8 - Removing Shipping Brace
111076-01F6
INSTALLATION
Continued
LAMPS AND LAVA ROCK
Before operating replace, lamp bulbs must
be inspected and lava rock may be added if
desired.
1. Lift log bed off hearth base to gain access
to lamp xtures (log bed is attached with
contact magnets).
2. Turn on power to light circuit and check
that all bulbs are operating. Bulb placement front left to right are red, yellow and
orange (see Figure 9).
Note: If bulbs need replacing, see Replacing Light Bulbs, page 16. Be careful not to
tear or damage reective strips. If they have
come loose, ends can be easily reattached or
replaced at support brackets. See Replacing
Reective Ribbons, page 21.
FEATURES AND OPERATION
This electronic fir eplace series features
a random ame effect, and a realistic log
bed with glistening embers that can be adjusted for ame speed and light intensity.
E36/32LH models have a circulating heater,
rated at 1100 Watts. Models E36/32LB and
E36/32LBH include a hand detailed, textured,
red-brick lining.
Access controls by pulling two handle tabs
of upper louver until panel releases from
magnetic catches and swings down to open
position (see Figure 10).
Figure 11, page 8, shows control layout for
heater equipped models with main power
switch to ame controls and heater power
switch (when equipped) to heating unit. This
allows independent and efcient operation of
both features.
Once main power is turned on, ame speed
and brightness may be turned on and adjusted
independently.
3. Center log bed over opening between
viewing panel screen and grate.
4. Cover remaining hearth area with 1/4" of
lava rock (provided), if desired.
Viewing Panel
Screen
Red
Yellow
Orange
Grate
Log Bed
Figure 9 - Bulb Placement
Figure 10 - Accessing Controls
111076-01F 7
www.desatech.com
LOWLOW
MAIN
POWER
HI- OFF
FLAME SPEED
HI- OFF
FLAME BRIGHTNESS
HEATER
ON/OFF
Switch
FEATURES AND OPERATION
Continued
Flame Speed
Heater Switch
Flame Brightness
Figure 11 - Control Panel
ACCESSORY INSTALLATION
OPTIONAL GLASS DOORS
Models E36L and E32L will accept bifold glass
doors that are fully operable or a xed panel
door that limits access to replace, (see Ac-
cessories, page 25).
Installing Bifold Glass Doors
Follow these steps to install left and right
operable panels:
1. With handle down, completely fold panel
on its hinges.
2. With handle facing center of rebox opening insert lower pivot pin on door panel
into hole in bottom outer edge of rebox
opening (see Figure 12).
3. Keep folded door tilted and slide upper two
pins into guide track below upper facial
edge of rebox opening.
4. Tilt glass assembly fully vertical until outer
pivot pin snaps into mounting hole in upper spring clip.
5. Once top and bottom pins are secured,
unfold door into closed position.
6. Repeat steps 1 through 5 for opposite
door assembly.
7. To adjust doors, slide partially open.
Using a Phillips screwdriver, loosen holddown screws on spring clips (see Figure
13).
8. Close both doors until evenly joined at
middle and note gap as measured to outer
edges of front face.
9. Reopen each door one at a time and
retighten the hold-down screw while preserving noted gap at each edge.
10. Repeat process until both doors are evenly joined, spaced and working freely.
Spring Clip
Depress Spring
Clip to Release
Pivot Pin
Fold Bifold Door
After Releasing
Spring Clip to
Slide Door Out of
Upper Track
Remove Pivot Pin
From Bottom Face
While Sliding Door
Out of Upper Track
Pivot Pin
Figure 12 - Installing/Removing Glass
Doors
Side Front
Face
Spring Clip
Partially
Opened
Door
Figure 13 - Adjust Glass Door
www.desatech.com
111076-01F8
ACCESSORY INSTALLATION
Continued
Removing Bifold Glass Doors
Bifold doors may be removed for replacing
or cleaning.
1. Partially open each door and press up on
upper spring clip with a screw driver until
outer top pivot pin is free of the clip.
2. Fully fold frame assembly and slide upper
edge towards center of rebox opening
until the guide pins are free of the frame
rail (see Figure 12, page 8).
Installing Series Fixed Glass Doors
1. Hold glass door rmly at both handles and
insert top pins into clips located below upper facial edge of rebox opening. Make
sure top pins snap securely into holes on
spring clips (see Figure 14).
2. Push up on glass against tension of spring
clips. Swing lower door into face until lower
pins clear bottom rail and set into locating
holes on each end (see Figure 14).
Note: If pins do not align into spring clips,
slightly loosen retaining screws on each clip
(see Figure 13, page 8). Reinsert panel into
each spring clip and align panel into lower
locating holes. Remove panel, nish tighten
screws and reinsert panel.
Spring Clip
OPTIONAL BRICK LINERS
Installing or Removing Brick Liner Kits
Brick liner kits are availab le for Models
E36/32(L)(H) (see Accessories, page 25).
These brick panels may be installed anytime
after replace installation is complete.
Follow these steps to install left and right
brick panels:
1. Remove glass doors (if equipped). Follow
instructions under Optional Glass Doors,
page 8.
2. Remove each retaining screw holding
screen rods and pull entire screen and rod
assembly out of locating hole on inside top
edge of rebox (see Figure 15).
3. Remove log bed from hearth pan and
place in a safe area. Log bed is attached
with contact magnets only.
4. Remove two screws holding each refractory bracket to rebox. Pull up and lift out
of positioning slot at bottom of hearth pan
(see Figure 16, page 10).
Note: E36L and E36LH models require
removal of additional hearth brackets and
face panels which are held in place by 2
screws on hearth pan and one screw at top
retainer bracket (see Figure 16, page 10).
Mounting
Holes
Locating
Hole
Figure 14 - Installing Fixed Glass Doors
111076-01F 9
www.desatech.com
Screen
Rod
Retaining
Screw
Figure 15 - Removing Screen/Rod
Assembly
Loading...