Specifications and Main Features
- Model: DRA-435R / DRA-335R
- Continuous Power Output:
- DRA-435R: up to 55 watts per channel minimum rms for 20hz to 20khz at load of 8 ohm
- DRA-335R: 40 watts / channel at loading of 8 ohms and 20 – 20khz.
- Max Total Harmonic Distortion: up to 0.05%.
- Frequency Response:
- DRA-435R: band widths of 10hz to 40khz
- DRA-335R: band widths of 10hz to 40khz
- Input Sensitivity:
- PHONO: 2.5mV at 48k ohms
- CD, VIDEO: 150mV at 29k ohms
- Maximum Input Level (at 1 kHz):
- MM – PHONO: 120 mV
- Signal to Noise Ratio:
- PHONO: 78 dB for mV input of 5.0 mV; CD, VIDEO: 96 dB
- Tone Controls:
- BASS: +10dB at 100Hz;
- TREBLE: +10dB at 10kHz;
- VARIABLE LOUDNESS: 10 settings, 00 – 10db at 50hz and 00 – 5dB at 10KHz
- PRE - OUT Terminals (DRA-435R only): 2V (at 100kohms load)
- Dimensions:
- W: 434mm (17-3/32”), H: 120mm (4-23/32”), D: 312 mm (12-9/32”)
- Weight:
- DRA-435R: 6.7kg (14 lbs 12 oz) DRA-335R: 6.4kg (14 lbs 2 oz)
- Power Consumption:
- DRA-435R: 264 W
- DRA-335R: 180 W
- Power Supply: AC 120V, 60 Hz
- Remote Control Model: RC-129 (for DRA-435R) / RC-129A (for DRA-335R)
- Tuner
- FM Frequency Range: 87.5-108 MHz
- AM Frequency Range: 520-1710 kHz
Frequently Asked Questions
- How much power does the DRA-435R deliver? When does it reach the maximum output?
- The DRA-435R sustains power output of 55 Watts During operation , the continuous power output is estimated to be 55 watts for each channel with an 8 ohm load per channel.
- Does the phono section have a specific input? What kind?
- The phono section is designed specifically for use with MM cartridges which are rated 2.5mV input sensitivity at 47Kohms.
- Can I modify the bass and treble levels?
- Yes. Bass can be set to +10 dB at 100Hz and treble can be set to +10 dB at 10kHz.
- Is it possible to connect two sets of speakers?
- Yes, it is possible to connect two speaker systems and designate them Systems A or B.
- What is the weight of the DRA-335R?
- The weight of the DRA-335 R is 6.4 kg which is equal to 14 lbs two ounces.
- Does the receiver have a remote control?
- The receiver is supplied with a remote control RC-129 for DRA-435R, and for DRA-335R the model is RC-129A.
- What power supply is required for the device?
- It requires AC Power Supply of 120 Volts, 60 Hz.
- What is the total harmonic distortion level?
- The total harmonic distortion is the level not more than o.05%.
User Manual
Page 1
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Page 31
Page 32
Loading...