Denon AVR-1910E2 User Manual

AV SURROUND RECEIVER

AVR-1910

Owner’s Manual Bedienungsanleitung Manuel de l’Utilisateur Manuale delle istruzioni Manual del usuario Gebruiksaanwijzing Bruksanvisning

Button illustrations used in this manual for operation explanation are for the Remote Control Unit.

You can operate the unit using the button of the same name on the front panel of the unit.

Die in diesem Handbuch verwendeten Tasten-Illustrationen für die Betriebserklärung beziehen sich auf die Fernbedienung.

Sie können das Gerät mit der gleichnamigen Taste an der Frontkonsole des Gerätes bedienen.

Les illustrations des boutons présentes dans ce manuel servent à expliquer le fonctionnement de la télécommande.

Vous pouvez contrôler l’appareil à l’aide du bouton portant le même nom sur la façade de l’appareil.

Le illustrazioni dei pulsanti mostrate in questo manuale di spiegazione si riferiscono al telecomando.

E’ possibile adoperare l’unità utilizzando i pulsanti del nome corrispondente presenti sul pannello frontale dell'unità.

Las ilustraciones de los botones utilizadas en este manual con propósitos de explicación son para la unidad del mando a distancia.

Puede operar la unidad utilizando el botón del mismo nombre en el panel delantero de la unidad.

De gebruikte toetsillustraties in deze handleiding voor uitleg van de bediening zijn voor de afstandsbediening.

U kunt het toestel bedienen door de toets met dezelfde naam op het voorpaneel van het toestel te gebruiken.

Bilder på knappar i denna bruksanvisning för att förklara användningen gäller fjärrkontrollen.

Du kan också använda knapparna med samma namn på frontpanelen på enheten.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ITALIANO ESPAÑOL NEDERLANDS SVENSKADEUTSCH FRANCAISENGLISH

SAFETY PRECAUTIONS

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning ﬂash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

IMPOTANT SAFETY

INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

10. Only use attachments/accessories speciﬁed by the manufacturer.

11. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

12. Unplug this apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. Batteries shall not be exposed to excessive heat such as sunshine, ﬁre or the like.

’s instructions.

CAUTION:

To completely disconnect this product from the mains, disconnect the plug from the wall socket outlet. The mains plug is used to completely interrupt the power supply to the unit and must be within easy access by the user.

VORSICHT:

Um dieses Gerät vollständig von der Stromversorgung abzutrennen, ziehen Sie bitte den Stecker aus der Wandsteckdose. Der Netzstecker wird verwendet, um die Stromversorgung zum Gerät völlig zu unterbrechen; er muss für den Benutzer gut und einfach zu erreichen sein.

PRECAUTION:

Pour déconnecter complètement ce produit du courant secteur, débranchez la prise de la prise murale. La prise secteur est utilisée pour couper complètement l’alimentation de l’appareil et l’utilisateur doit pouvoir y accéder facilement.

ATTENZIONE:

Per scollegare completamente questo prodotto dalla rete di alimentazione elettrica, scollegare la spina dalla relativa presa a muro. La spina di rete viene utilizzata per interrompere completamente l’alimentazione all’unità e deve essere facilmente accessibile all’utente.

PRECAUCIÓN:

Para desconectar completamente este producto de la alimentación eléctrica, desconecte el enchufe del enchufe de la pared. El enchufe de la alimentación eléctrica se utiliza para interrumpir por completo el suministro de alimentación eléctrica a la unidad y debe de encontrarse en un lugar al que el usuario tenga fácil acceso.

WAARSCHUWING:

Om de voeding van dit product volledig te onderbreken moet de stekker uit het stopcontact worden getrokken. De netstekker wordt gebruikt om de stroomtoevoer naar het toestel volledig te onderbreken en moet voor de gebruiker gemakkelijk bereikbaar zijn.

FÖRSIKTIHETSMÅTT:

Koppla loss stickproppen från eluttaget för att helt skilja produkten från nätet. Stickproppen används för att helt bryta strömförsörjningen till apparaten, och den måste vara lättillgänglig för användaren.

NOTE ON USE / HINWEISE ZUM GEBRAUCH / OBSERVATIONS RELATIVES A L’UTILISATION / NOTE SULL’USO /

NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA ANGÅENDE ANVÄNDNINGEN

CAUTION:

• The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, tablecloths, curtains, etc.

• No naked ﬂame sources, such as lighted candles, should be placed on the unit.

• Observe and follow local regulations regarding battery disposal.

• Do not expose the unit to dripping or splashing ﬂuids.

• Do not place objects ﬁlled with liquids, such as vases, on the unit.

ACHTUNG:

• Die Belüftung sollte auf keinen Fall durch das Abdecken der Belüftungsöffnungen durch Gegenstände wie beispielsweise Zeitungen, Tischtücher, Vorhänge o. Ä. behindert werden.

• Auf dem Gerät sollten keinerlei direkte Feuerquellen wie beispielsweise angezündete Kerzen aufgestellt werden.

• Bitte beachten Sie bei der Entsorgung der Batterien die örtlich geltenden Umweltbestimmungen.

• Das Gerät sollte keiner tropfenden oder spritzenden Flüssigkeit ausgesetzt werden.

• Auf dem Gerät sollten keine mit Flüssigkeit gefüllten Behälter wie beispielsweise Vasen aufgestellt werden.

ATTENTION:

• La ventilation ne doit pas être gênée en recouvrant les ouvertures de la ventilation avec des objets tels que journaux, rideaux, tissus, etc.

• Aucune ﬂamme nue, par exemple une bougie, ne doit être placée sur l’appareil.

• Veillez à respecter les lois en vigueur lorsque vous jetez les piles usagées.

• L’appareil ne doit pas être exposé à l’eau ou à l’humidité.

• Ne pas poser d’objet contenant du liquide, par exemple un vase, sur l’appareil.

ATTENZIONE:

• Le aperture di ventilazione non devono essere ostruite coprendole con oggetti, quali giornali, tovaglie, tende e così via.

• Non posizionate sull’unità ﬁamme libere, come ad esempio candele accese.

• Prestate attenzione agli aspetti legati alla tutela dell’ambiente nello smaltimento delle batterie.

• L’apparecchiatura non deve essere esposta a gocciolii o spruzzi.

• Non posizionate sull’unità alcun oggetto contenente liquidi, come ad esempio i vasi.

PRECAUCIÓN:

• La ventilación no debe quedar obstruida por haberse cubierto las aperturas con objetos como periódicos, manteles, cortinas, etc.

• No debe colocarse sobre el aparato ninguna fuente inﬂamable sin protección, como velas encendidas.

• A la hora de deshacerse de las pilas, respete la normativa para el cuidado del medio ambiente.

• No exponer el aparato al goteo o salpicaduras cuando se utilice.

• No colocar sobre el aparato objetos llenos de líquido, como jarros.

WAARSCHUWING:

• De ventilatie mag niet worden belemmerd door de ventilatieopeningen af te dekken met bijvoorbeeld kranten, een tafelkleed, gordijnen, enz.

• Plaats geen open vlammen, bijvoorbeeld een brandende kaars, op het apparaat.

• Houd u steeds aan de milieuvoorschriften wanneer u gebruikte batterijen wegdoet.

• Stel het apparaat niet bloot aan druppels of spatten.

• Plaats geen voorwerpen gevuld met water, bijvoorbeeld een vaas, op het apparaat.

OBSERVERA:

• Ventilationen bör inte förhindras genom att täcka för ventilationsöppningarna med föremål såsom tidningar, bordsdukar, gardiner osv.

• Inga blottade brandkällor, såsom tända ljus, får placeras på apparaten.

• Tänk på miljöaspekterna när du bortskaffar batterier.

• Apparaten får inte utsättas för vätska.

• Placera inte föremål fyllda med vätska, t.ex. vaser, på apparaten.

• Avoid high temperatures. Allow for sufﬁcient heat dispersion when installed in a rack.

• Vermeiden Sie hohe Temperaturen. Beachten Sie, dass eine ausreichende Belüftung gewährleistet wird, wenn das Gerät auf ein Regal gestellt wird.

• Eviter des températures élevées.

Tenir compte d’une dispersion de chaleur sufﬁsante lors de

l’installation sur une étagère.

• Evitate di esporre l’unità a temperature elevate. Assicuratevi che vi sia un’adeguata dispersione del calore quando installate l’unità in un mobile per componenti audio.

• Evite altas temperaturas.

Permite la suﬁciente dispersión del calor cuando está

instalado en la consola.

• Vermijd hoge temperaturen.

Zorg er bij installatie in een audiorack voor, dat de door

het toestel geproduceerde warmte goed kan worden afgevoerd.

• Undvik höga temperaturer.

Se till att det ﬁnns möjlighet till god värmeavledning vid

montering i ett rack.

• Handle the power cord carefully.

Hold the plug when unplugging the cord.

• Gehen Sie vorsichtig mit dem Netzkabel um.

Halten Sie das Kabel am Stecker, wenn Sie den Stecker

herausziehen.

• Manipuler le cordon d’alimentation avec précaution.

Tenir la prise lors du débranchement du cordon.

• Manneggiate il cavo di alimentazione con attenzione. Tenete ferma la spina quando scollegate il cavo dalla presa.

• Maneje el cordón de energía con cuidado.

Sostenga el enchufe cuando desconecte el cordón de

energía.

• Hanteer het netsnoer voorzichtig.

Houd het snoer bij de stekker vast wanneer deze moet

worden aan- of losgekoppeld.

• Hantera nätkabeln varsamt.

Håll i kabeln när den kopplas från el-uttaget.

• Keep the unit free from moisture, water, and dust.

• Halten Sie das Gerät von Feuchtigkeit, Wasser und Staub fern.

• Protéger l’appareil contre l’humidité, l’eau et la poussière.

• Tenete l’unità lontana dall’umidità, dall’acqua e dalla polvere.

• Mantenga el equipo libre de humedad, agua y polvo.

• Laat geen vochtigheid, water of stof in het apparaat binnendringen.

• Utsätt inte apparaten för fukt, vatten och damm.

• Unplug the power cord when not using the unit for long periods of time.

• Wenn das Gerät längere Zeit nicht verwendet werden soll, trennen Sie das Netzkabel vom Netzstecker.

• Débrancher le cordon d’alimentation lorsque l’appareil n’est pas utilisé pendant de longues périodes.

• Scollegate il cavo di alimentazione quando prevedete di non utilizzare l’unità per un lungo periodo di tempo.

• Desconecte el cordón de energía cuando no utilice el equipo por mucho tiempo. Neem altijd het netsnoer uit het stopkontakt wanneer het

• apparaat gedurende een lange periode niet wordt gebruikt.

• Koppla loss nätkabeln om apparaten inte kommer att användas i lång tid.

* (For apparatuses with ventilation holes)

• Do not obstruct the ventilation holes.

• Decken Sie den Lüftungsbereich nicht ab.

• Ne pas obstruer les trous d’aération.

• Non coprite i fori di ventilazione.

• No obstruya los oriﬁcios de ventilación.

• De ventilatieopeningen mogen niet worden beblokkeerd.

• Täpp inte till ventilationsöppningarna.

• Do not let foreign objects into the unit. Lassen Sie keine fremden Gegenstände in das Gerät kommen.

•

• Ne pas laisser des objets étrangers dans l’appareil.

• Non inserite corpi estranei all’interno dell’unità.

• No deje objetos extraños dentro del equipo.

• Laat geen vreemde voorwerpen in dit apparaat vallen.

• Se till att främmande föremål inte tränger in i apparaten.

• Do not let insecticides, benzene, and thinner come in contact with the unit.

• Lassen Sie das Gerät nicht mit Insektiziden, Benzin oder Verdünnungsmitteln in Berührung kommen.

• Ne pas mettre en contact des insecticides, du benzène et un diluant avec l’appareil.

• Assicuratevi che l’unità non entri in contatto con insetticidi, benzolo o solventi.

• No permita el contacto de insecticidas, gasolina y diluyentes con el equipo.

• Voorkom dat insecticiden, benzeen of verfverdunner met dit toestel in contact komen.

• Se till att inte insektsmedel på spraybruk, bensen och thinner kommer i kontakt med apparatens hölje.

• Never disassemble or modify the unit in any way.

• Versuchen Sie niemals das Gerät auseinander zu nehmen oder zu verändern.

• Ne jamais démonter ou modiﬁer l’appareil d’une manière ou d’une autre.

• Non smontate né modiﬁcate l’unità in alcun modo.

• Nunca desarme o modiﬁque el equipo de ninguna manera.

• Dit toestel mag niet gedemonteerd of aangepast worden.

• Ta inte isär apparaten och försök inte bygga om den.

DEUTSCHFRANCAISITALIANOESPAÑOLNEDERLANDSSVENSKA ENGLISH

ITALIANO ESPAÑOL NEDERLANDS SVENSKADEUTSCH FRANCAISENGLISH

• DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product, to which this

declaration relates, is in conformity with the following standards: EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3. Following the provisions of 2006/95/EC and 2004/108/EC Directive.

• ÜBEREINSTIMMUNGSERKLÄRUNG

Wir erklären unter unserer Verantwortung, daß dieses Produkt, auf das

sich diese Erklärung bezieht, den folgenden Standards entspricht: EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3. Entspricht den Verordnungen der Direktive 2006/95/EC und 2004/108/EC.

• DECLARATION DE CONFORMITE

Nous déclarons sous notre seule responsabilité que l’appareil, auquel se

réfère cette déclaration, est conforme aux standards suivants: EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3. D’après les dispositions de la Directive 2006/95/EC et 2004/108/EC.

• DICHIARAZIONE DI CONFORMITÀ

Dichiariamo con piena responsabilità che questo prodotto, al quale la

nostra dichiarazione si riferisce, è conforme alle seguenti normative: EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3. In conformità con le condizioni delle direttive 2006/95/EC e 2004/108/EC. QUESTO PRODOTTO E’ CONFORME AL D.M. 28/08/95 N. 548

• DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que este producto al

que hace referencia esta declaración, está conforme con los siguientes

estándares: EN60065, EN55013, EN55020, EN61000-3-2 y EN61000-3-3. Siguiendo las provisiones de las Directivas 2006/95/EC y 2004/108/EC.

• EENVORMIGHEIDSVERKLARING

Wij verklaren uitsluitend op onze verantwoordelijkheid dat dit produkt,

waarop deze verklaring betrekking heeft, in overeenstemming is met de

volgende normen: EN60065, EN55013, EN55020, EN61000-3-2 en EN61000-3-3. Volgens de bepalingen van de Richtlijnen 2006/95/EC en 2004/108/EC.

• ÖVERENSSTÄMMELSESINTYG

Härmed intygas helt på eget ansvar att denna produkt, vilken detta intyg

avser, uppfyller följande standarder: EN60065, EN55013, EN55020, EN61000-3-2 och EN61000-3-3. Enligt stadgarna i direktiv 2006/95/EC och 2004/108/EC.

DENON EUROPE Division of D&M Germany GmbH An der Landwehr 19, Nettetal, D-41334 Germany

A NOTE ABOUT RECYCLING:

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with the local recycling regulations. When discarding the unit, comply with local rules or regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with the local regulations concerning battery disposal. This product and the supplied accessories, excluding the batteries, constitute the applicable product according to the WEEE directive.

HINWEIS ZUM RECYCLING:

Das Verpackungsmaterial dieses Produktes ist zum Recyceln geeignet und kann wieder verwendet werden. Bitte entsorgen Sie alle Materialien entsprechend der örtlichen Recycling-Vorschriften. Beachten Sie bei der Entsorgung des Gerätes die örtlichen Vorschriften und Bestimmungen. Die Batterien dürfen nicht in den Hausmüll geworfen oder verbrannt werden; bitte entsorgen Sie die Batterien gemäß der örtlichen Vorschriften. Dieses Produkt und das im Lieferumfang enthaltene Zubehör (mit Ausnahme der Batterien!) entsprechen der WEEE-Direktive.

UNE REMARQUE CONCERNANT LE RECYCLAGE:

Les matériaux d’emballage de ce produit sont recyclables et peuvent être réutilisés. Veuillez disposer des matériaux conformément aux lois sur le recyclage en vigueur. Lorsque vous mettez cet appareil au rebut, respectez les lois ou réglementations en vigueur. Les piles ne doivent jamais être jetées ou incinérées, mais mises au rebut conformément aux lois en vigueur sur la mise au rebut des piles. Ce produit et les accessoires inclus, à l’exception des piles, sont des produits conformes à la directive DEEE.

NOTA RELATIVA AL RICICLAGGIO:

I materiali di imballaggio di questo prodotto sono riutilizzabili e riciclabili. Smaltire i materiali conformemente alle normative locali sul riciclaggio. Per lo smaltimento dell’unità, osservare le normative o le leggi locali in vigore. Non gettare le batterie, né incenerirle, ma smaltirle conformemente alla normativa locale sui riﬁuti chimici. Questo prodotto e gli accessori inclusi nell’imballaggio sono applicabili alla direttiva RAEE, ad eccezione delle batterie.

ACERCA DEL RECICLAJE:

Los materiales de embalaje de este producto son reciclables y se pueden volver a utilizar. Disponga de estos materiales siguiendo los reglamentos de reciclaje de su localidad. Cuando se deshaga de la unidad, cumpla con las reglas o reglamentos locales. Las pilas nunca deberán tirarse ni incinerarse. Deberá disponer de ellas siguiendo los reglamentos de su localidad relacionados con los desperdicios químicos. Este producto junto con los accesorios empaquetados es el producto aplicable a la directiva RAEE excepto pilas.

EEN AANTEKENING MET BETREKKING TOT DE RECYCLING:

Het inpakmateriaal van dit product is recycleerbaar en kan opnieuw gebruikt worden. Er wordt verzocht om zich van elk afvalmateriaal te ontdoen volgens de plaatselijke voorschriften. Volg voor het wegdoen van de speler de voorschriften voor de verwijdering van wit- en bruingoed op. Batterijen mogen nooit worden weggegooid of verbrand, maar moeten volgens de plaatselijke voorschriften betreffende chemisch afval worden verwijderd. Op dit product en de meegeleverde accessoires, m.u.v. de batterijen is de richtlijn voor afgedankte elektrische en elektronische apparaten (WEEE) van toepassing.

OBSERVERA ANGÅENDE ÅTERVINNING:

Produktens emballage är återvinningsbart och kan återanvändas. Kassera det enligt lokala återvinningsbestämmelser. När du kasserar enheten ska du göra det i överensstämmelse med lokala regler och bestämmelser. Batterier får absolut inte kastas i soporna eller brännas. Kassera dem enligt lokala bestämmelser för kemiskt avfall. Denna apparat och de tillbehör som levereras med den uppfyller gällande WEEE-direktiv, med undantag av batterierna.

III

ENGLISH

n Contents

Getting Started

Flow of operations through playback ········································· 2

Accessories ··················································································2

Cautions on Handling ···································································3 Cautions on Installation ·······························································3 About the Remote Control Unit···················································3

Inserting the Batteries ··································································3 Operating Range of the Remote Control Unit ······························3

Part Names and Functions ··························································· 4

Front Panel ····················································································4 Display ··························································································5 Rear Panel ·····················································································6 Remote Control Unit ····································································· 7

Connections

Important Information ··································································8

Cables Used for Connections ·······················································8 Converting Input video signals for Output (Video Conversion Function) ·························································9 How the on-screen display is displayed depending on the video input signal····················································································9

Installing/Setting the Speakers ················································· 10 Connecting the Speakers ···························································11 Connecting Devices ····································································12 Connecting Devices not Equipped with HDMI terminals ········ 13 Once Connections are Completed ············································· 17

Turning the Power On ································································· 17 Turning the Power Off ································································· 17

Settings

Menu map ···················································································· 18 Examples of On-screen Display and Front Display ·················· 19 Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup) ······································ 20 Making detailed settings (Manual Setup)·································25 Making the input settings (Input Setup)···································32

Playback

Playing Components ··································································· 37

Playing Blu-ray Disc / DVD Players ·············································· 37 iPod® Playback ··········································································· 37 Listening to FM/AM Broadcasts ·················································39 Operations During Playback ························································41

Selecting the Surround Mode ···················································· 42

q Playing sources according to the sources’ audio signal format/ number of channels (Standard Playback) ···································· 42

w Playing in a DENON original surround mode ··························43 e Direct Playback ·······································································43 r Stereo Playback ······································································43 t Playing the Pure Direct mode ················································43

Adjusting the Sound Field Effects (Parameter) ························44

Adjusting the sound ﬁeld effects (Surround Parameter) ·············44 Adjusting the tone (Tone Control) ···············································45 Making the MultEQ, Dynamic EQ and Dynamic Volume settings (Audyssey Settings) ····································································46 Adjust tonal quality for each speaker using graphic equalizer (Manual EQ) ················································································47 Restoring compressed audio to nearly pre-compressed conditions for playback (RESTORER)····························································47 Adjusting the audio delay time while watching the picture (Audio Delay) ···············································································47

Checking the Status (Information) ·····························48

Convenient functions

HDMI Control Function ·······························································49 Setting the power to standby after a certain amount of time (Sleep Timer Function) ·······························································49 Adjust the volume of the different speakers ····························50 Saving frequently used settings (Quick Select Function) ······· 50

MAIN ZONE settings ··································································50 ZONE2 settings···········································································50

Various memory functions ························································· 50

Playing 2-Channel Sound in ZONE2 (Multizone function)···························································51

Operating the Connected Devices by Remote Control Unit

Registering Preset Codes ···························································52 Operating Registered Devices ···················································52 Assigning buttons that are Not Used to Operate Other Devices (Punch Through Function) ·························································· 54

Other Information ·······························································55

Troubleshooting···································································61

Restoring all the settings to as they were at the time of purchase (Resetting the Microprocessor) ································· 63

Speciﬁcations ········································································64

List of preset codes ··································End of this manual



ENGLISH

Connections Playback Remote Control Information Troubleshooting Speciﬁ cationsMulti-ZoneSettings

Perform the operations leading to playback on the AVR-1910 in the order shown below.

Connections

⇩

Installing/Setting the Speakers (vpage 10)

Connecting Devices (vpage 12)

⇩

Turning the Power On (vpage 17)

Flow of operations through playback

Getting Started

Thank you for purchasing this DENON product. To ensure proper operation, please read this owner’s manual carefully before using the product. After reading them, be sure to keep them for future reference.

qOwner’s manual ......................................................................1

wGetting Started ........................................................................1

eService station list ................................................................... 1

rPower cord (Cord length: Approx. 1.6 m) ................................. 1

tRemote control (RC-1117) ........................................................1

yR6/AA batteries ....................................................................... 2

uFM indoor antenna .................................................................. 1

iAM loop antenna ..................................................................... 1

oSetup microphone

(DM-A409, Cord length: Approx. 7.6 m) ................................... 1

Check that the following parts are supplied with the product.

tr u i o

Accessories

⇩

Connecting the Speakers (vpage 11)

Playback

⇩

Playing Components (vpage 37)

Adjusting the Sound Field Effects (vpage 44)

⇩

Selecting the Surround Mode (vpage 42)

Audyssey Auto Setup (vpage 20)

Settings

Input Setup (vpage 32)

Getting Started

Manual Setup (vpage 25)

Perform “Manual Setup” as necessary.b

Cautions on Handling Cautions on Installation

• Before turning the power switch on

Check once again that all connections are correct and that there are

no problems with the connection cables.

•

Power is supplied to some of the circuitry even when the unit is set to the standby mode. When traveling or leaving home for long periods of time, be sure to unplug the power cord from the power outlet.

• About condensation

If there is a major difference in temperature between the inside of

the unit and the surroundings, condensation (dew) may form on the operating parts inside the unit, causing the unit not to operate properly.

If this happens, let the unit sit for an hour or two with the power

turned off and wait until there is little difference in temperature before using the unit.

• Cautions on using mobile phones

Using a mobile phone near this unit may result in noise. If so, move

the mobile phone away from this unit when it is in use.

• Moving the unit

Turn off the power and unplug the power cord from the power

outlet.

Next, disconnect the connection cables to other system units before

moving the unit.

•

Note that the illustrations in these instructions may differ from the actual unit for explanation purposes.

Note: For proper heat dispersal, do not install this unit in a conﬁned space, such as a bookcase or similar enclosure.

b Note

About the Remote Control Unit

In addition to the AVR-1910, the included remote control unit (RC-

1117) can also be used to operate the equipment listed below.

q DENON system components w Non-DENON system components

• By setting the preset memory (vpage 52)

ENGLISH

NOTE

• Replace the batteries with new ones if the set does not operate even when the remote control unit is operated close to the unit.

• The supplied batteries are only for verifying operation.

• When inserting the batteries, be sure to do so in the proper direction, following the “q” and “w” marks in the battery compartment.

• To prevent damage or leakage of battery ﬂuid:

• Do not use a new battery together with an old one.

Wall

• Do not use two different types of batteries.

• Do not attempt to charge dry batteries.

• Do not short-circuit, disassemble, heat or dispose of batteries in ﬂames.

• If the battery ﬂuid should leak, carefully wipe the ﬂuid off the inside of the battery compartment and insert new batteries.

• Remove the batteries from the remote control unit if it will not be in use for long periods.

• Used batteries should be disposed of in accordance with the local regulations regarding battery disposal.

Getting Started

Connections Playback Remote Control Information Troubleshooting

Operating Range of the Remote Control Unit

Point the remote control unit at the remote sensor when operating it.

Inserting the Batteries

q Lift the clasp and remove the

rear cover.

e Put the rear cover back on.

w Load the two batteries properly

as indicated by the marks in the battery compartment.

R6/AA

30°

Approx. 7 m

NOTE

The set may function improperly or the remote control unit may not operate if the remote control sensor is exposed to direct sunlight, strong artiﬁcial light from an inverter type ﬂuorescent lamp or infrared light.



SpeciﬁcationsMulti-ZoneSettings

ENGLISH

o,Q0

Q7Q6

Q0 Q1 Q2 Q3 Q4 Q5 W9 E0

w e r t y

W1W2W3W4W5W6

o,Q0

Getting Started

Part Names and Functions

Front Panel

Connections Playback Remote Control Information Troubleshooting Speciﬁcations

Multi-ZoneSettings

Buttons, terminals and displays only provided on the main unit

Q6 Power indicator ·········································· (17) Q7 Power switch (hON jOFF) ················ (17, 63) Q8 Headphones jack (PHONES) ······················ (41) Q9 V. AUX INPUT connectors ························· (16) W0 SETUP MIC jack ·········································· (21) W1 AUDYSSEY DYNAMIC VOLUME

indicator ······················································(46)

W2 HD AUDIO indicator ···································· (42)

W3 MASTER VOLUME indicator W4 Display W5 Remote control sensor ································· (3) W6 TUNING PRESET button ···························· (39) W7 SOURCE MODE SELECT button················(37) W8 FRONT SPEAKERS SELECT button ··········· (41) W9 DIMMER button ·········································· (31) E0 STATUS button ··········································· (48)

Button that function in the same way as remote control buttons

For buttons not explained here, see the page indicated in parentheses ( ).

q Power operation button

(ON/STANDBY) ·········································· (17)

w SURROUND MODE buttons ······················ (42) e MENU button ·············································· (18) r Cursor buttons (uio p) ························· (18) t ENTER button ············································· (18) y RETURN button ·········································· (18) u QUICK SELECT buttons ····························· (50)

i MASTER VOLUME control knob ··············· (37) o SOURCE SELECT knob······························· (37) Q0 ZONE2 SELECT button····························(51) Q1 ZONE2 ON/OFF button ···························(51) Q2 RESTORER button ······································ (47) Q3 DYNAMIC EQ button ·································· (46) Q4 DYNAMIC VOLUME button ······················· (46) Q5 MULTEQ button ·········································(46)

n Buttons that function in the same way as Front Panel buttons

Front Rear



i uoQ0Q1Q2Q3Q4Q5

wq e tr y

Display

q Decoder indicators

The indicator for the currently operating decoder lights.

w Input audio signal indicators e Information display

The input source name, surround mode, setting

values and other information are displayed here.

r Front speaker indicator

These light according to the settings of the front A and B speakers (vpage 41).

t QUICK SELECT indicators

These light when the Quick Select function is set (vpage 50).

y ZONE2 indicator

Lights when signals are being output to the ZONE2 (vpage 51).

u Master volume indicator

When performing setting operations, displays the menu number.

i SLEEP TIMER indicator

Lights when the sleep timer is operating (vpage 49).

o MUTE indicator

Lights when the muting mode is set (vpage

41).

Q0 AUDYSSEY indicator

These light as shown below in the different modes (vpage 46).

: During “MultEQ” , “Dynamic EQ”,

“Dynamic Volume” operation

 b When speaker settings are changed after

the Audyssey Auto Setup procedure, either the indicators’ frame turns off or all the indicators turn off.

Q1 Input mode indicators Q2 S.BACK indicator

Lights when audio signals are being output from the surround back speakers (vpage 26).

Q3 RESTORER indicator

Lights during “RESTORER” operation (vpage

47).

Q4 HDMI indicator

Lights when HDMI input signals are detected (vpage 13).

Q5 Tuner reception mode indicators

This lights according to the reception conditions when the input source is set to “TUNER”.

• RDS

This lights when receiving RDS broadcasts.

• AUTO

This lights when in the auto tuning mode.

• STEREO

In the FM mode, this lights when receiving analog stereo broadcasts.

• TUNED

This lights when the broadcast is properly tuned in.

ENGLISH

Part Names and Functions

Getting Started

Connections Playback Remote Control Information Troubleshooting

Multi-ZoneSettings

Speciﬁcations

: During “MultEQ” operation

: During “MultEQ” , “Dynamic EQ”

operation



ENGLISH

q w e r t y u i o

Q0Q1Q2Q3Q4Q5

"69 065

Getting Started

Rear Panel

Connections Playback Remote Control Information Troubleshooting Speciﬁcations

Multi-ZoneSettings

Part Names and Functions

q HDMI connectors ·······································(13) w Digital audio connectors ··························· (14) e VIDEO connectors ·····································(15) r PRE OUT connector ··································· (11)

t REMOTE CONTROL jacks

Connect a device that supports the remote

control function.

Input

ZONE2

y Analog audio connectors ·························· (14) u FM/AM antenna terminals ························ (16) i Speaker terminals ······································ (11) o AC OUTLET ················································ (17) Q0 AC inlet (AC IN) ·········································· (17)

Infrared retransmitter

Extension jack for future use. (Connect devices corresponding with room to room function to this jack.)

Infrared sensor

Q1 EXT. IN connectors ···································· (16)



Q2 ZONE2 connectors ····································(51) Q3 COMPONENT VIDEO connectors ············· (14)

Q4 Control Dock for iPod S-Video input terminal

····································································(14)

Q5 Control Dock for iPod DOCK CONTROL jack

····································································(14)

Remote Control Unit

q w

Q4 Q5

W4 W5 W6

W2 W3

ENGLISH

Part Names and Functions

Getting Started

RearFront

q Remote control signal transmitter w Indicator ····················································· (52) e Power buttons ··········································· (17) r QUICK SELECT buttons ···························· (50) t SOURCE SELECT button ·························· (37) y System buttons ········································· (52) u MENU button ············································ (18) i Cursor buttons (uio p) ························ (18) o SEARCH button ··································· (38, 40) Q0 DEVICE SELECT switches ···················· (37, 52) Q1 Master volume control buttons ··············· (37)

Operations possible by remote control

Operations on the AVR-1910

Operations on six devices other that

the AVR-1910

• Preset the remote control codes of the devices to be operated (vpage 52).

• Switch two device selector switches according to the devices to be operated.

Position of switches

Connections Playback Remote Control Information Troubleshooting

Q2 MUTING button ········································· (41) Q3 Channel level adjustment button ············ (50)

Operable devices

Multi-ZoneSettings

Q4 RETURN button ········································· (18) Q5 ENTER button ············································ (18) Q6 ZONE2 power button ································ (51) Q7 Tuner operation buttons ·························· (39) Q8 MULTEQ button ········································ (46) Q9 Number buttons (0 ~ 9, +10) ····················· (52) W0 MAIN ZONE power buttons ····················· (17) W1 INPUT MODE button ································· (34) W2 SLEEP TIMER button ································· (49) W3 VIDEO SELECT button ······························ (34) W4 RESTORER button ····································· (47) W5 FRONT HEIGHT SPEAKER ON/OFF button

···································································· (45)

W6 Surround mode buttons ··························· (42) W7 DYNAMIC VOLUME button ······················ (46) W8 DYNAMIC EQ button ································ (46)

For buttons not explained here, see the page indicated in parentheses ( ).

NOTE

Buttons on the back panel may operate when the

• back lid is pressed. The SAT TU button cannot be used.

•

ZONE2 operations (vpage 51)

Punch through setting (vpage 54)

AVR-1910 (MAIN ZONE) iPod

AVR-1910 (ZONE2)

Blu-ray disc player or DVD Player

DVD recorder or Video deck

Satellite receiver or Cable TV

CD player

Speciﬁcations



ENGLISH

Getting Started Playback Remote Control Information Troubleshooting Speciﬁ cationsMulti-ZoneSettings

Connections for all compatible audio and video signal formats are described in this owner’s manual. Please select the types of connections suited for the equipment you are connecting.

After connections are completed, certain settings must be made on the receiver. Make the settings indicated“

Set as necessary

”

for the individual items.

Select the cables according to the equipment being connected.

Important Information

Cables Used for Connections

Audio and video cables

HDMI connections

HDMI cable

Audio cables

Coaxial digital connections

Coaxial digital cable

Optical digital connections

Optical cable

Analog connections

Stereo pin-plug cable

Analog connections (monaural, for subwoofer)

Pin-plug cable

Speaker connections

Speaker cables

Video cables

Component video connections

Component video cable

S-Video connections

S-Video cable

Video connections

75 Ω/ohms pin-plug video cable

(White)

(Red)

n HDMI (vpage 12) n Monitor (TV) (vpage 13) n Playback Components

 • Blu-ray Disc player / DVD player (vpage 14)  • iPod® (vpage 14)  • CD Player (vpage 14)

n Recording Components

 • Digital Video Recorder (vpage 15)  • Video Cassette Recorder (vpage 15)

n SAT/CABLE Tuner (vpage 15) n Other Devices

 • Video Camera / Game Console (vpage 16)  • Component with Multi-channel Output connectors

(vpage 16)

 • Antenna terminals (vpage 16)

n Power Cord

Connection Flown

Turning the Power On (vpage 17)

Installing/Setting the Speakers (vpage 10)

Connecting Devices (vpage 12)

(Yellow)

(Green)

(Blue)

(Red)

Connections

NOTE

• Do not plug in the power cord until all connections have been completed.

• When making connections, also refer to the operating instructions of the other components.

• Be sure to connect the left and right channels properly (left with left, right with right).

• Do not bundle power cords together with connection cables. Doing so can result in humming or noise.

Connecting the Speakers (vpage 11)

Connecting Devices not Equipped with HDMI terminals (vpage 13)

Connections

ENGLISH

[ENT]:Select

MODE:STEREO

IN :DVD

[Auto]

Master Volume -80.0dB

Important Information

Getting Started

Converting Input video signals for Output (Video Conversion Function)

The AVR-1910 is equipped with four types of video input terminals (HDMI, Component video, S-Video and video) and three types of video output terminals (HDMI, Component video and video). Use the terminals according to the devices to be connected. This function automatically converts various formats of video signals input to the AVR-1910 into the format used to output the video signals from the AVR-1910 to a monitor.

Video devices

Output

HDMI connector

Component video

connectors

S-Video connector

Input

(IN)

HDMI connector

Component video

connectors

S-Video

connector

AVR-1910

Output

(MONITOR OUT)

HDMI

connector

Component video

connectors

Monitor (TV)

Input

HDMI connector

Component video

connectors

How the on-screen display is displayed depending on the video input signal

The way the on-screen display of the menus, status, etc., is displayed differs according to the type of video signal input to the AVR-1910.

When video signals are input from the HDMI or component video terminals

Menu: Switches to a screen with a black background and the menu is superimposed. (b1)

•

Status display: Not displayed.

•

b1: If you want to display the menus superimposed on the picture being played, input the same video

signals to the video terminals. When a menu is displayed, the picture switches to the one being input from the video terminals and the menu is displayed superimposed over this picture.

NOTE

Menus and status display screens are not displayed for component video terminal pictures. To display them, also connect the video terminals.

When video signals are being input from the S-Video or video terminals

Menu: Menus are displayed superimposed over the picture being played.

•

Status display: Displayed.

•

Examples of on-screen display

Menu screen• Status display screen•

When the input source is switched

When the volume is adjusted

Connections

Playback Remote Control Information Troubleshooting

Multi-ZoneSettings

Video connector

• The video conversion function supports the NTSC, PAL, SECAM, NTSC 4.43, PAL-N, PAL-M and PAL-60 formats.

• The resolution of the video signal input to the AVR-1910’s HDMI terminal is the resolution set at “Resolution” (vpage 34). (1080p HDMI signals and 1080p component signals are output at 1080p, regardless of the setting.)

• Resolutions of HDMI-compatible TVs can be checked at “HDMI Information” (vpage 48).

NOTE

• The S-Video input terminal is exclusively for use with a Control Dock for iPod. It can be used when the Control Dock for iPod is connected to the terminal assigned to the iPod input source.

• HDMI signals cannot be converted into analog signals.

• When a non-standard video signal from a game machine or some other source is input, the video conversion function might not operate.

Video connector

Status display: The operating status is displayed temporarily on the

screen when the input source is switched or the volume is adjusted.

Speciﬁcations



ENGLISH

Getting Started Playback Remote Control Information Troubleshooting SpeciﬁcationsMulti-ZoneSettings

Installing/Setting the Speakers

• The AVR-1910 is compatible with various types of surround playback.

Connections

• Decide on the surround modes to be played on the AVR-1910 before making connections and settings.

a Determine the Speaker Layout.

Below we introduce examples of speaker layouts. Refer to these to arrange your speakers according to their type and how you want to use them.

Installing All the Speakers

Front Height speakers

Subwoofer

Surround

speaker

Surround back speakers

NOTE

It is not possible to use the front height speakers and surround back speakers simultaneously.

Front speakers

Center speaker

Surround

speaker

When 7.1ch (Surround Back Speaker) Connectedn

Front speakers

Center speaker

Monitor

z1: 22 ~ 30˚ z2: 90˚

z4: 30˚ z5: 45˚

When 5.1ch Connectedn

Front speakers Center speaker

Monitor

z1: 22 ~ 30˚ z2: 120˚

z3: 110˚

Subwoofer

Surround speakers

Surround back

speakers

As seen from above

Surround

speaker

Front speaker

As seen from the side

Surround back speaker

60 to 90 cm

Point slightly

downwards

When 6.1ch Connectedn

Front speakers

Center speaker

Monitor

Subwoofer

Surround speakers

Surround back

As seen from above

speaker

H G

z1: 22 ~ 30˚ z2: 90˚ z3: 110˚

Surround

speaker

Front speaker

60 to 90 cm

As seen from the side

Surround back speaker

Point slightly

downwards

Subwoofer

Surround

speaker

60 to 90 cm

As seen from the side

Surround speakers

As seen from above

Front speaker

H G

When 7.1ch (Front Height Speaker) Connectedn

Front height speakers

Front speakers

Center speaker

Subwoofer

As seen from above

Monitor

Surround speakers

z1: 30˚ z2: 45˚

Point slightly

downwards

Front speaker

z3: 90˚ z4: 110˚

Front height speaker

60 to 90 cm

As seen from the side

Surround speaker

0

w q

w q w q

(L) (R)

w qw q

(R) (L)

w qw q

(R) (L)

Installing/Setting the Speakers

Set the “Amp Assign” Mode According to the Speaker Layout.

The signals output from the AVR-1910’s SURR. BACK/AMP ASSIGN speaker terminals can be switched to signals of the surround mode being used (vpage 25 “Amp Assign”).

Amp assign mode

(vpage 25)

SURR. BACK/AMP ASSIGN

Speaker connections

Example of speaker installation

Connecting the Speakers

Subwoofer with builtin ampliﬁer

Front speakers

ENGLISH

Getting Started

Center

speaker

Surround speakers

Connections

Normal

Front Height

Front A Bi-Amp

Front B Bi-Amp

ZONE2

b Connect to the “L” speaker

b Set “S.Back” (vpage 26) to

b For connections, see “About

(Default)

Surround back

speakers

Surround back

speakers

terminal.

“1sp”.

Not connected

Set the “S.Back” setting (vpage 26) to “None”.

Front Height

speakers

Front A or B

speakers

bi-amp connections”(vpage

12).

ZONE2 speakers

(7.1)

(6.1)

(5.1)

MAIN ZONE ZONE2

(7.1)

(5.1)



(5.1)

(2)

Protection circuit

If the core wires touch the rear panel and the screws etc., or the ± sides touch each other, the protection circuit will be activated and the power indicator will ﬂash red at intervals of 0.5 secs. If the protection circuit is activated, the speaker output is isolated, and the power supply goes to the standby state. If the power supply is turned off, after the power supply cord is withdrawn, please conﬁrm that speaker cable and input cable are connected. Also, if replaying large sound levels by using a speaker having an impedance less than that

For connections of the SURR. BACK/AMP ASSIGN speaker terminals, see “Amp Assign” (vpage 25).

speciﬁed (eg, 4 Ω/ohms), the temperature will rise, and the protection circuit might be activated. The power supply will go into the standby state, and the power indicator will ﬂash red at 2 second intervals. In this case, please switch off the power supply, and wait until the AVR-1910 has cooled down, and the surrounding ventilation is good. Even if there are no problems with the surrounding ventilation and connections, in the event of the protection circuit becoming activated, due to thinking that the AVR-1910 has failed, please contact DENON Service center after switching off.

Playback Remote Control Information Troubleshooting

Multi-ZoneSettings

Speciﬁcations



ENGLISH

wq wq

(R) (L)

Getting Started Playback Remote Control Information Troubleshooting SpeciﬁcationsMulti-ZoneSettings

Connecting the Speaker Cables

Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being connected to the AVR-1910, and be sure to interconnect the channels and polarities correctly.

Connections

Peel off about 10 mm of sheathing from the tip

of the speaker cable, then either twist the core wire tightly or terminate it.

Turn the speaker terminal counterclockwise

to loosen it.

Insert the speaker cable’s core wire to the hilt

into the speaker terminal.

 Turn the speaker terminal clockwise to tighten

it.

Use speakers with an impedance of 6 to 16 Ω/ohms. When using front A and B speakers simultaneously, use speakers with an impedance of 12 to 16 Ω/ohms.

NOTE

• Connect the speaker cables in such a way that they do not stick out of the speaker terminals. The protection circuit may be activated if the core wires touch the rear panel or if the + and – sides touch each other (v “Protection circuit”).

• Never touch the speaker terminals while the power supply is connected. Doing so could result in electric shock.

Connecting the Speakers

About bi-amp connections

These connections make for higher quality playback sound with no interference between the signals of the bass and treble units. When the ampliﬁer assignment mode is set to “Front A Bi-Amp” or “Front B Bi-Amp”, connect as shown below. (The illustration shows a connection example for the front B Bi-Amp speakers.)

Front speakers B

AVR-1910

When in the “Front A Bi-Amp” and “Front B Bi-Amp” modes, the same signals are output from the front speaker terminals and the AMP ASSIGN terminals.

NOTE

• Use speakers compatible with bi-amp connections.

• When making bi-amp connections, be sure to remove the shortcircuiting plate or wire between the speaker’s woofer and tweeter terminals.

Connecting Devices

Connecting Devices Equipped with HDMI terminals

Important Information

n About HDMI

“HDMI” is the abbreviation of “High Deﬁnition Multimedia Interface”. This interface allows transfer of digital video signals

and digital audio signals over a single HDMI cable.

“HDMI”, “HDMI logo” and “High-Deﬁnition Multimedia Interface”

are trademarks or registered trademarks of HDMI Licensing LLC.

n Functions usable with HDMI connections

Deep Color

Eliminates on-screen color banding, for smooth tonal transitions and subtle gradations between colors.

x.v.Color

Enables displays with natural, vivid colors. “x.v.Color” is a Sony registered trademark.

Auto Lip Sync (vpage 28)

HDMI 1.3 incorporates an automatic video/audio synching capability that allows devices to perform this synchronization automatically with total accuracy.

HDMI control function (vpage 28, 49)

This function allows you to operate external devices from the receiver and operate the receiver from external devices.

NOTE

These functions will not work if the device connected to the HDMI terminal does not support Deep Color or x.v.Color signal transfer or the Auto Lip Sync function.

n Copyright protection system (HDCP)

The AVR-1910 supports HDCP (High-bandwidth Digital Contents Protection). HDCP is a copyright protection technology for digital video signals. The devices connected to the AVR-1910 must also support HDCP.

NOTE

When a device that does not support HDCP is connected, video signals are not properly output.

2

7*%&0

$0.10/&/57*%&0

: 1# 13

7*%&0

065

)%.*

065

)%.*

065

)%.*

065

)%.*

Connections

The AVR-1910 allows connection of inputs from up to 4 HDMI devices and output to 1 TV.

DVD

Player

Blu-ray

Disc Player

SAT/CABLE

Tuner

Connecting devices

n Connecting to a device equipped with a DVI-D

terminal

When an HDMI/DVI conversion cable (sold separately) is used, the HDMI video signals are converted to DVI signals, allowing connection to a device equipped with a DVI-D terminal.

NOTE

• No sound is output when connected to a device equipped with a DVI-D terminal. Also make the audio connections.

• Signals cannot be output to DVI-D devices that do not support HDCP.

• Depending on the combination of devices, the video signals may not be output.

ENGLISH

Getting Started

Connecting Devices not Equipped with HDMI terminals

Monitor (TV)

Connections

• Select the terminal to use and connect the device.

• For video connections, see “Converting input video signals for output (Video Conversion Function)” (vpage 9).

For instructions on HDMI connections, see “Connecting Devices Equipped with HDMI terminals” on page 12.

Monitor (TV)

Playback Remote Control Information Troubleshooting

Digital Video

Recorder

Monitor

(TV)

• Use a cable on which the HDMI logo is indicated (a certiﬁed HDMI product) for connection to the HDMI connector. Normal playback may not be possible when using a cable other than one on which the HDMI logo is indicated (a non-HDMI-certiﬁed product).

• When the AVR-1910 is connected to other devices with HDMI cables, also connect the AVR-1910 and TV using an HDMI cable.

• When a device supporting Deep Color signal transfer is connected, use a cable compatible with HDMI ver.1.3a.

• Video signals are not output if the input video signals do not match the monitor’s resolution. In this case, switch the Blu-ray Disc player / DVD player’s resolution to a resolution with which the monitor is compatible.

NOTE

• If the menu “HDMI Audio Out” setting (vpage 28) is set to “AMP”, the sound may be interrupted when the monitor’s power is turned off.

• The audio signal from the HDMI output terminal (sampling frequency, number of channels, etc.) may be limited by the HDMI audio speciﬁcations of the connected device regarding permissible inputs.

n Settings related to HDMI connections

Set as necessary. For details, see the respective reference pages.

Input terminal assignment (vpage 33)

Set this when changing the input sources of the different terminals.

HDMI Setup (vpage 28)

Make these settings related to HDMI input/output signals.

• Auto Lip Sync

• HDMI Audio Out

• HDMI Control

• Standby Source

• Power Off Control

NOTE

The audio signals output from the HDMI connectors are only the HDMI input signals.

SpeciﬁcationsMulti-ZoneSettings

The component video connectors may be indicated differently on your monitor. For details, see the monitor’s operating instructions.



ENGLISH

"6%*0

065

7*%&0

$0.10/&/57*%&0

: 1# 13

065

"6%*0

065

$0"9*"-

ASD-3Nまたは ASD-3W

Getting Started Playback Remote Control Information Troubleshooting SpeciﬁcationsMulti-ZoneSettings

Playback Components

Blu-ray Disc player / DVD player

Connections

Select the terminal to use and connect the device.

For instructions on HDMI connections, see “Connecting Devices

Equipped with HDMI terminals” on page 12.

Control dock for iPod

Use a DENON control dock for iPod (ASD-1R, ASD-11R, ASD-3N or ASD-3W sold separately) to connect the iPod to the AVR-1910. For instructions on the control dock for iPod settings, refer to the control dock for iPod’s operating instructions.

Connecting Devices not Equipped with HDMI terminals

CD Player

Blu-ray Disc player / DVD player

Control dock for iPod

ASD-3N or ASD-3W

Set as necessary

Set this to change the input signal to which the input source is assigned. “Assign” (vpage 33)

Set as necessary

Set this to change the input signal to which the input source is assigned.

“Assign” (vpage 33)

NOTE

When connected to a Blu-ray Disc player, and playing Dolby TrueHD, DTS-HD, Dolby Digital Plus, connect the HDMI.



Set as necessary

Set this to assign the iPod to a terminal other than “VCR (iPod)”. “iPod Dock” (vpage 33)

With the default settings, the iPod can be used connected to the VCR (iPod) connector.

ENGLISH

065

"6%*0 7*%&0

7*%&0"6%*0

065 065

$0"9*"-

3- 3-

065

"6%*0"6%*0 7*%&07*%&0

065 */

015*$"-015*$"-

"6%*0"6%*0

065

7*%&0 7*%&0

$0.10/&/57*%&0

: 1# 13

065

065065

"6%*0"6%*0 7*%&0

"6%*0

7*%&0

Connecting Devices not Equipped with HDMI terminals

Getting Started

Recording Components

Digital Video Recorder

Select the terminal to use and connect the device.

For instructions on HDMI connections, see “Connecting Devices

Equipped with HDMI terminals” on page 12.

Digital Video Recorder

SAT/CABLE Tuner

Video Cassette Recorder

Select the terminal to use and connect the device.

For instructions on HDMI connections, see “Connecting Devices Equipped with HDMI terminals” on page 12.

Video cassette recorder

Select the terminal to use and connect the device.

For instructions on HDMI connections, see “Connecting Devices Equipped with HDMI terminals” on page 12.

SAT/CABLE Tuner

Connections

Playback Remote Control Information Troubleshooting

Set as necessary

Set this to change the input signal to which the input source is assigned.

“Assign” (vpage 33)

NOTE

• To record video signals through the AVR-1910, use the same type of video cable for connection between the AVR-1910 and the player as the cable used for connection between the AVR-1910 and the recorder.

• Do not connect the output of the component connected to the AVR-1910’s OPTICAL2 output connector to any input connector other than OPTICAL2.

• Digital signals are not output from the analog REC OUT connector.

Set as necessary

Set this to change the input signal to which the input source is assigned.

“Assign” (vpage 33)

NOTE

• To record video signals through the AVR-1910, use the same type of video cable for connection between the AVR-1910 and the player as the cable used for connection between the AVR1910 and the recorder.

• Digital signals are not output from the analog REC OUT connector.

Set as necessary

Set this to change the input signal to which the input source is assigned.

“Assign” (vpage 33)



SpeciﬁcationsMulti-ZoneSettings

ENGLISH

065

"6%*07*%&0

7*%&0 "6%*0

065

46#

800'&3

$&/5&3 463306/%

#"$,

463306/%

'30/5

"6%*0

Getting Started Playback Remote Control Information Troubleshooting SpeciﬁcationsMulti-ZoneSettings

Other Devices

Connecting Devices not Equipped with HDMI terminals

Video Camera / Game Console

Connections

Video camera / Game console

Component with Multi-channel Output connectors

The video signal can be connected in the same way as a Blu-ray Disc player / DVD player (vpage 14).

Blu-ray Disc player / DVD player / External decoder

Antenna terminals

Direction of broadcasting station

FM antenna

75 Ω/ohms Coaxial cable

FM indoor antenna

(supplied)

Black

AM outdoor antenna

Ground

White

AM loop antenna (supplied)

n AM loop antenna assembly

Remove the vinyl tie and take out the

connection line.

Bend in the reverse direction.



Set as necessary

To play analog signals input from the external input (EXT. IN) terminal, set “Input Mode” (vpage 34) on the menu to “EXT. IN”. “EXT. IN” can also be selected with .

With the antenna on top of any

-1

stable surface.

Mount

 With the antenna attached to a

-2

wall.

Installation hole Mount on wall, etc.

n Connection of AM antennas

Push the lever.

Insert the conductor.

Connecting Devices not Equipped with HDMI terminals

Connecting the Power Cord

Wait until all connections have been completed before connecting the power cord.

To household

Power cord

power outlet

(AC 230 V, 50 Hz)

Once Connections are Completed

Turning the Power On

Press .

The power indicator lights red and the

power is set to the standby mode.

ENGLISH

Getting Started

Connections

Return the lever.

NOTE

• Do not connect two FM antennas simultaneously.

• Even if an external AM antenna is used, do not disconnect the AM loop antenna.

• Make sure the AM loop antenna lead terminals do not touch metal parts of the panel.

Connection to the AC outlets

• These outlets supply power to external audio equipment.

• Audio equipment with a total power consumption of 100 W (0.43 A) can be connected.

• The power supply turns on and off together with on the main unit. When set to “ON”, power is supplied from the outlet. When set to “STANDBY”, no power is supplied.

NOTE

When “HDMI Control” (vpage 28) is set to “ON”, power is supplied constantly to the AC outlet (UNSWITCHED).

NOTE

• Insert the AC plugs securely. Incomplete connections could cause noise.

• Only use the AC outlet to plug in audio equipment. Do not use them as power supplies for hairdryers or anything other than audio equipment.

Press .

The power indicator ﬂashes green and the

power turns on.

b Also press when in standby

mode, the power turns on.

 When has been pressed, the input source set with the

is set. If a has been pressed, the input source stored in the memory for the quick select function is set (vpage 50 “Saving frequently used settings (Quick Select Function)”).

This operation can also be performed by pressing a on the main unit.

Front

Turning the Power Off

Press .

The power is set to the standby mode.

Press .

The power indicator turns off, and so does

the power.

NOTE

• Power continues to be supplied to some of the circuitry even when the power is in the standby mode. When leaving home for long periods of time or when traveling, either press to turn off the power, or unplug the power cord from the power outlet.

• When the ZONE2 power is switched on, and you want to switch off the MAIN ZONE power, press .

Front

Playback Remote Control Information Troubleshooting

SpeciﬁcationsMulti-ZoneSettings



ENGLISH

1.Parameter

2.Information

3.Auto Setup

4.Manual Setup

5.Input Setup

[ENT]:Select

Getting Started Connections Playback Remote Control Information Troubleshooting SpeciﬁcationsMulti-Zone

Settings

With the AVR-1910, settings and operations for most functions can be performed by operating while looking at the menus displayed on the monitor screen.

Menu map

Settings

nOperations

Press .

The menu is displayed.

Press ui to

select the item you want to

⇩

set, then press

Press ui to

select the item you want to

⇩

set, then press

Use uiop to select the item,

then press to set.

b To return to the previous item, press .

⇩

b Select “Default Yes”, then press

reset to the default setting.

Press .

⇩

The settings made up to that point are entered and the settings menu screen turns off.

Setting menusn

Items that only need to be set once

Set these for example upon purchase. Once these items are set, there is no need to set them again unless the speaker layout or the connected speakers have been changed.

Front

Setting items Number Detailed items Description Page

1. Parameter

Adjust various audio parameters.

2. Information

Show information about receiver settings, input signals, etc.

3. Auto Setup

Makes the optimum speaker settings and corrects for the acoustic characteristics of the room.

4. Manual Setup

Use this to make various types of detailed settings.

5. Input Setup

Use this to make settings related to playing input sources.

1-1 Surround Parameter Adjust surround sound parameters. 44 1-2 Tone Control Adjusts the treble and bass tone. 45 1-3 Audyssey Settings Makes the MultEQ, Dynamic EQ and Dynamic Volume settings. 46 1-4 Manual EQ Adjust tonal quality for each speaker using graphic equalizer. 47 1-5 RESTORER 1-6 Audio Delay Compensate for incorrect timing between video and audio. 47 2-1 Status Shows information about current settings. 48 2-2 Audio Input Signal Shows information about audio input signals. 48 2-3 HDMI Information Displays the HDMI input/output signals and TV information. 48

2-4 Auto Surround Mode Displays the settings stored for the auto surround mode. 48 2-5 Quick Select Displays the settings stored for the Quick Select function. 48 2-6 Preset Channel Shows information about preset channels. 48 3-1 Audyssey Auto Setup Makes the optimum settings for the speakers being used

3-2 Parameter Check Check Audyssey Auto Setup measurement results.

4-1 Speaker Setup Sets the speaker size and distance, the channel level, etc. 25 4-2 HDMI Setup Make settings for HDMI video/audio output. 28 4-3 Audio Setup Make settings for audio playback. 29 4-4 ZONE2 Setup Make settings for audio playback in a ZONE2 system. 30 4-5 Option Setup Make various other settings. 30 5-1 Assign Change input connector assignment. 33 5-2 Video Makes the video settings. 34 5-3 Input Mode Sets the audio input mode and decode mode. 34 5-4 Rename Change the display name for this source. 35 5-5 Source Level Adjust the playback level of the audio input. 35 5-6 iPod Playback Mode Make settings for iPod playback. 35 5-1 Auto Preset Use the auto preset function to program radio stations. 36 5-2 Preset Skip 5-3 Preset Name Assign name to a preset memory. 36

Uncompress compressed sources and apply bass boost for richer sound.

automatically.

This item is only displayed after the Audyssey Auto Setup procedure has been performed.

Set the preset memories that you do not want to display when tuning.

8

Examples of On-screen Display and Front Display

1.Parameter

2.Information

3.Auto Setup

4.Manual Setup

5.Input Setup

[ENT]:Select

P a ra m e t e r

5-1-1.Input Assign

HDMI Digi Comp

DVD 1 C1 1

HDP 2 TV 01 SAT/CBL 3 C2 VCR/iPod DVR 4 02 2

[ENT]:Select [RTN]:Back

D V D [ H D M I 1 ]

5-1-1.Input Assign

HDMI Digi Comp

DVD 1 C1 1

HDP 2 TV 01 SAT/CBL 3 C2 VCR/iPod DVR 4 02 2

[ENT]:Select [RTN]:Back

D V D • H D M I 1 –

Default

[SRCH]:Caps. [ENT]:OK [RTN]:Cancel

DVD DVD

5-4.Rename

D V D • ¡ D V D –

[ ]:Up/Down [ENT]:Select [RTN]:Back

Default

DVD [ DVD ]

5-4.Rename

D e fa u l t

D ef a u l t ? : • N o

Below we describe typical examples of displays on the TV screen and on the set’s display window.

ENGLISH

Getting Started

On-screen Display Front Display Description

n Top menu display

n Display when changing settings

n Display when inputting characters

Press . Press .

⇩ ⇩

: The menu items are displayed here.

: The selected line is displayed here. The currently selected item is displayed on the display.  Use ui to move to the item you want to set.

: The number of the current selected setting menu is

displayed.

: The number of the current selected setting menu is

displayed.

w e

q w

uio p

: Use

: Press to set to the mode in which the setting can be

made.

: 0 1 is displayed at the sides of items whose setting can be

changed. Use op to change to the desired setting.

: When op is pressed, the cursor moves to the left or right.

: When ui is pressed at the position at which you want to

input the character, the character is input.

: The number of the current selected setting menu is

displayed.

to move to the item you want to set.

Connections Playback Remote Control Information Troubleshooting

Settings

SpeciﬁcationsMulti-Zone

n Display when resetting

: Press i to select “Default”, then press to set.

: The number of the current selected setting menu is

displayed.



ENGLISH

Getting Started Playback Remote Control Information Troubleshooting Speciﬁ cationsMulti-Zone

Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)

The acoustic characteristics of the connected speakers and listening room are measured and the optimum settings are made automatically.

NOTE

• Loud test sounds may be played during Audyssey MultEQ automatic speaker setup. This is part of normal operation. If there is background noise in room, these test signals will increase in volume.

• Do not stand between the speakers and setup microphone or allow obstacles in the path while the measurements are being made. This will cause inaccurate readings.

• Make the room as quiet as possible. Background noise can disrupt the room measurements. Close windows, silence cell phones, televisions, radios, air conditioners, ﬂ uorescent lights, home appliances, light dimmers, or other devices as measurements may be affected by these sounds.

Cell phones should be placed away from all audio electronics during

the measurement process as Radio Frequency Interference (RFI) may cause measurement disruptions (even if the cell phone is not in use).

Audyssey MultEQ® automatically measures the acoustical problems in the listening environment to create the best audio experience for your home theater.

• When the Audyssey Auto Setup procedure is performed, the MultEQ, Dynamic EQ and Dynamic Volume functions (vpage 46) are enabled.

• Use the included setup microphone (DM-A409) to perform the Audyssey Auto Setup procedure.

• Measurements are performed by placing the calibrated microphone successively at multiple positions throughout the listening area as shown in GExample qH. For best results, it is strongly recommended to measure 6 positions so that the measurements have the proper spatial weighting.

Even if the listening environment is small as shown in GExample wH,

measuring at multiple points throughout the listening environment results in more effective correction.

n When using Front Height Speakers

 GExample qH GExample wH

FHL FL SW C FR FHR

SL SR

FHL FL SW C FR FHR

SL SR

n When using Surround Back Speakers

 GExample qH GExample wH

FL SW C FR

SL SR

SBRSBL



FL SW C FR

SL SR

SBRSBL

( : Measuring positions)

Important Information

About the main listening position (*M)

The main listening position refers to the most central position where one would normally sit within the listening environment. MultEQ uses the measurements from this position to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer.

FHL : Front height speaker (L) FL : Front speaker (L) SW : Subwoofer C : Center speaker FR : Front speaker (R) FHR : Front height speaker (R) SR : Surround speaker (R) SBR : Surround back speaker (R) SBL : Surround back speaker (L) SL : Surround speaker (L)

( : Measuring positions)

n Check Audyssey Auto Setup Measurement

Results (Parameter Check) (vpage 24)

Audyssey Auto Setup Flown

Step 1 :Connect the included Setup Microphone (vpage 21)

Step 3 : Performing the Audyssey Auto Setup Procedure (vpage 22)

Step 2 :Audyssey Auto Setup Preparations

(vpage 21)

n Setting the speakers for playing the front channel

(Front Sp.) (vpage 21)

n Changing the ampliﬁ er assignment (Amp Assign)

(vpage 22)

Connections Settings

ENGLISH

3-1.Audyssey Auto Setup MultEQ

at ear height at

Front Sp.: A

Normal

Amp Assign:

Start Cancel [ENT]:Select [RTN]:Back

Please place microphone

main listening position.

Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)

Getting Started

Step 1 : Connect the included Setup Microphone

NOTE

• Do not disconnect the setup microphone until the Audyssey Auto Setup procedure is completed.

• When using headphones, unplug the headphones before starting the Audyssey Auto Setup procedure.

Check the speaker connections.

(vpage 11 “Connecting the Speakers”)

Turn on the power of the TV and subwoofer.

Set the TV’s input to the AVR-1910.

Turn on the AVR-1910’s power.

(vpage 17 “Turning the Power On”)

Connect the included calibrated setup microphone to

the SETUP MIC jack on the main unit.

The Audyssey Auto Setup screen appears automatically.

Sound

receptor

Mount the setup microphone on a tripod or stand and

install it at the main listening position.

When installing the setup microphone, adjust its height so that

the section where the sound is received is at the height of the ears during listening.

• Do not hold the microphone in your hand during measurements.

• Avoid placing the microphone close to a seat back or wall as sound

When using a subwoofer on which the volume can be adjusted and the crossover frequency can be set

When using a subwoofer, make the following settings before starting the Audyssey Auto Setup procedure:

n When using a subwoofer with a direct mode

n When using a subwoofer without a direct mode

• Volume :“12 o’clock position”

• Crossover frequency :“Maximum/Highest Frequency”

• Low pass ﬁlter :“Off”

• Standby mode :“Off”

NOTE

reﬂections may give inaccurate results.

Set the direct mode to “On” and disable the volume adjustment

and crossover frequency setting.

Make the following settings:

Step 2 : Audyssey Auto Setup Preparations

around items indicate the settings made upon purchase.

If adjustment to the environment is necessary, set the following items before proceeding.

Setting the speakers for playing the front channel (Front Sp.)

The front speaker to be measured can be selected ahead of time here.

 Press ui to select “Front Sp.”.

Front

Use op to select the speakers.

: The sound is output from front speakers A when measuring

the front speakers.

: The sound is output from front speakers B when measuring

the front speakers.

A + B

: The sound is output simultaneously from front speakers A

and B when measuring the front speakers.

n To cancel Audyssey Auto Setup

 Use ui to select “Cancel”, then use o p to select “Yes”.

Connections Playback Remote Control Information Troubleshooting

Settings

SpeciﬁcationsMulti-Zone

microphone

Setup

2

ENGLISH

Step2:Measurement MultEQ

Retry Cancel

[ENT]:Cancel

Calculate

All the measurements were finished.

Step3:Calculating

MultEQ

Calculating

[----------]

Please wait...

Step4:Check MultEQ

Please check the results of the measured item.

Distance Check Channel Level Check Crossover Freq.Check

Speaker Config.Check

Next [ENT]:Select

3-1.Audyssey Auto Setup MultEQ

at ear height at

Front Sp.: A

Normal

Amp Assign:

Start

Cancel [ENT]:Select [RTN]:Back

Please place microphone

main listening position.

Retry [ENT]:Next

Front Sp. :Yes Center Sp. :Yes Subwoofer :Yes Surround Sp. :Yes S.Back Sp. :Yes :2sp

Step1:Speaker Detection MultEQ

Step2:Measurement MultEQ

Please place microphone

Cancel

[ENT]:Next

Calculate

2nd listening position.

at ear height at

3-1.Audyssey Auto Setup MultEQ

at ear height at

Front Sp.: A

Normal

Amp Assign:

Start Cancel [ENT]:Select [RTN]:Back

Please place microphone

main listening position.

Getting Started Connections Playback Remote Control Information Troubleshooting SpeciﬁcationsMulti-Zone

Changing the ampliﬁer assignment (Amp Assign)

The signals output from the AVR-1910’s SURR. BACK/AMP ASSIGN speaker terminals can be switched to signals of the surround mode being used.

 Press ui to select “Amp Assign”.



Settings

Press o p to select

Amp Assign Mode.

Normal

ZONE2

Front A Bi-Amp

Front B Bi-Amp

Front Height

: The sound of the surround back channel is output

from the speakers connected to the SURR. BACK/AMP ASSIGN terminals.

: If the ZONE2 power is on, the sound of the

ZONE2 channel is output from the speakers connected to the SURR. BACK/AMP ASSIGN terminals.

: The sound of the front A bi-amp channel is output

from the speakers connected to the SURR. BACK/AMP ASSIGN terminals.

:  The sound of the front B bi-amp channel is output

from the speakers connected to the SURR. BACK/AMP ASSIGN terminals.

: The sound of the front height channel is output

from the speakers connected to the SURR. BACK/AMP ASSIGN terminals.

n To cancel Audyssey Auto Setup

 Use ui to select “Cancel”, then use o p to select “Yes”.

Front

Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)

Step 3 : Performing the Audyssey Auto Setup Procedure

• The Audyssey Auto Setup function detects the presence of each speaker and automatically calculates the speaker size, channel level, distance, and optimal crossover frequency setting. Audyssey MultEQ corrects acoustical distortions within the listening area.

• Once started, MultEQ will play a series of test tones through each speaker.

• Before starting, connect and position all of your speakers.

 Press ui to select

“Start”, then press

Detection of the speaker

conﬁguration starts.



Once all the speakers

have been detected and the screen on the right appears, check the results of detection of the connected speakers.

Once you have checked the results, use ui to select

“Next”, then press .

Measurements for the main listening position begin.



Once the screen on

the right appears, move the setup microphone to the second position, use

ui to select “Next”,

then press .

Measurements for the second position begin.

 Perform Step 4 repeatedly for the 3rd, 4th, 5th, and

6th measurments.

Once measurements for the sixth position are completed, “All

the measurements were ﬁnished.” is displayed.

b Measure at a total of six positions, including the main listening

position and positions around it. It is possible to stop the settings with ﬁve positions or fewer, but for better results we recommend measuring at six positions.

Once measurements

are nished, use ui to select “Calculate”, then press .

Analysis begins.

b Analysis takes several

minutes to complete. The time required for this analysis depends on the number of speakers connected. The greater the number of speakers connected, the longer analysis will take.

Use ui to select the item you want to check, then

press .

The measurement result

conﬁrmation screen is displayed.

b Subwoofers or other

speakers may be set to a value that does not correspond to the actual distance.

⇩

ENGLISH

Step5:Store MultEQ

Store

Cancel

[ENT]:Store

Please select “Store” to store measurement values.

Step5:Store MultEQ

Storing

Please wait...

Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)

Getting Started



Press .

This returns you to analysis results items, so repeat

step 7.

 Press i to select “Next”, then

press .

Front

Press ui to select

“Store”, then press

 “Storing Please wait...” is

displayed on the on-screen display while the results are being stored.

When storing is complete,

“Storing complete. Auto Setup is now ﬁnished.” is displayed on the on-screen display.

b If you do not want to save

the measurement results, use ui to select “Cancel”, then select “Yes” using

o p. All the measured

Audyssey Auto Setup data will be erased.

NOTE

Do not turn the power off while the settings are being stored.

⇩

NOTE

Do not change the speaker connections or subwoofer volume, or speaker locations after making measurements. If changes are necessary, make the changes and use the Audyssey Auto Setup once again for an updated EQ solution.

• If the result differs from the actual connection status or an error message appears, use ui to on-screen display “Retry” and then

press to repeat the measurement.

• If the result still differs from the actual connection status after remeasurement or the error message still appears, it is possible that the speakers are not connected properly. Turn the AVR-1910 off, check the speaker connections and repeat the measurement process from the beginning.

• For instance, If the location or direction of a speaker is altered, the Audyssey Auto Setup should be performed again to ensure the correct EQ solution for the new room conﬁguration.

Connections Playback Remote Control Information Troubleshooting

Settings

Disconnect the setup microphone from the AVR-

1910.

SpeciﬁcationsMulti-Zone

2

ENGLISH

3-2.Parameter Check

Speaker Config.Check

Distance Chenck Channel Level Check Crossover Freq.Check

Restore

EQ Check

[ENT]:Select [RTN]:Back

Retry Cancel

[ENT]:Retry

Microphone:None

Speaker :None

Caution MultEQ

too high or

Retry Cancel

[ENT]:Retry

Ambient noise is

Level is too low.

Caution MultEQ

Retry

R :None

Cancel Skip

Front

Caution

[ ]:Up/Down [ ]:CH

MultEQ

Retry

L :Phase

Cancel Skip

Front

Caution

[ ]:Up/Down [ ]:CH

MultEQ

Getting Started Connections Playback Remote Control Information Troubleshooting SpeciﬁcationsMulti-Zone

Error Messages

If the Audyssey Auto Setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the Audyssey Auto Setup procedure over again.

NOTE

Settings

Be sure to turn the power off before checking the speaker connections.

Error messages (examples) Cause Measures

• Included setup microphone is not connected.

• Not all speakers could be detected.

• The front L speaker was not properly detected.

• Connect the included setup microphone to the SETUP MIC jack on the main unit.

• Check the speaker connections.

Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)

Check Audyssey Auto Setup Measurement Results (Parameter Check)

This is displayed after the Audyssey Auto Setup procedure is completed.

 Press ui to select

“Parameter Check”, then press .

“Parameter Check” is

displayed on the on-screen display.

Front

• Too much noise in the room for accurate measurements to be made.

• Speaker or subwoofer sound is too low for accurate measurements to be made.

• Displayed speaker could not be detected.

· The front R speaker were not properly detected.

· Only one channel of the surround speakers was detected.

· Sound was output from the R channel when only one surround back speaker was connected.

· The surround back, but the surround speaker was not detected.

• Displayed speaker connected with the polarities reversed.

n To perform the Audyssey Auto Setup procedure again

Press ui to select “Retry”, then press .

• Either turn off any device generating noise or move it away.

• Try again when the surroundings are quieter.

• Check the speaker installation and the direction in which the speakers are facing.

• Adjust the subwoofer’s volume.

• Check the connections of the displayed speaker.

• Check the polarities of the displayed speaker.

• For some speakers, this error message may be displayed even if the speaker is properly connected. If you are sure that the wiring is

correct, press ui to select “Skip”, then press



Use ui to select the item you want to check, then

press .

Speaker Conﬁg. Check

Distance Check

Channel Level Check

Crossover Freq. Check

EQ Check



Use o p to switch the display between the different

speakers.



Press .

The conﬁrmation screen reappears. Repeat steps 2 and 3.

Even if the settings are changed after the Audyssey Auto Setup procedure, the Audyssey Auto Setup settings can be restored by selecting “Restore” then pressing .

: Check the speaker conﬁguration

: Check the distance

: Check the channel level

: Check the crossover frequency

: Check the equalizer

n To cancel Audyssey Auto Setup

Use ui to select “Cancel”, then select “Yes” using o p.

2

2

Getting Started

Connections Playback Remote Control Information Troubleshooting

Speciﬁ cations

ENGLISH

Multi-Zone

Making detailed settings (Manual Setup)

Setting items Setting contents

Amp Assign

Sets the signal output to the speaker connected to the SURR. BACK/AMP ASSIGN terminals.

Normal :The surround back channel audio signals are output.

ZONE2 :The ZONE2 audio signals are output. Front A Bi-Amp : The bi-amp audio signals are output. Set this for bi-amp

playback of the front A speakers. Front B Bi-Amp : The bi-amp audio signals are output. Set this for bi-amp

playback of the front B speakers.

Front Height : The front height channel audio signals are output.

Speaker Conﬁ g.

Select speaker conﬁ guration and size. (bass reproduction capability)

NOTE

Select “Large” or “Small” not according to the physical size of the speaker but according to the low frequency reproduction capabilities based on the frequency set at “Crossover Frequency” (vpage 27).

Front : Set the front speaker size.

Large : Use of a large speaker that can adequately play back low

frequencies. Small : Use of a small speaker that has inadequate playback capacity for low frequencies.

If “Subwoofer” is set to “No”, “Front” is automatically set to “Large”.

•

Center : Set the presence and size of the center speaker.

Large : Use of a large speaker that can adequately play back low

frequencies. Small : Use of a small speaker that has inadequate playback capacity for low frequencies. None : Select when a center speaker is not connected.

• “Large” is not displayed when “Front” is set to “Small”.

• Even if “Center” has been set to “Large”, when “Front” is set to “Small”, the “Center” setting automatically switches to “Small”.

•

Subwoofer : Set the presence of a subwoofer.

Yes : Use a subwoofer. No : Select when a subwooofer is not connected.

When “Front” is set to “Small”, “Subwoofer” can automatically set

to “Yes”.

•

Use this procedure to set the speakers manually or if you wish to change the settings made with the Audyssey Auto Setup procedure.

Making the speaker settings (Speaker Setup)

Default settings are underlined.

See overleaf

Use this procedure to change the Audyssey Auto Setup settings or to change the various audio, video and display settings. The set can be used without changing these settings. Make these settings as necessary. For a description of “Menu map” and operating instructions, see page 18.

Items that can be set with the Manual Setup proceduren



 Making the speaker settings (Speaker Setup) vpage 25



Making the HDMI settings (HDMI Setup) vpage 28



Making the audio settings (Audio Setup) vpage 29



 Making other settings (Option Setup) vpage 30



 Making the ZONE2 settings (ZONE2 Setup) vpage 30

n Examples of Menu Screen Displays

Speaker Setup HDMI Setup Audio Setup

4-1.Speaker Setup

1.Amp Assign

2.Speaker Config.

3.Bass Setting

4.Distance

6.Crossover Freq.

7.Front Sp Setup

5.Channel Level

[ENT]:Select [RTN]:Back

4-2.HDMI Setup

Auto Lipsync : ON HDMI Audio Out : Amp HDMI Control : OFF

[RTN]:Back

4-3.Audio Setup

1.EXT.IN SW Level

2.2ch Direct/Stereo

3.Auto Surround Mode

4.EQ Customize

[ENT]:Select [RTN]:Back

ZONE2 Setup Option Setup

4-4.ZONE2 Setup

Level Lch : 0dB Level Rch : 0dB Vol.Display : Relative Vol.limit : OFF

Mute Lev. : Full

Power On Lev: Last

[RTN]:Back

4-5.Option Setup

1.Volume Control

2.Source Delete

3.On-Screen Display

4.Quick Select Name

7.Setup Lock

6.Display

5.ZONE Rename

[ENT]:Select [RTN]:Back

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu

Remote control

operation buttons

Displaying the menu

Cancel the menu

Settings

ENGLISH

Getting Started Connections Playback Remote Control Information Troubleshooting Speciﬁcations

Making detailed settings (Manual Setup)

Setting items Setting contents

Speaker Conﬁg.

Select speaker conﬁguration and size. (bass reproduction capability)

Settings

“S.Back” is displayed when the “Amp Assign” setting (vpage 25) is set to “Normal”.

Multi-Zone

“Front Height” is displayed when the “Amp Assign” setting (vpage

25) is set to “Front Height”.

NOTE

Surround : Set the presence and size of the Surround speakers.

Large : Use of a large speaker that can adequately play back low

• frequencies.

Small :Use of a small speaker that has inadequate playback capacity for

• low frequencies.

None : Select when the surround speakers are not connected.

•

“Large” is not displayed when “Front” is set to “Small”.

S.Back : Set the presence, size and number of surround back speakers.

Large : Use of a large speaker that can adequately play back low

• frequencies. Small : Use of a small speaker that has inadequate playback capacity for

• low frequencies. None :Select when the surround back speakers are not connected.

• 2sp :Use two surround back speakers.

• 1sp : Use only one surround back speaker. Surround back audio is output

• from the surround back L terminal.

• “Large” is not displayed when “Surround” is set to “Small”.

 • Even if “S.Back” is set to “Large”, the “S.Back” setting is automatically

switched to “Small” if “Surround” is set to “Small”.

NOTE

Even when the Surround Back Speaker setting is other than “None”, sound may not be emitted from the surround back speaker, depending on the playback source. In this case, “Surround Back” setting other than “OFF” (vpage 45).

Front Height : Set the front height speaker size.

Large : Use of a large speaker that can adequately play back low

• frequencies. Small : Use of a small speaker that has inadequate playback capacity for

• low frequencies. None : Select when a front height speaker is not connected.

•

• “Large” is not displayed when “Front” is set to “Small”.

• Even if “Front Height” is set to “Large”, the “Front Height” setting

is automatically switched to “Small” if “Front” is set to “Small”.

Setting items Setting contents

Bass Setting

Make the settings related to playback of low frequency signals (subwoofer and LFE).

This can be set when “Speaker Conﬁg.” – “Subwoofer” (vpage

25) is set to “Yes”.

Distance

Set the distance from the listening position to the speakers. Measure the distance from the listening position to the speakers beforehand.

Subwoofer Mode : Select low range signal to be reproduced by subwoofer.

LFE : Add the low frequency signal of the channel for which the speaker

• size is set to “Small” to the subwoofer signal and output it. LFE+Main : Add the low frequency signal of all channels to the subwoofer

• signal and output it.

• Play music or a movie source and select the mode offering the

strongest bass.

• Select “LFE+Main” if you want the bass signals to always be

produced from the subwoofer.

LPF for LFE : Set the upper limit of the low frequency signals output from the subwoofer.

80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz•

Unit : Set the unit of distance.

Feet

•

Meters

•

Step : Set the minimum variable width of the distance.

1ft / 0.1ft

•

0.1m / 0.01m

•

(Front L)/ FR (Front R)/ C (Center)/ SW (Subwoofer)/ SL (Surround L)/

•

FL SR (Surround R/ SBL (Surr. Back L)/ SBR (Surr. Back R)/ FHL (Front Height L)/ FHR (Front Height R) : Select the speaker you want to set, and set the

distance. Set the value that is closest to the measured distance.

0.0ft ~ 60.0ft / 0.00m ~ 18.00m

•

• The speakers that can be selected differ depending on the “Amp Assign” (vpage 25) and “Speaker Conﬁg.” (vpage 25) settings.

• Default settings :

Front/Center/Subwoofer/Front Height : 3.6 meters (12 feet) Surround/Surr. Back : 3.0 meters (10 feet)

NOTE

Set the difference in the distance between the speakers to less than 6.0 meters (20 feet). “Relocate Speaker” is displayed on the screen if an inappropriate distance is set. Default : Reset all distance settings to factory default.

Yes : Reset to the defaults.

• No : Do not reset to the defaults.

•

2

Remote control

operation buttons

Displaying the menu

: Cancel the menu

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu

ENGLISH

Making detailed settings (Manual Setup)

Getting Started

Setting items Setting contents

Channel Level

Set the volume of the test tone to be the same when it is output from each speaker.

Crossover Frequency

Outputs at below set frequency, each speaker’s bass signal output from the subwoofer. Set this according to the low frequency reproduction capabilities of the speakers you are using.

This can be set when “Speaker Conﬁg.” –

“Subwoofer” (vpage

25) is set to “Yes” or “No”.

Test Tone Start : Output test tones.

FL (Front L)/ C (Center)/ FR (Front R)/ SR (Surround R)/ SBRz (Surround Back R)/ SBLz (Surround Back L)/ SL (Surround L)/ FHL (Front Height L)/ FHR (Front Height R)/ SW (Subwoofer): Select

the speaker.

When the “S.Back” setting (vpage 26) is set to “1sp”, “SB” is displayed.

–12.0dB ~ +12.0dB (0.0dB) : Adjust the volume.

•

• When “Channel Level” is adjusted, the adjusted values are set for all the surround modes. To adjust the channel level separately for the different surround modes, use the operation see “Adjust the volume of the different speakers” (vpage 50).

• Speakers set to “None” in the “Speaker Conﬁg.” (vpage 25) settings are not displayed.

• Wheno is pressed while the subwoofer volume is set to “–12dB”, the “Channel Level” setting switches to “OFF”.

• If output of the test tones begins while the muting mode is set, the muting mode is canceled.

Default : Reset all channel level settings to factory default.

Yes : Reset to the defaults.

•

No : Do not reset to the defaults.

• Crossover : Outputs at below set frequency, each speaker’s bass signal

output from the subwoofer.

40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /

•

250Hz Advanced : Set the low frequency signals to be output from the signals

• of the respective speakers to the subwoofer. Front / Center / Surround / S.Back / Front Height : Select the

• speaker.

· 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /

250Hz : Set the crossover frequency.

Setting items Setting contents

Crossover Frequency

Front Speaker Setup

Select front speakers to use for each surround mode.

• Always set the crossover frequency to “80 Hz”. When using small speakers, however, we recommend setting the crossover frequency to a higher frequency.

• For speakers set to “Small”, sound below the crossover frequency is cut from the sound output. The cut bass sound is output from the subwoofer or front speakers.

• The speakers that can be set when “Advanced” is selected differ according to the “Bass Setting” setting (vpage 26).

· When “LFE” is selected, speakers set to “Small” at “Speaker Conﬁg.” (vpage 25) can be set.

· When “LFE+Main” is selected, speakers can be set regardless of the speaker size setting.

Setting : Choose the method for setting the front speakers.

Normal : The front speakers are set using the .

• Custom : The front speakers used for the different playing modes are

• set in advance.

DIRECT/STEREO : The front speakers used in the direct, stereo and pure direct play modes are set in advance.

A : Front speaker A is used.

• B : Front speaker B is used.

• A+B : Both front speakers A and B are used.

•

MULTI CH : The front speakers used in modes other than the direct, stereo and pure direct play modes are set in advance.

A : Front speaker A is used.

• B : Front speaker B is used.

• A+B : Both front speakers A and B are used.

•

NOTE

• When set to “Custom”, does not operate.

• The front speaker setting stored for the “Quick Select” function is given priority.

Connections Playback Remote Control Information Troubleshooting

Settings

Multi-Zone

Speciﬁcations

Remote control

operation buttons

Displaying the menu

: Cancel the menu

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu

2

Getting Started Connections Playback Remote Control Information Troubleshooting Speciﬁ cations

ENGLISH

Multi-Zone

Setting items Setting contents

Auto Lip Sync

Automatic compensation for timing shift in audio and video output.

ON : Compensated. OFF : Not compensated.

HDMI Audio Out

Select HDMI audio output device.

Amp : Use speakers connected to AVR-1910 for audio playback. TV : Use speakers of TV for audio playback.

NOTE

When the HDMI control function is operating, the setting of audio playback in the connected TV takes priority (vpage 49 “Controlling HDMI-

compatible devices from the AVR-1910 (HDMI Control Function)”).

HDMI Control

External devices can be controlled from the AVR1910 and the AVR-1910 can be controlled from external devices.

NOTE

The HDMI control function controls operations of a TV that is compatible with the HDMI control function. Make sure that the TV and HDMI are connected when you perform HDMI control.

ON : Use the HDMI control function. OFF : Do not use the HDMI control function.

• Please consult the operating instructions for each connected device to check the settings.

• For details on the HDMI control function, see “Controlling HDMIcompatible devices from the AVR-1910 (HDMI Control Function)” (vpage 49).

NOTE

• When “HDMI Control” is set to “ON”, it consumes more standby

power.

• When not using this unit for a long period, we recommend that you press

to turn off (jOFF) the power.

• When the “HDMI Control” setting has been changed, always turn off the

power to the connecting devices afterwards and then turn back on.

• The “HDMI Control” does not work when the power to the equipment is

off.

• When “HDMI Control” is set to “ON”, power is supplied constantly to the

AC outlet (UNSWITCHED).

Standby Source

Set the HDMI connector for HDMI signal input during standby.

This can be set when “HDMI Control” is set to “ON”.

Last : Standby with last used input source during power on. HDMI1 / HDMI2 / HDMI3 / HDMI4 : The standby mode is set at the input

source assigned to the respective.

Make settings for HDMI video/audio output.

Making the HDMI settings(HDMI Setup)

Default settings are underlined.

Setting items Setting contents

Power Off Control

The power of the AVR-1910 and external device turn off together.

This can be set when “HDMI Control” is set to “ON”.

ON：Switched. OFF：Not switched.

• Please consult the operating instructions for each connected device to check the settings.

• For details on the HDMI control function, see “Controlling HDMIcompatible devices from the AVR-1910 (HDMI Control Function)” (vpage 49).

Making detailed settings (Manual Setup)

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu

Remote control

operation buttons

Displaying the menu

Cancel the menu

Settings

2

Getting Started

Connections Playback Remote Control Information Troubleshooting

Speciﬁ cations

ENGLISH

Multi-Zone

Setting items Setting contents

Auto Surround Mode

Make setting for memorizing surround mode setting for each input signal type.

ON : Memorize settings. Most recently stored surround mode is automatically selected.

OFF : Do not memorize settings. Surround mode does not change according to input signal.

The auto surround mode function lets you store in the memory the

surround mode last used for playing the four types of input signals listed below.

q Analog and PCM 2-channel signals w Dolby Digital and DTS 2-channel signals e Dolby Digital and DTS multi-channel signals r Multi-channel signals other than Dolby Digital and DTS (PCM, etc.)

NOTE

When playing in the PURE DIRECT mode, the surround mode does not change even if the input signal is changed.

EQ Customize

Set so that unused equalizer settings are not displayed when is used.

Audyssey Byp. L/R / Audyssey Flat / Manual

Used Not Used

NOTE

• Set so that the “Audyssey Byp. L/R” and “Audyssey Flat” settings can be

made when the Audyssey Auto Setup procedure is performed.

• Equalizer settings for which “Not Used” is set with the Quick Select

function cannot be stored and called out.

•

Setting items Setting contents

EXT.IN SW Level

Set the playback level of the analog subwoofer signals input from the external input terminals (EXT.IN).

+15dB : This is the recommended level. +10dB / +5dB / 0dB : Select the level according to the player being used.

2ch DIRECT/STEREO

Make speaker settings for 2channel mode playback.

Setting : Select the method for setting the speakers used in the 2-channel direct and stereo playback modes.

Basic : The settings at “Speaker Setup” (vpage 25) are applied. Custom : Make separate settings for 2-channel mode. Front : Set the front speaker size.

Large : Use of a large speaker that can adequately play back low

frequencies. Small : Use of a small speaker that has inadequate playback capacity for low frequencies.

SW : Set the presence of a subwoofer.

Yes : Use a subwoofer. No : Select when a subwoofer is not connected.

SW Mode : Select low range signal to be reproduced by subwoofer.

LFE : Add the low frequency signal of the channel for which the speaker

size is set to “Small” to the subwoofer signal and output it. LFE+Main : Add the low frequency signal of all channels to the subwoofer signal and output it.

Crossover : Outputs at below set frequency, each speaker’s bass signal output from the subwoofer.

40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz

Distance FL / Distance FR : Select the speaker you want to set, and set

the CH Level. Set the value that is closest to the measured distance.

0.0ft ~ 60.0ft (12.0ft) / 0.00m ~ 18.00m(3.6m)

CH Level FL/ CH Level FL FR : Select the speaker you want to set, and

set the CH Level. Adjust the level of each channel.

–12.0dB ~ +12.0dB(0.0dB)

•

Make settings for audio playback.

Making the audio settings (Audio Setup)

Default settings are underlined.

Making detailed settings (Manual Setup)

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu

Remote control

operation buttons

Displaying the menu

Cancel the menu

Settings

0

Getting Started Connections Playback Remote Control Information Troubleshooting Speciﬁ cations

ENGLISH

Multi-Zone

Making detailed settings (Manual Setup)

Setting items Setting contents

Volume Control

Set the MAIN ZONE volume setting.

Volume Display : Set the volume display method.

Relative : The volume is displayed within the range of – – –dB (Minimum),

–80.5 dB ~ +18 dB. Absolute : The volume is displayed within the range of 0, 1 ~ 99.

•

Vol.Limit : Make a setting for maximum volume.

OFF : Do not set a maximum volume. –20dB(61) / –10dB(71) / 0dB(81)

•

Power On Level : This sets the volume set when the MAIN ZONE’s power is turned on.

Last : Use the memorized setting from the last session. – – – : Always use the muting on condition when power is turned on.

–80dB(1) ~ +18dB(99) : The volume is adjusted to the set level.

•

Mute Level : This sets the amount of attenuation of the volume when the mute mode is set in the MAIN ZONE.

Full : The sound is cut off entirely. –40dB : The sound is attenuated by 40 dB. –20dB : The sound is attenuated by 20 dB.

•

Source Delete

Remove input sources that are not used from the display.

TUNER / CD / DVD / HDP / TV / SAT/CBL / VCR / DVR / V.AUX : Select the sources you do not want to use.

ON : Use this source. Delete : Do not use this source.

NOTE

•The currently selected input source cannot be set.

•Input sources set to “Delete” cannot be selected using .

•

On-Screen Display

Make the settings related to displays on the TV screen.

Screensaver : Make screensaver settings.

ON : The screen switches to the screensaver if no operation is performed for approximately 3 minutes while a menu is displayed or while an iPod screen is displayed. When you press uio p, the screen saver is

cancelled and the screen before that screen saver started is displayed. OFF : Turn the screensaver function off.

•

Text : The mode name is displayed when the operation for switching the surround mode, input mode, etc., is performed.

ON : Turn display on. OFF : Turn display off.

•

Master Volume : Master volume display during adjustment.

Bottom : Displayed at the bottom of the screen. Top : Displayed at the top of the screen.

OFF : Turn display off.

•

Making other settings (Option Setup)

Default settings are underlined.

Setting items Setting contents

Level Lch

Adjust the left channel output level.

–12dB ~ +12dB (0dB)

Level Rch

Adjust the right channel output level.

–12dB ~ +12dB (0dB)

Volume Display

Set the ZONE2 volume display method.

Relative : The volume is displayed within the range of – – –dB (Minimum), –80 dB ~ +18 dB.

Absolute : The volume is displayed within the range of 0, 1 ~ 99.

Vol.Limit

Make a setting for maximum volume.

OFF : Do not set a maximum volume. –20dB / –10dB / 0dB

Power On Level

Deﬁ ne the volume setting that is active when the power is turned on.

Last : Use the memorized setting from the last session. – – – : Always use the muting on condition when power is turned on.

–80dB ~ +18dB (99) : The volume is adjusted to the set level.

Mute Level

Set the amount of attenuation when muting is on.

Full : The sound is cut off entirely. –40dB : The sound is attenuated by 40 dB. –20dB : The sound is attenuated by 20 dB.

• The volume is displayed using the display method set at “Volume Display” (vpage 30).

•Set the main volume at “Volume Control” (vpage 30).

Make settings for audio playback in a ZONE2 system. “ZONE2 Setup” is displayed when ZONE2 is selected with “Amp Assign” (vpage 25).

Making the ZONE2 settings (ZONE2 Setup)

Default settings are underlined.

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu

Remote control

operation buttons

Displaying the menu

Cancel the menu

Settings

ENGLISH

Making detailed settings (Manual Setup)

Getting Started

Setting items Setting contents

On-Screen Display

Make the settings related to displays on the TV screen.

Tuner Information : This sets the time the on-screen display is displayed when a tuneroperation is performed.

Always : Show display continuously.

•

30sec : Show display for 30 seconds after operation.

•

10sec : Show display for 10 seconds after operation.

•

OFF : Turn display off.

•

iPod Information

This sets the time the on-screen display is displayed

when an iPodoperation is performed.

Always : Show display continuously.

•

30sec : Show display for 30 seconds after operation.

•

10sec : Show display for 10 seconds after operation.

•

OFF : Turn display off.

•

Quick Select Name

Change the Quick Select name.

Rename Label : Change the display name of the selected “Quick Select” setting.

1. Use ui to select the name of the Quick Select setting you want

to change, then press .

2.Use o p to set the cursor to the character you want to change.

3. Use ui to change the character, then press .

• Up to 16 characters can be input.

• The input character type can be switched by pressing display name is being changed.

• The types of characters that can be input are as shown below.

GCapital lettersHA B C D E FGHIJKLM N O P Q RST U VWXYZ GSmall lettersH abcdef g h i j klmnopqr s t u v w x yz GSymbolsH ’ ( ) b + – . / : ; < = > ? [ ] GNumbersH 0123 4 5 6 7 89(space)



4. Repeat steps 2 and 3 to change the display name. Template : The display name can be changed by selecting “Operation” and

“Device Name” from the previously set templates.

ui to select the name of the Quick Select setting you want

1. Use to change, then press .

2. Use ui to select “Template”, then press .

3. Useui to select “Operation”, then press .

•

Watch / Listen to / Play / For

4. Useuio p to select “Device Name ”, then press .

•

DVD / Blu-Ray / HDP / TV / Cable TV / Satellite / VCR / DVR / iPod / V.AUX / LD / Movie (When “Operation” is selected to “Watch”.)

• CD / TUNER / iPod / MD / TAPE / Music (When “Operation” is selected to “Listen to”.)

• PC / Game (When “Operation” is selected to “Play”.)

• Father / Mother / Son / Daughter / Brother / Sister / Grandfather

/ Grandmother / Me (When “Operation” is selected to “For”.)

while the

Setting items Setting contents

Quick Select Name

Zone Rename

Rename the display names of the different zones as desired.

Default : The changed display names are reset to the defaults.

Yes : Reset to the defaults.

•

No : Do not reset to the defaults.

•

ui to select the zone name you want to change, then press

1. Use .

MAIN ZONE / ZONE2

2. Use o p to set the cursor to the character you want to change.

3. Use ui to change the character, then press .

• Up to 10 characters can be input.

• The input character type can be switched by pressing display name is being changed.

• The types of characters that can be input are as shown below.

4. Repeat steps 2 and 3 to change the display name.

Display

Adjust display brightness of the receiver.

Bright : Normal display brightness.

•

Dim : Reduced display brightness.

•

Dark : Very low display brightness.

•

OFF : Turns the display off.

•

Switching is also possible by pressing on the main unit.

Setup Lock

Protect settings from inadvertent change.

ON : Turn protection on.

•

OFF : Turn protection off.

•

When “Setup Lock” is set to “ON”, the settings listed below can

no longer be changed. Also, “SETUP LOCKED!” is displayed if you attempt to operate related settings.

・RESTORER ・Dynamic Volume ・MultEQ ・Channel Level ・Dynamic EQ ・Audio Delay

Connections Playback Remote Control Information Troubleshooting

Settings

while the

Multi-Zone

Speciﬁcations

Remote control

operation buttons

Displaying the menu

: Cancel the menu

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu



2

Getting Started Connections Playback Remote Control Information Troubleshooting Speciﬁ cations

ENGLISH

Multi-Zone

Making the input settings (Input Setup)

Make the settings related to the currently selected input source. Before displaying the menu screen, press to switch to the input source to be set.

The items that can be set differ according to the selected input source. The set can be used without changing these settings. Make these settings as necessary. For a description of “Menu map” and operating instructions, see page 18.

n Examples of Menu Screen Displays

Assign Video Input Mode

5-1-1.Input Assign

HDMI Digi Comp

DVD 1 C1 1

HDP 2 TV 01

VCR/iPod DVR 4 02 2

SAT/CBL 3 C2

[ENT]:Select [RTN]:Back

5-2.Video

Video Select: Source

i/p Scaler : Anlg/HDMI Resolution A: Auto Resolution H: Auto

Aspect : Full

Progre.Mode : Auto

[RTN]:Back

5-3.Input Mode

Input Mode : Auto

Decode Mode : Auto

[RTN]:Back

Rename Source Level iPod Playback Mode

5-4.Rename

DVD : DVD

Defaulut

[ ]:Up/Down [ ]:Rename [RTN]:Back

5-5.Source Level

Digital Input : 0dB

[RTN]:Back

Analog Input : 0dB

5-6.iPod Playback Mode

Shuffle Mode : OFF

[RTN]:Back

Repeat Mode : One

Auto Preset Preset Skip Preset Name

5-1.Auto Preset

Auto Tuning Preset Station Memory Storing Preset Memory

Start

[ENT]:Start [RTN]:Back

5-2.Preset Skip

Block : A

A Block Presets: ON A1 FM 87.50MHz : ON A2 FM 89.10MHz : ON

A4 FM108.00MHz : ON

A3 FM 98.10MHz : ON

A5 FM 90.10MHz : ON A6 FM 90.10MHz : ON A7 FM 90.10MHz : ON A8 FM 90.10MHz : ON

5-3.Preset Name

Block: A

A1FM 87.50MHz: A2FM 89.10MHz: A3FM 98.10MHz:

A5FM 90.10MHz:

A4FM108.00MHz:

A6FM 90.10MHz: A7FM 90.10MHz: A8FM 90.10MHz: [ENT]:Select [RTN]:Back

Items that can be set with the Input Setup proceduren

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu

Remote control

operation buttons

Displaying the menu

Cancel the menu

Changing the Input Sources Assigned to the Input Terminals (Assign) vpage 33

Making the video settings (Video) vpage 34

Changing the Input Source’s Input Mode and Decoding mode (Input mode) vpage 34

Changing the Input Source’s Display Name (Rename) vpage 35

Correcting the Input Source’s Playback Level (Source Level) vpage 35

Setting the iPod Playback Mode (iPod Playback Mode) vpage 35

Setting the Preset Channels to be Skipped (Preset Skip) vpage 36

Presetting Radio Stations (Auto Preset) vpage 36

Assign Name to a Preset Memory (Preset Name) vpage 36

Settings

Changing the Input Sources Assigned to the Input Terminals (Assign)

Default settings are underlined.

Setting items Setting contents

Input Assign(HDMI)

Assign input sources to input connectors.

Input Assign(Digital)

Assign input sources to input connectors.

HDMI : The

sources are assigned to the HDMI input terminals as shown below.

HDMI1 / HDMI2 / HDMI3 / HDMI4

•

None : Do not assign an HDMI input terminal to the currently selected

• input source.

bUpon purchase, the settings of the different input sources are as shown

below.

Input source

Default setting

•When HDMI is assigned to an input source, the audio signal switches

to HDMI along with the video signal. To use with the digital audio input connectors assigned, set menu “Input Mode” (vpage 34) to “Digital”.

• When the AVR-1910 and TV are connected with an HDMI cable, if the

TV is not compatible with HDMI audio signal playback, only the video signals are output to the monitor.

• The audio signals input from the analog, digital and EXT. IN connectors

are not output to the TV.

NOTE

When “HDMI Control” is set to “ON”, HDMI cannot be assigned to “TV” at the “HDMI” settings (vpage 28).

Digital : The input sources are assigned to the digital audio input terminals as shown below.

C1 (COAX1) / C2 (COAX2) / O1 (OPT1) / O2 (OPT2)

• None ： Do not assign a digital input terminal to the currently selected

• input source.

bUpon purchase, the settings of the different input sources are as shown

below.

Input source Default setting COAX1 None OPT1 COAX2 None

DVD HDP TV SAT/CBL VCR DVR V.AUX

HDMI1 HDMI2 None HDMI3 None HDMI4 None

DVD HDP TV SAT/CBL VCR DVR V.AUX CD

DVD HDP TV SAT/CBL VCR

input

Setting items Setting contents

Input Assign(Component)

Assign input sources to input connectors.

iPod Dock

Change the input source to which the control dock for iPod is assigned.

ENGLISH

Making the input settings (Input Setup)

Component : The

input sources are assigned to the component video input terminals as shown below.

COMP1 (Component video 1 input terminal) / COMP2 (Component

●

video 2 input terminal)

None

: Do not assign the component video input terminals to the currently

●

selected input source.

bUpon purchase, the settings of the different input sources are as shown

below.

Input source

Default setting

The control dock for iPod can be assigned to the

DVR V.AUX CD

Assign

: Assign the currently selected input source to the Control Dock for

iPod input.

None

: Do not assign the currently selected input source to the Control Dock

for iPod input.

• With the default settings, the control dock for iPod can be used connected to the VCR (iPod) connector.

• Even if “iPod Dock” is set to “Assign”, if AVR-1910 and control dock for iPod are not connected, the input is used as the normal input source.

DVD HDP TV SAT/CBL VCR DVR V.AUX

COMP1 None None None None COMP2 None

DVD SAT/CBL VCR

input sources.

Getting Started

Connections Playback Remote Control Information Troubleshooting

Settings

Multi-Zone

Speciﬁcations

Input source Default setting OPT2 None None

Remote control

operation buttons

DVR V.AUX CD

Displaying the menu

: Cancel the menu

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu



ENGLISH

Auto HDMI Digital

AnalogEXT. IN

Getting Started Connections Playback Remote Control Information Troubleshooting Speciﬁcations

Making the input settings (Input Setup)

Making the video settings (Video)

Default settings are underlined.

The items that can be set depend on the input source and the “Assign” setting.

Setting items Setting contents

Video Select

Switch video input source while listening to audio

Settings

signal.

Multi-Zone

i/p Scaler

The input source’s resolution is converted to the resolution set at “Resolution”.

Resolution

Set the output resolution. Resolution A : Analog Video Resolution H : HDMI

Progressive Mode

Select optimum progressive mode for video material.

Aspect

Set the aspect ratio of the video signal output from the HDMI terminal.

Source : Play the picture and sound of the input source. DVD / HDP / TV / SAT/CBL / VCR / DVR / V.AUX : Select video input

source to view. This can be set for individual input sources.

NOTE

It is not possible to select HDMI input signals.

• When playing HDMI video input signals, the analog video signal of

• another input source cannot be selected for the HDMI video output. Input sources for which “Delete” is selected at “Source Delete” (vpage

•

30) cannot be selected. Input sources for which “None” is selected at “Assign” (vpage 33)

• cannot be selected.

•

This can also be set by pressing .

• To cancel, press to select “Source”.

This can be set to the input sources.

OFF : Do not use i/p scaler function. Analog : Analog signals are converted to HDMI signals. Analog and HDMI : Both analog signals and HDMI signals are converted

to the desired HDMI resolution. This can be set when the input source is set to

SAT/CBL VCR DVR V.AUX

other than “OFF”. AUTO : Detect monitor panel resolution and automatically set output resolution. 480p/576p / 1080i / 720p / 1080p : Select the output resolution.

This can be set when the input source is set to

SAT/CBL VCR DVR V.AUX

other than “OFF”. AUTO : The video material is automatically detected and the appropriate mode is set.

Video1 : Select mode suitable for video playback. Video2 : Select mode suitable for video and 30-frame ﬁlm material

playback.

This can be set when the input source is set to

SAT/CBL VCR DVR V.AUX

other than “OFF”.

Normal : Output at 4:3 aspect ratio. Full : Output at 16:9 aspect ratio.

DVD HDP TV SAT/CBL VCR DVR V.AUX

, and when “i/p Scaler” is set to anything

DVD HDP TV

Changing the Input Source’s Input Mode and Decoding mode (Input Mode)

Default settings are underlined.

The selectable input modes depend on the input source and “Assign” setting (vpage 33 “Changing the input sources assigned to the input terminals”).

Setting items Setting contents

Input Mode

Set the audio input modes for the different input sources.

Auto : Automatically detect input signal and perform playback. HDMI : Play only signals from HDMI input. (Excluding CD) Digital : Play only signals from digital input. Analog : Play only signals from analog input. EXT. IN : Play only signals from EXT. IN input.

bUpon purchase, the settings of the different input sources are as shown

below.

Input source

Default setting

Input source

Default setting

•The “HDMI” settings are made for input sources for which HDMI

input terminals are assigned at “Assign” (vpage 33).

 •The “Digital” settings are made for input sources for which digital

input terminals are assigned at “Assign” (vpage 33).

•

When a digital signal is properly input, the “ ” indicator lights on the display. If the “ ” indicator does not light, check the digital input connector assignment and the connections.

• The surround mode cannot be set if the input mode is set to “EXT. IN”.

•

This can also be set by pressing . Each time you press the button, the input mode display will change.

DVD HDP TV SAT/CBL VCR

Auto HDMI Digital Auto Analog

DVR V.AUX CD TUNER

Auto Analog Analog Analog



Remote control

operation buttons

Displaying the menu

: Cancel the menu

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu

ENGLISH

Making the input settings (Input Setup)

Getting Started

Setting items Setting contents

Decode Mode

Set the input source’s decoding mode.

Auto : Detect type of digital input signal and decode and play automatically.

PCM : Decode and play only PCM input signals. DTS : Decode and play only DTS input signals.

• This can be set for input sources for which “HDMI” or “Digital” is assigned at “Assign” (vpage 33).

• Normally set this to “Auto”.

Changing the Input Source’s Display Name (Rename)

Default settings are underlined.

Use this procedure to change the display name of the currently selected input source.

Setting items Setting contents

Rename

Change the input source’s display name to the desired name.

Default

The changed display names are reset to the defaults.

1.Use o p to set the cursor to the character you want to change.

2.Use ui to change the character, then press .

Up to 8 characters can be input.

• The input character type can be switched by pressing while the

•

display name is being changed.

• The types of characters that can be input are as shown below.



Yes : Reset to the defaults. No : Do not reset to the defaults.

Correcting the Input Source’s Playback Level (Source Level)

Default settings are underlined.

Use this procedure to correct the playback level of the currently selected input source's audio input. Set this if there are differences in the input volume levels between the different sources. The analog input level and digital input level can be corrected separately.

Setting items Setting contents

Source Level (Analog)

Correct the playback level of the analog audio input.

Source Level (Digital)

Correct the playback level of the digital audio input.

–12dB ~ +12dB (0dB)

Setting the iPod Playback Mode (iPod Playback Mode)

Default settings are underlined.

This can be selected for input sources for which “Assign” is assigned at the “iPod Dock” (vpage

33) setting.

Setting items Setting contents

Repeat

Make settings for repeat mode.

Shufﬂe

Make settings for shufﬂe mode.

All : Repeat all songs. One : Repeat the current song. OFF : Cancel repeat mode.

n When DENON control dock for iPod ASD-1R or ASD-11R is

connected Songs : Shufﬂe all songs. Albums : Shufﬂe songs from current album only. OFF : Cancel shufﬂe mode.

Connections Playback Remote Control Information Troubleshooting

Settings

Multi-Zone

Remote control

operation buttons

Displaying the menu

: Cancel the menu

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

Speciﬁcations

: Return to previous menu



ENGLISH

Getting Started Connections Playback Remote Control Information Troubleshooting Speciﬁcations

Making the input settings (Input Setup)

Presetting Radio Stations (Auto Preset)

Setting items Setting contents

Auto Preset

Use the auto preset function to program radio stations.

Settings

Setting the Preset Channels to be Skipped (Preset Skip)

Multi-Zone

Setting items Setting contents

Preset Skip

Set the preset memories that you do not want to display when tuning.

Default settings are underlined.

This can be set when the source is set to Start : Start the auto preset process.

If an FM station cannot be preset automatically, select the desired station by tuning it in manually, then preset it manually.

This can be set when the source is set to

A ~ G : Select the preset channel(s) you do not want to display.

ON : Display this number.

•

Skip : Skip this number.

•

If you set “Block Presets” to “Skip”, you can skip the preset memory blocks (A to G).

TUNER

Default settings are underlined.

TUNER

Assign Name to a Preset Memory(Preset Name)

Default settings are underlined.

Setting items Setting contents

Preset Name

Assign name to a preset memory.

This can be set when the source is set to

1.Use ui to select the preset channel name you want to change,

then press .

2.Use o p to set the cursor to the character you want to change.

3.Use ui to change the character, then press .

• Up to 8 characters can be input.

• The input character type can be switched by pressing display name is being changed.

• The types of characters that can be input are as shown below.



4. Repeat steps 2 and 3 to change the display name.

TUNER

while the



Remote control

operation buttons

Displaying the menu

: Cancel the menu

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu



ENGLISH

Getting Started

Connections Remote Control Information Troubleshooting

Speciﬁ cationsMulti-ZoneSettings

Playback

Playing Components

Prepare for playback.

 qTurn on the power of the TV, subwoofer and player.

  wSet the TV’s input to the AVR-1910.   eLoad the disc in the player.

Turn on the AVR-1910’s power.

(vpage 17“Turning the Power On”)

Press and select the input

source.

If “TUNING PRESET” is selected for preset channel, press before turning

Play the component connected to

the AVR-1910.

Make the necessary settings on the

player (language setting, subtitles setting, etc.) beforehand.

Use to adjust the volume.

GVariable rangeH

– – – –80.5dB ~ 18.0dB

※The variable range differs according to the input signal and channel

level setting.

Select the desired surround mode.

(vpage 42“Selecting the Surround Mode”)

Adjust the desired sound  eld effects.

(vpage 44“Adjusting the Sound Field Effects”)

The following describes the procedure for playing Blu-ray disc/ DVD players. Use the same procedure to play other components.

Playing Blu-ray Disc / DVD Players

The music / video on an iPod can be played by using the control dock for iPod (ASD-1R, ASD-11R, ASD-3N or ASD-3W sold separately).

Connect the control dock for iPod beforehand(vpage 14“iPod®”).

iPod® Playback

Prepare for playback.

q Set the iPod in the DENON control dock

for iPod.

w Assign the control dock for iPod’s input

(vpage 33).

 eSet to “MAIN/TV” to “MAIN”.

Turn on the AVR-1910’s power.

(vpage 17“Turning the Power On”)

Press to select the input source assigned in step 1-

w above.

(iPod screen)

b If the screens above are not displayed, the iPod may not be

properly connected. Try connecting again.

Listening to music on an iPod

OK to disconnect.

Front

Adjusting the Sound Field Effects (Parameter)

(vpage 44)

Playing Components (vpage 37)

n Playing Blu-ray Disc/DVD Players (vpage 37) n iPod® Playback (vpage 37) n Listening to FM/AM Broadcasts (vpage 39) n Operations During Playback (vpage 41)

n Operation Flow

 Before starting playback, make the connections between the

different components and the settings on the receiver.

Selecting the Surround Mode (vpage 42)

q Standard Playback (vpage 42) w Playing in a DENON original surround mode

(vpage 43)

e Direct Playback (vpage 43) r Stereo Playback (vpage 43)

t Playing the Pure Direct mode (vpage 43)

NOTE

●Also refer to the operating instructions of the connected

components when playing them.

●External devices can be controlled by remote control unit

(vpage 52 “Operating the Connected Devices by Remote Control Unit”).

See overleaf

Front

Playback

ENGLISH

Getting Started Connections Remote Control Information Troubleshooting SpeciﬁcationsMulti-ZoneSettings

Press and hold it down for a 2 seconds or more to

select the display mode.

There are two modes for display the contents recorded on the iPod.

Playback

Browse mode

Remote mode

Display mode

Playable

ﬁles

Active

buttons

z1： When using an ASD-11R, ASD-3N or ASD-3W control dock for

iPod.

z2： Video may not be output, depending on the combination of

ASD-1R or ASD-11R and iPod.

：Displayed on the TV screen.

：Displayed on the iPod’s screen.

Browse mode Remote mode

Audio ﬁle

Picture ﬁle

Video ﬁle

Remote control unit (AVR-1910)

iPod

S S



S S

A S

Use ui to select the menu, then

press or p to select the music or video le to be played.

Press or p.

Playback starts.

Use to adjust the volume.

GVariable rangeH

※The variable range differs according to the input signal and channel

level setting.

Select the desired surround mode.

(vpage 42“Selecting the Surround Mode”)

Adjust the desired sound eld effects.

(vpage 44“Adjusting the sound Field Effects”)

– – – –80.5dB ~ 18.0dB

Playing Components

n To stop

During playback, either press and hold or press .

n Stopping playback temporarily

During playback, press or . Press again to resume playback.

Front

Viewing Still Pictures or Videos on the iPod

Photo and video data on the iPod can be viewed on the monitor. Only

• for iPod equipped with slideshow or video functions. (When using an ASD-1R or ASD-11R) Video may not be output, depending on the combination of ASD-1R

• or ASD-11R and iPod.

n To cue to the beginning of a track

During playback, either press (to cue to

the current track) or (to cue to the next track).



n Repeat playback and shufﬂe

playback

 “iPod Playback Mode” (vpage 35)

Press and hold to set the Remote

mode.

“Remote iPod” is displayed on the AVR1910’s display.

Watching the iPod’s screen, use ui

to select “Photos” or “Videos”.

Front

Press until the image you want to

view is displayed.

Use the RESTORER mode to expand the low and high frequency

Front

• components of compressed audio ﬁles and achieve a richer sound.

The default setting is “Mode3” (vpage 47). To check the name of the title, the artist or the

• album when playing in browse mode, press

The time (default : 30 sec) for which the on-

• screen display are displayed can be set at

menu “iPod Information” (vpage 31). Press

uiop to return to the original screen.

Press and set the AVR-1910’s power to the

• standby mode before disconnecting the iPod. Also switch the input source to one to which the menu “iPod dock” is not assigned before disconnecting the iPod.

NOTE

Depending on the type of iPod and the software version, some

• functions may not operate.

DENON will accept no responsibility whatsoever for any loss of iPod

• data.

Front

“TV Out” at the iPod’s “Slideshow Settings” or “Video Settings” must be set to “On” in order to display the iPod’s photo data or videos on the monitor. For details, see the iPod’s operating instructions.

iPod is a trademark of Apple Inc., registered in the U.S. and other countries. The iPod may only be used to copy or play contents that are not copyrighted or contents for which copying or playback is legally permitted for your private use as an individual. Be sure to comply with applicable copyright legislation.

8

Listening to FM/AM Broadcasts

Basic Operation

Set to “MAIN/TV” and

Press to select “TUNER”.

to “MAIN”.

Front

Press to select “FM” or “AM”.

Tune in the desired broadcast station.

q To tune in automatically (Auto Tuning)

Press to light the “AUTO” indicator on

the display, then use to select the station you want to hear.

w To tune in manually (Manual Tuning)

Press to turn off the display’s “AUTO”

indicator, then use to select the station you want to hear.

• If the desired station cannot be tuned in with auto tuning, tune it in manually.

• When tuning in stations manually, press and hold to change frequencies continuously.

• The time (default : 30 sec) for which the on-screen display are displayed can be set at menu“On-Screen Display” (vpage 31).

Rear

Presetting Radio Stations (Preset Memory)

Your favorite broadcast stations can be preset so that you can tune them in easily. Up to 56 stations can be preset.

Tune in the broadcast station you want to preset.

Press .

Front

Press

in which the station is to be preset.

Press to select the preset number (1 to 8).

to select the block (A to G)

Press again to complete the setting.

• To preset other stations, repeat steps 1 to 5.

• Stations can be preset automatically at menu “Auto Preset” (vpage

36).

NOTE

Preset stations are erased by overwriting them.

ENGLISH

Playing Components

Listening to Preset Stations

Press to select the memory block (A to G).

Press to select the desired preset channel (1

to 8).

You can also operate via the main unit. In this case, perform the following operations.

• Press , then turn on the main unit to select the preset radio channel.

n Default settings

Auto tuner presets

A1 ~ A8

B1 ~ B8

C1 ~ C8 D1 ~ D8 E1 ~ E8

F1 ~ F8

G1 ~ G8

87.5 / 89.1 / 98.1 / 108.0 / 90.1 / 90.1 / 90.1 /

90.1 MHz 522 / 603 / 999 / 1404 / 1611 kHz,

90.1 / 90.1 / 90.1 MHz

90.1 MHz

Getting Started

Connections Remote Control Information Troubleshooting

Playback



SpeciﬁcationsMulti-ZoneSettings

ENGLISH

Getting Started Connections Remote Control Information Troubleshooting SpeciﬁcationsMulti-ZoneSettings

Playing Components

RDS (Radio Data System)

RDS (works only on the FM band) is a broadcasting service which allows a station to send additional information along with the regular radio program signal. The following three types of RDS information can be received with this unit:

n Program Type (PTY)

PTY identiﬁes the type of RDS program. The program types and their displays are as follows:

NEWS News AFFAIRS Current Affairs

Playback

INFO Information SPORT Sports EDUCATE Education DRAMA Drama CULTURE Culture SCIENCE Science VARIED Varied POP M Pop Music ROCK M Rock Music

EASY M

LIGHT M Light Classical CLASSICS Serious Classical OTHER M Other Music

n Trafﬁc Program (TP)

TP identiﬁes programs that carry trafﬁc announcements. This allows you to easily ﬁnd out the latest trafﬁc conditions in your area before leaving home.

Easy Listening Music

WEATHER Weather FINANCE Finance

CHILDREN

SOCIAL Social Affairs RELIGION Religion PHONE IN Phone In TRAVEL Travel LEISURE Leisure JAZZ Jazz Music COUNTRY Country Music NATION M National Music OLDIES Oldies Music FOLK M Folk Music DOCUMENT Documentary

Children’s programmes

RDS Search

Use this function to automatically tune to FM stations that provide the RDS service.

Set to “MAIN/TV” and

Press to select “TUNER”.

to “MAIN”.

Front

Press to select “RDS SEARCH”.

Press .

The search for RDS stations begins

automatically.

b If no RDS stations are found with the

above operation, all the reception bands are searched.

b When a broadcast station is found, that

station’s name appears on the display.

To continue searching, repeat steps

2 to 3.

b If no RDS station is found when all the frequencies have been

searched, “NO RDS” is displayed.

PTY Search

Use this function to ﬁnd RDS stations broadcasting a designated program type (PTY). For a description of each program type, refer to “Program Type (PTY)”.

Set to “MAIN/TV” and

Press to select “TUNER”.

to “MAIN”.

Front

Press to select “PTY SEARCH”.

Watching the display, press ui to

call out the desired program type.

Press .

PTY search begins automatically.

b If there is no station broadcasting the

designated program type with the above operation, all the reception bands are searched.

b The station name is displayed on the display

after searching stops.

To continue searching, repeat steps 2 to 4.

b If no station broadcasting the designated program type is found

when all the frequencies have been searched, “NO PROGRAMME” is displayed.

n Radio Text (RT)

RT allows RDS stations to send text messages that appear on the display.

NOTE

The operations described below using will not function in areas in which there are no RDS broadcasts.

0

ENGLISH

Front A Front B

Front A+B

Playing Components

Getting Started

TP Search

Use this function to ﬁnd RDS stations broadcasting trafﬁc programs (TP stations).

Set to “MAIN/TV” and

Press to select “TUNER”.

to “MAIN”.

Front

Press to select “TP SEARCH”.

Press .

TP search begins automatically.

b If no TP station is found with the above

operation, all the reception bands are searched.

b The station name is displayed on the display

after searching stops.

To continue searching, repeat steps

2 to 3.

b If no other TP station is found when all the frequencies have been

searched, “NO PROGRAMME” is displayed.

RT (Radio Text)

“RT” appears on the display when radio text data is received.

Set to “MAIN/TV” and

Press to select “TUNER”.

to “MAIN”.

Press to select “RT”.

b While receiving an RDS broadcast station,

the text data broadcast from the station is displayed.

b To turn the display off, press o p. b If no text data is being broadcast, “NO TEXT

DATA” is displayed.

n To end RDS search / PTY search / TP search / RT

• Do not operate anything for 15 seconds.

• When setting RT, press .

Front

Operations During Playback

Turning Off the Sound Temporarily (Muting)

Press .

The sound is reduced to the level set at menu “Mute Level” (vpage

•

30).

To cancel, press again. Muting can also be canceled by adjusting

• the master volume.

Listening with Headphones

Plug the headphones into the PHONES jack on the main unit.

The sound from the speakers and pre-out connectors is automatically cut.

NOTE

To prevent hearing loss, do not raise the volume level excessively

• when using headphones. Unplug headphones when performing the Audyssey Auto Setup

• procedure or other settings.

Switching the front speakers

Front

Connections Remote Control Information Troubleshooting

Playback

Press .

NOTE

When you set to “Custom” with “Front Speaker Setup“ (vpage 27), you cannot operate .



SpeciﬁcationsMulti-ZoneSettings

ENGLISH

Getting Started Connections Remote Control Information Troubleshooting SpeciﬁcationsMulti-ZoneSettings

Selecting the Surround Mode

Select a surround mode to enjoy surround playback with your favorite sound ﬁeld effects.

q Playing sources according to the sources’ audio signal format/number of channels (Standard Playback)

Operations

The selectable surround modes depend on the following:

• Format of the audio signals being input

Playback

• Number of channels of the audio signals being input

• The set ampliﬁer assignment mode (vpage 25)

Playing the source (vpage 37).

Press to select the surround

mode.

n Multichannel sources

The surround modes that can be selected

differ according to the input source.

n 2-channel sources

When you select “DOLBY PLgz”, set “Amp

Assign” to “Front Height”.

DOLBY PLgx,

DOLBY PLg

DOLBY PLgz

DTS NEO:6

: DOLBY PLgx can be selected when surround back speakers are

being used.

: The signals are decoded in DOLBY PLgx,

DOLBY PLg or DOLBY PLgz, for playback.

: The signals are decoded in DTS NEO:6 for

playback.

Rear



This is the operation for playing 2-channel sources.

Select the mode for the source at “Mode” (

vpage

44).

n DOLBY PLgx, DOLBY PLg

Cinema

Music

Game

Pro Logic

: This mode is suited for movie sources.

: This mode is suited for music sources.

: This mode is suited for games.

: This is the Pro Logic playback mode. This can be

selected when playing with a DOLBY PLg decoder. When this mode is selected, “DOLBY PL” is displayed.

n DTS NEO:6

Cinema

Music

※The modes that can be selected depend on the input source

being played.

The “Cinema” and “Music” modes can also be set by pressing or .

Displaying the currently playing surround mode

: This mode is suited for movie sources.

: This mode is suited for music sources.

nSurround playback of multichannel sources

(Dolby Digital, DTS, etc.)

In the case of standard playback of multi channel sources, the AVR-1910 recognizes the format of the multi-channel audio input signal and automatically operates the appropriate decoder for surround sound.

Input signal

Dolby Digital (other than 2ch)/ Dolby Digital EX

Dolby Digital

DTS

PCM

z1：When a signal is input, the HD AUDIO indicator lights. z2：This is displayed when the input signal is “DTS-ES Matrix 6.1”

z3：This is displayed when the input signal is “DTS-ES Discrete

z4：This is displayed when the input signal is “DTS 96/24”.

Dolby Digital Plus (z1)

Dolby TrueHD (z1)

DTS (5.1ch)/ DTS-ES Discrete 6.1 / DTS-ES Matrix 6.1 / DTS 96/24

DTS-HD (z1)

PCM (multi ch)

and the AVR-1910’s “AFDM” setting (vpage 45) is set to “ON”.

6.1”.

The indication contents of

the display

DOLBY DIGITAL DOLBY DIGITAL EX DOLBY DIGITAL+PLgx CINEMA DOLBY DIGITAL+PLgx MUSIC DOLBY DIGITAL+PLgz DOLBY DIGITAL++PLgx C DOLBY DIGITAL++PLgx M DOLBY DIGITAL++PLgz DOLBY TrueHD DOLBY HD+EX DOLBY HD+PLgx CINEMA DOLBY HD+PLgx MUSIC DOLBY HD+PLgz DTS SURROUND DTS+PLgx CINEMA DTS+PLgx MUSIC DTS+PLgz DTS+NEO:6 DTS ES MTRX6.1 (z2) DTS ES DSCRT6.1 (z3) DTS 96/24 (z4) DTS-HD HI RES DTS-HD MSTR DTS-HD+NEO:6 DTS-HD+PLgx CINEMA DTS-HD+PLgx MUSIC DTS-HD+PLgz MULTI CH IN MULTI IN+PLgx CINEMA MULTI IN+PLgx MUSIC MULTI IN+PLgz MULTI CH IN 7.1

2

ENGLISH

Selecting the Surround Mode

Getting Started

w Playing in a DENON original surround

Selecting the Surround Mode

mode

The desired mode according to the program source and viewing situation can be selected from among 7 DENON original surround modes.

Select the input source by pressing

and play the source (vpage

37).

Press to select the Surround

mode.

5CH/7CH STEREO

ROCK ARENA

JAZZ CLUB

MONO MOVIE

VIDEO GAME

MATRIX

VIRTUAL

z1： When playing sources recorded in monaural in the MONO

MOVIE mode, the sound will be off balance with a single channel (left or right), so input to both channels.

Depending on the program source being played, it may not be possible to achieve a satisfactory surround effect. In this case, try other modes to achieve a sound ﬁeld suited to your tastes.

NOTE

When the input signal is DOLBY TrueHD, DOLBY DIGITAL Plus,DTSHD you cannot select DENON original surround mode.

： This mode is for enjoying stereo sound from all

speakers.

： This mode is for enjoying the atmosphere of a

live concert in an arena.

： This mode is for enjoying the atmosphere of a

live concert in a jazz club.

： This mode is for playing monaural movie

sources with surround sound.

： This mode is suited for achieving surround

sound with video games.

： This mode lets you add a sense of expansion

to stereo music sources.

： This mode is for enjoying surround effects

using only the front speakers or headphones.

Front

Rear

e Direct Playback

In this mode the signals bypass the tone adjustment circuitry for high quality sound. The sound is output to the same channels as the input signal.

Select the input source by pressing

and play the source (vpage

Front

37).

Press to select the “DIRECT”.

Rear

Displaying the currently playing surround mode

Input signal

Analog signal /

PCM (2ch) /

Dolby Digital source /

DTS source /

Other 2-channel digital signals

PCM (multi ch)

The indication contents of the

display

DIRECT

MULTI CH DIRECT M DIRECT + PLgx CINEMA M DIRECT + PLgx MUSIC M DIRECT + PLgz M DIRECT 7.1

r Stereo Playback

This is the mode for playing in stereo. The tone can be adjusted. Sound is output from the front left and right speakers and subwoofer.

Select the input source by pressing

and play the source (vpage

Front

37).

Press to select the “STEREO”.

Rear

t Playing the Pure Direct mode

This is the mode that recreates the original sound most faithfully, providing extremely high quality sound.

Select the input source by pressing

and play the source (vpage

37).

Press .

Front

Rear

To cancel, press again.

• The channel level and surround parameters in the PURE DIRECT

• mode are the same as in the DIRECT mode.

NOTE

When in the PURE DIRECT mode, the on-screen display is not displayed and the display on the main unit is turned off.

Connections Remote Control Information Troubleshooting

Playback

SpeciﬁcationsMulti-ZoneSettings





Getting Started Connections Remote Control Information Troubleshooting Speciﬁ cations

ENGLISH

Multi-ZoneSettings

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu

Remote control

operation buttons

Displaying the menu

Cancel the menu

Playback

The sound being played in the surround mode can be adjusted to your liking. The items (parameters) that can be adjusted depend on the signal being input and the currently set surround mode. For details on the adjustable parameters, see “Surround Modes and Parameters” (vpage 57).

NOTE

Some of the setting items cannot be set while playback is stopped. Set these items during playback.

Setting items Setting contents

Mode

Set the play mode for playing 2-channel sources in surround.

n In the PLgx, PLg or PLgz mode

Cinema : This is the mode for cinema source. Music : This is the mode for music source. Game : This is the mode for game source. ProLogic : Dolby Pro Logic playback mode (PLg mode only). (This is

the mode for 4-channel playback (front L, front R, center, surround (MONO).)

n In the DTS NEO:6 mode

Cinema : This is the mode for cinema source. Music : This is the mode for music source.

• The “Music” mode is also effective for movie sources including a lot of stereo music.

• The “Cinema” and “Music” modes can also be set by pressing

or .

Cinema EQ

Soften the treble range of movie sound tracks for better understanding.

OFF : “Cinema EQ” is not used. ON : “Cinema EQ” is used.

Dynamic Range Compression (D.Comp)

Compress dynamic range (difference between loud and soft sounds).

Low/Mid/High : These set the compression level. OFF : Turn dynamic range compression off.

The “D.Comp” indicator lights when playing DTS source that supports

the “D.Comp” function.

Dynamic Range Control (DRC)

Compress dynamic range.

Auto : Dynamic range compression of Dolby TrueHD sources turns on and off automatically.

Low/Mid/High : These set the compression level. OFF : Turn dynamic range compression off.

Adjusting the sound ﬁ eld effects (Surround Parameter)

Default settings are underlined.

Adjusting the Sound Field Effects (Parameter)

Setting items Setting contents

LFE

Adjust the low-frequency effects level (LFE).

–10dB ~ 0dB

For proper playback of the different program sources, we recommend

setting to the values below.

• Dolby Digital sources : “0dB”

• DTS movie sources : “0dB”

• DTS music sources : “–10dB”

Center Image

Assign center channel signal to front left and right channels for wider sound.

0.0 ~ 1.0 (0.3)

Panorama

Assign front L/R signal also to surround channels, for wider sound.

ON : Set. OFF : Do not set.

Dimension

Shift sound image center to front or rear, to adjust playback balance.

0 ~ 6 (3)

Center Width

Assign center channel signal to front left and right channels for wider sound.

0 ~ 7 (3)

Delay Time

Adjust delay time to control sound stage size.

0ms ~ 300ms (30ms)

Effect Level

Adjust the strength of the surround effect.

1 ~ 15 (10)

Set to a lower level if the positioning and sense of phase of the

surround signals seems unnatural.

Room Size

Determine size of acoustic environment.

NOTE

“Room Size” does not indicate the size of the room in which sources are played.

Small : Simulate acoustics of a small room. Medium small : Simulate acoustics of a medium-small room. Medium : Simulate acoustics of a medium room. Medium large : Simulate acoustics of a medium-large room. Large : Simulate acoustics of a large room.

ENGLISH

Adjusting the Sound Field Effect (Parameter)

Getting Started

Setting items Setting contents

AFDM (Auto Flag Detect Mode)

Detects the source’s surround back channel signal and sets the optimum surround mode automatically.

Surround Back

Sets the method of generating of the surround back channel.

ON : Set. OFF : Do not set.

n For 2-channel sources

ON : The surround back channel is used. OFF : No signal is played from the surround back channels.

n For multi channel sources

Set this to set the method of generating of the surround back channel for sources that do not include surround back signals and when you do not want to play the surround back signals included in the source. Check the audio signals of the source being played before making this setting.

OFF : No signal is played from the surround back channels. MTRX ON : Generate and play the surround back signals from the

surround channel signals.

PLgx CINEMAz1 : Generate and play the surround back signals by

decoding the signals in the “Dolby Pro Logic gx Cinema” mode.

PLgx MUSICz2 : Generate and play the surround back signals by

decoding the signals in the “Dolby Pro Logic gx Music” mode. ES MTRX : Generate and play the surround back signals from the surround channel signals of the DTS source. ES DSCRTz3 : Play the surround back signals included in the 6.1- channel DTS source. DSCRT ONz3 : Play the surround back signals included in the 7.1- channel source.

1 : This can be selected when “S.Back” in the “Speaker Conﬁg.”

settings (vpage 26) is set to “2sp”.

2 : This can be selected when “S.Back” in the “Speaker Conﬁg.”

settings (vpage 26) is set to “2sp” or “1sp”.

3 : When “AFDM” is set to “ON”, the surround back channel is played

with the AFDM function. When selected while “AFDM” is set to “OFF”, the source’s surround back signals are played.

This can also be set by pressing .

NOTE

This is valid when the “Amp Assign” setting (vpage 25) is set to “7.1channel surround back” or “6.1-channel surround back”, and when the “S.Back” setting (vpage 26) is set to “Large” or “Small”.

Setting items Setting contents

Front Height

Set whether or not to use the front height channel.

Subwoofer ATT

Attenuate subwoofer level when using EXT. IN mode.

Subwoofer

Turn subwoofer output on and off.

Default

Restores all the surround parameter settings to their defaults.

ON : Use the front height channel. OFF : Do not use the front height channel.

This can also be set by pressing

ON : The input from the subwoofer channel is attenuated. OFF : The input from the subwoofer channel is not attenuated. Usually use

in this mode.

Set this to “ON” if the subwoofer channel level seems too high when

playing audio signal.

ON : The subwoofer is used. OFF : The subwoofer is not used.

Yes : Reset to the defaults. No : Do not reset to the defaults.

Adjusting the tone (Tone Control)

Setting items Setting contents

Tone Control

Sets the tone control function ON and OFF.

This can be set when “Dynamic EQ” (vpage

46) is set to “OFF”.

Bass

Adjusts the low frequencies.

This can be set when “Tone Control” is set to “ON”.

Treble

Adjusts the high frequencies.

This can be set when “Tone Control” is set to “ON”.

ON : Allow tone adjustment (treble, bass). OFF : Playback without tone adjustment.

The tone cannot be adjusted when in the DIRECT mode.

–6dB ~ +6dB (0dB)

Default settings are underlined.

Connections Remote Control Information Troubleshooting

Playback

Multi-ZoneSettings

Speciﬁcations

Remote control

operation buttons

Displaying the menu

: Cancel the menu

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu



ENGLISH

Dynamic EQ : ON/Volume : OFF

“Green” “OFF”

Dynamic EQ / Volume : OFF

Dynamic EQ / Volume : ON

“Green” “Red”

Dynamic EQ : ON / Volume : OFF

Getting Started Connections Remote Control Information Troubleshooting Speciﬁcations

Adjusting the Sound Field Effect (Parameter)

Making the MultEQ, Dynamic EQ and Dynamic Volume settings (Audyssey Settings)

Default settings are underlined.

• When the “Audyssey Auto Setup” (vpage 20) procedure is performed, the “MultEQ”, “Dynamic EQ” and “Dynamic Volume” functions are enabled.

• Operating conditions for each function

• Dynamic EQ :

When “MultEQ” is set to “ON”

• Dynamic Volume :

When “Dynamic EQ” is set to “ON”

Playback

• Setting :

When “Dynamic Volume” is set to “ON”

Multi-ZoneSettings

NOTE

If the speaker settings are changed after the “Audyssey Auto Setup” procedure is performed, “MultEQ”, “Dynamic EQ” and “Dynamic Volume” functions cannot be selected and “Run Audyssey” is displayed. If this happens, either perform the “Audyssey Auto Setup” procedure again, or perform the “Restore” operation (vpage 24) to restore the settings to as they were after the “Audyssey Auto Setup” procedure was performed.

Setting items Setting contents

MultEQ

Corrects the frequency response of the different speakers.

NOTE

• “MultEQ” and “Manual EQ” settings for which “Not Used” has been set at “EQ Customize” (vpage

29) cannot be selected.

• When using headphones, “MultEQ” is set to “OFF”.

Audyssey : Optimize frequency response of all speakers. Audyssey Byp.L/R : Optimize frequency response of speakers except

front L and R speakers. Audyssey Flat : Optimize frequency response of all speakers to ﬂat response.

Manual : Apply frequency response set with “Manual EQ” (vpage 47). OFF : The “MultEQ” equalizer cannot be used.

• When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected, “ ” lights.

• After running Audyssey Auto Setup, if the Speaker Conﬁguration, Distance, Channel Level, and Crossover Frequency have changed without increasing the number of speakers measured, only “

” lights.

• This can also be set by pressing .

MultEQ

Dynamic EQ

Dynamic Volume

Setting

Setting items Setting contents

Dynamic EQ

Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics.

This can be set when the “MultEQ” (vpage 46) is set to anything other than “OFF”.

ON : Use Dynamic EQ function. OFF : Do not use Dynamic EQ function.

• When set to “ON”, “ ” is displayed.

• When “MultEQ” is set to “OFF”, “Dynamic EQ” is automatically set

to “OFF”

• This can also be set by pressing .

“Red” “Off”

NOTE

“Tone Control” is set to “OFF” when “Dynamic EQ” is set to “ON”. Reference Level Offset : Audyssey Dynamic EQ takes the standard ﬁlm

mixing level of 85 dB SPL during –20 dB FS input as its reference level. However, since standardization is lacking outside the ﬁlm industry, the reference level of media contents may not be appropriate. In order to view such contents, Reference Level Offset of Dynamic EQ has available offsets of 5 dB, 10 dB and 15 dB.

0dB : Suitable for viewing movies.

•

5dB : Suitable for listening to classical music and other content mixed

• at a high level. 10dB : Suitable for listening to jazz and other audio sources with a wide

• dynamic range. Also suitable for viewing TV. 15dB : Suitable for listening to pop, rock music and other content with an

• extremely wide dynamic range.

Setting is enabled when “Dynamic EQ” is “ON” .

Dynamic Volume

Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies.

ON : Use Dynamic Volume. The Dynamic Volume effect will be at the level of the “Setting” (vpage 47) OFF : Do not use Dynamic Volume.

• When set to “ON”, “ ” is displayed.

• When “MultEQ” is set to “OFF”, “Dynamic Volume” is automatically

set to “OFF”.

• This can also be set by pressing .



Remote control

operation buttons

Displaying the menu

: Cancel the menu

This can be set when “Dynamic EQ” (vpage

46) is set to “ON”.

: Moves the cursor (Up/Down/Left/Right)

“Green” “Red”

: Decision the setting

: Return to previous menu

ENGLISH

OFF Mode 1

(RESTORER 64)

Mode 2

(RESTORER 96)

Mode 3

(RESTORER HQ)

Adjusting the Sound Field Effect (Parameter)

Getting Started

Setting items Setting contents

Setting

Set Dynamic Volume effect.

This can be set when “Dynamic EQ” (vpage

46) is set to “ON”.

Day : Low setting provides the least adjustments to the loudest and softest of sounds. Evening : Middle setting prevents loud and soft sounds from being much louder and softer respectively than average sounds. Midnight : High setting affects volume the most, causing all sounds to be of equal loudness.

Adjust tonal quality for each speaker using graphic equalizer (Manual EQ)

Default settings are underlined.

Setting items Setting contents

Adjust CH

Adjust the tonal quality of the individual speakers.

Base Curve Copy

Copy the MultEQ “Audyssey Flat” correction curve.

Default

Reset the “Manual EQ” settings to their defaults.

1. Select speaker adjustment method. All CH : Adjust tonal quality for all speakers together. L/R CH : Adjust tonal quality for each L/R speaker pair. Each CH : Adjust tonal quality for each speaker separately.

2. Select the frequency band to be adjusted. 63Hz / 125Hz / 250Hz / 500Hz / 1kHz / 2kHz / 4kHz / 8kHz / 16kHz

b When “L/R CH” or “Each CH” is selected, select the speaker to be

adjusted.

3. Adjust the level. –20.0dB ~ +6.0dB (0dB)

Yes : Copy. No : Do not copy.

“Base Curve Copy” is displayed after the Audyssey Auto Setup

procedure has been performed.

Yes : Reset to the defaults. No : Do not reset to the defaults.

Restoring compressed audio to nearly pre-compressed conditions for playback (RESTORER)

Default settings are underlined.

• Such compressed audio formats as MP3, WMA (Windows Media Audio) and MPEG-4 AAC reduce the amount of data by eliminating signal components that are hard for the human ear to hear. The RESTORER function generates the signals eliminated upon compression, restoring the sound to conditions near those of the original sound before compression. It also corrects the sense of volume of the bass to obtain richer sound with compressed audio signals.

• This can be set with analog signals or when a PCM signal (fs = 44.1/48 kHz) is input.

Setting contents

OFF : Do not use RESTORER. Mode1 (RESTORER 64) : Optimized mode for compressed sources with very weak highs. Mode2 (RESTORER 96) : Apply suitable bass and treble boost for all compressed sources. Mode3 (RESTORER HQ) : Optimized mode for compressed sources with normal highs.

• The default setting for “iPod” is “Mode3”. All others are set to “OFF”.

• When set to something other than “OFF”, “ ” is displayed.

• This can also be set by pressing during playback.

Adjusting the audio delay time while watching the picture (Audio Delay)

Default settings are underlined.

Setting contents

0ms ~ 200ms

• If you wish to adjust the “Audio Delay” while playing HDMI or component video signals, press u

to set “OSD” to “OFF”. This way the audio delay can be adjusted while watching the picture. (Press

u again. The display switches to the display of the menu screen only.)

• This cannot be adjusted when playing in the EXT. IN, DIRECT or STEREO mode (with “Front Speaker” set to “Large”, “Tone Control” to “OFF” and “MultEQ” and “RESTORER” to “OFF”).

• When the Auto Lipsync Correction function is operating, you can set within the range 0 ~ 100 ms.

• Store “Audio Delay” for each input source.

Connections Remote Control Information Troubleshooting

Playback

Multi-ZoneSettings

Speciﬁcations

Remote control

operation buttons

Displaying the menu

: Cancel the menu

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu



8

Getting Started Connections Remote Control Information Troubleshooting Speciﬁ cations

ENGLISH

Multi-ZoneSettings

Checking the Status (Information)

Setting items Setting contents

Status

Shows information about current settings.

Select Source / Surround Mode / Input Mode / Decode Mode / HDMI / Digital / Component / iPod Dock / Video Select / Source Level / i/p Scaler / Resolution / Progressive Mode / Aspect

You can also display current status on the main unit’s display each time you press on the main unit.

ZONE2

POWER / Select Source / Master Volume•

Audio Input Signal

Shows information about audio input signals.

Surround Mode : The currently set surround mode is displayed. Signal : The input signal type is displayed. fs : The input signal’s sampling frequency is displayed. Format : The number of channels in the input signal (front, surround, LFE)

is displayed.

Offset : The dialogue normalization correction value is displayed. Flag : This is displayed when inputting signals including a surround back

channel. “MATRIX” is displayed with Dolby Digital EX and DTS-ES Matrix signals, “DISCRETE” with DTS-ES Discrete signals.

HDMI Information

Shows information about HDMI input signals and monitor.

HDMI Signal Information

Resolution / Color Space / Pixel Depth •

HDMI Monitor Information

Interface / Suport Resolution •

Auto Surround Mode

Shows information about auto surround mode settings.

Analog /PCM / Digital 2ch / Digital 5.1ch / Multi CH

Quick Select

Shows information about quick select settings.

Quick Select 1 / Quick Select 2 / Quick Select 3

Name / Input Source / Video Select / Volume Level / MultEQ / Dynamic EQ / Dynamic Vol / Front SP / Analog/PCM / Digital 2ch / Digital 5.1ch / Multi CH

•

ZONE2 Quick Select Quick Select 1 Source / Quick Select 1 Volume / Quick Select 1 Name Quick Select 2 Source / Quick Select 2 Volume / Quick Select 2 Name Quick Select 3 Source / Quick Select 3 Volume / Quick Select 3 Name

Preset Channel

Shows information about preset channels.

A 1 ~ G 8

TUNER•

Playback



ENGLISH

Getting Started

Connections Remote Control Information Troubleshooting

Speciﬁ cationsMulti-ZoneSettings

Playback

Turn the power on for all the equipment connected by

HDMI cable.

Set the HDMI control function for all equipment

connected by HDMI cable.

Set “HDMI Control” (vpage 28) to “ON“.

b Please refer to the owner’s manual as regards setting of connected

devices.

b Carry out Steps 1 and 2 should any of the equipment be

unplugged.

Switch the television input to the HDMI connected to

the AVR-1910.

Switch the AVR-1910 input to the HDMI input source

and check if the picture from the player is ok.

When you turn the TV’s power to standby, check that

the power of the AVR-1910 and player also goes on standby.

If the HDMI control function does not operate properly, check the following points.

• Is the TV or player compatible with the HDMI control function?

• Is the AVR-1910 properly set?

• Is “HDMI Control” (vpage 28) set to “ON”?

• Is “Power Off Control” (vpage 28) set to “ON”?

• Are the HDMI control function settings of all equipment correct?

NOTE

Should any of the operations below be performed, the interlocking function may be reset, in which case, repeat step’s 1 and 2.

Menu “HDMI” (vpage 28) setting has changed. There is a change to the connection between the equipment and the HDMI, or an increase in equipment.

•

NOTE

• When you power off AVR-1910, the HDMI control function does not operate.

• Some functions may not operate depending on the connected TV or player. Check the owner’s manual of each device for details beforehand.

• When “HDMI Control” is set to “ON”, it is not possible to assign an HDMI terminal to “TV” at “HDMI” (vpage 28).

• When “HDMI Control” (vpage 28) is set to “ON”, power is supplied constantly to the AC outlet (UNSWITCHED).

Convenient functions

When you make an HDMI connection with a TV or player compatible with AVR-1910 and HDMI control functions, you can perform the following operations by setting the HDMI control function of each device.

Press and display the time you want to set.

The “SLEEP” indicator on the display lights.

• The time switches as shown below each time is pressed.

Sleep:OFF Sleep:120min

Sleep:30min Sleep:60min

Sleep:90min

• The time display turns off after about 5 seconds, and the setting is activated.

• Once the set time has passed, the power is automatically set to standby.

This function allows you to automatically set the power to standby after the set amount of time has passed. When the sleep timer turns the power off in the MAIN ZONE, the power also turns off in the ZONE2.

HDMI Control Function

Setting the power to standby after a certain amount of time (Sleep Timer Function)

n To cancel the sleep timer

Press to set “OFF”.

• The “SLEEP” indicator on the display turns off.

• To play the TV’s sound on the AVR-1910, make optical digital connections (vpage 13 “Connecting the TV”).

• To use this function, set “HDMI Control” (vpage 28) to “ON”.

Rear

n AVR-1910 power off can be linked to the TV power

off step

zWhen you set “Output audio from amp” in the TV audio

output setup operation, you can switch the amp power on.

n You can switch audio output devices with a TV

operation

n You can adjust AVR-1910 volume in the TV volume

adjustment operation

n You can switch AVR-1910 input source through

linkage to TV input switching

n When playing the player, the AVR-1910 input

function switches to the function of that player

ENGLISH

Channel Volume

FL 0.0dB SR 0.0dB

C 0.0dB SBR 0.0dB FR 0.0dB SBL 0.0dB SW 0.0dB SL 0.0dB

Fader FRONT : REAR [ ]:CH Sel.

Getting Started Connections Remote Control Information Troubleshooting SpeciﬁcationsSettings Multi-Zone

Adjust the volume of the different speakers

You can adjust the channel level either according to the playback sources or to suit your taste, as described below.

Adjust the volume of the different speakers

Press .

Playback

Saving frequently used settings (Quick Select Function)

This function allows you to save all the settings shown in step

1. When frequently used settings are saved, they can easily be set again the next time you want to use them. This function also allows you to always enjoy the same playback environment.

• Three sets of settings can be saved.

MAIN ZONE settings

Saving the settings

n Naming Quick Select settings

“Quick Select Name” (vpage 31).

ZONE2 settings

It is also possible to save three settings for ZONE2.

Saving the settings

Set the remote control unit’s

device selector switches as shown on right.

Front

Press ui to select the speaker.

The speaker that can be set switches each

time one of the buttons is pressed.

Press o p to adjust the volume.

b In the case of a subwoofer, reducing the volume when it is at

“–12 dB” will change the setting to “OFF” (none).

If headphones are plugged in, the headphones settings screen appears.

Adjusting the volume of groups of speakers (Fader Function)

This function lets you adjust (fade) the sound from all the front (Front speaker / center speaker / Front Height speaker) or rear (Surround speaker / Surround Back speaker) speakers at once.

Use or i to select “Fader”, then select the item

to be adjusting using o or p.

Press o p to adjust the volume of the speakers.

Set the items below to the settings you want to save.

q Input source (vpage 37)

w Input Mode (vpage 34) e Surround Mode (vpage 42) r Audyssey Settings (MultEQ, Dynamic EQ, Dynamic

Volume) (vpage 46) t Front Speaker Setup (vpage 27) y Volume setting (vpage 37) u Video Select (vpage 34)

Press and hold the desired

appears on the display.

The current settings will be memorized.

Quick Select 1 DVD –40 dB Quick Select 2 SAT/CBL –40 dB Quick Select 3 VCR/iPod –40 dB

Calling the settings out

Press the at which the settings you want to call out are saved.

until “Memory”

GQuick Select DefaultsH

Input Source Volume

Front

 Perform steps 1 and 2 under “MAIN ZONE

settings”.

Various memory functions

Personal Memory Plus Function

This function sets the settings (input mode, surround mode, MultEQ, Dynamic EQ, Dynamic Volume, audio delay etc.) last selected for the individual input sources.

Last Function Memory

This stores the settings as they were directly before the standby mode was set. When the power is turned back on, the settings are restored to as they were directly before the standby mode was set.

Backup Memory

The various settings are backed up for about 1 week, even if the power is turned off or the power cord is disconnected.

• The fader function does not affect the subwoofer.

• The fader can be adjusted until the volume of the speaker adjusted to the lowest value is –12 dB.

0

NOTE

Input sources stored with the quick select function cannot be selected if they have been deleted at menu “Source Delete” (vpage 30). In this case, store them again.

Playing 2-Channel Sound in ZONE2 (Multizone function)

w q w q

(L) (R)

"69

ENGLISH

Getting Started

2-channel sound can be played in rooms other than the MAIN ZONE where multichannel sound is played. There are two methods to do this, as described below. Choose one of the methods.

q ZONE2 playback by speaker output wZONE2 playback by audio output (PRE OUT) (using an

external amplifier)

q ZONE2 playback by speaker output

With the Amp Assign function, Zone 2 audio signals are output from the AVR-1910's SURR BACK/AMP ASSIGN terminals.

Preparations

Connecting and setting the speakers

Connecting the speakersn

w ZONE2 playback by audio output

The audio signals connected to the AVR-1910’s ZONE2 output terminals (ZONE2 OUT) are output to the ZONE2’s ampliﬁer and played with that ampliﬁer.

Connection (ZONE2)

MAIN ZONE

AVR-1910

ZONE2

Playback

The operation is the same for “q ZONE2 playback by speaker output” and “w ZONE2 playback by audio output”.

Set the remote control unit’s

“device selector switches” as shown on right.

 Turn on the AVR-1910’s power.

 (vpage 17“Turning the Power On”)

 Press to turn on the ZONE2 power.

When the power turns on, the “ ” indicator lights on the

display.

b The power can be turned on by pressing the one of

while in the standby mode.

 Use the input source selector to choose the input

source.

The selected input source is shown on the display.

NOTE

When “SOURCE” is selected for the input source, the sound being played in the MAIN ZONE is played. No sound is output if a digital audio input source is being played in the MAIN ZONE.

Rear

Connections Playback Information Troubleshooting

Multi-Zone

Remote Control

Necessary settings

Set the AMP ASSIGN mode to “ZONE2”.

•

“AMP Assign” (vpage 25) Perform the settings at “ZONE2 Setup”.

•

“Making the ZONE2 settings” (vpage 30)

Adjust the volume on the connected ampliﬁer.

• Also be sure to read the operating instructions of the connected

• devices.

NOTE

• We recommend using high quality pin-plug cables for audio connections in order to prevent noise.

• It is not possible to play the digital audio signals input from the HDMI, COAXIAL or OPTICAL terminals in ZONE2. Play using analog connections (in stereo).

Adjusting the volume (for “q ZONE2 playback by speaker output”)

Use

GVariable rangeH

b The volume can be adjusted up to the level set at “Vol. Limit”

b The volume display is the display set at “Volume Display”

For “w ZONE2 playback by audio output”, adjust the volume on the connected ampliﬁer.

to adjust the volume.

– – – –80dB(1)

(vpage 30).

–40dB(41)

+18dB(99)



SpeciﬁcationsSettings

ENGLISH

Getting Started Connections Playback Information Troubleshooting SpeciﬁcationsMulti-ZoneSettings Remote Control

Operating the Connected Devices by Remote Control Unit

Registering Preset Codes

DENON and other makes of components can be operated by setting the preset memory.

Switch .

MAIN/TV

DEVICE

Set to the component to be registered.

DVD/HDP

DVR/VCR

SAT/CBL

Press and at the same

time.

The indicator starts ﬂashing.

Press ~ and input the 3-

digit number of the brand of the component to be preset. The numbers are shown in the Preset Code Table

(vEnd of this manual).

To store the codes of another component in the

memory, repeat steps 1 to 4.

: To register a TV

: To operate a Blu-ray disc player, DVD player,

Digital video recorder, video deck, satellite receiver, cable TV or CD player

: TV

: DVD player or Blu-ray disc player

: Digital video recorder or video deck

: Satellite receiver or cable TV

: CD player

Rear

Operating Registered Devices

Switch .

MAIN/TV

DEVICE

: To operate the TV or iPod

: To operate a Blu-ray disc player, DVD player,

Digital video recorder, video deck, satellite receiver, cable TV or CD player

Set to the component you want to operate.

MAIN

DVD/HDP

DVR/VCR

SAT/CBL

Operate the component.

: iPod

: TV

: DVD player or Blu-ray disc player

: Digital video recorder or video deck

: Satellite receiver or cable TV

: CD player

b For details, refer to the component’s operating instructions.

NOTE

Depending on the model and year of manufacture, this function cannot be used for some models, even if they are of makes listed in the list of preset codes.

iPod

Front

DEVICE SELECT

1 2

MEMORY

TU/PAGE

8 9

uio p

ENTER Enter

RETURN Return

1 : This operation is possible when using a

DENON ASD-3N or ASD-3W Control Dock for iPod.

2 : This operation is possible when using a

DENON ASD-1R or ASD-11R Control Dock for iPod.

Browse/Remote mode switching

Play / Pause

Stop

Memoryz1

Page up/downz1

Auto search

(cue)

Cursor

Pause

Press and

hold

Once

Page search

mode switching

• Some manufacturers use more than one type of remote control code. Refer to the included list of preset codes to change the number and verify correct operation.

• VDP (Video Disc Player) can be preset when is set to “DVD/ HDP”.

• The preset memory can be set for one component only among the following: DVD/HDP, DVR/VCR and SAT/CABLE.

2

Blu-ray Disc / DVD Player

Operating Registered Devices

Digital Video Recorder / Video Deck

ENGLISH

Getting Started

Front

DEVICE SELECT

ON/SOURCE Power on / Standby

1 Play

3 Pause 2 Stop

6 7

CH + –

TV INPUT Switching the input

VOLUME df

MUTE TV mute

MENU Calling out the menus

Front Front Front

uio p

ENTER Enter setting SETUP Setup

RETURN Return

(fast-reverse / fast-forward)

Manual search

Channel

d : TV Volume (+) f : TV Volume (–)

Cursor operation

Rear

1 ~ 12 Channels

Defau

lt setting

(Preset code)

Special Remarks

: When the punch through function

(vpage 54) is set, this functions as the button for the device for which punch through is set.

HITACHI

(014)

Front

DEVICE SELECT

POWER OFF Power off ON/SOURCE Power on or Power on / Standby

1 2

SHIFT, 3

BD Player DVD Player

SKIP +

6 7

8 9

MENU Calling out the menus

uio p

ENTER Enter setting SETUP Setup

RETURN Return

SOURCE SELECT /

TOP MENU

(fast-reverse / fast-forward)

Calling out the top menus

Play

Stop

Pause

– Disc skip

Manual search

Auto search (cue)

Cursor operation

Rear

0 ~ 9, +10 Number input / Track selection

Defau

lt setting

(Preset code)

Special Remarks

＊ : The initial setting of Preset code is 111 (DVD Player).

BD Player DVD Player

DENON

(121)

q, w

DENON

＊

(111)

Front

DEVICE SELECT

ON/SOURCE Power on / Standby

SHIFT, 3

6 7

CH + – MENU Calling out the menus

uio p

ENTER Enter setting SETUP Setup

RETURN Return

(fast-reverse / fast-forward)

Play Stop

Pause

Manual search

Switch

channels (+, –)

Cursor operation

Rear

0 ~ 9, +10

Defau

lt setting

(Preset code)

Special Remarks

hannel

HITACHI

(008)

q, w

Connections Playback Information Troubleshooting

Remote Control

SpeciﬁcationsMulti-ZoneSettings

Rear Rear Rear

【Special Remarks】

q Only one device can be set in the preset memory for each mode. When a new preset code is registered, the existing code is automatically erased.

w For some brands, the DVD remote control buttons may have different function names.

Check beforehand.



ENGLISH

Getting Started Connections Playback Troubleshooting SpeciﬁcationsMulti-ZoneSettings Information

Satellite receiver/Cable TV

Remote Control

Front Front

Front

DEVICE SELECT

ON/SOURCE Power on / Standby

1 Play 3 Pause 2 Stop

6 7

CH + –

uio p

ENTER Enter setting

MENU SETUP

RETURN Return

(fast-reverse / fast-forward)

Calling out the menus

Manual search

Channel

Cursor operation

Setup

Rear

0 ~ 9, +10 Channels

Satellite

Defau

lt setting

(Preset code)

Special Remarks

: When the punch through function

(vpage 54) is set, this functions as the button for the device for which punch through is set.

Receiver

–

Cable TV

ABC

(009)

Operating Registered Devices

CD Player

Front

DEVICE SELECT

POWER OFF Power off

ON/SOURCE Power on or Power on / Standby

1 2

SHIFT, 3

SKIP + Disc skip +

6 7

8 9

(fast-reverse / fast-forward)

Rear

0 ~ 9, +10 Number input / Track selection

Defau

lt setting

(Preset code)

Special Remarks

Play

Stop

Pause

Manual search

Auto search (cue)

DENON

(111)

Assigning buttons that are Not Used to Operate Other Devices (Punch Through Function)

The Blu-ray disc Player/DVD player, Digital Video recorder, video deck, or CD player can be operated as described below even when is set to the “SAT/CBL” or “TV” position.

• Play • Stop • Pause

• fast-forward • fast-reverse • Auto Search

Switch .

MAIN/TV

DEVICE

Switch .

SAT/CBL

Press and at the same time.

The indicator starts ﬂashing.

Refer to the table below and input the number

corresponding to the device to be assigned.

iPod, Tuner

CD Player

: Assigning TV buttons to operate other devices

: Assigning satellite receiver or cable TV buttons to

operate other devices

: Assigning TV buttons to operate other devices

: Assigning satellite receiver or cable TV buttons to

operate other devices

Device to be assigned Numbers

Rear

Rear Rear

【Special Remarks】

q Only one device can be set in the preset memory for each mode. When a new preset code is registered, the existing code is automatically erased.

w For some brands, the DVD remote control buttons may have different function names.

Check beforehand.



Blu-ray Disc Player / DVD Player

Digital Video Recorder, Video Deck

No setting

This is set to “No setting” upon purchase.

Other Information

ENGLISH

Getting Started

Surround

The AVR-1910 is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same sense of presence as in a movie theater.

Dolby Surround

Dolby Digital

Dolby Digital is a multichannel digital signal format developed by Dolby Laboratories. A total of 5.1-channels are played: 3 front channels (“FL” , “FR” and “C”), 2 surround channels (“SL” and “SR”) and the “LFE” channel for low frequencies. Because of this, there is no crosstalk between channels and a realistic sound ﬁeld with a “three-dimensional” feeling (sense of distance, movement and positioning) is achieved. A real, overpowering sense of presence is achieved when playing movie sources in AV rooms as well.

Dolby Digital Plus

Dolby Digital Plus is an improved Dolby Digital signal format that is compatible with up to 7.1-channels of discrete digital sound and also improves sound quality thanks to extra data bit rate performance. It is upwardly compatible with conventional Dolby Digital, so it offers greater ﬂexibility in response to the source signal and the conditions of the playback equipment.

Dolby TrueHD

Dolby TrueHD is a high deﬁnition audio technology developed by Dolby Laboratories, using lossless coding technology to faithfully reproduce the sound of the studio master. This format is compatible with a maximum sampling frequency of 96 kHz and up to 7.1-channels, so it is used for applications particularly prioritizing sound quality.

Dolby Pro Logic g

Dolby Pro Logic g is a matrix decoding technology developed by Dolby Laboratories. Regular music such as that on CDs is encoded into 5-channels to achieve an excellent surround effect. The surround channel signals are converted into stereo and full band signals (with a frequency response of 20 Hz to 20 kHz or greater) to create a “three-dimensional” sound image offering a rich sense of presence for all stereo sources.

Dolby Pro Logic gx

Dolby Pro Logic gx is a further improved version of the Dolby Pro Logic g matrix decoding technology.

Audio signals recorded in 2-channels are decoded to achieve a natural sound with up to 7.1-channels. There are 3 modes: “Music” suited for playing music, “Cinema” suited for playing movies, and “Game” which is optimized for playing games.

Dolby Digital EX

Dolby Digital EX is a 6.1-channel surround format proposed by Dolby Laboratories that allows users to enjoy in their homes the “DOLBY DIGITAL SURROUND EX” audio format jointly developed by Dolby Laboratories and Lucas Films. The 6.1 channels of sound, including surround back channels, provide improved sound positioning and expression of space.

Dolby Pro Logic gz

Dolby Pro Logic gz introduces a new dimension to Home Entertainment through the addition of a pair of front height channels. Compatible with stereo, 5.1 and 7.1 content, Dolby Pro Logic gz provides enhanced spaciousness, depth and dimension to movies, concert video and videogame playback while maintaining the full integrity of the source mix.

Dolby Pro Logic gz identiﬁes and decodes spatial cues that occur naturally in all content, directing this information to the front height channels, complementing the performance of left and right surround sound speakers. Content that is encoded with Dolby Pro Logic gz height channel information can be even more revealing, with perceptually discrete height channel information bringing an exciting new dimension to home entertainment.Dolby Pro Logic gz, with front height channels is also an ideal alternative for households that cannot support the placement of back surround speakers of a typical 7.1 channel system but may have bookshelf space available to support the addition of height speakers.

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.

DTS Surround

DTS Digital Surround

DTS Digital Surround is the standard digital surround format of DTS, Inc., compatible with a sampling frequency of 44.1 or 48 kHz and up to 5.1-channels of digital discrete surround sound.

DTS-HD High Resolution Audio

DTS-HD High Resolution Audio is an improved version of the conventional DTS, DTS-ES and DTS 96/24 signals formats, compatible with sampling frequencies of 96 or 48 kHz and up to 7.1-channels of discrete digital sound. High data bit rate performance provides high quality sound. This format is fully compatible with conventional products, including conventional DTS digital surround 5.1-channel data.

DTS-HD Master Audio

DTS-HD Master Audio is DTS, Inc’s lossless audio format compatible with up to 96 kHz/7.1-channels. The lossless audio coding technology faithfully reproduces the sound of the studio master. It is fully compatible with conventional products, including conventional DTS digital surround 5.1-channel data.

DTS-ES™ Discrete 6.1

DTS-ES™ Discrete 6.1 is a 6.1-channel discrete digital audio format adding a surround back (SB) channel to the DTS digital surround sound. Decoding of conventional 5.1-channel audio signals is also possible according to the decoder.

DTS-ES™ Matrix 6.1

DTS-ES™ Matrix 6.1 is a 6.1-channel discrete digital audio format inserting a surround back (SB) channel to the DTS digital surround sound through matrix encoding. Decoding of conventional 5.1-channel audio signals is also possible according to the decoder.

DTS NEO:6™ Surround

DTS NEO:6™ is a matrix decoding technology for achieving 6.1channel surround playback with 2-channel sources. It includes “DTS NEO:6 Cinema” suited for playing movies and “DTS NEO:6 Music” uited for playing music.

Connections Playback Remote Control Troubleshooting

Information

SpeciﬁcationsMulti-ZoneSettings



ENGLISH

Getting Started Connections Playback Remote Control Troubleshooting SpeciﬁcationsMulti-ZoneSettings Information

DTS 96/24

DTS 96/24 is a digital audio format enabling high sound quality playback in 5.1-channels with a sampling frequency of 96 kHz and 24 bit quantization on DVD-Video.

Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS is a registered trademark and the DTS logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks of DTS, Inc.© 1996-2008 DTS, Inc. All Rights Reserved.

Audyssey

Audyssey MultEQ®

Audyssey MultEQ is a room equalization solution that calibrates any audio system so that it can achieve optimum performance for every listener in a large listening area. Based on several room measurements, MultEQ calculates an equalization solution that corrects for both time and frequency response problems in the listening area and also performs a fully automated surround system setup.

Surround

Audyssey Dynamic Volume™

Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Audyssey Dynamic EQ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression, and dialog clarity remain the same.

Manufactured under license from Audyssey Laboratories. U.S. and foreign patents pending. Audyssey MultEQ® is a registered trademark of Audyssey Laboratories. Audyssey Dynamic EQ™ is a trademark of Audyssey Laboratories. Audyssey Dynamic Volume™

is a trademark of Audyssey Laboratories.

Audyssey Dynamic EQ™

Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Audyssey Dynamic EQ works in tandem with Audyssey MultEQ to provide well-balanced sound for every listener at any volume level.



ENGLISH

Surround

Surround Modes and Parameters

Signals and adjustability in the different modes

Surround mode

Front L/R Center

PURE DIRECT, DIRECT MULTI CH DIRECT STEREO EXT. IN MULTI CH IN DOLBY PRO LOGIC gx S D D D A D S (OFF) A A S S (NOTE1) S (Cinema) A A A A S (Auto) DOLBY PRO LOGIC g S D D A A D S (OFF) A A S S (NOTE2) S (Cinema) A A A A S (Auto) DTS NEO:6 DOLBY PRO LOGIC gz S D D A D D S (OFF) A A A S (OFF) A A A A A A DOLBY DIGITAL DOLBY DIGITAL Plus DOLBY TrueHD DTS SURROUND DTS 96/24 DTS-HD 5CH/7CH STEREO ROCK ARENA JAZZ CLUB MONO MOVIE VIDEO GAME MATRIX VIRTUAL

S D D D A D S (OFF) S (0dB) A A A A A A A S S (Auto) S D D D A D A S (0dB) S (ON) S A A A A A A A S A A A A D S (OFF) S (0dB) A A A A A A A A S (Auto) S D D D A D A A A A A A A A A A A S D D D A D A S (0dB) S (ON) S A A A A A A A

S D D D A D S (OFF) A A S S (NOTE1) S (Cinema) A A A A A

S D D D D D S (OFF) S (0dB) S (ON) S S (OFF) A A A A A A S D D D D D S (OFF) S (0dB) S (ON) S S (OFF) A A A A A A S D D D D D S (OFF) S (0dB) S (ON) S S (OFF) A A A A A S (Auto) S D D D D D S (OFF) S (0dB) S (ON) S S (OFF) A A A A A A S D D D D D S (OFF) S (0dB) S (ON) S S (OFF) A A A A A A S D D D D D S (OFF) S (0dB) S (ON) S S (OFF) A A A A A A S D D D D D S (OFF) S (0dB) A S A A A A A A A S D D D D D S (OFF) S (0dB) A S A A S D D D D D S (OFF) S (0dB) A S A A S D D D D D S (OFF) S (0dB) A S A A S D D D D D S (OFF) S (0dB) A S A A S D D D D D S (OFF) S (0dB) A S A A A A S (30 ms) A A S A A A A D S (OFF) S ( 0dB) A A A A A A A A A

S : Signal / Adjustable A : No signal / Not adjustable D : Turned on or off by speaker conﬁguration setting

Channel output Parameter (default values are shown in parentheses)

Surround

L/R

Surround Back L/R

Front Height

L/R

Subwoofer

D. Comp

S : Signal / Adjustable A : No signal / Not adjustable

NOTE1 : This parameter is available when the menu “Mode” ( NOTE2 : This parameter is available when the menu “Mode” (

NOTE:

1 : When playing Dolby Digital and DTS signals.

2 : When playing Dolby Digital, DTS and Linear PCM (multi ch).

3 : When playing Dolby TrueHD signal.

LFE

AFDM

Surround

Back

Cinema EQ. Mode Room Size

S (Medium) S (Medium) S (Medium) S (Medium)

vpage 44) is set to “Cinema”.

vpage 44) is set to “Cinema” or “PL”.

Effect

S (10) A A A S (10) A A A S (10) A A A S (10) A A A

Delay Time Subwoofer

Level

DRC

Getting Started

Connections Playback Remote Control Troubleshooting

Information

SpeciﬁcationsMulti-ZoneSettings



ENGLISH

Getting Started Connections Playback Remote Control Troubleshooting SpeciﬁcationsMulti-ZoneSettings Information

Signals and adjustability in the different modes

Parameter (default values are shown in parentheses)

Surround mode

PURE DIRECT, DIRECT MULTI CH DIRECT STEREO EXT. IN MULTI CH IN DOLBY PRO LOGIC gx S (OFF) S (3) S (3) A A S (0dB) S (OFF) S (OFF) S (OFF) S DOLBY PRO LOGIC g S (OFF) S (3) S (3) A A S (0dB) S (OFF) S (OFF) S (OFF) S DTS NEO:6 DOLBY PRO LOGIC gz A A A A A S (0dB) S (OFF) S (OFF) S (OFF) A DOLBY DIGITAL DOLBY DIGITAL Plus DOLBY TrueHD DTS SURROUND DTS-96/24 DTS-HD 5CH/7CH STEREO ROCK ARENA JAZZ CLUB MONO MOVIE VIDEO GAME MATRIX VIRTUAL

PRO LOGIC g/gx MUSIC mode only

Panorama Dimension Center Width Center Image Subwoofer ATT

A A A A A A A A A A A A A A A A A A A A A A A A A S (0dB) S (OFF) S (OFF) S (OFF) S A A A A S A A A A A A A A A A S (0dB) S (OFF) S (OFF) S (OFF) A

A A A S (0.3) A S (0dB) S (OFF) S (OFF) S (OFF) S

A A A A A S (0dB) S (OFF) S (OFF) S (OFF) A A A A A A S (0dB) S (OFF) S (OFF) S (OFF) A A A A A A S (0dB) S (OFF) S (OFF) S (OFF) A A A A A A S (0dB) S (OFF) S (OFF) S (OFF) A A A A A A S (0dB) S (OFF) S (OFF) S (OFF) A A A A A A S (0dB) S (OFF) S (OFF) S (OFF) A A A A A A S (0dB) S (OFF) S (OFF) S (OFF) S A A A A A S (NOTE3) S (OFF) S (OFF) S (OFF) S A A A A A S (0dB) S (OFF) S (OFF) S (OFF) S A A A A A S (0dB) S (OFF) S (OFF) S (OFF) S A A A A A S (0dB) S (OFF) S (OFF) S (OFF) S A A A A A S (0dB) S (OFF) S (OFF) S (OFF) S A A A A A S (0dB) S (OFF) S (OFF) S (OFF) S

S : Adjustable A : Not adjustable

NOTE3 : BASS +6 dB, TREBLE +4 dB NOTE4 : Cannot be set when the “Dynamic EQ” ( NOTE5 : Cannot be set when the “MultEQ” ( NOTE6 : Cannot be set when the “Dynamic EQ” ( NOTE7 : “RESTORER” can be set for analog or PCM 48 kHz or 44.1 kHz input signals.

NEO:6 MUSIC

mode only

vpage 46) setting is “ON”.

vpage 46) setting is “OFF”.

EXT. IN only

Tone Control

(NOTE4)

MultEQ

Dynamic EQ

(NOTE5)

Dynamic

(NOTE6)

Volume

Surround

RESTORER

(NOTE7)

8

Differences in Surround Mode Names Depending on the Input Signals

ENGLISH

Surround

Getting Started

Button

Input signals

PCM DTS-HD DTS DOLBY DOLBY DIGITAL

Surround mode

Note

ANALOG

Linear

PCM

(multi ch)

Linear

PCM (2ch)

DTS-HD

Master

Audio

DTS-HD

High

Resolution

Audio

DTS ES DSCRT

(With Flag)

DTS ES

MTRX

(With Flag)

DTS

(5.1ch)

DTS

96/24

DOLBY TrueHD

DOLBY

DIGITAL

Plus

DOLBY DIGITAL EX (With

Flag)

DOLBY

DIGITAL EX

(With no

Flag)

DOLBY

DIGITAL

(5.1/5/4ch)

STANDARD

DTS SURROUND

DTS-HD MSTR DTS-HD HI RES DTS ES DSCRT6.1 DTS ES MTRX6.1 DTS SURROUND DTS 96/24 DTS (–HD) + PLgx CINEMA DTS (–HD) + PLgx MUSIC DTS (–HD) + PLgz DTS (–HD) + NEO:6 DTS NEO:6 CINEMA DTS NEO:6 MUSIC

z1 z

z2 z

z1 z

A A A F A A A A A A A A A A A A A A A A F A A A A A A A A A A A

A A A A A F D A A A A A A A A A A

A A A A A A F D A A A A A A A A A A A A A A S S F A A A A A A A A A A A A A A A A F A A A A A A A

A A A S S S S S S A A A A A A A

A A A S S A S S S A A A A A A A S A S A A A A A A A A A A A A S S A S A A A A A A A A A A A A S

DOLBY SURROUND

DOLBY TrueHD DOLBY DIGITAL+ DOLBY DIGITAL EX DOLBY (D+) (HD) +EX DOLBY DIGITAL DOLBY (D) (D+) (HD) +PLgx CINEMA DOLBY (D) (D+) (HD) +PLgx MUSIC DOLBY (D) (D+) (HD) +PLgz DOLBY PRO LOGIC gx CINEMA DOLBY PRO LOGIC gx MUSIC DOLBY PRO LOGIC gx GAME DOLBY PRO LOGIC g

z1 z

z2 z

z1 z

A A A A A A A A A F A A A A A A

A A A A A A A A A A F A A A A A

A A A A A A A A A A A S S S S A

A A A A A A A A A S S A A A A A

A A A A A A A A A A A S F F F A

A A A A A A A A A S S F D S S S A

A A A A A A A A A S S S S S S A

S A S A A A A A A A A A A A A S

DOLBY PRO LOGIC g CINEMA S A S A A A A A A A A A A A A S DOLBY PRO LOGIC g MUSIC S A S A A A A A A A A A A A A S DOLBY PRO LOGIC g GAME S A S A A A A A A A A A A A A S DOLBY PRO LOGIC

NOTE:

1: This mode is not available when the surround back speaker setup is set to “None”.

2: This mode is not available when the surround back speaker setup is set to “1sp” or “None”.

3: Can be set when “Amp Assign” is set to “Normal”.

4: Not selectable when “Amp Assign” is set to anything other than “Front Height”.

S A S A A A A A A A A A A A A S

F : Mode selectable in initial status D : Mode ﬁxed when “AFDM” is “ON” S : Selectable mode A : Non-selectable mode

DOLBY

DIGITAL

(4/3ch)

DOLBY

Connections Playback Remote Control Troubleshooting

DIGITAL

(2ch)

Information

SpeciﬁcationsMulti-ZoneSettings



ENGLISH

Getting Started Connections Playback Remote Control Speciﬁcations

Multi-ZoneSettings Troubleshooting

Information

Button

Surround mode

STANDARD

MULTI CH IN

MULTI CH IN MULTI IN + PLgx CINEMA MULTI IN + PLgx MUSIC MULTI IN + PLgz MULTI IN + Dolby EX MULTI CH IN 7.1

DIRECT

DIRECT MULTI CH DIRECT M DIRECT + PLgx CINEMA M DIRECT + PLgx MUSIC M DIRECT + PLgz M DIRECT + Dolby EX M DIRECT 7.1

PURE DIRECT

PURE DIRECT MULTI CH PURE DIRECT M PURE D + PLgx CINEMA M PURE D + PLgx MUSIC M PURE D + PLgz M PURE D + Dolby EX M CH PURE DIRECT 7.1

DSP SIMULATION

5CH/7CH STEREO ROCK ARENA JAZZ CLUB MONO MOVIE VIDEO GAME MATRIX VIRTUAL

STEREO

Note

z2 z

z1 z

z2 z

z1z

z1 z

z2 z

z1 z

Input signals

PCM DTS-HD DTS DOLBY DOLBY DIGITAL

ANALOG

Linear

PCM

(multi ch)

Linear

PCM (2ch)

DTS-HD

Master

Audio

DTS-HD

High

Resolution

Audio

DTS ES DSCRT

(With Flag)

DTS ES

MTRX

(With Flag)

DTS

(5.1ch)

DTS

96/24

DOLBY TrueHD

DOLBY

DIGITAL

Plus

DOLBY

DIGITAL

EX (With

Flag)

DOLBY

DIGITAL

EX (With

no Flag)

DOLBY

DIGITAL

(5.1/5/4ch)

A F A A A A A A A A A A A A A A

A S A A A A A A A A A A A A A A

A F D (7.1) A A A A A A A A A A A A A A

S A S S S S S S S S S S S S S S

A S A A A A A A A A A A A A A A

A S (7.1) A A A A A A A A A A A A A A

S A S S S S S S S S S S S S S S

A S A A A A A A A A A A A A A A

A S (7.1) A A A A A A A A A A A A A A

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

F S F S S S S S S S S S S S S S

DOLBY

DIGITAL

(4/3ch)

Surround

DOLBY

DIGITAL

(2ch)

0

NOTE :

1: This mode is not available when the surround back speaker setup is set to “None”.

2: This mode is not available when the surround back speaker setup is set to “1sp” or “None”.

3: Can be set when “Amp Assign” is set to “Normal”.

4: If the surround back speaker setup is set to “None”, then “5CH STEREO” is displayed.

5: Not selectable when “Amp Assign” is set to anything other than “Front Height”.

F : Mode selectable in initial status D : Mode ﬁxed when “AFDM” is “ON” S : Selectable mode A : Non-selectable mode

Troubleshooting

ENGLISH

Getting Started

If a problem should arise, ﬁrst check the following:

1. Are the connections correct?

2. Is the set being operated as described in the owner’s manual?

3. Are the other components operating properly?

If this unit does not operate properly, check the items listed in the table below. Should the problem persist, there may be a malfunction. In this case, disconnect the power immediately and contact your store of purchase.

GGeneralH

Symptom Cause Countermeasure Page

Set does not operate properly.

Power does not turn on, or turns off directly after it was turned on.

No sound is produced from speakers.

Display is off. • The “Display” setting is set to

“DOLBY DIGITAL” indicator does not appear on display.

• External noise or interference is causing the set to malfunction.

• Connection of the power cord is faulty.

• Connection with the input devices or connection of the speaker cables is faulty.

• Device you want to play and set input source do not match.

• Master volume is turned too low.

• Mute mode is set.

• Headphones are connected.

• No digital signals are being input.

• The connectors to which the digital inputs are assigned and the settable input modes do not match.

“OFF”.

• The PURE DIRECT mode is set.

• Blu-ray Disc player / DVD player’s digital audio output setting is not proper.

• Reset the microprocessor. 63

• Check the insertion of the power cord plug.

• Check the connections.

• Select an appropriate input source.

• Adjust the master volume to an appropriate level.

• Cancel the mute mode.

• Disconnect the headphones.

• Select an input source for which the digital input setting has been made.

• Set the input mode.

• Set to something other than “OFF”.

• Set a surround mode other than the PURE DIRECT mode.

• Check the Blu-ray Disc player / DVD player’s audio output setting. For details, read the Blu-ray Disc player / DVD player’s operating instructions.

41 41 33

–

Symptom Cause Countermeasure Page

Power switches off suddenly while you are using the AVR-1910, the power indicator will ﬂash in red at intervals of approximately 2 seconds.

Power switches off suddenly while you are using the AVR-1910, the power indicator will ﬂash red at intervals of approximately 0.5 seconds.

Even applying power, the power display ﬂashes red at intervals of approximately 0.5 seconds.

Set does not work properly when remote control unit operated.

• The protection circuit will be activated depending upon the temperature rise in the internal parts of the unit.

• Use speakers having impedance less than that speciﬁed.

• If speaker cable core wires touch each other or the core wires become disconnected from their terminals, the protection circuit will be activated in the event of core wires coming into contact with the AVR-1910 rear panel.

• The AVR-1910 ampliﬁer circuit has failed.

• Batteries are worn.

• You are operating outside of the speciﬁed range.

• Obstacle between main unit and remote control unit.

• The batteries are not inserted in the proper direction, as indicated by the polarity marks in the battery compartment.

• The set’s remote control sensor is exposed to strong light (direct sunlight, inverter type ﬂuorescent bulb light, etc.).

• Settings do not match the remote control unit’s DEVICE

SELECT switch.

• Please switch off power at once, and re-apply the power after the body temperature has fallen sufﬁciently.

• Please re-install AVR-1910 in a place having good ventilation.

• Please use speakers which have the speciﬁed impedance.

• Unplug the power cord, then after twisting the core wires together tightly again, or effecting termination treatments etc, please reconnect once again.

• Switch off the power and please contact the DENON service adviser.

• Replace with new batteries.

• Operate within the speciﬁed range.

• Remove the obstacle.

• Insert the batteries in the proper direction, following the polarity marks in the battery compartment.

• Move the set to a place in which the remote control sensor will not be exposed to strong light.

• Match the settings to the remote control unit’s DEVICE SELECT switch.

–

3 3

Connections Playback Remote Control Information

Multi-ZoneSettings

Troubleshooting

Speciﬁcations



ENGLISH

Getting Started Connections Playback Remote Control Information Speciﬁcations

GAudioH

No sound is produced from center speaker.

No sound is produced from surround speakers.

No sound is produced from surround back speaker.

Multi-ZoneSettings Troubleshooting

No sound is produced from subwoofer.

DTS sound is not output.

HDMI audio signals are not output from speakers.

No sound is output from the monitor connected with HDMI connections.

Symptom Cause Countermeasure Page

• You are playing a monaural source (TV, etc.) in the “STANDARD” (Dolby/DTS Surround) mode.

• The surround mode is set to “STEREO”, “DIRECT” or “PURE DIRECT”.

• The surround back speaker’s power ampliﬁer is assigned to a different channel.

• “S.Back” setting is set to “None”.

• The “Parameter” – “Surround Parameter” – “Surround Back” settings are “OFF”.

• Surround mode not set to a mode for 6.1- or 7.1-channel playback.

• Subwoofer’s power not turned on.

• The “Subwoofer” setting at “Speaker Conﬁg.” is set to “No”.

• The subwoofer is not properly connected.

• The subwoofer’s volume is turned off.

• Blu-ray Disc player / DVD player’s audio output setting is not set to bitstream.

• Blu-ray Disc player / DVD player is not compatible with DTS sound playback.

• The AVR-1910’s “Decode Mode” setting is set to “PCM”.

• The “Manual Setup” – “HDMI Setup” – “HDMI Audio Out” setting is set to “TV”.

• The “Manual Setup” – “HDMI Setup” – “HDMI Audio Out” setting is set to “AMP”.

• The mode is set to something other than “STANDARD” (Dolby/ DTS Surround).

• Set to a surround playback mode.

• Check the setting and change it as necessary.

• Set to something other than “None”.

• Please set “Parameter” – “Surround Parameter” – “Surround Back” to settings other than “OFF”.

• Select a surround playback mode.

• Turn on the subwoofer’s power.

• Set to “Yes”.

• Check the connections.

• Adjust the subwoofer’s volume to an appropriate level.

• Set the Blu-ray Disc player / DVD player. For details, refer to the Blu-ray Disc player / DVD player’s operating instructions.

• Use a DTS-compatible player.

• Set to the “Auto” or “DTS” mode.

• Set to “AMP”. 28

• Set to “TV”. 28

42, 43

–

Symptom Cause Countermeasure Page

Dolby TrueHD, DTS-HD, Dolby Digital Plus audio is not output.

GVideoH

Symptom Cause Countermeasure Page

No picture appears.

Picture cannot be recorded.

DVDs cannot be copied on a DVR.

The menu screen and status indicators are not displayed.

• HDMI is not connected.

• Blu-ray Disc player’s audio output setting is not set to bitstream.

• Blu-ray Disc player is not compatible with DTS sound playback.

• The connections between the AVR-1910 and monitor are faulty.

• The monitor’s input setting is wrong.

• PURE DIRECT mode is set.

• The player is connected using the component input connectors, the monitor is connected using the video (yellow) output connectors.

• Input source does not match recorder’s video connection connector (video).

–

• “OFF” is displayed for the status.

• The main volume display is “OFF”.

• The display during tuner operation is “OFF”.

• The display during iPod operation is “OFF”.

• Connect the HDMI.

• Set the Blu-ray Disc player. For details, refer to the Blu-ray Disc player’s operating instructions.

• Use a DTS-compatible player.

• Check the connections.

• Set properly.

• Cancel the PURE DIRECT mode.

• High deﬁnition (1080i/720p) and progressive (480p/576p) video signals are not down-converted. Set the player to interlace (480i/576i) signals.

• The video conversion function does not work for the REC OUT connectors. Match the input source and recorder connections.

• This is not a malfunction. Most movie software includes copy prevention signals and cannot be copied.

• When viewing HDMI or component video signals via the AVR-1910, the on-screen display appears when the MENU button on the main unit or the MENU button on the main remote control unit.

• Set “Manual Setup” – “Option Setup” – “On-Screen Display” – “Text” to “ON”.

• Set “Manual Setup” – “Option Setup” – “On-Screen Display” – “Master Volume” to “Top” or “Bottom”.

• Set when “Manual Setup” – “On-Screen Display” – “Tuner Information” is not “OFF”.

• Set when “Manual Setup” – “On-Screen Display” – “ iPod Information” is not “OFF”.

–

13 ~ 16

–

2

GHDMIH

Symptom Cause Countermeasure Page

HDMI audio signals are not output from speakers.

• The “Manual Setup” – “HDMI Setup” – “HDMI Audio Out” setting is set to“TV”

• Set to “Amp” 28

Restoring all the settings to as they were at the time of purchase (Resetting the Microprocessor)

Perform this procedure if the display is abnormal or if operations cannot be performed.

When the microprocessor is reset, all the settings are reset to their default values.

ENGLISH

Getting Started

Connections Playback Remote Control Information

No picture appears with HDMI connections.

No sound is output from the monitor connected with HDMI connections.

When performing the following operations on a connected device, AVR-1910 has the same operations.

⋅ Power ON/OFF ⋅ Switching audio

output devices

⋅ Adjust volume ⋅ Switch input

source

GiPodH

Symptom Cause Countermeasure Page

iPod cannot be played.

• The connections to the HDMI connectors are faulty.

• HDMI input setting is improper.

• The monitor is not compatible with copyright protection (HDCP).

• The HDMI format of the player and monitor do not match.

• The “Manual Setup” – “HDMI Setup” – “HDMI Audio Out” setting is set to “Amp”.

• HDMI’s CEC function is operating.

• The input source assigned to “iPod Dock” is not selected.

• Cable is not properly connected.

• Control dock for iPod’s AC adapter is not connected to power outlet.

• Check the connections.

• Check the HDMI input setting.

• Connect a monitor that is compatible with copyright protection (HDCP).

• Match the HDMI format of the player and monitor.

• Set to “TV”. 28

• Set “Manual Setup” – “HDMI Setup” -– “HDMI Control” to “OFF”.

When you only want to operate

the power on/off each device, set “Power Off Control” to “OFF”.

• Switch to the input source assigned at “iPod Dock”.

• Reconnect.

• Plug the control dock for iPod’s AC adapter into a power outlet.

33 12

Turn off the power using on the main unit.

Press while simultaneously pressing and on the main unit.

Once the display starts ashing at intervals of about 1 second, release the two

buttons.

Multi-ZoneSettings

If in step 3 the display does not ﬂash at intervals of about 1 second, start over from step 1.

Troubleshooting

Speciﬁcations

–



ENGLISH

Getting Started Connections Playback Remote Control Information Troubleshooting

Speciﬁcations

Audio section

• Power ampliﬁer Rated output:

90 W+ 125 W+125 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) Center: 90 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.) 125 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) Surround: 90 W+90 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.) 125 W+125 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) Surround Back: 90 W+90 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.) 125 W+125 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)   Output connectors: Front: A or B 6 ~ 16 Ω/ohms A + B 12

Multi-ZoneSettings

Center, Surround, Surround Back / Amp Assign: 6 ~ 16 Ω/ohms

• Analog Input sensitivity / Input impedance: Frequency response: S/N:

Video section

• Standard video connectors Input / output level and impedance: Frequency response:

• Color component video connector Input / output level and impedance:

P P

Frequency response:

Tuner section [FM] [AM]

(note: µV at 75 Ω/ohms, 0 dBf = 1 x 10

Receiving Range: 87.5 MHz ~ 108.0 MHz 522 kHz ~ 1611 kHz Usable Sensitivity: 1.2 µV (12.8 dBf) 18 µV 50 dB Quieting Sensitivity: MONO 2.0 µV (17.3 dBf)

STEREO 42 µV (34.5 dBf) S/N (IHF-A): MONO 72 dB STEREO 67 dB

Speciﬁcations

Total harmonic Distortion (at 1 kHz): MONO 0.3 %

STEREO 0.7 %

General

Power supply: AC 230 V, 50 Hz Power consumption:

0.3 W (Standby)

Maximum external dimensions: Weight: 10.6 kg

Remote control unit (RC-1117)

Batteries: R6/AA Type (two batteries) Maximum external dimensions: Weight: 184 g (including batteries)

z For purposes of improvement, speciﬁcations and design are subject to change without notice.

 Front (A, B):

90 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)

200 mV / 47 kΩ/kohms 10 Hz ~ 100 kHz — +1, –3 dB (DIRECT mode) 100 dB (IHF-A weighted, DIRECT mode)

1 Vp-p, 75 Ω/ohms 5 Hz ~ 10 MHz — +1, –3 dB

Y (brightness) signal — 1 Vp-p, 75 Ω/ohms

B / CB signal — 0.7 Vp-p, 75 Ω/ohms R / CR signal — 0.7 Vp-p, 75 Ω/ohms

5 Hz ~ 60 MHz — +0, –3 dB

460 W

434 (W) x 171 (H) x 377 (D) mm

52 (W) x 243 (H) x 21 (D) mm

~ 16 Ω/ohms

-15



List of preset codes / Liste von voreingestellten Codes / Liste de codes préréglés / Lista dei codici pre-regolati / Lista de códigos pre-ajustados / Lijst van vooringestelde codes / Förteckning över förinställda koder

DEVICE SELECT : TV

Television

3M 100 Addison 163

Admiral 033, 044, 050, 141 Advent 130 Adventura 041 Aiko 138 Akai 018, 019, 034, 119, 137, 151 Albatron 127, 131 Alleron 039 America Action 139 Ampro 129 Amtron 038 Anam 139 Anam National 035, 038 AOC 030, 036, 079, 137 151, 154 Apex 048, 062 Apex Digital 174 Audiovox 038, 067, 071, 138, 139, 140 Aventura 029 Axion 120 Bang & Olufsen 146

Barco 020 Baur 034 Belcor 030 Bell & Howell 033 Benq 089, 135 Blue Sky 020 Bradford 038, 139 Brillian 145 Brockwood 030 Broksonic 050, 139, 141 byd:sign 123 Candle 037, 041, 137, 151

Carnivale 137, 151 Carver 155 CCE 147, 152 Celebrity 034 Celera 048 Changhong 048 Ching Tai 163 Chun Yun 157, 163, 169, 173 Chung Hsin 160, 169

Citizen

Clarion 139 Coby 074

037, 038, 049, 137, 138, 151, 153, 156

Contec 139 Contec/Cony 038 Craig 038, 139 Crosley 049, 155 Crown 038, 139, 153 CTX 082

Curtis Mathes

CXC 038, 139 Cytron 118 Daewoo 030, 036, 049, 138, 140, 153

Daytron 030 Dell 012, 032 Denon 143 DiamondVision 125 Dimensia 010 Disney 060 Dumont 013, 030

Durabrand

Dwin 044, 128 Electroband 034

Electrograph 142 Electrohome 034, 035, 050 Element 106

Emerson

Emprex 124 Envision 137, 151 Epson 080, 097 Erres 149 ESA 018, 029 Ether 158 Firstar 170

Fujitsu 037, 039, 077 Funai 029, 038, 039, 139 Furi 165 Futuretech 038, 139 Gateway 085, 142, 144

GFM 027, 028 Gibralter 013, 030, 137, 151 Go Video 134 Goldstar 012, 030, 036, 137, 151 Gradiente 084 Grundig 152 Grunpy 038, 039, 139 Haier 107, 114, 136, 148

Hallmark 012 Hankook 158, 168, 169 Harman/Kardon 155

010, 019, 044, 137, 140, 143, 151, 153, 155, 156

012, 029, 050, 111, 136, 139, 141

012, 029, 030, 038, 039, 049, 050, 139, 141, 153

010, 012, 035, 040, 045, 055, 140

Harvard 038, 139 Havermy 044 Hello Kitty 140 Hewlett Packard 068 Hisense 087, 167, 174 Hitachi [014]z, 058, 103, 143, 181 HP 031 Hyundai 133 Ilo 090, 115, 117, 122

IMA 038 Inﬁnity 155 InFocus 099 Initial 117 Innova 152 Insignia 029, 108, 109, 110 Janeil 041

JBL 155 JC Penney 010, 036, 037, 040 JCB 034 Jean 159, 163, 167, 170 Jinxing 161, 165, 167 JVC 023, 024, 025, 040, 050 Kawasho 034

Kaypani 154 KEC 139 Kenwood 030, 137, 151 Kioto 020, 155 KLH 048 Kloss Novabeam 038, 041 Kolin 166, 169 KTV 038, 137, 139, 147, 151, 153 LG 012, 030, 036, 127, 151

Logik 033 LXI 010, 012, 155 M & S 155

Magnasonic 049

Magnavox

Majestic 033 Marantz 046, 137, 151, 152, 155 Maxent 112, 142 Mediator 149 Megapower 127 Megatron 012, 143 Memorex 012, 029, 033, 036, 050, 141 MGA 012, 030, 036, 137, 151 Megatron 013, 040, 153 Mintek 117 Mitsubishi 012, 030, 036, 044, 057, 178 Monivision 127, 131

028, 037, 047, 054, 056, 137, 151, 155

Montgomery Ward 033 Motorola 035, 044 MTC 030, 036, 137, 151, 156 Multitech 038, 139, 147 NAD 012, 152

NEC 030, 035, 036, 081, 137, 151 Netsat 152 Net-TV 090, 142 Newave 163, 164, 168 Nikko 012, 137, 138, 151 Norcent 079, 174 Norwood Micro 090 Noshi 150 NTC 138 Olevia 064, 072, 078

Onwa 038, 139 Oppo 121 Optoma 098 Optonica 044 Orion 050, 141 Otto Versand 034

Panasonic

Penney

Philco

Philips

Philips Magnavox 020, 046, 047 Phonola 149 Pilot 030, 137, 151, 153 Pioneer 180, 184 Polaroid 030, 048, 075 Portland 030, 036, 138, 153 Prima 083, 130 Princeton 127 Prism 040 Proscan 010 Proton 012, 154 Protron 073 Proview 086, 106 Pulsar 013, 030 Pye 149 Quasar 035, 040

Quelle 034 Radio Shack/

Realistic Radiola 149

RadioShack 012, 030, 137, 139, 151, 153

RCA

Realistic 012, 030, 137, 139, 151, 153

007, 008, 009, 035, 040, 059, 069, 176 012, 030, 137, 150, 151, 153, 156 030, 035, 036, 037, 050, 137, 151, 155 020, 021, 022, 035, 037, 046, 066, 105, 149, 152,155

010, 038

010, 011, 030, 035, 036, 043, 045, 150, 156

Runco 013, 137, 151 Sampo 137, 142, 151, 153, 154

Samsung

Samsux 153 Sansui 050, 141 Sanyo 092 SBR 149 Sceptre 096 Scimitsu 030 Scotch 012 Scott 012, 030, 038, 039, 116, 139 Sears 010, 012, 029, 039, 088, 155 SEI 034

Sharp

Shen Ying 163 Sheng Chia 044, 164 Shogun 030 Signature 033 Simpson 037 Sinudyne 034 SKY 152 Skygiant 169

Sony

Soundesign 012, 037, 038, 039, 139 Sova 073 Sowa 162, 167 Squareview 029 SSS 030, 038, 139 Starlite 038, 139 Studio Experience 131 Superscan 044 Supre-Macy 041 Supreme 034 SVA 020, 113, 148, 174

Sylvania

Symphonic 029, 038, 139 Synco 157, 162, 163, 164, 168, 172 Syntax 072 Syntax-Brillian 072, 088 Tacico 163, 168

Tandy 044 Tatung 035, 090, 144, 159, 162, 167 Technics 040 Techview 132 Techwood 040 Teco 159, 164, 168

Teknika

012, 018, 019, 030, 036, 101, 102, 137, 147, 151, 152, 156

015, 016, 017, 044, 070, 153, 179, 183

000, 001, 002, 034, 052, 053, 175, 182

026, 027, 028, 029, 037, 063, 104, 137, 151, 155

030, 033, 036, 037, 038, 039, 138, 139, 153, 155, 156

PRESET CODE



Telefunken 019 TMK 012

Toshiba

Totevision 153 Trutech 091 Tuntex 158, 163 TVS 050, 141 US Logic 090

Vector Research 137, 151

Vidikron 155 Vidtech 012, 030, 036 Viewsonic 061, 076, 142 Viking 041 Viore 115 Vizio 061, 093, 094, 095, 126, 144

Wards

Westinghouse 061, 065, 140 White

Westinghouse Yamaha 030, 036, 137, 151

Yapshe 171

Zenith

003, 004, 005, 006, 030, 051, 156, 177

010, 012, 030, 033, 036, 039, 137, 151, 155

049, 050, 141

012, 013, 014, 030, 033, 042, 050, 138, 141

TV/VCR Combination

RCA 011

Sylvania 026

TV/DVD Combination

Akai 119

Apex 062 Axion 120 Coby 074

Cytron 118 DiamondVision 125

Disney 060 GFM 028

Haier 114

Ilo 117

Initial 117 Insignia 108 LG 030

Mintek 117

Oppo 121

Panasonic 069

Philips 066 Polaroid 075 RCA 010

Sansui 051

Sharp 070 Sylvania 027, 063

PRESET CODE



Toshiba 005, 051

Westinghouse 065

TV/DVD/VCR Combination

Magnavox 028

Panasonic 059

Toshiba 006

DEVICE SELECT : DVD/HDP

Blu-ray Disc Player

Denon 121

DVD Player

Accele Vision 088

Accurian 146 Advent 131 Akai 098, 126 Alco 129 Allegro 142

Amphion MediaWorks

AMW 117

Apex

Apple 109 Arrgo 043 Aspire 132 Astar 090 Audiovox 075, 129 Axion 099 Bang & Olufsen 137

Blaupunkt 136 Blue Parade 039 BOSS 089 Broksonic 061, 126

California Audio

Labs Changhong 071, 153

CineVision 074, 142 Coby 050, 081 Curtis Mathes 143 CyberHome 029, 043, 151, 152, 155, 156 Cytron 097 Daewoo 057, 142

Denon 014, 070, [111]z, 112, 128 Desay 116 DiamondVision 124, 125 Disney 053, 063 Durabrand 144 Emerson 127, 138, 145

117

025, 026, 027, 028, 049, 059, 136

128

Enterprise 138 Epson 120 ESA 145 Fisher 139

Funai 145 Gateway 068, 154

GE 044, 054, 136 GFM 101 Go Video 012, 142 Gradiente 128 Greenhill 136 Haier 103

Harman/Kardon 082, 140 Hitachi 013 Hiteker 025 Ilo 096

Initial 096, 136 Insignia 055, 102, 145 Integra 039 Irradio 091 iSymphony 108 JBL 140

JVC 030, 031, 032, 033, 034 Kawasaki 129

Kenwood 080, 128 KLH 058, 129, 136 Koss 067, 134 Landel 147

Lasonic 141 Lenoxx 133, 144 LG 055, 076, 077, 095, 138, 142 Liquid Video 134 Liteon 068, 146 Magnavox 047, 062, 127, 135, 145

Memorex 053, 126 Microsoft 044 Mintek 096, 136 Mitsubishi 056 Nesa 136

Next Base 147 Nexxtech 115 Onkyo 071, 135

Oppo 100, 114 Optoma 122 Oritron 067, 134

Panasonic

Philips

Pioneer 039, 040, 041, 042, 087 Polaroid 028, 086 Proceed 025 Proscan 044

017, 018, 019, 020, 021, 022, 023, 024, 078, 083, 084, 085, 128, 135 007, 037, 038, 047, 052, 064, 073, 104, 135

Protron 119 Qwestar 067

RCA 035, 036, 039, 044, 129, 136

Regent 133 Rio 142 Rowa 130 Sampo 148, 150

Samsung

Sansui 008, 126 Sanyo 126, 139 Sharp 051, 060, 079, 092, 093, 094 Shinsonic 096 Sonic Blue 142

Sony

Sungale 113 Superscan 127 Sylvania 046, 101, 123, 127, 145 Symphonic 038 Teac 129, 149, 157, 158

Technics 128 Theta Digital 039

Toshiba

Trutech 110 Urban Concepts 135

US Logic 096 Venturer 129

VocoStar 118 Westinghouse 072

Xbox 044

Yamaha 017, 128

Zenith 055, 135, 138, 142

011, 012, 013, 015, 016, 048, 128

000, 001, 002, 003, 004, 005, 006 ,045, 065, 066, 105, 106, 107

007, 008, 009, 010, 069, 126, 135

DVD/VCR Combination

Broksonic 061

CineVision 074

Go Video 012

Insignia 055

Panasonic 018, 019, 020

Samsung 012, 048

Sony 002, 003, 004, 005 Sylvania 046 Toshiba 007, 010

TV/DVD Combination

Akai 098

Apex 026 Audiovox 075 Axion 099 Coby 081

Cytron 097 DiamondVision 124

Disney 063 GFM 101

Haier 103

Ilo 096

Initial 096 Insignia 102 LG 077

Mintek 096

Oppo 100

Panasonic 078

Philips 073 Polaroid 086 RCA 035

Sansui 008

Sharp 079 Sylvania 046, 123 Toshiba 008, 101

Westinghouse 072

TV/DVD/VCR Combination

Magnavox 062

Panasonic 021

Toshiba 009

DEVICE SELECT : DVR/VCR

Digital Video Recorder

ABS 035

Alienware 035 Bang & Olufsen 079

CyberPower 035

Dell 035

DIRECTV

Dish Network 076 Dishpro 076 Echostar 076

Expressvu 076 Gateway 035

GOI 076 Hewlett Packard 035

HNS 072 Howard Computers 035 HP 035 HTS 076

Hughes Network Systems

Humax 063 Hush 035

063, 065, 066, 067, 071, 073, 077

063, 065, 066, 067, 073

iBUYPOWER 035

JVC 063, 076

Linksys 035

Media Center PC 035

Microsoft 035 Mind 035 Niveus Media 035

Northgate 035 Panasonic 070

Philips 063, 065, 066, 067, 068, 072 Proscan 077 RCA 063, 065, 072, 077

ReplayTV 069 Samsung 065, 067, 072

Sonic Blue 069 Sony 035, 064, 074, 078 Stack 035 Systemax 035 Tagar Systems 035

Tivo

Toshiba 035, 075 Touch 035 UltimateTV 077

Viewsonic 035

Voodoo 035 ZT Group 035

063, 064, 065, 068, 073, 074, 078

Video Cassette Recorder

ABS 035

Adventura 008, 033 Aiwa 008, 033 Akai 020 Alienware 035 American High 032 Asha 013, 030 Audio Dynamics 018 Audiovox 031 Beaumark 013, 030

Bell & Howell 029 Broksonic 056 Calix 031

Candle 030, 031 Canon 032 CineVision 058 Citizen 030, 031 Colortyme 018 Craig 013, 030, 031 Curtis Mathes 012, 018, 030, 032 Cybernex 013, 030 CyberPower 035

Daewoo 019, 033

Davidson 008 DBX 018 Dell 035 Denon 014 DIRECTV 061 Durabrand 025 Dynatech 008, 033 Electrohome 010, 031

Electrophonic 031 Emerson 008, 010, 021, 031, 032, 033 Fisher 029

Fuji 026, 032 Funai 008, 021, 033 Garrard 008, 033

Gateway 035 GE 012, 013, 030, 032 Go Video 013, 048 Goldstar 018, 031 Gradiente 008, 033 Harley Davidson 033

Harman/Kardon 018 Headquarter 029 Hewlett Packard 035 Hitachi [008]z, 014 Howard Computers 035 HP 035

Hughes Network Systems

Humax 061 Hush 035 iBUYPOWER 035

Insignia 059 Instant Replay 032 JC Penney 018, 029, 030, 031, 032

JCL 032 JVC 016, 017, 018, 029 Kenwood 018, 029

Kodak 031, 032 LG 031

Linksys 035 Lloyd's 008, 033 LXI 031 Magnasonic 021

Magnavox 008, 021, 022, 025, 028, 032 Magnin 013, 031 Marantz 018, 029, 032 Marta 031 Matsushita 032 Media Center PC 035 MEI 032

Memorex

014, 061

008, 013, 025, 029, 030, 031, 032, 033, 062

MGA 010, 013 MGN Technology 013, 030 Microsoft 035 Mind 035 Minolta 014 Mitsubishi 010, 038 Motorola 032 MTC 008, 013, 030 Multitech 008, 030, 033 NEC 018, 029

Nikko 031 Niveus Media 035 Noblex 013, 030 Northgate 035 Olympus 032

Optimus 021, 031 Optonica 024 Orion 044, 062

Panasonic

Penney 013, 014 Pentax 014 Philco 032 Philips 024, 032, 041, 061 Philips Magnavox 041 Pilot 031 Proﬁtronic 013 Pulsar 025 Quarter 029

Quartz 029 Quasar 032 RadioShack 008, 024, 031

Radio Shack/ Realistic

Radix 031 Randex 031

RCA

Realistic

ReplayTV 060 Ricavision 035 Runco 025

Samsung

Sanky 025 Sansui 008, 044, 062 Sanyo 013, 029, 030 Scott 010, 019 Sears 008, 014, 029, 031, 032 Sharp 023, 024, 042 Shogun 013, 030 Singer 032 Sonic Blue 060

000, 001, 002, 003, 004, 032, 060

024, 029, 030, 031, 032, 033

011, 012, 013 ,014, 015, 030, 032, 051 008, 024, 029, 030, 031, 032, 033

013, 019, 020, 030, 040, 048, 049, 061

Sony

Stack 035 STS 014, 032

Sylvania

Symphonic 008, 021, 022, 033 Systemax 035 Tagar Systems 035

Tandy 029 Tashiko 031 Teac 008, 033 Technics 032 Teknika 008, 031, 032, 033 Thomas 008 Tivo 061 TMK 013, 030

Toshiba

Totevision 013, 030, 031 Touch 035 Unitech 013, 030

Vector 019

Vector Research 018 Video Concepts 018, 019 Videosonic 013, 030 Viewsonic 035 Villain 008 Voodoo 035

Wards

XR-1000 008, 032, 033

Yamaha 018, 029

Zenith 008, 025, 026, 027, 043

ZT Group 035

005, 006, 007, 008, 026 ,034, 035, 036, 037, 045 , 052, 053, 054

008, 010, 021, 022, 032, 033, 046, 055

009, 010, 019, 035, 039, 047, 050, 057

008, 013, 014, 024, 030, 031, 032, 033

DVD/VCR Combination

Broksonic 056

CineVision 058

Go Video 048

Insignia 059

Panasonic 002, 003, 004

Samsung 040, 048, 049

Sony 037, 045, 052, 053, 054 Sylvania 046 Toshiba 039, 050, 057

TV/VCR Combination

RCA 051

Sylvania 055

TV/DVD/VCR Combination

Magnavox 022

Panasonic 001

Toshiba 047

DEVICE SELECT : SAT/CBL

Satellite Receiver

AccessHD 109

Alpha Digital 109 Alphastar 083 Artec 106 CaptiveWorks 102

Channel Master 111 Chaparral 077 Coolsat 103 Coship 114 Crossdigital 120 Digital Stream 110

DIRECTV

Dish Network

Dishpro 115, 119 Drake 078 Echostar 052, 065, 091, 115, 119

Expressvu 119 GE 056, 057, 112

General Instrument 079, 117 GOI 119 Goodmind 112 Hisense 118

Hitachi 074, 084 HTS 119

Hughes Network Systems

Humax 104 Ilo 118

Insignia 096 Jerrold 117

JVC 052, 065, 091, 119 Lasonic 113

LG 096, 105 Magnavox 073, 107

Memorex 073 MicroGem 108 Mitsubishi 068, 099 Motorola 117 Next Level 117

Panasonic 061, 095, 097

058, 059, 060, 061, 062, 063, 064, 068, 069, 073, 074, 075, 076, 088, 089, 090, 093, 095, 116 052, 053, 054, 055, 065, 091, 115, 119

060, 062, 067, 068, 070, 075, 093

PRESET CODE



Pansat 100 Paysat 073 PCT 111 Philco 107

Philips

Pioneer 060 Primestar 082 Proscan 056, 057 Proton 118 RadioShack 117

RCA

Realistic 080 Samsung 060, 062, 069, 070, 071, 094

Sharp 098 Sony 059, 066, 116 Star Choice 117 STS 085 Tivax 109

Tivo 060, 070 Toshiba 063 UltimateTV 116

Uniden 073, 081 US Digital 118 Viewsat 101

Voom 117 Zenith 064, 096

060, 067, 068, 070, 072, 073, 090

056, 057, 058, 070, 076, 086, 087, 088, 089, 092

Cable TV

ABC [009]z, 010, 012, 028, 040

Adelphia 007 Americast 047 Antronix 014, 015 Archer 015 AT&T 003 Bell South 047

Cable Vision 006

Cabletenna 014 Cableview 013 Clearmaster 046 ClearMax 046 Colour Voice 016 Comcast 000, 005, 033 Comtronics 017 Contec 018 Coolmax 046 COX 005 Daeryung 036

Director 033 Dumont 051 Eastern 019

Everquest 041 Focus 045

GC Electronics 015

GE 009, 010 Gehua 033 Gemini 020, 041 General Instrument 005, 010, 033, 044 Goldstar 042 Hamlin 021

Hitachi 010 Jasco 041

Jerrold

LG 050

Magnavox 022

MegaCable 005 Memorex 023, 040

Motorola

Movie Time 024 Multitech 046 NEC 011

NET Brazil 035 NSC 024 Oak 018

Pace 008, 043

Panasonic 026, 027, 040 Paragon 040 Philips 016, 022 Pioneer 002, 030, 036, 042 Popular Mechanics 045 Proscan 009, 010 Pulsar 040 Quasar 040

RadioShack 041, 046

RCA 013, 027 Realistic 015 Recoton 045 Regal 021 Regency 019 Rembrandt 010 Runco 040 Samsung 008, 034, 042

Scientiﬁc Atlanta

Signal 020, 041 Signature 010 Sony 006, 048 Sprucer 027

Standard Component

Starcom 020, 028, 041 Stargate 020, 041 Starquest 020, 041

005, 010, 020, 028, 029, 033, 041, 044

000, 003, 005, 033, 037, 039, 044

001, 002, 003, 007, 012, 036, 038

025

Supercable 044 Supermax 046 Time Warner 004

Tocom 031 Torx 049 Toshiba 040 Trans PX 044 Tristar 046 TS 049 Tusa 020, 041 TV86 024 Unika 014, 015

United Cable 028 Universal 014, 015 V2 046

View Star 018, 022, 024 Viewmaster 046 Vision 046 Vortex View 046 Zenith 032, 040, 047

Zentek 045

DEVICE SELECT : CD

CD Player

Accuphase 018

Acoustic Research 019 ADS 020 Aiwa 021 Akai 022 Audio Alchemy 023 Audio Pro 024 Audio-Technica 025 B & K 026

California Audio

Labs Carver 040, 041

Denon 001, 042, [111]

DKK 035 DMX Electronics 040 Dynamic Bass 041 GE 017

Genexxa 037 Harman/Kardon 007

JVC 003, 011, 012

Kenwood 038, 039

Krell 040

Linn 040

Magnavox 027

Marantz 028 Miro 035

036

Mission 040 Musical Fidelity 029 NEC 030

NSM 040 Onkyo 002

Optimus 035, 037, 039, 041 Philips 009, 010

Pioneer 006 Polk Audio 040 Proscan 017 Proton 040 QED 040

Quad 040 RCA 000, 017

Realistic 041 Rotel 040 SAE 040

Sansui 040 Sanyo 031 SAST 040 Sharp 032 Silsonic 038 Sonic Frontiers 040 Sony 004, 005, 008, 013, 014 Soundesign 033 Symphonic 034 TAG McLaren 040

Technics 015 Wards 040

Yamaha 016

Zonda 040

[ ]* :

Preset codes set upon shipment from the factory.

*[ ] : Sie Voreinstellungscodes wurden vor der

Auslieferung werkseitig eingestellt.

*[ ] : Les codes préréglés diffèrent en fonctiom

des livraison de l’usine.

*[ ] : I codici di presettaggio sono impostati in

fabbrica prima della consegna.

*[ ] : Los códigos vienen preprogramados de

fábrica.

*[ ] : Vooringestelde codes bij hey verlaten van

de fabriek.

*[ ] : Förinställda koder har ställts in vid

transporten från fabriken.

DVD preset codes DVD-Voreinstellungscodes Codes préréglés DVD Codici di preselezione DVD Códigos de preajuste de DVD DVD-voorkeuzecodes Förinställda DVD-koder

111

(default / standard /

défaut / default /

prederminado /

standaard / standard)

DVD-900 DVD-1000 DVD-1400 DVD-1500 DVD-1710 DVD-1720 DVD-1730 DVD-1740 DVD-1910 DVD-1920 DVD-1930 DVD-1940 DVD-2200 DVD-2800

Nº de modelo / Modelnr / Modellnr

DVD-2800g

e Model No. / Modellnr / Modéle numéro / Modello No /

Blu-ray preset codes Blu-ray-Voreinstellungscodes Codes préréglés Blu-ray Codici di preselezione Blu-ray Códigos de preajuste de Blu-ray Blu-ray-voorkeuzecodes Förinställda Blu-ray

Model No. Modellnr Modéle numéro Modello No Nº de modelo Modelnr Modellnr

DVD-2900 DVD-2910 DVD-2930 DVD-3800 DVD-3910 DVD-3930 DVD-A11 DVD-5000 DVD-A1XV DVD-A1XVA DVD-A1 DVM-3700

DVD-1800BD

DVD-2500BT DVD-3800BD DVD-A1UDCI

014

DVD-800 DVD-1600 DVD-2000 DVD-2500 DVD-3000 DVD-3300

121

PRESET CODE

