Denon DVD-910 User Manual

DVD VIDEO PLAYER

DVD-910

OPERATING INSTRUCTIONS MODE D’EMPLOI INSTRUCCIONES DE OPERACION

WARNING

: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

PRECAUTIONS

Laser Safety

This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECI-

CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO

LOCATION: INSIDE, NEAR THE DECK MECHANISM.

FIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

BEAM.

FCC WARNING-This equipment may generate or use radio frequency energy. Changes or modifications to

this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

RADIO-TV INTERFERENCE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and receiver.

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA

FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

Nonuse periods - Turn the unit off when it is not in use. Unplug the unit from the household AC outlet if it is not to be used for a long time. Unplug the unit during lightning storms.

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.

¡Keep the set away from moisture water and dust. ¡Never disassemble or modify the set in any way. ¡Do not put heavy objects on the AC power cord. ¡Keep the AC power cord away from heat appliances. ¡Once the AC power cord is damaged be sure to replace with a new one.

–2–

Important Safeguards

1) Read Instructions - All the safety and operating instructions should be read before the product is operated.

2) Retain Instructions - The safety and operating instructions should be retained for future reference.

3) Heed Warnings - All warnings on the product and in the operating instructions should be adhered to.

4) Follow Instructions - All operating and use instructions should be followed.

5) Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6) Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7) Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8) Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9) A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10) Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.

11) Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12) Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

PORTABLE CART WARNING

(Symbol provided by RETAC)

S3125A

13) Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14) Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning and power-line surges.

15) Power lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16) Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

17) Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

18) Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19) Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into

the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by follow-

ing the operating instructions. Adjust only those

controls that are covered by the operating instruc-

tions as an improper adjustment of other controls

may result in damage and will often require exten-

sive work by a qualified technician to restore the

product to its normal operation, e) If the product has been dropped or damaged in

any way. f) When the product exhibits a distinct change in per-

formance - this indicates a need for service.

20) Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

21) Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

22) Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

English

–3–

■

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Laser Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . 3

■

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

About Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Symbols Used in this Manual. . . . . . . . . . . . . . . . . . . . . 5

■

ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Playable Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Disc Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

■

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

■

FUNCTIONAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . 8

FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . 8

Tour of the remote control . . . . . . . . . . . . . . . . . . . . . . . 9

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Displays During Operation . . . . . . . . . . . . . . . . . . . . . . 11

Loading the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . 11

■

HOOK UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Description - rear panel . . . . . . . . . . . . . . . . . . . . . . . . 12

Connection to an audio system . . . . . . . . . . . . . . . . . . 13

Connection to a TV (for video) . . . . . . . . . . . . . . . . . . . 14

■

PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Basic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

General Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Brightness of the Front Display . . . . . . . . . . . . . . . . . . 15

Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Disc Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

CALLING UP A MENU SCREEN DURING

PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Step by Step Playback. . . . . . . . . . . . . . . . . . . . . . . . . 15

Resume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Fast Forward / Reverse Search . . . . . . . . . . . . . . . . . . 16

Slow Forward / Slow Reverse . . . . . . . . . . . . . . . . . . . 16

Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Title / Chapter Search . . . . . . . . . . . . . . . . . . . . . . . . . 17

Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

REPEAT TITLE / CHAPTER. . . . . . . . . . . . . . . . . . . 17

REPEAT TRACK . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Program (CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Random Playback (CD) . . . . . . . . . . . . . . . . . . . . . . . . 18

MP3 / JPEG / WMA Playback . . . . . . . . . . . . . . . . . . . 19

Slide Show Mode (JPEG) . . . . . . . . . . . . . . . . . . . . . . 20

On-Screen Information. . . . . . . . . . . . . . . . . . . . . . . . . 20

Track Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Random Playback (MP3 / JPEG / WMA) . . . . . . . . . . . 20

Program (MP3 / JPEG / WMA). . . . . . . . . . . . . . . . . . . 21

Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Stereo Sound Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Subtitle Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Changing the On-Screen Display . . . . . . . . . . . . . . . . . 22

Marker Setup Screen. . . . . . . . . . . . . . . . . . . . . . . . . . 23

Black Level Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Virtual Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

■

DVD SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Display Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Audio Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Ratings Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

RATING LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

IF YOU FORGET THE PASSWORD . . . . . . . . . . . . . 25

CONTROL LEVELS . . . . . . . . . . . . . . . . . . . . . . . . . 25

■

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

■

TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . 28

■

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

–4–

INTRODUCTION

+10

SEARCH MODE

OPEN / CLOSE

ZOOM

DISPLAY

AUDIO

TOP MENU

SETUP

PLAY

SKIP

A-B REPEAT

REPEAT

CLEAR

SUBTITLE

MODE

ANGLE

RETURN

STOP

VIRTUALPOWER

STILL / PAUSE

ENTER

The serial number of this product may be found on the back of the DVD player. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

About Copyright

Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Apparatus Claimas of U. S. Patent Nos, 4,631,603, 4,577,216, 4,819,098, and 4,907,093 licensed for limited viewing uses only.

Supplied Accessories

Please check to make sure the following items are included with the main unit in the carton.

Remote control

• • • • • • • •

“AA” (R6P)

batteries

• • • • • •

Audio cable

• • • • • • • • •

Video cable

• • • • • • • • •

Operating Instruction

• • • •

Service Station

• • • • • • • • • • •

List

English

(approx. 3 feet

(100 cm) long)

(approx. 3 feet

(100 cm) long)

Symbols Used in this Manual

The following symbols appear below in some headings and notes in this manual, with the following meanings!

: Description refers to playback of DVD video discs.

: Description refers to playback of audio CDs.

: Description refers to playback of discs formatted with MP3.

: Description refers to viewing of JPEG discs.

: Description refers to playback of discs formatted with WMA.

: Description refers to the items to be set in the QUICK mode.

–5–

DVD-V

QUICK

MP3

JPEG

WMA

ABOUT THE DISCS

Example

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2Chapter 3 Chapter 4

Example

Track 1 Track 2 Track 3 Track 4 Track 5 Track 6

Example

Group 1 Group 2

Track 1 Track 2 Track 1 Track 2Track 3 Track 4

DVD video

(NOTE 1)

DVD-R

DVD-RW

(NOTE 2)

CD-R

CD-RW

(NOTE 3)

Picture CD

Digital video

(MPEG2)

Digital audio

MP3

WMA

(NOTE 4)

Digital picture

(JPEG)

JPEG

Mark (logo)

Usable

discs

Recorded

signals

Disc Size

12 cm

8 cm

NOTE 1: Some DVD video discs do not operate as described in

this manual due to the intentions of the discs’ producers.

NOTE 2: Playing DVD-R and DVD-RW discs

DVD-R and DVD-RW discs on a DVD recorder can be played. Discs that have not be finalized cannot be played. Depending on the disc’s recording status, the disc may not be accepted or may not be played normally (the picture or sound may be not be smooth, etc.).

NOTE 3: Some of CD-R/CD-RW discs may be incompartible

because of “scratch and stain of disc”, “Recording condition”, and “Characteristic of Recorder”.

NOTE 4: Windows Media and the Windows logo are

trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.

Playable Discs

The following discs can be played back on this DVD player.

Disc Types

[

DVD-Video

Data on a DVD is divided into sections called "titles," and then into subsections called "chapters," each of which is given a title or chapter number. Playback conditions are preset on some DVD video discs, and these playback conditions take priority over user operations on this player. If a function you selected does not run as desired, refer to the manual accompanying the disc.

[

AUDIO CD

Data on an audio CD is divided into sections called “tracks,” each of which is given a track number.

[

MP3, JPEG, WMA

Data on a MP3 is divided into sections called "groups," and then into subsections called "tracks," each of which is given an album or track number.

]

This player conforms to the NTSC color system. You cannot play discs recorded in other color systems such as PAL or SECAM.

¡Some discs include region codes as shown below.

¡The number inside the symbol refers to a region of

the world, and a disc encoded in a specific region format can only be played back on DVD players with the same region code.

The following discs cannot be played back on this DVD player.

¡DVD with region codes other than 1 or ALL. ¡DVD-ROM ¡DVD-RAM (Never play back, otherwise malfunc-

tion may result.)

¡CD-ROM ¡Video CD ¡VSD ¡CDV (Only plays back the audio part.) ¡CD-G (Only plays back the sound.) ¡CD-R/CD-RW (Only plays back the discs which

audio CD/MP3/JPEG/WMA is recorded.)

¡CD-I (Never play back, otherwise malfunction may

result.)

¡SACD ¡Photo CD (Never play back, otherwise malfunc-

tion may result.)

Any other discs without compatibility indications.

CAUTION:

Use caution not to pinch your finger in the disc slot.

¡Be sure to remove a disc and unplug the AC power cord

from the outlet before carrying the DVD player.

–6–

FEATURES

¡Progressive Scan system

Unlike conventional interlace scanning, the progressive scan system provides less flickering and images in higher resolution than that of traditional television signals.

¡Dolby Digital sound

This player can handle Dolby Digital surround sound having 5.1 channels when connected to a Dolby Digital decoder.

¡Still/fast/slow/step playback

Various playback modes are available including still pictures, fast forward/reverse, slow motion and step frames.

¡Random playback for audio CD, MP3, JPEG, and

WMA

This player can shuffle the order of tracks to play them in random order.

¡Program playback for audio CD, MP3, JPEG, and

WMA

You can program the order of tracks to play them in any desired order.

¡DVD menus in a desired language

You can display DVD menus in a desired language, if available on a DVD.

¡Auto standby

When the screen saver program is activated for 35 minutes, the power is automatically turned off.

¡Subtitles in a desired language

You can select a desired language for the display subtitles, if that language is available on a disc.

¡Selecting a camera angle

You can select the desired camera angle, if a disc contains sequences recorded from different angles.

¡Choices for audio language and sound mode

You can select the desired audio language and sound mode, if different languages and modes are available on a disc.

¡Parental lock

You can set the control level to limit playback of discs which may not be suitable for children.

¡Automatic detection of discs

This player automatically detects if a loaded disc is DVD, audio CD, MP3, JPEG, or WMA.

¡Playing an MP3 disc

You can enjoy MP3 files which are recorded on CDR/RW.

¡Direct Search

You can search the desired title, chapter, and track with numeric button during playback or in stop mode.

¡On-screen display

Information about the current operation can be displayed on a TV screen, allowing you to confirm the currently active functions (such as program playback), on the TV screen using the remote control.

¡DTS (Digital Theater System)

When you connected DTS decorder, you can enjoy

5.1channel surround system developed by the Digital Theater System co. which reproduces the original sound as truthfully as possible.

¡Search

Chapter search:Search for the chapter designated by

Title search: Search for the title designated by user

Track search: Search for the track designated by

Time search: Search for the time designated by

¡Repeat

Chapter: Repeated playback of the chapter of

Title: Repeated playback of the title of the

Track: Repeated playback of the track of the

Disc

(audio CD)

(MP3/JPEG/WMA)

A-B: The part between A and B designated

Group: Repeated playback of the folder of the

¡Zoom

2-time and 4-time magnified screen can be displayed.

¡Marker

The part designated by user can be called back.

¡Resume Play

User can resume to playback from the part at which the play was stopped even if the power turn off.

¡Component Video Out Jacks

Jacks located on the back of the DVD Player which are used to send high-quality video to a TV via Component Video In Jacks.

¡Dimmer

Brightness of the display can be varied.

¡Bit rate indication ¡DRC (Dynamic range control)

You can control the range of sound volume.

¡Playing a disc in Video Recording Format

The product can run a disc recorded in the Video Recording Format.

¡Displaying a JPEG picture (NOTES 1)

Kodak Picture CDs can be played. Still images stored in JPEG format on CD-R/RW can also be played.

¡Reproducing WMA data (NOTES 2)

You can enjoy WMA files which are recorded on CD-R/RW.

“Kodak Picture CD COMPATIBLE” is trademark of Eastman Kodak Company.

“WMA” (Windows Media Audio) is a new audio codec developed by Microsoft® in the United States of America.

user is possible.

is possible.

user is possible.

the disc being played is possible.

disc being played is possible.

disc being played is possible. : Repeated playback is possible. : Repeated playback is possible.

by user is possible.

MP3/JPEG/WMA disc being played is

possible.

English

–7–

16 17

18 19

31 3

27 26

25 5

11 4

1 2

61578

1214

FUNCTIONAL OVERVIEW

FRONT PANEL

REMOTE CONTROL

1. ON/STANDBY, (POWER ON/OFF) Buttons [page 15]

2. Disc loading tray

3. OPEN/CLOSE Button [page 15]

4. PLAY Button [page 15]

5. STILL/PAUSE Button [page 15]

6. STOP Button [page 15]

7. Cursor Buttons [page 15]

Use when making settings while watching the display on a TV screen.

MENU Button [page 15]

9. SETUP Button [page 24]

10. ENTER Button [page 15]

11. G (SKIP UP/FWD) Button [page 17]

Plays back from the beginning of the next chapter or track. Hold down to fast forward playback.

12. H (SKIP DOWN/REV) Button [page 17]

Plays back from the beginning of the current chapter or track. Hold down to fast reverse playback.

13. VIRTUAL Button [page 23]

14. DIMMER Button [page 15]

15. Display, Remote Sensor Window

16. A-B REPEAT Button [page 18]

17. REPEAT Button [page 17]

18. RANDOM Button [page 20]

19. ZOOM Button[page 16]

20. CLEAR Button [page 17]

21. ANGLE Button [page 22]

Press to change the camera angle to see the sequence being played back from a different angle.

22. RETURN Button [page 21]

23. SEARCH MODE Button [page 17]

24. h (FR SEARCH) Button[page 16]

25. g (FF SEARCH) Button [page 16]

26. SUBTITLE Button [page 22]

Press to select a desired subtitle language.

27. TOP MENU Button [page 15]

28. DISPLAY Button [page 20]

29. AUDIO Button [page 21]

Press to select a desired audio language or sound mode.

30. Numeric Buttons [page 17]

31. MODE Button [page 20]

The buttons with circled numbers can only be operated with the remote control.

–8–

POWER

A-B REPEAT Button

REPEAT Button

MODE Button

SUBTITLE Button

DVD CD

• Press this to switch the power between on and standby.

•

Marks a segment to repeat between A and B.

• Marks a segment to repeat between A and B.

•

Allows you to repeat play a Title or Chapter.

• Allows you to repeat play a Track or Disc.

RANDOM Button

• Allows you to shuffle the playing order of tracks.

ZOOM Button

• To set black level on/off.

• To activate the 3D sound (Virtual

surround system).

• Allows you to program a specific order or random playback.

•

To activate the 3D sound (virtual surround system).

• To magnify part of picture (x2/x4).

ANGLE Button

•

Accesses various camera angles on a disc.

• Accesses various subtitles on a disc.

AUDIO Button

DISPLAY Button

•

Accesses various audio functions on a disc.

• To select STEREO, L-CH or R-CH.

• Displays the current disc mode. • Displays the current disc mode.

• To search chapter, title, or time.

• To rapidly return to a location of disc.

OPEN/CLOSE Button

• To search track or time.

• To rapidly return to a location of disc.

SEARCH MODE Button

NUMERIC Buttons

CLEAR Button

• To open or close the disc tray. • To open or close the disc tray.

• To select chapter directly. • To select track directly.

• Clear the makers.

• Removes status No. in program input.

FUNCTIONAL OVERVIEW

Tour of the remote control

Buttons on remote control work in different ways for DVD and CD : Refer to the following table for correct use.

English

–9–

FUNCTIONAL OVERVIEW

MENU Button

TOP MENU Button

ENTER, CURSOR Buttons

RETURN Button

SEARCH Buttons

DVD CD

• Brings up the Menu on a disc.

• Brings up the Top Menu on a disc.

•

Moves the cursor and determines its position.

SETUP Button

• Returns to a previous menu.

• Brings up the DVD player's Setup menu.

SKIP Buttons

• To skip Chapters.

• Allows you to search forward/backward

through a disc (x2. x8. x50. x100).

STOP Button

PLAY Button

• To stop playback.

• Begin disc play.

STILL/PAUSE Button

• Moves the cursor and determines its position.

• Brings up the DVD player's Setup menu.

• To skip Tracks.

• Allows you to search forward/backward through a

disc (x16).

• To stop playback.

• Advances playback one frame at a time.

• Pause disc play.

• Begin disc play.

Tour of the remote control

–10–

FUNCTIONAL OVERVIEW

Stays on when the inserted disc is being played back.

Lights up when a CD is inserted into the tray.

Lights up when a DVD is inserted into the tray.

Lights up when the inserted disc comes to a pause.

Stays on when repeat chapter function is on.

Stays on when repeat track function is on.

Stays on when the A-B repeat function is on.

Stays on when the repeat function is on.

Stays on when repeat title function is on.

Displays how long a current title or track has been played back. When a chapter or track has switched, the number of a new title, chapter or track is displayed.

Power on

No disc inserted

Tray open

Tray closed

Loading the Disc

Power off

Display

English

Displays During Operation

Loading the Batteries

1. Open the battery compartment cover.

2. Insert two “AA” (R6P) batteries, with each one oriented correctly.

3. Close the cover.

NOTES

• Do not mix alkaline and manganese batteries.

• Do not mix old and new batteries.

Cautions On Batteries

• Use “AA” (R6P) batteries in this remote control unit.

• Replace the batteries with new ones approximately once a year, though this depends on the frequency with which the remote control unit is used.

• If the remote control unit does not operate from close to the main unit, replace the batteries with new ones, even if less then a year has passed.

• The included battery is only for verifying operation. Replace it with a new battery as soon as possible.

• When inserting the batteries, be careful to do so in the proper direction, following the and marks

in the remote control unit’s battery compartment.

• To prevent damage or battery fluid leakage:

• Do not use a new battery with an old one.

• Do not use two different types of batteries.

• Do not short-circuit, disassemble, heat or dispose of batteries in flames.

• Remove the batteries when not planning to use the remote control unit for a long period of time.

• If the batteries should leak, carefully wipe off the fluid from the inside of the battery compartment, then insert new batteries.

–11–

HOOK UPS

2345

Description - rear panel

1. DIGITAL OUT JACKS:

Use either an optical or coaxial digital cable to connect to a compatible Dolby Digital receiver. Use to connect to a Dolby Digital decoder or DTS decoder.

2. AUDIO OUT JACKS

Connect to the Audio input jacks of A/V-compatible TV or wide screen TV, Stereo system.

3. VIDEO OUT JACK

Use a video cable to connect one of the jack to Video input on your A/V-compatible TV or wide screen TV, Stereo system.

4. COMPONENT VIDEO OUT JACKS

Use these jacks if you have a TV with Component Video in jacks. These jacks provide CR, CBand Y video. Along with SVideo, Component Video provides the best picture quality.

5. S-VIDEO OUT JACK

Use the S-Video cable to connect this jack to the S-Video jack on your A/V-compatible TV or wide screen TV for a higher quality picture.

6. PROGRESSIVE switch

Selecting Progressive Scan (480p or Interlaced 480i) Playback

¡If your TV is compatible with progressive scanning (480p), connect the TV to the Component Video Output jacks of the DVD

player and set the Progressive switch on the back of the DVD player to “PROGRESSIVE”. Next, set your TV to the progressive scan mode.

If your TV is not compatible with progressive scan, keep the Progressive switch to “INTERLACE”.

¡Use a commercially available adaptor if the video input jacks of your TVs or monitors are the BNC type.

What is Progressive Scanning?

¡Unlike conventional interlace scanning, the progressive scan system provides less flickering and images in higher resolution

than that of traditional (480i) television signals.

NOTE

¡When the Progressive switch is set to “PROGRESSIVE,” no video signal will be output from VIDEO OUT or S-VIDEO OUT

jack.

The DCDi (Directional Correlational De-interlacing) system of this DVD player produces smooth and natural video images, even if really dynamic, by eliminating the jagged edges. *“DCDi”is a registered trademark of Faroudja, a division of Genesis Microchip Inc.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

–12–

HOOK UPS

The following show examples of connections commonly used to connect the DVD player either TV and other components.

Notes

¡Be sure to turn off the power to all components in the system before connecting another component. ¡Refer to the Instruction Manuals for your TV, stereo system and any other components to be connected to the

DVD player.

Connection to an audio system

Method 1 Method 2

Stereo system

AUDIO

DVD

Audio Input Jacks

Analog Audio Out

Digital Audio Input Jacks

Digital Audio Out

English

Dolby Digital decoder

DTS decoder

• Method 1 DVD Player + Stereo system

• Method 2 DVD Player + Dolby Digital decoder or DTS decoder

NOTES

• If output Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to on for audio output in the setup mode. (See page 25)

• If output DTS audio, connect to a DTS decoder, and set DTS to ON for audio output in the setup mode. (See page 25)

•

Unless connected to a Dolby Digital decoder, or a DTS decoder, set Dolby Digital or DTS to off for audio output in the setup

mode. Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers. (See page 25)

• The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital sound by an MD or DAT deck. Set Dolby Digital and DTS to OFF for audio output in the setup mode for method 1 only. Playing a DVD using incorrect settings

• may generate noise distortion, and may also damage the speakers. (Refer to page 25 to set ON for Dolby Digital and DTS)

Optical cable (not supplied)

• Optical cable (not supplied) may be damaged when bent at sharp angles. Ensure cables are coiled in loops with a diameter of 15 cm or more when storing them.

• Use a cable which is 3m or shorter.

• Insert cable plugs firmly into the connectors when making connections.

• If a plug has minor scratches or is dirty, clean it with a soft cloth before inserting it into a connector.

–13–

HOOK UPS

Connection to a TV (for video)

Method 1 Method 2 Method 3

Good pictureBasic Audio Better picture

VIDEO IN

AV Cable S-Video

DVD

Analog Audio out Video out

• Method 1 DVD Player + TV with Video Input Jack

• Method 2 DVD Player + TV with S-Video Input Jack

• Method 3 DVD Player + TV with Component Video Jacks

S-VIDEO IN

Cable

S-Video out

Best picture

COMPONENT

S-VIDEO IN

PBYPR

Video Cable

Component Video out

CBYCR

NOTES

• If your TV is compatible with progressive scanning (480p), connect the TV to the Component Video Output jacks of the DVD

player. Refer to page 12.

• Connect the DVD player directly to a TV. If the A/V cables are connected to a VCR, pictures may be distorted due to the

copy protection system.

• S-Video output connector

The video signals are divided into color (C) and brightness (Y) signals, achieving a clearer picture. If the TV is equipped with a S-Video input connector, we recommend connecting it to the this product’s S-Video output connector using a commercially available S-Video connection cord.

HOW TO CONNECT TO A TV WITHOUT AUDIO/VIDEO INPUT JACKS

If your TV does not have RCA type audio and video input jacks it is still possible to connect this DVD player to your TV’s 75-ohm coaxial antenna terminal using an optional Stereo Audio/Video RF Modulator, not included. Connect the audio and video outputs of the DVD player to the audio and video inputs on the RF Modulator, and then connect the coaxial output of the RF Modulator (usually marked “TO TV”) to the 75 ohm coaxial antenna terminal on your TV. Follow the instruction supplied with the RF Modulator for more details. If your TV’s 75 ohm coaxial antenna terminal is already occupied by an antenna or cable box connection, remove that cable from your TV’s antenna terminal and reconnect it to the coaxial antenna input terminal of the RF Modulator (usually marked “ANT IN”), then connect the RF modulator to your TV’s antenna terminal as described above.

NOTE

• The picture quality from DVD discs will not be as good if the DVD player is connected to the TV’s antenna terminal

through an RF Modulator.

–14–

PLAYING A DISC

Basic Playback

CDDVD-V

Getting started

• Turn on the power of the TV, amplifier and any other components which are connected to the DVD.

• Make sure the TV and audio receiver (commercially available) are set to the correct channel.

Press the POWER ON button.

• “P-ON” will appear briefly on the display panel.

Press the OPEN/CLOSE button to open disc loading tray.

Place the disc in the tray, with the label facing up.

Press the PLAY button.

• The tray will close automatically, and playback will then start from the first chapter or track of the disc. If the playback does not start automatically, press the PLAY button.

• When you playback the DVD with a title menu is recorded, it may appear on the screen. In this case, refer to “TITLE MENU”.

Press the STOP button to stop playback.

NOTES:

• A “prohibited icon” may appear at the top-right on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD player or the disc.

• With DVDs that use some titles for playback program signals, playback may start from the second title, or it may skip these titles.

• During the playback of two layered disc, pictures may stop for a moment. This happens when the 1st layer switches to the 2nd layer. This is not a malfunction.

• During the playback of a DVD-RW which has been recorded in the VR mode, the sound or picture may freeze momentarily depended on disc content.

General Features

DVD may contain menus to navigate the disc and access special features. Press the appropriate numerical key or use the cursor buttons ( L / K / B / s ) to highlight your selection in the DVD main menu and press the ENTER button to confirm.

NOTE:

• Unless stated, all operations described are based on remote control use. Some operations can be carried out using the menu bar on the TV screen.

Pause

WMAMP3CDDVD-V

During playback, press the STILL/PAUSE button.

• Playback will pause and sound will be muted.

To continue playback, press the PLAY button.

Disc Menus

DVD-V

Press the MENU button.

• The DVD main menu will appear.

If the feature is not available, symbol may appear on the TV screen.

If disc menu is available on the disc, audio language, subtitle options, chapters for the title and other options will appear for selection.

Press the cursor buttons ( L / K / B / s ) to select an item, and the ENTER button to confirm selection.

Title Menu

DVD-V

Press the TOP MENU button.

• The title menu will appear.

If the feature is not available, symbol may appear on the TV screen.

Press the cursor buttons ( L / K / B / s ) to select an item, and the ENTER button to confirm selection.

• Playback will begin at the selected Title.

CALLING UP A MENU SCREEN DURING PLAYBACK

DVD-V

• Press the MENU button to call up the DVD main menu.

• Press the TOP MENU button to call up the title menu.

NOTE:

• Contents of menus and corresponding menu operations may vary between discs. Refer to the manual accompanying the disc for details.

English

Brightness of the Front Display

Press the DIMMER button on the front panel to select the desired brightness of the front display. (Bright, Dim, or OFF)

• “Bright” has been selected as the factory default.

NOTE:

• The brightness of the front display can be adjusted from the SETUP menu. Details are on page 24.

–15–

Step by Step Playback

DVD-V

During playback, press the STILL/PAUSE button.

• Playback will pause and sound will be muted.

The disc advances by one frame each time the

STILL/PAUSE button is pressed.

To exit step by step playback, press the PLAY but- ton.

PLAYING A DISC

Resume

During playback, press the STOP button.

• Resume message will appear on the TV screen.

Press the PLAY button, playback will resume from

Resume ON

Press 'PLAY' to play from here. To play the beginning, press 'STOP' first and then 'PLAY'.

the point at which playback was stopped.

• To cancel resume, press the STOP button twice.

NOTE:

• The resume playback takes a little longer to take place compared to the normal playback.

Fast Forward / Reverse Search

During playback, press the ggor hhbutton repeatedly to select the required forward or reverse speed: x2, x8, x50, x100.

• If you are using the SKIPGGbutton / the on the front panel, press and hold it for more than 1.5 sec (the longer you hold it, the faster the speed will be). When you reach the desired speed, release the button.

• For audio CDs, the speed is fixed at x16.

• For MP3 and WMA the speed is fixed at x8.

Button

To return to normal playback, press the PLAY but-

ton.

CDDVD-V

WMAMP3CDDVD-V

button

100

Zoom

DVD-V

The Zoom function allows you to enlarge the video image and to pan through the enlarged image.

Press the ZOOM button during playback.

• Playback will continue.

Press the ZOOM button repeatedly to select the required zoom factor: x2, x4 or OFF.

[x2] [x4]

Use the cursor buttons ( L / K / B / s ) to move the zoomed picture across the screen.

To exit zoom mode, press the ZOOM button to OFF.

NOTES:

• Zooming function does not work while disc menu is shown.

• x4 zoom is not available on some discs.

Slow Forward / Slow Reverse

DVD-V

During playback, press the

STILL/PAUSE button.

Press the ggor hhbutton.

•

Slow motion playback will begin and sound will be muted.

Press the ggor hhbutton repeatedly to select the required speed: 1/16, 1/8, 1/2 of the normal playback.

• If you are using the SKIP H button / the front panel, press and hold it for more than 1.5 sec (the longer you hold it, the slower the speed will be)

button on the

. When you reach the desired speed, release the button.

To return to normal playback, press the PLAY button.

Button

1/16

1/8

1/2

–16–

PLAYING A DISC

Track

WMAMP3CD

There are three ways to begin playback on an Audio CD, MP3 and WMA at a specific Track.

By using the Numeric buttons

Press the numeric buttons to enter the desired Track number.

• Playback will start at the selected track.

• For single digit tracks (1-9), press a single number (eg. track 3, press 3).

To play track 26, press +10, 2, 6 on the numerical button.

•

By using the SEARCH MODE button (Audio CD)

Press the SEARCH MODE button.

• The track search display appears.

Within 30 seconds, select a desired track number using the numeric buttons. For single digits press “0” first.

• Playback will start at the selected track.

SKIP

HH GG

button to move to the next

By using the SKIP buttons

During playback, press the track. Press it repeatedly to skip subsequent tracks. Press the

SKIP

Press it repeatedly to go to the previous tracks

button to go back to the beginning of the current track.

Track number will appear briefly on the DVD display panel.

•

• If any SKIP button is pressed while the playback is paused, the playback will be paused again after skipping to the next track.

NOTE:

• The

SKIP HGbuttons are not available when play-

back is stopped.

__/ 15

Time Search

CDDVD-V

During playback, press the

SEARCH MODE button three times (CD: twice) to

display the Time Search on the TV screen.

Within 30 seconds, enter a

desired disc time with the

_:__:__ 1:23:45

numeric buttons.

• Playback will start at the specified time.

Press the CLEAR button to erase the incorrect

input.

Repeat

• The REPEAT button is available only during playback.

REPEAT TITLE / CHAPTER

DVD-V

To activate the repeat function, press the REPEAT button during playback.

• The repeat mode changes as described below every time you press the button.

CHAPTER TITLEOFF

(repeat off)

NOTES:

• Repeat Title/Chapter is not available with some scenes.

• The REPEAT setting will be cleared when moving to other title or chapter.

(current chapter repeat) (current title repeat)

REPEAT TRACK

English

Title / Chapter Search

DVD-V

By using the SEARCH MODE buttons

Press the SEARCH MODE button once for the Chapter search, twice for the Title search during playback.

Enter the desired chapter/title number with the

numeric buttons.

SKIP

HH GG

button to move to the next

By using the SKIP buttons

During playback, press the chapter. Press it repeatedly to skip subsequent chapters. Press the chapter. Press it repeatedly to go to the previous chapter

SKIP

button to go back to the beginning of the current

–17–

To activate the repeat function, press the REPEAT button during playback.

• The repeat mode changes as described below every time you press the button.

TRACK ALLOFF

(repeat off)

(current track repeat) (entire disc repeat)

NOTES:

•

The REPEAT setting will be cleared when moving to other track Repeat playback does not function during A-B repeat playback.

•

WMAJPEGMP3

GROUP

(current folder

repeat)

(entire disc

repeat)

(repeat off)

TRACK ALLOFF

(current track

repeat)

PLAYING A DISC

A-B REPEAT

CDDVD-V

Press the A-B REPEAT button at your chosen starting point.

• A- appears briefly on the TV

screen.

Press the A-B REPEAT button again at your chosen end point.

• A-B appears briefly on the TV

screen, and the repeat sequence begins.

To exit the sequence, press the

A-B REPEAT button.

NOTES:

• The A-B repeat section can only be set within the current title (for DVDs), or current track (for audio CDs).

• A-B Repeat is not available with some scenes in DVD.

•

To cancel the A point which was set, press the CLEAR button.

• A-B Repeat playback does not function during title, chapter, track or all repeat playback.

A -

A - B

OFF

Program

You may determine the order in which tracks will play.

In stop mode press the MODE button.

• The PROGRAM screen will appear.

Press the cursor buttons (▲ or ▼) to select a track, then press the ENTER button.

• Press the CLEAR button to erase the most recently entered program.

Press the PLAY button to play the programmed tracks.

NOTES:

While the program is being played back, the STOP button works as

• follows.

•

Press the STOP button once and then the PLAY button again, playback will restart from the point where the STOP button was pressed. (Program continued)

•

Press the STOP button twice and then the PLAY button again, playback will restart from the track in the usual way. (Program cleared)

• Up to 99 programs can be entered.

• If you wish to repeat the current track in the program, press the REPEAT button repeatedly until TRACK appears during playback. If you wish to repeat the entire program press the REPEAT button repeatedly until ALL appears during playback.

• Refer to page 21 for program playback of MP3, WMA, and JPEG.

PROGRAM

CD [AUDIO] TOTAL 0:03:30

1 3:30

1 3:30 2 4:30 3 5:00 4 3:10 5 5:10 6 1:30 7 2:30

1/2 1/1

1 3:30

Random Playback

This shuffles the playing order of tracks instead of playback in the original sequence.

In stop mode, press the RANDOM or MODE button twice.

•

RANDOM screen appears

Press the PLAY button to start random playback.

NOTES:

• If you wish to repeat the current track in the random selection, press the REPEAT button repeatedly until TRACK appears during playback. If you wish to repeat the entire random selection press the REPEAT button repeatedly until ALL appears during playback.

• Refer to page 20 for random playback of MP3, WMA, and JPEG.

RANDOM

CD [AUDIO] TOTAL 0:45:55

RANDOM PROGRAM

--no indication--

–18–

PLAYING A DISC

MP3 / JPEG / WMA Playback

WMAJPEGMP3

This DVD player can reproduce images and sounds from data recorded in MP3, JPEG and WMA formats on CD-ROM, CD-R and CD-RW discs. The DVD player can also run JPEG files stored on Kodak picture CD. The user can enjoy picture images on the television set by reproducing picture CDs. * Picture CD is a service to convert a photograph taken by

conventional film camera into digital data and write the data

on a CD. For details of Picture CD, contact a shop that deals with developing service of Kodak Inc.

Information on MP3, JPEG and WMA discs

• A file with an extension of “.mp3 (MP3)” is called an “MP3 file”.

• A file with an extension of “.jpg (JPG)” or “.jpeg (JPEG)” is

called a “JPEG file”. The DVD player can run an image file conforming to the Exif* specification.

* This is a file format, Exchangeable Image File format

established by Japanese Electronic Industry Development Association (JEIDA).

• A file with an extension of “.wma (WMA)” is called a

“WMA file”.

• Files whose extension is other than “.mp3 (MP3)”, “.jpg

(JPG)”, “.jpeg (JPEG)” and “.wma (WMA)” will not be listed in the MP3, JPEG, or WMA menu.

• If the file is not recorded in MP3, JPEG or WMA format, noise

may be produced even if the file extension is either of “.mp3 (MP3)”, “.jpg (JPG)”, “.jpeg (JPEG)” and “.wma (WMA)”.

When a disc with MP3,JPEG or WMA files is inserted in the DVD player, the track menu will appear on the TV screen, and number of tracks is displayed on the front panel.

Place the disc in the tray with the label facing up.

For discs on which MP3, JPEG or WMA tracks are recorded:

• An MP3, JPEG or WMA track menu screen appears.

• A symbol of “ ” is shown on the top of the group name.

• A symbol of “ ” is shown on the top of MP3 files.

• A symbol of “ ” is shown on the top of JPEG files.

• A symbol of “ ” is shown on the top of WMA files.

• If the picture extends beyond the scope of screen, a down

arrow “L” appears, indicating that the user can view another part of the picture on the next page. If an up arrow “K” appears, it indicates that the user can view another part on the previous page. The current page number and the number of total pages are shown on the right of the down arrow “L”.

• The system can recognize up to 255 groups (or folders)

and up to 256 tracks. (This applies to the case where mixed MP3, JPEG and WMA files are recorded.)

• If no MP3, JPEG or WMA files are found in the group, the

group is not displayed.

• The DVD player can reproduce data recorded as per ISO

9660 Level 1, Level 2 or Joliet on the disc.

• It can also run a disk on which data is recorded in a multi-

session.

• For more details of recording systems, see the instruction

manual for the CD-R / CD-RW drive or the writing software.

Applicable MP3 file Remarks

Sampling frequency

Type

Applicable JPEG file Remarks

Size of image

Applicable WMA file Remarks

Sampling frequency

Bit rate 48–192kbps

Type WMA version 8

44.1kHz 48kHz

MPEG1 audio layer 3

Upper limit: 6300×5100 dots Lower limit: 32×32 dots

44.1kHz 48kHz

• It is prohibited to record MP3 sound on a digital device when connection is made digitally.

• MP3 files recorded at fixed bit rate of 112 kbps or higher are recommended.

• A JPEG image that extends beyond the screen is reduced so that it will be displayed within the screen.

• Those frequencies are applicable to WMA version 8 only, not to WMA version

• Ensure that the copyright function is set to off when preparing a WMA disc.

• A prohibition “disable” symbol will appear if the user attempts to run a non-reproducible file such as copyright-protected.

For discs of JPEG or Kodak picture CD:

• A JPEG or Kodak Picture CD menu appears.

• If all menu items cannot be displayed in the screen scope,

a prompt symbol “G” appears at the right bottom of the screen, indicating that the user can view remaining items on the next page. If another prompt symbol “H” appears, it indicates that the user can view other items on the previous page. The track number of the currently highlighted item and the total tracks are shown at the center bottom of the screen.

• If a prompt symbol “G” is shown at the right bottom, use the SKIP G button to view the next page. If another prompt symbol “H” is shown at the left bottom, use the SKIP H button to view the previous page.

• It may take some time until all menu items are displayed on the menu screen.

For JPEG, press the cursor buttons (K/L), or for Kodak Picture CD, press the cursor buttons (

B / K / L), select a desired group or track to be

s /

played, then press the PLAY or ENTER button.

• If an MP3 or WMA file is selected, reproduction will start from the selected track and go to the next one in turn.

• If a JPEG or Kodak picture CD file is selected, an image will be reproduced from the selected track and go to the next one in turn. A track is displayed for five seconds and then the next track is displayed. Every press on the cursor button B will turn the image clockwise by 90 degrees when an image is displayed. A press on the cursor button s will turn the image counterclockwise by 90 degrees.

• If a group is selected, press the cursor button K/L to select a desired group, then press the B, PLAY or ENTER button to select a track. If you press the PLAY or ENTER button, reproduction of the picture will start.

English

–19–

PLAYING A DISC

Notes on MP3, JPEG and WMA:

• Select “FIRST PLAY” and press the PLAY button, playback

from the top of the disc in the order of tracks and groups.

• The ninth and deeper hierarchies cannot be played.

• The name of group and track can be displayed in up to 25

characters. Alphabets, numerals underline, asterisk or space may not be displayed. Unrecognizable characters will be replaced with asterisks.

• Un-reproducible groups or tracks may be displayed

depending on the recording conditions.

• If the TOP MENU button is pressed when a file list is dis-

played, “FIRST PLAY” will be highlighted.

Press the STOP button, to stop playback.

Notes on Kodak picture CD:

• A press on the STOP button will highlight the previously

displayed track on the menu screen. Press the STOP button again or press the TOP MENU button, and the menu screen displays Tracks 1 to 6, where Track 1 is highlighted.

Slide Show Mode

JPEG

You can switch to the slide show mode during playback.

Press the MODE button during playback.

• The slide show mode screen will appear.

• The slide show mode cannot be switched when it is stopped, or from the file list screen or the Picture CD menu screen.

Press the ENTER button.

• The slide show mode will change. 1 The entire image appears in one time. 2 The image appears gradually and then disappears.

Track Selection

WMAJPEGMP3

Press the SEARCH MODE button during playback.

• The FILE LIST will appear.

Select a desired track using the cursor buttons (L/K/B/s).

• Press the Bbutton when you want to go to the next hierarchy.

• Press the previous hierarchy.

Press the PLAY button to start playing

NOTES:

•

Press the SEARCH MODE button to exit.

• Some selections may require additional time to be recognized.

• During play, a desired track can be directly searched. Just type in the TRACK number with the numeric buttons.

• If the typed TRACK number is not available, the “disable” symbol appears and the direct search mode is cancelled.

• Playback cannot be started from a desired time count.

• Pressing the SKIP button G or H will play the next or previous file.

• The SEARCH button is not effective for Picture CD.

button when you want to go back to the

Random Playback

WMAJPEGMP3

Press the RANDOM or MODE button while playback is stopped.

RANDOM

CD [DATA] TOTAL 0:45:55

RANDOM PROGRAM

--no indication--

Press the MODE button to exit.

On-Screen Information

You can check each file during playback.

Press the DISPLAY button.

• The name of the file currently in play will be displayed.

Press the DISPLAY button again to show the track number, the elapsed time, the repeat status, and the playback status at the top of the screen.

• will be displayed when the repeat play has been selected.

T - indicates Track repeat

G - indicates Group (folder)

repeat

A - indicates Disc repeat

Press the DISPLAY button again to exit.

• During program or random playback, each playback status will be displayed when you press the DISPLAY button. Then press the DISPLAY button again to exit.

TRACK 01

<Example: MP3>

TR 1/36 0:01:15

Press the PLAY button to play the tracks in random order.

• Random play starts.

• For a disc containing mixed MP3, JPEG and WMA

WMAJPEGMP3

–20–

files, random play of those files will be performed.

PLAYING A DISC

1.ENG DolbyD 5.1CH 48k/3

2.FRE DolbyD 5.1CH 48k/3

3.JPN DolbyD 5.1CH 48k/3

HELLO

Bon jour

Program

WMAJPEGMP3

This feature allows you to program a mp3 disc to play in a desired sequence.

Press the MODE button while playback is stopped.

• The PROGRAM screen will appear.

Press the K or L button to select a group, then press the ENTER button.

• A track selection screen appears.

Press the K or L button to select a track, then press the ENTER, button to save it in a program.

• Press the CLEAR button to erase the incorrect input.

• The programmed track is displayed in the right-hand screen.

• If the entire program cannot be displayed at once on the screen, “

• Pressing the belong to the one-level upper hierarchy than the cur-

L” appears to go to the next page.

s button will show a list of folders that

rently selected folder.

Press the PLAY button to start programmed play- back.

• Programmed play starts.

NOTES:

• Press the CLEAR button, and the last-programmed entry will be deleted.

• Press the RETURN button, and the STOP screen will show up with the program contents in memory.

• To stop programmed play, press the STOP button. Another press on the STOP button will reset the subsequent information.

• The program setting will be cancelled when the power is turned off or the disc tray is opened.

• Up to 99 tracks can be set in a program.

• If a disc in inserted that contains mixed MP3, JPEG and WMA files, program setting allows 99 tracks for combination of MP3, JPEG and WMA files.

• If eight or more tracks have been set in a program, the user can switch the right part of the screen with the SKIP button H or G.

PROGRAM

MP3

ABC DEF GHI JKL

1/1

ABC

PROGRAM

ABC TOTAL 0:03:30

1 3:30 2 4:30 3 5:00 4 3:10 5 5:10 6 1:30 7 2:30

1/2

1 3:30

PROGRAM

CD [AUDIO] TOTAL 0:03:30

1 3:30

1 3:30 2 4:30 3 5:00 4 3:10 5 5:10 6 1:30 7 2:30

1/2

1 3:30

Audio Language

The DVD player allows you to select a language during DVD disc (if multi language available) playback.

Press the AUDIO button during playback.

Press the AUDIO button repeatedly to select your desired language.

1/1

NOTES:

• Pressing the AUDIO button cycles the sound mode

through MAIN, SUB, MAIN + SUB.

• DVD-RW discs recorded in double sound (two languages ) can be played back in either sound mode of MAIN, SUB or MAIN + SUB.

• The sound mode cannot be changed during playback of discs not recorded in double sound. Pressing the AUDIO button may not work on some DVDs

• with multiple audio languages (e.g. DVDs which allow audio language setting on the disc menu).

Stereo Sound Mode

Press the AUDIO button repeatedly during playback to select between STEREO, L-CH or R-CH.

STEREO - both right and left channels are active (stereo) L-CH - only left channel is active R-CH - only right channel is active

STEREO

Both right and left channels are active (stereo).

DVD-V

English

L-CH

R-CH

Only the left channel is active.

Only the right channel is active.

NOTE:

• If the Virtual Surround setting is ON, the sound mode will be fixed to STEREO, and can not be changed.

• Stereo sound mode will not be changed when playing DTS CD.

–21–

PLAYING A DISC

Subtitle Language

DVD-V

The DVD player allows you to select a language for subtitle during DVD disc (if available) playback.

Press the SUBTITLE button during playback.

Press the SUBTITLE button repeatedly to select your desired subtitle language.

• The selected language will be displayed on the display bar at the top of the screen.

To turn off subtitles, press the SUBTITLE button repeatedly until OFF appears.

1.ENG/6

Subtitle 1

2.FRE/6

OFF

Subtitle 2

OFF

NOTES:

• Some discs allow audio language setting/subtitle language setting on the disc menu. (Operation varies between discs, so refer to the manual accompanying the disc.)

•

If the desired language is not shown after pressing the SUBTITLE button several times, the disc does not have subtitles in that language.

• If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Subtitle language setting. If you choose any other languages, ‘---’ will be displayed instead. (Refer to page 26.)

Camera Angle

DVD-V

Some DVD discs contain scenes which have been shot simultaneously from various angles. You can change the camera angle when the ( ) mark appears on the screen.

Press the ANGLE button during playback.

• The selected angle will be displayed on the display bar at the top of the screen.

Press the ANGLE button repeatedly to select your desired angle

1 / 8

Angle 1

Changing the On-Screen Display

DVD-V

You can check information about the current disc by pressing the DISPLAY button on the remote control.

Press the DISPLAY button during playback to show current Chapter

• The elapsed and remaining playing time of the current chapter will be displayed.

Press the DISPLAY button again to show current

9/49 0:00:00 -0:00:00

Title.

• The elapsed and remaining playing time of the current title will be displayed.

Press the DISPLAY button the third time.

• The BIT RATE and the current repeat setting will be displayed.

• If you are playing a dual layered disc, the layer number will also be displayed ( L0: Layer 0 is playing. L1: Layer 1 is playing).

If you are playing a DVD-RW with setting the PLAYLIST, the following will also be displayed.

ORG: Playing the ORIGINAL. PL: Playing the PLAYLIST.

Press the DISPLAY button the fourth time to remove

IIII

ORGT

the display.

WMAJPEGMP3CD

Press the DISPLAY button during playback, the current Track will be displayed on the TV screen.

• The elapsed and remaining playing time of the current track will be displayed.

Press the DISPLAY button again to show current Total Track.

• The elapsed and remaining playing time of the current total track will be displayed.

Press the DISPLAY button the third time to remove the display.

2 / 8

8 / 8

Angle 2

Angle 8

–22–

PLAYING A DISC

Marker Setup Screen

Use markers to memorise your favourite places on a disc.

Press the SEARCH MODE button four times (CD: three times) during playback.

•

The display screen and Markers will appear on the TV screen.

Press the s or B button to select 1, 2, 3, 4, 5, 6, 7, 8, 9, or 10 and ensure that “- : - - : - -” appears in the display.

When reaches the desired point, press the ENTER button.

• The Title or Track and elapsed playing time will appear in the TV screen.

To return to the Marker later, press the SEARCH MODE button four times

(CD: three times)

playback and the s or B button to choose the desired marker, then press the ENTER button.

NOTES:

• Opening the disc tray or turning off the power or select AC at step and press the ENTER button will erase all Markers.

• To clear a marker, using the s or B button, position the cursor on to the marker number to be cleared and press the CLEAR button.

• You can mark up to 10 points.

Press the SEARCH MODE or RETURN button to

exit.

1 2 3 4 5 6 7 8 9 10 AC

-- --:--:--

during

Black Level Setting

CDDVD-V

Adjust the Black Level Settings to make the black parts of the picture as bright as you preferred.

Press the MODE button during playback.

Press the ENTER button to switch ON/OFF

Press the

ON (Default) : Makes the dark parts brighter. OFF : Shows the original picture as recorded.

MODE or RETURN button to exit.

DVD-V

English

Virtual Surround

DVD-V

You can enjoy stereophonic visual space on your existing 2 channel stereo system.

Press the VIRTUAL button on the front panel or press the

OFF

MODE button twice during playback

Press the

VIRTUAL or ENTER

button to set it

1(Natural effect), 2(Emphasized effect) or OFF.

Press the RETURN button to exit.

WMAMP3CD

Press the VIRTUAL button on the front panel or press the MODE button during playback

Press the

VIRTUAL or ENTER

button to set

1(Natural effect), 2(Emphasized effect) or OFF.

Press the RETURN button to exit.

(for CD play only):

NOTE

• Select Virtual Surround OFF or adjust the volume down if the sound is distorted.

–23–

DVD SETUP

In Setup menu, QUICK mode and CUSTOM mode are availale. QUICK mode consists of the setting menus often needed, and you can make all settings required in CUSTOM mode. You can make the settings of the items with mark in QUICK mode.

QUICK

Language Setting Display Setting

Language options are not available with some discs.

Press the SETUP button in STOP mode.

Press the B button to select

CUSTOM, then press the

ENTER button.

• CUSTOM mode will appear.

Press the s or B button to select LANGUAGE, then the EN-

TER button to confirm.

Press the K or L button to select the below items,

LANGUAGE

DIALOG ORIGINAL SUBTITLE OFF DISC MENU ENGLISH OSD ENGLISH

then press the ENTER button.

DIALOG

SUBTITLE

DISC MENU

(Default : ORIGINAL)

• Sets the audio language.

(Default : OFF)

• Sets the subtitle language.

(Default : ENGLISH)

• Sets the language for DVD Menu.

LANGUAGE DIALOG ORIGINAL ENGLISH FRENCH SPANISH GERMAN ITALIAN SWEDISH L

LANGUAGE SUBTITLE OFF ENGLISH FRENCH SPANISH GERMAN ITALIAN SWEDISH L

LANGUAGE DISC MENU ENGLISH FRENCH SPANISH GERMAN ITALIAN SWEDISH DUTCH L

OSD (Default : ENGLISH)

• Sets the language for the OnScreen display.

Press the K or L button to select a setting, then

QUICK

LANGUAGE OSD ENGLISH FRANÇAIS ESPAÑOL

press the ENTER button.

•

If OTHERS is selected in the AUDIO, SUBTITLE or DISC MENU screen, press four-digit number to enter the code for the desired language. (Refer to the language code list below). Only the languages supported by the disc can be selected.

•

Press the SETUP button to exit.

NOTE:

• Language Setting for Dialog and Subtitle is not available

with some discs. Then use the AUDIO and SUBTITLE buttons. Details are on page 21, or 22.

You can change certain aspects of the DVD display screens, on-screen messages and the display panel on the front of the DVD player.

Press the SETUP button in STOP mode.

Press the B button to select CUSTOM, then press the ENTER button.

•

CUSTOM mode will appear.

Press the s or B button to select DISPLAY, then the ENTER button to confirm.

Press the K or L button to select the below items, then

DISPLAY

TV ASPECT

4:3 LETTER BOX PANEL DISPLAY BRIGHT ANGLE ICON ON AUTO POWER OFF ON

press the ENTER button.

TV ASPECT TER BOX)

• Press the K or L button for an

item selection, then press the EN- TER button.

•

Select 4:3 LETTER BOX for a black bars appears on top and bottom of the screen.

• Select 4:3 PAN - SCAN for a full height picture with both sides trimmed.

•

Select 16:9 WIDE if a wide-screen TV is connected to the DVD player.

PANEL DISPLAY BRIGHT)

• Press the K or L button item select BRIGHT, DIM and AUTO DIM, then press the ENTER button.

• This adjust the brightness of the display panel with the factory default BRIGHT.

• When AUTO DIM is selected, the display dims only during playback.

ANGLE ICON

• Press the ENTER button repeatedly to turn Angle mark ON or OFF.

AUTO POWER OFF

• Press the ENTER button repeatedly to turn Auto Power ON or OFF.

• It will turn the DVD player to off automatically after 35 minutes of no use.

Press the SETUP button to exit.

(Default : 4:3 LET-

QUICK

(Default :

(Default : ON)

for an

DISPLAY TV ASPECT

4:3 LETTER BOX 4:3 PAN & SCAN 16

:9 WIDE

DISPLAY PANEL DISPLAY

BRIGHT DIMMER AUTO

DISPLAY

TV ASPECT

4:3 LETTER BOX PANEL DISPLAY BRIGHT ANGLE ICON ON AUTO POWER OFF ON

DISPLAY

TV ASPECT

4:3 LETTER BOX PANEL DISPLAY BRIGHT ANGLE ICON ON AUTO POWER OFF ON

NOTES:

•

Be sure to press the SETUP button, or the setting will not work.

• You can also choose the item by pressing the numbers.

–24–

English

–25–

• ALL Parental lock is cancelled.

• Level 8 DVD software of any grade (adult/general/children) can be played back.

• Levels 7 to 2 Only DVD software intended for general use and children can be played back.

• Level 1 Only DVD software intended for children can be played back, with those intended for adult and general use prohibited.

CONTROL LEVELS

DVD SETUP

Audio Setting

Choose the appropriate Audio settings for your equipment as it only affect during the playback of DVD discs of the DVD player.

Press the SETUP button in STOP mode. Press the B button to select CUSTOM, then press

the ENTER button.

• CUSTOM mode will appear.

Press the s or B button to select AUDIO, then the ENTER button to confirm.

Press the K or L button to select the below items, then press the ENTER button.

DRC (Dynamic Range Control) (Default : OFF)

• To compress the range of sound volume.

DOLBY DIGITAL

(Default : ON)

Set to ON when the player is connected to Dolby Digital Decoder.

(ON : Output by Dolby Digital) (OFF : Convert the Dolby Digital to

PCM)

DTS (Default : ON)

ON : Output by DTS sound Set to ON when the unit is connected to DTS Decoder.

LPCM SELECT

(Default : OFF)

• Set to ON when outputting in 48kHz.

When playing disc with copyright Protection

• If you select OFF, copyright protection will be activated and sound will be down sampled at 48kHz.

Press the SETUP button to exit.

QUICK

Ratings Control

Ratings Control limits playback of discs with unsuitable audience ratings. A four digit code established by the user will unlock the parental lock. This feature allows you to prevent discs with objectionable scenes from being played by your children.

RATING LEVEL

Rating Level allows you to set the rating level of your DVD discs. Playback will stop if the disc’s ratings exceed the level you set.

Press the SETUP button in STOP mode. Press the B button to select CUSTOM, then press the ENTER button. Press the s or B button to select RATING, then press the ENTER button. Enter your four-digit password then press the ENTER button.

Press the K or L button to select RATING LEVEL, then press the ENTER button.

Press the K or L button to select the desired level.

Press the SETUP button to exit.

NOTES:

• When doing this for the first time, enter any 4 digits. (except for 4737) That number will be used as the password from the second time onward.

•

To change the password, press the K or L button to select CHANGE at step , then press the ENTER button. Enter the fourdigit pass-word, then press the ENTER button.

• With some DVDs, it may be difficult to find if they are compatible with parental lock. Be sure to check if the parental lock function operates in the way that you have set.

• Record the password in case you forget it.

IF YOU FORGET THE PASSWORD

Press 4, 7, 3, 7 at step 4.

•

Password will be cleared and rating level will be set to ALL.

Repeat steps 5-7 to re-establish the parental lock.

AUDIO

DRC DOLBY DIGITAL ON DTS ON LPCM SELECT OFF

AUDIO

DRC DOLBY DIGITAL ON DTS ON LPCM SELECT OFF

AUDIO

DRC DOLBY DIGITAL ON DTS ON LPCM SELECT OFF

AUDIO

DRC DOLBY DIGITAL ON DTS ON LPCM SELECT OFF

OFF

RATINGS

Please enter a 4-digit password.

RATINGS

RATING LEVEL ALL CHANGE

RATINGS RATING LEVEL

ALL 8 7 [NC-17] 6 [R] 5 4 [PG13] 3 [PG]

AUDIO

DRC DOLBY DIGITAL ON DTS ON LPCM SELECT OFF

OFF

DVD SETUP

Language Code Language Code Language Code Language Code

Abkhazian 4748 Afar 4747 Afrikaans 4752 Albanian 6563 Amharic 4759 Arabic 4764 Armenian 5471 Assamese 4765 Aymara 4771 Azerbaijani 4772 Bashkir 4847 Basque 5167 Bengali;Bangla 4860 Bhutani 5072 Bihari 4854 Bislama 4855 Breton 4864 Bulgarian 4853 Burmese 5971 Byelorussian 4851

Cambodian 5759 Catalan 4947 Chinese [CHI] 7254 Corsican 4961 Croatian 5464 Czech 4965 Danish [DAN] 5047 Dutch [DUT] 6058 English [ENG] 5160 Esperanto 5161 Estonian 5166

Faroese 5261 Fiji 5256 Finnish [FIN] 5255 French [FRE] 5264

If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language setting on page 22. If you choose any other languages, ‘---’ will be displayed instead. (3 letter language code is written in bracket.)

A-B

C-E

F-H

Frisian 5271 Galician 5358 Georgian 5747 German [GER] 5051 Greek [GRE] 5158 Greenlandic 5758 Guarani 5360 Gujarati 5367 Hausa 5447 Hebrew 5569 Hindi 5455 Hungarian [HUN] 5467

Icelandic [ICE] 5565 Indonesian 5560 Interlingua 5547 Interlingue 5551 Inupiak 5557 Irish [IRI] 5347 Italian [ITA] 5566 Japanese [JPN] 5647 Javanese 5669 Kannada 5760 Kashmiri 5765 Kazakh 5757 Kinyarwanda 6469 Kirghiz 5771 Kirundi 6460 Korean [KOR] 5761 Kurdish 5767

Laothian 5861 Latin 5847 Latvian;Lettish 5868 Lingala 5860 Lithuanian 5866 Macedonian 5957 Malagasy 5953

I-K

L-N

Malay 5965 Malayalam 5958 Maltese 5966 Maori 5955 Marathi 5964 Moldavian 5961 Mongolian 5960 Nauru 6047 Nepali 6051 Norwegian [NOR] 6061

Occitan 6149 Oriya 6164 Oromo(Afan) 6159 Panjabi 6247 Pashto;Pushto 6265 Persian 5247 Polish 6258 Portuguese [POR] 6266 Quechua 6367 Rhaeto-Romance 6459 Romanian [RUM] 6461 Russian [RUS] 6467

Samoan 6559 Sangho 6553 Sanskrit 6547 Scots Gaelic 5350 Serbian 6564 Serbo-Croatian 6554 Sesotho 6566 Setswana 6660 Shona 6560 Sindhi 6550 Singhalese 6555 Siswat 6565 Slovak 6557 Slovenian 6558

O-R

Somali 6561 Spanish [SPA] 5165 Sundanese 6567 Swahili 6569 Swedish [SWE] 6568

Tagalog 6658 Tajik 6653 Tamil 6647 Tatar 6666 Telugu 6651 Thai 6654 Tibetan 4861 Tigrinya 6655 Tonga 6661 Tsonga 6665 Turkish [TUR] 6664 Turkmen 6657 Twi 6669

Ukrainian 6757 Urdu 6764 Uzbek 6772 Vietnamese 6855 Volapuk 6861 Welsh 4971 Wolof 6961 Xhosa 7054 Yiddish 5655 Yoruba 7161 Zulu 7267

U-Z

–26–

+ 60 hidden pages

Denon DVD-910 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

DVD-910

PRECAUTIONS

TABLE OF CONTENTS

INTRODUCTION

ABOUT THE DISCS

FEATURES

FUNCTIONAL OVERVIEW

HOOK UPS

PLAYING A DISC

DVD SETUP