Denon AVR-1611 Owners Manual

v

Simple
version

3

Einfache Variante

Version simplifiée

Versione semplice

Versión sencilla

Eenvoudige versie

Enkel version

AV SURROUND RECEIVER

AVR-1611

Owner’s Manual
Bedienungsanleitung
Manuel de l’Utilisateur
Manuale delle istruzioni
Manual del usuario
Gebruiksaanwijzing
Bruksanvisning

Basic
version

v

12

Advanced
version

v

28

Information

v

58

Informationen

“Bezeichnung der Teile und deren Funktionen“ (vpage59)

Informations

“Nomenclature et fonctions“ (vpage59)

Informazioni

“Nomi delle parti e funzioni“ (vpage59)

Información

“Nombres y funciones de las piezas“ (vpage59)

Informatie

“Namen en functies van onderdelen“ (vpage59)

Information

“De olika delarna och deras funktioner“ (vpage59)

Basisausführung
Version basique
Versione base
Versión básica
Basisversie
Grundläggande version

Anleitung für Fortgeschrittene

Version avancée

Versione avanzata

Versión avanzada

Geavanceerde versie

Avancerad version

“Part names and functions”
(vpage59)

ENGLISH

SAFETY PRECAUTIONS

n

FRANCAIS

ITALIANO ESPAÑOL NEDERLANDS SVENSKADEUTSCH

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.

The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.

IMPOTANT SAFETY

INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.

9. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.

10. Only use attachments/accessories specified by the manufacturer.

11. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.

12. Unplug this apparatus during lightning storms or when
unused for long periods of time.

13. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.

14. Batteries shall not be exposed to excessive heat such as sunshine, fire or
the like.

CAUTION:

To completely disconnect this product from the mains, disconnect
the plug from the wall socket outlet.
The mains plug is used to completely interrupt the power supply to

the unit and must be within easy access by the user.

VORSICHT:

Um dieses Gerät vollständig von der Stromversorgung abzutrennen,
ziehen Sie bitte den Stecker aus der Wandsteckdose.
Der Netzstecker wird verwendet, um die Stromversorgung zum
Gerät völlig zu unterbrechen; er muss für den Benutzer gut und

einfach zu erreichen sein.

PRECAUTION:

Pour déconnecter complètement ce produit du courant secteur,
débranchez la prise de la prise murale.
La prise secteur est utilisée pour couper complètement
l’alimentation de l’appareil et l’utilisateur doit pouvoir y accéder

facilement.

ATTENZIONE:

Per scollegare completamente questo prodotto dalla rete di
alimentazione elettrica, scollegare la spina dalla relativa presa a

muro.
La spina di rete viene utilizzata per interrompere completamente
l’alimentazione all’unità e deve essere facilmente accessibile
all’utente.

PRECAUCIÓN:

Para desconectar completamente este producto de la alimentación
eléctrica, desconecte el enchufe del enchufe de la pared.

El enchufe de la alimentación eléctrica se utiliza para interrumpir
por completo el suministro de alimentación eléctrica a la unidad

y debe de encontrarse en un lugar al que el usuario tenga fácil
acceso.

WAARSCHUWING:

Om de voeding van dit product volledig te onderbreken moet de
stekker uit het stopcontact worden getrokken.

De netstekker wordt gebruikt om de stroomtoevoer naar het toestel
volledig te onderbreken en moet voor de gebruiker gemakkelijk

bereikbaar zijn.

FÖRSIKTIHETSMÅTT:

Koppla loss stickproppen från eluttaget för att helt skilja produkten
från nätet.
Stickproppen används för att helt bryta strömförsörjningen till

apparaten, och den måste vara lättillgänglig för användaren.

I

NOTE ON USE / HINWEISE ZUM GEBRAUCH / OBSERVATIONS RELATIVES A L’UTILISATION / NOTE SULL’USO /

n

NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA ANGÅENDE ANVÄNDNINGEN

WARNINGS WARNHINWEISE AVERTISSEMENTS AVVERTENZE ADVERTENCIAS WAARSCHUWINGEN VARNINGAR

• Avoid high temperatures.
Allow for sufficient heat
dispersion when installed in a
rack.

• Handle the power cord carefully.
Hold the plug when unplugging
the cord.

• Keep the unit free from
moisture, water, and dust.

• Unplug the power cord when
not using the unit for long
periods of time.

• Do not obstruct the ventilation
holes.

• Do not let foreign objects into
the unit.

• Do not let insecticides,
benzene, and thinner come in
contact with the unit.

• Never disassemble or modify
the unit in any way.

• Ventilation should not be
impeded by covering the
ventilation openings with
items, such as newspapers,
tablecloths or curtains.

• Naked flame sources such as
lighted candles should not be
placed on the unit.

• Observe and follow local
regulations regarding battery
disposal.

• Do not expose the unit to
dripping or splashing fluids.

• Do not place objects filled with
liquids, such as vases, on the
unit.

• Do not handle the mains cord
with wet hands.

• When the switch is in the OFF
position, the equipment is not
completely switched off from
MAINS.

• The equipment shall be
installed near the power supply
so that the power supply is
easily accessible.

• Vermeiden Sie hohe Temperaturen.
Beachten Sie, dass eine
ausreichende Belüftung
gewährleistet wird, wenn das Gerät
auf ein Regal gestellt wird.

• Gehen Sie vorsichtig mit dem
Netzkabel um.
Halten Sie das Kabel am
Stecker, wenn Sie den Stecker
herausziehen.

• Halten Sie das Gerät von
Feuchtigkeit, Wasser und Staub
fern.

• Wenn das Gerät längere Zeit
nicht verwendet werden soll,
trennen Sie das Netzkabel vom
Netzstecker.

• Decken Sie den Lüftungsbereich
nicht ab.

• Lassen Sie keine fremden
Gegenstände in das Gerät
kommen.

• Lassen Sie das Gerät nicht
mit Insektiziden, Benzin oder
Verdünnungsmitteln in Berührung
kommen.

• Versuchen Sie niemals das Gerät
auseinander zu nehmen oder zu
verändern.

• Die Belüftung sollte auf keinen
Fall durch das Abdecken der
Belüftungsöffnungen durch
Gegenstände wie beispielsweise
Zeitungen, Tischtücher, Vorhänge
o. Ä. behindert werden.

• Auf dem Gerät sollten keinerlei
direkte Feuerquellen wie
beispielsweise angezündete
Kerzen aufgestellt werden.

• Bitte beachten Sie bei der
Entsorgung der Batterien
die örtlich geltenden
Umweltbestimmungen.

• Das Gerät sollte keiner tropfenden
oder spritzenden Flüssigkeit
ausgesetzt werden.

• Auf dem Gerät sollten keine mit
Flüssigkeit gefüllten Behälter wie
beispielsweise Vasen aufgestellt
werden.

• Das Netzkabel nicht mit feuchten
oder nassen Händen anfassen.

• Wenn der Schalter ausgeschaltet
ist (OFF-Position), ist das Gerät
nicht vollständig vom Stromnetz
(MAINS) abgetrennt.

• Das Gerät sollte in der Nähe einer
Netzsteckdose aufgestellt werden,
damit es leicht an das Stromnetz
angeschlossen werden kann.

• Eviter des températures
élevées.
Tenir compte d’une dispersion
de chaleur suffisante lors de
l’installation sur une étagère.

• Manipuler le cordon
d’alimentation avec précaution.
Tenir la prise lors du
débranchement du cordon.

• Protéger l’appareil contre
l’humidité, l’eau et la poussière.

• Débrancher le cordon
d’alimentation lorsque l’appareil
n’est pas utilisé pendant de
longues périodes.

• Ne pas obstruer les trous
d’aération.

• Ne pas laisser des objets
étrangers dans l’appareil.

• Ne pas mettre en contact des
insecticides, du benzène et un
diluant avec l’appareil.

• Ne jamais démonter ou
modifier l’appareil d’une
manière ou d’une autre.

• Ne pas recouvrir les orifi ces
de ventilation avec des objets
tels que des journaux, nappes
ou rideaux. Cela entraverait la
ventilation.

• Ne jamais placer de flamme
nue sur l'appareil, notamment
des bougies allumées.

• Veillez à respecter les lois en
vigueur lorsque vous jetez les
piles usagées.

• L’appareil ne doit pas être
exposé à l’eau ou à l’humidité.

• Ne pas poser d’objet contenant
du liquide, par exemple un
vase, sur l’appareil.

• Ne pas manipuler le cordon
d’alimentation avec les mains
mouillées.

• Lorsque l’interrupteur est sur
la position OFF, l’appareil n’est
pas complètement déconnecté
du SECTEUR (MAINS).

• L’appareil sera installé près de
la source d’alimentation, de
sorte que cette dernière soit
facilement accessible.

• Evitate di esporre l’unità a
temperature elevate.
Assicuratevi che vi sia
un’adeguata dispersione del
calore quando installate l’unità
in un mobile per componenti
audio.

• Manneggiate il cavo di
alimentazione con attenzione.
Tenete ferma la spina quando
scollegate il cavo dalla presa.

• Tenete l’unità lontana
dall’umidità, dall’acqua e dalla
polvere.

• Scollegate il cavo di
alimentazione quando
prevedete di non utilizzare
l’unità per un lungo periodo di
tempo.

• Non coprite i fori di
ventilazione.

• Non inserite corpi estranei
all’interno dell’unità.

• Assicuratevi che l’unità non
entri in contatto con insetticidi,
benzolo o solventi.

• Non smontate né modificate
l’unità in alcun modo.

• Le aperture di ventilazione
non devono essere ostruite
coprendole con oggetti, quali
giornali, tovaglie, tende e così
via.

• Non posizionate sull’unità fi
amme libere, come ad esempio
candele accese.

• Prestate attenzione agli aspetti
legati alla tutela dell’ambiente
nello smaltimento delle
batterie.

• L’apparecchiatura non deve
essere esposta a gocciolii o
spruzzi.

• Non posizionate sull’unità alcun
oggetto contenente liquidi,
come ad esempio i vasi.

• Non toccare il cavo di
alimentazione con le mani
bagnate.

• Quando l’interruttore
è nella posizione OFF,
l’apparecchiatura non è
completamente scollegata da
MAINS.

• L’apparecchio va installato
in prossimità della fonte di
alimentazione, in modo che
quest’ultima sia facilmente
accessibile.

• Evite altas temperaturas.
Permite la suficiente dispersión
del calor cuando está instalado
en la consola.

• Maneje el cordón de energía
con cuidado.
Sostenga el enchufe cuando
desconecte el cordón de
energía.

• Mantenga el equipo libre de
humedad, agua y polvo.

• Desconecte el cordón de
energía cuando no utilice el
equipo por mucho tiempo.

• No obstruya los orificios de
ventilación.

• No deje objetos extraños
dentro del equipo.

• No permita el contacto
de insecticidas, gasolina y
diluyentes con el equipo.

• Nunca desarme o modifique el
equipo de ninguna manera.

• La ventilación no debe quedar
obstruida por haberse cubierto
las aperturas con objetos
como periódicos, manteles o
cortinas.

• No deberán colocarse sobre
el aparato fuentes inflamables
sin protección, como velas
encendidas.

• A la hora de deshacerse de las
pilas, respete la normativa para
el cuidado del medio ambiente.

• No exponer el aparato al goteo
o salpicaduras cuando se
utilice.

• No colocar sobre el aparato
objetos llenos de líquido, como
jarros.

• No maneje el cable de
alimentación con las manos
mojadas.

• Cuando el interruptor está en la
posición OFF, el equipo no está
completamente desconectado
de la alimentación MAINS.

• El equipo se instalará cerca
de la fuente de alimentación
de manera que resulte fácil
acceder a ella.

• Vermijd hoge temperaturen.
Zorg er bij installatie in een
audiorack voor, dat de door het
toestel geproduceerde warmte
goed kan worden afgevoerd.

• Hanteer het netsnoer
voorzichtig.
Houd het snoer bij de stekker
vast wanneer deze moet
worden aan- of losgekoppeld.

• Laat geen vochtigheid,
water of stof in het apparaat
binnendringen.

• Neem altijd het netsnoer uit
het stopkontakt wanneer het
apparaat gedurende een lange
periode niet wordt gebruikt.

• De ventilatieopeningen mogen
niet worden beblokkeerd.

• Laat geen vreemde
voorwerpen in dit apparaat
vallen.

• Voorkom dat insecticiden,
benzeen of verfverdunner met
dit toestel in contact komen.

• Dit toestel mag niet
gedemonteerd of aangepast
worden.

• De ventilatie mag niet
worden belemmerd door
de ventilatieopeningen af
te dekken met bijvoorbeeld
kranten, een tafelkleed of
gordijnen.

• Plaats geen open vlammen,
bijvoorbeeld een brandende
kaars, op het apparaat.

• Houd u steeds aan de
milieuvoorschriften wanneer u
gebruikte batterijen wegdoet.

• Stel het apparaat niet bloot aan
druppels of spatten.

• Plaats geen voorwerpen gevuld
met water, bijvoorbeeld een
vaas, op het apparaat.

• Raak het netsnoer niet met
natte handen aan.

• Als de schakelaar op OFF
staat, is het apparaat niet
volledig losgekoppeld van de
netspanning (MAINS).

• De apparatuur wordt in de
buurt van het stopcontact
geïnstalleerd, zodat dit altijd
gemakkelijk toegankelijk is.

• Undvik höga temperaturer.
Se till att det finns möjlighet
till god värmeavledning vid
montering i ett rack.

• Hantera nätkabeln varsamt.
Håll i kabeln när den kopplas
från el-uttaget.

• Utsätt inte apparaten för fukt,
vatten och damm.

• Koppla loss nätkabeln om
apparaten inte kommer att
användas i lång tid.

• Täpp inte till
ventilationsöppningarna.

• Se till att främmande föremål
inte tränger in i apparaten.

• Se till att inte insektsmedel
på spraybruk, bensen och
thinner kommer i kontakt med
apparatens hölje.

• Ta inte isär apparaten och
försök inte bygga om den.

• Ventilationen bör inte
förhindras genom att täcka
för ventilationsöppningarna
med föremål såsom tidningar,
bordsdukar eller gardiner.

• Placera inte öppen eld, t.ex.
tända ljus, på apparaten.

• Tänk på miljöaspekterna när du
bortskaffar batterier.

• Apparaten får inte utsättas för
vätska.

• Placera inte föremål fyllda
med vätska, t.ex. vaser, på
apparaten.

• Hantera inte nätsladden med
våta händer.

• Även om strömbrytaren står
i det avstängda läget OFF,
så är utrustningen inte helt
bortkopplad från det elektriska
nätet (MAINS).

• Utrustningen ska vara
installerad nära strömuttaget
så att strömförsörjningen är lätt
att tillgå.

DEUTSCHFRANCAISITALIANOESPAÑOLNEDERLANDSSVENSKA ENGLISH

II

ENGLISH

FRANCAIS

ITALIANO ESPAÑOL NEDERLANDS SVENSKADEUTSCH

• DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product, to which

this declaration relates, is in conformity with the following standards:
EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3.
Following the provisions of Low Voltage Directive 2006/95/EC and

EMC Directive 2004/108/EC, the EC regulation 1275/2008 and its

frame work Directive 2009/125/EC for Energy-related Products (ErP).

• ÜBEREINSTIMMUNGSERKLÄRUNG

Wir erklären unter unserer Verantwortung, daß dieses Produkt, auf

das sich diese Erklärung bezieht, den folgenden Standards entspricht:
EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3.
Following the provisions of low voltage directive 2006/95/EC and

EMC directive 2004/108/EC, the EC regulation 1275/2008 and its

frame work directive 2009/125/EC for energy-related products (ErP).

• DECLARATION DE CONFORMITE

Nous déclarons sous notre seule responsabilité que l’appareil, auquel

se réfère cette déclaration, est conforme aux standards suivants:
EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3.
Selon la directive 2006/95/EC concernant la basse tension et la

directive CEM 2004/108/EC, la réglementation européenne 1275/2008

et la directive 2009/125/EC établissant un cadre de travail applicable

aux produits liés à l'énergie (ErP).

• DICHIARAZIONE DI CONFORMITÀ

Dichiariamo con piena responsabilità che questo prodotto, al quale la

nostra dichiarazione si riferisce, è conforme alle seguenti normative:
EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3.
Facendo seguito alle disposizioni della direttiva sul basso voltaggio

2006/95/EC alla direttiva EMC 2004/108/EC, alla norma EC 1275/2008

e alla relativa legge quadro 2009/125/EC in materia di prodotti

alimentati ad energia (ErP).
QUESTO PRODOTTO E’ CONFORME
AL D.M. 28/08/95 N. 548

• DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que este producto

al que hace referencia esta declaración, está conforme con los

siguientes estándares:
EN60065, EN55013, EN55020, EN61000-3-2 y EN61000-3-3.
De acuerdo con la directiva sobre baja tensión 2006/95/CE y la

directiva sobre CEM 2004/108/CE, la normativa CE 1275/2008 y su

directiva marco 2009/125/EC para productos relacionados con la

energía (ErP).

• EENVORMIGHEIDSVERKLARING

Wij verklaren uitsluitend op onze verantwoordelijkheid dat dit produkt,

waarop deze verklaring betrekking heeft, in overeenstemming is met

de volgende normen:
EN60065, EN55013, EN55020, EN61000-3-2 en EN61000-3-3.
Volgens de voorzieningen van lage spanningsrichtlijn 2006/95/

EC en EMC-richtlijn 2004/108/EC, de EU-richtlijn 1275/2008 en de

kaderrichtlijn 2009/125/EC voor energieverbruikende producten (ErP).

• ÖVERENSSTÄMMELSESINTYG

Härmed intygas helt på eget ansvar att denna produkt, vilken detta

intyg avser, uppfyller följande standarder:
EN60065, EN55013, EN55020, EN61000-3-2 och EN61000-3-3.
Uppfyller reglerna i lågspänningsdirektivet 2006/95/EC och

EMC-direktivet 2004/108/EC, EU-förordningen 1275/2008 och

ramverksdirektivet 2009/125/EC för energirelaterade produkter (ErP).

DENON EUROPE
Division of D&M Germany GmbH
An der Kleinbahn 18, Nettetal,
D-41334 Germany

III

A NOTE ABOUT RECYCLING:

This product’s packaging materials are recyclable and can be reused. Please
dispose of any materials in accordance with the local recycling regulations.
When discarding the unit, comply with local rules or regulations.
Batteries should never be thrown away or incinerated but disposed of in
accordance with the local regulations concerning battery disposal.
This product and the supplied accessories, excluding the batteries, constitute
the applicable product according to the WEEE directive.

HINWEIS ZUM RECYCLING:

Das Verpackungsmaterial dieses Produktes ist zum Recyceln geeignet und kann
wieder verwendet werden. Bitte entsorgen Sie alle Materialien entsprechend
der örtlichen Recycling-Vorschriften.
Beachten Sie bei der Entsorgung des Gerätes die örtlichen Vorschriften und
Bestimmungen.
Die Batterien dürfen nicht in den Hausmüll geworfen oder verbrannt werden;
bitte entsorgen Sie die Batterien gemäß der örtlichen Vorschriften.
Dieses Produkt und das im Lieferumfang enthaltene Zubehör (mit Ausnahme
der Batterien!) entsprechen der WEEE-Direktive.

UNE REMARQUE CONCERNANT LE RECYCLAGE:

Les matériaux d’emballage de ce produit sont recyclables et peuvent être
réutilisés. Veuillez disposer des matériaux conformément aux lois sur le recyclage
en vigueur.
Lorsque vous mettez cet appareil au rebut, respectez les lois ou réglementations en vigueur.
Les piles ne doivent jamais être jetées ou incinérées, mais mises au rebut conformément aux lois
en vigueur sur la mise au rebut des piles.
Ce produit et les accessoires inclus, à l’exception des piles, sont des produits conformes à la
directive DEEE.

NOTA RELATIVA AL RICICLAGGIO:

I materiali di imballaggio di questo prodotto sono riutilizzabili e riciclabili. Smaltire i materiali
conformemente alle normative locali sul riciclaggio.
Per lo smaltimento dell’unità, osservare le normative o le leggi locali in vigore.
Non gettare le batterie, né incenerirle, ma smaltirle conformemente alla normativa locale sui
rifiuti chimici.
Questo prodotto e gli accessori inclusi nell’imballaggio sono applicabili alla direttiva RAEE, ad
eccezione delle batterie.

ACERCA DEL RECICLAJE:

Los materiales de embalaje de este producto son reciclables y se pueden volver a utilizar.
Disponga de estos materiales siguiendo los reglamentos de reciclaje de su localidad.
Cuando se deshaga de la unidad, cumpla con las reglas o reglamentos locales.
Las pilas nunca deberán tirarse ni incinerarse. Deberá disponer de ellas siguiendo los reglamentos
de su localidad relacionados con los desperdicios químicos.
Este producto junto con los accesorios empaquetados es el producto aplicable a la directiva
RAEE excepto pilas.

EEN AANTEKENING MET BETREKKING TOT DE RECYCLING:

Het inpakmateriaal van dit product is recycleerbaar en kan opnieuw gebruikt worden. Er wordt
verzocht om zich van elk afvalmateriaal te ontdoen volgens de plaatselijke voorschriften.
Volg voor het wegdoen van de speler de voorschriften voor de verwijdering van wit- en bruingoed
op.
Batterijen mogen nooit worden weggegooid of verbrand, maar moeten volgens de plaatselijke
voorschriften betreffende chemisch afval worden verwijderd.
Op dit product en de meegeleverde accessoires, m.u.v. de batterijen is de richtlijn voor
afgedankte elektrische en elektronische apparaten (WEEE) van toepassing.

OBSERVERA ANGÅENDE ÅTERVINNING:

Produktens emballage är återvinningsbart och kan återanvändas. Kassera det enligt lokala
återvinningsbestämmelser.
När du kasserar enheten ska du göra det i överensstämmelse med lokala regler och bestämmelser.
Batterier får absolut inte kastas i soporna eller brännas. Kassera dem enligt lokala bestämmelser
för kemiskt avfall.
Denna apparat och de tillbehör som levereras med den uppfyller gällande WEEE-direktiv, med
undantag av batterierna.

n CAUTIONS ON INSTALLATION

VORSICHTSHINWEISE ZUR AUFSTELLUNG
PRÉCAUTIONS D’INSTALLATION
PRECAUZIONI SULL’INSTALLAZIONE
EMPLAZAMIENTO DE LA INSTALACIÓN
VOORZORGSMAATREGELEN BIJ DE

INSTALLATIE
FÖRSIKTIGHET VID INSTALLATIONEN

z

z z

Wall

z

Wand
Paroi
Parete
Pared
Muur
Vägg

z For proper heat dispersal, do not install this unit in a

confined space, such as a bookcase or similar enclosure.

• More than 0.3 m is recommended.

• Do not place any other equipment on this unit.

z Stellen Sie das Gerät nicht an einem geschlossenen Ort,

wie in einem Bücherregal oder einer ähnlichen Einrichtung
auf, da dies eine ausreichende Belüftung des Geräts
behindern könnte.

• Empfohlen wird über 0,3 m.

• Keine anderen Gegenstände auf das Gerät stellen.

z Pour permettre la dissipation de chaleur requise, n’installez

pas cette unité dans un espace confiné tel qu’une
bibliothèque ou un endroit similaire.

• Une distance de plus de 0,3 m est recommandée.

• Ne placez aucun matériel sur cet appareil.

z Per una dispersione adeguata del calore, non installare

questa apparecchiatura in uno spazio ristretto, come ad
esempio una libreria o simili.

• Si raccomanda una distanza superiore ai 0,3 m.

• Non posizionare alcun altro oggetto o dispositivo su questo
dispositivo.

z Para la dispersión del calor adecuadamente, no instale

este equipo en un lugar confinado tal como una librería o
unidad similar.

• Se recomienda dejar más de 0,3 m alrededor.

• No coloque ningún otro equipo sobre la unidad.

z Plaats dit toestel niet in een kleine afgesloten ruimte, zoals

een boekenkast e.d., omdat anders de warmte niet op
gepaste wijze kan worden afgevoerd.

• Meer dan 0,3 m is aanbevolen.

• Plaats geen andere apparatuur op het toestel.

z För att tillförsäkra god värmeavledning får utrustningen

inte installeras i instängda utrymmen, som t.ex. en
bokhylla eller liknande.

• Mer än 0,3 m rekommenderas.

• Placera ingen annan utrustning ovanpå den här enheten.

Getting started

Thank you for purchasing this DENON product. To ensure proper operation, please read these owner’s manual carefully before using the product.
After reading them, be sure to keep them for future reference.

ENGLISH

Contents

Getting started ·············································································· 1

Accessories ··················································································1
About this manual ·········································································1
Features ························································································2
Cautions on handling ····································································2

Simple version (Simple setup guide) ··························3

Basic version ··········································································12

Connections ·················································································13

Important information ·································································13
Connecting an HDMI-compatible device ····································14
Connecting a TV··········································································16
Connecting a Blu-ray Disc player / DVD player ···························16
Connecting a set-top box (Satellite tuner/cable TV) ····················17
Connecting a digital camcorder ··················································17
Connecting a control dock for iPod ·············································18
Connecting an antenna ·······························································18

Playback (Basic operation) ························································· 19

Important information ·································································19
Playing a Blu-ray Disc player/DVD player ····································20
Playing an iPod® ·········································································20
Tuning in radio stations ·······························································22

Selecting a listening mode (Surround mode) ··························25

Standard playback ·······································································25
DENON original surround playback ·············································27
Stereo playback ··········································································27
Direct playback ···········································································27

Advanced version ·······························································28

Speaker installation/connection (Other than 5.1-channel) ·····29

Install ··························································································29
Connect ······················································································30
Set up speakers ·········································································31

Playback (Advanced operation) ················································· 32

Convenient functions ··································································32

How to make detailed settings ··················································35

Menu map ··················································································35
Examples of on-screen display and front display ························36
Inputting characters ···································································37
Input Setup ·················································································38
Audio Adjust ···············································································43
Manual Setup··············································································48
Information ·················································································53

Operating the connected devices by remote control unit ······54

Operating AV equipment ····························································54
Registering preset codes ····························································54
Operating components ·······························································56
Resetting the remote control unit ···············································57

Information ·············································································58

Part names and functions···························································59

Front panel ··················································································59
Display ························································································59
Rear panel ···················································································60
Remote control unit ····································································61

Other information ·······································································63

Trademark information ································································63
Surround ·····················································································64
Explanation of terms ···································································68

Troubleshooting ··········································································70

Resetting the microprocessor ····················································72

Specifications ··············································································72

Accessories

Check that the following parts are supplied with the product.

q Owner’s manual ...................................................................... 1

w Service network list .................................................................1

e Power cord (Cord length: Approx. 1.7 m) ................................ 1

r Remote control unit (RC-1147) ................................................ 1

t R6/AA batteries .......................................................................2

y Setup microphone

(DM-A409, Cord length: Approx. 6.0 m) .................................. 1

u AM loop antenna ..................................................................... 1

i FM indoor antenna ..................................................................1

e r u iy

About this manual

n Operation buttons

The operations described in this manual are based mainly on
remote control operation.

n Symbols

v

NOTE

This symbol indicates a reference page on which
related information is described.

This symbol indicates a supplementary information
and tips for operations.

This symbol indicates points to remember operations
or function limitations.

Basic version Advanced versionSimple version Information

n Illustrations

Note that the illustrations in these instructions are for explanation
purposes and may differ from the actual unit.

1

ENGLISH

Features

Fully Discrete, identical quality and power for all
5 channels (110 W x 5ch)

The unit is equipped with a power amplifi er that plays back high­fi delity sound in surround mode with equal quality and power for all
channels, true to the original sound.
The power amplifi er circuit adopts a discrete-circuit confi guration
that achieves high-quality surround sound play back.

Supports HDMI 1.4 with 3D, ARC, Deep Color,
x.v.Color , Auto Lipsync and HDMI control function

This unit can output 3D video signals input from a Blu-ray Disc
player to a TV that supports a 3D system. This unit also supports
the ARC (Audio Return Channel) function, which plays back TV
sound with this unit via an HDMI cable used for connecting the
unit and a TVz.

zThe TV should support the ARC function.

4-HDMI inputs and 1-output

The unit is equipped with 4 HDMI input connectors for connecting
devices with HDMI connectors, such as a Blu-ray Disc player,
game machine, HD video camera, etc.

High Defi nition Audio Support

The unit is equipped with a decoder which supports high-quality
digital audio format for Blu-ray Disc players such as Dolby TrueHD,
DTS-HD Master Audio, etc.

Auto setup function

The unit is provided with an “Auto setup function” which
automatically makes speaker settings best suited for the listening
environment. The sound from the speakers is picked up with the
supplied microphone. Refl ecting sound and audio characteristics of
speakers are measured, and settings for an optimum sound fi eld
are automatically made.

Upconverting of all types of source video signals
to HDMI signals

This unit is provided with functions for automatic conversion of
various video signals (component video, S-Video, video) that are
input to this unit into HDMI signals for output to a monitor, allowing
connection between this unit and a TV to be made with a single
HDMI cable.

Dock connecrivity for iPod and network streaming

If an optional DENON control dock for iPod (ASD-3N, ASD-3W,
ASD-51N or ASD-51W) is connected to this unit, you can listen to
Internet radio or enjoy music and photos stored in your PC.

zAn Internet connection environment is required.

Cautions on handling

• Before turning the power switch on

Check once again that all connections are correct and that there are
no problems with the connection cables.

• Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When going on vacation or leaving home
for long periods of time, be sure to unplug the power cord from the
power outlet.

• About Condensation
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.

• Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If that
occurs, move the mobile phone away from this unit when it is in use.

• Moving the unit
Turn off the power and unplug the power cord from the power
outlet. Next, disconnect the connection cables to other system units
before moving the unit.

• About Care

• Wipe the cabinet and control panel clean with a soft cloth.

• Follow the instructions when using a chemical cleaner.

• Benzene, paint thinner or other organic solvents as well as

insecticide may cause material changes and discoloration if brought
into contact with the unit, and should therefore not be used.

Dolby Pro Logic gz

The unit is provided with a Dolby Pro Logic gz decoder. When you
play back the sound in Dolby Pro Logic gz playback, you can enjoy
playback sound with rich spacial expression.

Easy to use, On-Screen Display

Simple settings are enabled with the setting menus displayed on
the TV screen. When you control the sound volume, the volume
level is displayed on the screen, and when you switch the input
source, the name of the input source is displayed.

2

Simple
version

Here, we explain the entire setup procedure, from unboxing the unit to using it in a home theater.
The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers.
See page 29 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.

n Before connecting the unit, turn off the power to all devices.
n For operation of the connected devices, refer to the user manuals for each device.

Simple version (Simple setup guide)

ENGLISH

Basic version Advanced version InformationSimple version

1

Install

(vpage4)

Enjoy better audio, using
the correct install method.

2

Connect

(vpage4)

Connect 5.1-channel
speakers, a TV and Blu­ray Disc player equipped
with an HDMI connector.

3

Turn on
power

(vpage6)

4

Set up
speakers

(vpage6)

Use the setup microphone
(DM-A409) included with
the product, for automatic
setup.

5

Play back
disc

(vpage11)

Enjoy Blu-ray Disc and DVD
in surround sound.

Set Up Speakers (Audyssey® Auto Setup)

Step 2

Measurement

Preparation

Step 1

Speaker
Detection

Step 3

Calculating

Step 4

Check

Step 5

Store

Finish

3

ENGLISH

1

Install

1 2 4 53

Here, we explain setup using the example of 5.1-channel speaker
playback.

FL FR

SW

C

22 – 30˚

120˚

SL

Listening position

SR

2

Connect

Speakers

Carefully check the left (L) and right (R)
channels and + (red) and – (black) polarities
on the speakers being connected to the
this unit, and be sure to interconnect the
channels and polarities correctly.

Connecting the speaker cables

Peel off about 10 mm of sheathing from the tip
of the speaker cable, then either twist the core
wire tightly or terminate it.

1 2 4 53

NOTE

• Connect so that the speaker cable core wires
do not protrude from the speaker terminal.
The protection circuit may be activated if the
core wires touch the rear panel or if the + and –
sides touch each other (vpage69 “Protection
Circuit”).

• Never touch the speaker terminals while the
power supply is connected. Doing so could
result in electric shock.

• Use speakers with the speaker impedances
shown below.

Speaker terminals

FRONT

SURROUND

Speaker

impedance

6 – 16 ΩCENTER

FL Front speaker (L) • Install the surround speakers in a position
FR Front speaker (R)
C Center speaker
SW Subwoofer
SL Surround speaker (L)
SR Surround speaker (R)

4

The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers.

60 to 90 cm higher than ear level.

Surround

Front
speaker

speaker

60 – 90 cm

GViewed from the sideH

See page 29 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.

Audio cable
(sold separately)

ENGLISH

Connect

Blu-ray Disc player and TV

Use only an HDMI (High Definition Multimedia Interface) cable that bears the HDMI
logo (a certified HDMI product). Using a cable without the HDMI logo (an uncertified
HDMI product) may result in abnormal playback.
When outputting Deep Color or 1080p, etc., we recommend you use “High Speed
HDMI cable” or “High Speed HDMI cable with Ethernet” for enhanced high-quality
playback.

TV

Blu-ray Disc player

Basic version Advanced version InformationSimple version

SL

FL FR

SW

C

Subwoofer
with built-in
amplifier

Speaker cables

(sold separately)

SR

HDMI

OUT

HDMI cable

(sold separately)

To household power outlet

(AC 230 V, 50 Hz)

HDMI cable

(sold separately)

Power cord

(supplied)

HDMI

IN

NOTE

• Do not plug in the power cord until all connections have been completed.

• Do not bundle power cords together with connection cables. Doing so can result in humming or noise.

5

ENGLISH

3

1

Turn on power

Turn on the TV and subwoofer
power.

Power on

Change the TV input to the input of

2

this unit.

Press POWER ON to turn on power

3

to the unit.

The power indicator flashes green and the
power turns on.

Power on

1 2 4 53

4

The acoustic characteristics of the connected speakers and listening room are
measured and the optimum settings are made automatically. This is called
“Audyssey Auto Setup”.
To perform measurement, place the setup microphone in multiple locations all
around the listening area. For best results, we recommend you measure in six
positions, as shown in the illustration (up to six positions).

• When performing Audyssey Auto Setup, MultEQ®/Dynamic EQ®/Dynamic
Volume™ functions become active (vpage45, 46).

• To set up the speakers manually, use “Speaker Setup” (vpage48) on the menu.

NOTE

• Make the room as quiet as possible. Background noise can disrupt the room measurements. Close
windows, silence cell phones, televisions, radios, air conditioners, fluorescent lights, home appliances,
light dimmers, or other devices as measurements may be affected by these sounds.

• Cell phones should be placed away from all audio electronics during the measurement process as Radio
Frequency Interference (RFI) may cause measurement disruptions (even if the cell phone is not in use).

• Do not unplug the setup microphone from the main unit until Audyssey Auto Setup is completed.

• Do not stand between the speakers and setup microphone or allow obstacles in the path while the
measurements are being made. This will cause inaccurate readings.

• Loud test sounds may be played during Audyssey Auto setup. This is part of
normal operation. If there is background noise in room, these test signals will
increase in volume.

• Operating

• Measurement cannot be performed when headphones are connected.

Set up speakers
(Audyssey® Auto Setup)

VOL df during the measurements will cancel the measurements.

1 2 4 53

Power on

6

The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers.

See page 29 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.

ENGLISH

Set up speakers (Audyssey® Auto Setup)

About setup microphone placement

• Measurements are performed by placing the setup microphone
successively at multiple positions throughout the entire listening
area, as shown in GExample qH. For best results, we recommend
you measure in six positions, as shown in the illustration (up to six
positions).

• Even if the listening environment is small as shown in GExample wH,
measuring at multiple points throughout the listening environment
results in more effective correction.

GExample qH GExample wH

FL SW C FR

( : Measuring positions)

M

*

FL Front speaker (L) SW Subwoofer
FR Front speaker (R) SL Surround speaker (L)
C Center speaker SR Surround speaker (R)

SRSL

FL SW C FR

( : Measuring positions)

M

*

SRSL

About the main listening position (*M)

The main listening position is the position where listeners would
normally sit or where one would normally sit alone within the listening
environment. Before starting Audyssey Auto Setup, place the setup
microphone in the main listening position. Audyssey MultEQ® uses
the measurements from this position to calculate speaker distance,
level, polarity, and the optimum crossover value for the subwoofer.

1

Set up the microphone

Mount the setup microphone on a tripod or stand
and place it in the main listening position.

When placing the setup microphone, adjust the height of the
sound receptor to the level of the listener’s ear.

Sound receptor

NOTE

• Do not hold the setup microphone in your hand during
measurements.

• Avoid placing the setup microphone close to a seat back or wall as
sound reflections may give inaccurate results.

Setup
microphone

2

Set up the subwoofer

If using a subwoofer capable of the following
adjustments, set up the subwoofer as shown below.

n When using a subwoofer with a direct mode

Set the direct mode to “On” and disable the volume adjustment
and crossover frequency setting.

n When using a subwoofer without a direct mode

Make the following settings:

• Volume : “12 o’clock position”

• Crossover frequency :

“Maximum/Highest Frequency”

• Low pass filter : “Off”

• Standby mode : “Off”

3

Set up the remote control unit

n Set up the operation mode

Press AMP to set the remote control unit to amplier
operation mode.

Press AMP

Basic version Advanced version InformationSimple version

The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers.

See page 29 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.

7

ENGLISH

Set up speakers (Audyssey® Auto Setup)

Preparation

Connect the setup microphone to the

4

SETUP MIC jack of this unit.

When the setup microphone is
connected, the following screen is
displayed.

3-1.Audyssey Auto Setup
MultEQ

Please place microphone
at ear height at
main listening position.

Pre Assign:
Normal

Start

Cancel
[ENT]:Select [RTN]:Back

Here, we explain setup using the example of

5.1-channel speaker playback.
For settings other than 5.1-channel surround,
select “Pre Assign” and perform steps 3 to 4 of
“Set up speakers” (vpage31).

Use ui to select “Start” and then

5

press ENTER.

When measuring begins, a test tone is
output from each speaker.

• Measurement requires several minutes.

If “Cancel” is selected

“Cancel Auto Setup?” is displayed on the TV
screen. If “Yes” is selected, “Audyssey Auto
Setup” closes.

Step 1

Speaker Detection

• In step 1, you will perform measurements at the main listening position.

• This step automatically checks the speaker configuration and speaker size, and calculates the channel
level, distance, and crossover frequency. It also corrects distortion in the listening area.

The detected speakers are displayed.

6

Step1:Speaker Detection
MultEQ
Front Sp. :Yes
Center Sp. :Yes
Subwoofer :Yes
Surround Sp. :Yes
S.Back(Preout) :No

Next

Retry
[ENT]:Next

NOTE

If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.

Use ui to select “Next” and then

7

press ENTER.

NOTE

If “Caution” is displayed:

Go to “Error messages” (vpage 10), check
any related items, and perform the necessary
procedures.
If the problem is resolved, return and restart
“Audyssey Auto Setup”.

When performing Audyssey Auto
Setup over again

Press ui to select “Retry”, and then press

ENTER.

When measuring has stopped

q Press ui to select “Cancel”, then press

ENTER.

w Press o p to select “Yes”, then press ENTER.

Setting up the speakers again

Repeat the operation from step 4 of

Preparation

Step 2

Measurement

• In step 2, you will perform measurements at
multiple positions (two to six positions) other than
the main listening position.

• You can achieve a more effective correction of
distortion within the listening area by performing
measurements at multiple positions.

Move the setup microphone to

8

position 2, use ui to select “Next”,
and then press ENTER.

The measurement of the second position
starts. Measurements can be made in up to
six positions.

Step2:Measurement
MultEQ

Please place microphone
at ear height at
2nd listening position.

Next

Calculate
Cancel

[ENT]:Next

If you want to omit measurements from the next

.

position onward, select “Calculate”.
(Go to

Step 3 Calculating

Repeat step 8, measuring positions 3

9

to 6.

When measurement of position 6 is
completed, a “All the measurements were
finished.” message is displayed.

Step2:Measurement
MultEQ

All the measurements
were finished.

Calculate

Retry
Cancel

[ENT]:Calculate

)

8

Remote control operation

buttons

Move the cursor
(Up/Down/Left/Right)

Confirm the setting Return to previous menu

ENGLISH

Set up speakers (Audyssey® Auto Setup)

Step 3

Calculating

On the

10

to select “Calculate”, and then press

ENTER.

Measuring results are analyzed, and the
frequency response of each speaker in the
listening room is determined.

• Analysis takes several minutes to complete. The
time required for this analysis depends on the
number of speakers connected.
The more connected speakers there are, the
longer it takes to perform analysis.

Step 2

Step3:Calculating
MultEQ

Calculating
Please wait...

[----------]

screen, use ui

Step 4

Check

Use ui to select the item you want

11

to check, and then press ENTER.

Step4:Check
MultEQ

Please check the results
of the measured item.

Speaker Config.Check

Distance Check
Channel Level Check
Crossover Freq.Check
Next
[ENT]:Select

• Subwoofers may measure a greater reported
distance than the actual distance due to added
electrical delay common in subwoofers.

• If you want to check another item, press

RETURN.

Use ui to select “Next” and then

12

press ENTER.

NOTE

• If the result differs from the actual connection
status, or if “Caution!” is displayed, see “Error
messages” (vpage10). Then carry out Audyssey
Auto Setup again.

• If the result still differs from the actual connection
status after remeasurement or the error message
still appears, it is possible that the speakers
are not connected properly. Turn this unit off,
check the speaker connections and repeat the
measurement process from the beginning.

• If you change speaker positions or orientation,
perform Audyssey Auto Setup again to find the
optimal equalizer settings.

Step 5

Store

Use ui to select “Store” and then

13

press ENTER.

Save the measurement results.

Step5:Store
MultEQ

Please select “Store”
to store measurement
values.

Store

Cancel

[ENT]:Store

Step5:Store
MultEQ

Storing
Please wait...

[----------]

• Saving the results requires about 10 seconds.

• If you do not want to save the measurement
results, use ui to select “Cancel”, then select
“Yes” using o p. All the measured Audyssey
Auto Setup data will be erased.

NOTE

During saving of measurement results, be sure
not to turn off the power.

Finish

Unplug the setup microphone from

14

the unit’s SETUP MIC jack.

Set Dynamic Volume™.

15

Finish
MultEQ

Storing complete.
Auto Setup is now
finished.

Turn on Dynamic Volume?

Yes : No

[ ]:Select [ENT]:Exit

• For details of Dynamic Volume settings, see
page 46.

n When turning Dynamic Volume on

• Use o to select “Yes”, and then press ENTER.

The unit automatically enters “Evening” mode.

n When turning Dynamic Volume off

• Use p to select “No”, and then press ENTER.

NOTE

After performing Audyssey Auto Setup, do not
change the speaker connections or subwoofer
volume. In event of a change, perform Audyssey
Auto Setup again.

Basic version Advanced version InformationSimple version

Remote control operation

buttons

Move the cursor
(Up/Down/Left/Right)

Confirm the setting Return to previous menu

9

ENGLISH

too high or

Retry
Cancel

[ENT]:Retry

F

Ambient noise is

Level is too low.

Caution
MultEQ

Error messages

An error message is displayed if Audyssey® Auto Setup could not be completed due to speaker placement, the measurement environment, etc.
If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.

NOTE

Be sure to turn off the power before checking speaker connections.

Examples Error details Measures

Caution

MultEQ

F

Microphone:None
or
Speaker :None

Retry
Cancel

[ENT]:Retry

Caution
MultEQ

Front

R :None

Retry
Cancel

[ ]:Up/Down [ ]:CH

Caution
MultEQ

[ ]:Up/Down [ ]:CH

Skip

Front

L :Phase

Retry
Cancel
Skip

• The connected setup microphone is broken, or a
device other than the supplied setup microphone
is connected.

• Not all speakers could be detected.

• The front L speaker was not properly detected.

• There is too much noise in the room for accurate
measurements to be made.

• Speaker or subwoofer sound is too low for
accurate measurements to be made.

• The displayed speaker could not be detected. • Check the connections of the displayed speaker.

• The displayed is connected with the polarities
reversed.

• Connect the included setup microphone to the
SETUP MIC jack of this unit.

• Check the speaker connections.

• Either turn off any device generating noise or
move it away.

• Perform again when the surroundings are quieter.

• Check the speaker installation and the direction
in which the speakers are facing.

• Adjust the subwoofer’s volume.

• Check the polarities of the displayed speaker.

• For some speakers, this error message may
be displayed even if the speaker is properly
connected. If you are sure the connection is
correct, press ui to select “Skip”, then press

ENTER.

Parameter Check

This function enables you to check the measurement results and
equalizer characteristics after Audyssey Auto Setup.

Use ui to select “Parameter Check” and then

1

press ENTER.

Use ui to select the item you want to check, then

2

press ENTER.

3-2.Parameter Check

Speaker Config.Check

Distance Chenck
Channel Level Check
Crossover Freq.Check
EQ Check

Restore

[ENT]:Select [RTN]:Back

Speaker Config. Check

Distance Check

Channel Level Check

Crossover Freq. Check

EQ Check

• If “EQ Check” is selected in step 2, press
curve (“Audyssey” or “Audyssey Flat”) to be checked.
Use o p to switch the display between the different speakers.

Press RETURN.

3

The confirmation screen reappears. Repeat steps 2 and 3.

Retrieving Audyssey Auto Setup settings

If you set “Restore” to “Yes”, you can return to Audyssey Auto Setup
measurement result (value calculated at the start by MultEQ®) even
when you have changed each setting manually.

Check the speaker configuration.

Check the distance.

Check the channel level.

Check the crossover frequency.

Check the equalizer.

ui to select equalizing

10

Remote control operation

buttons

Move the cursor
(Up/Down/Left/Right)

Confirm the setting Return to previous menu

ENGLISH

5

1

2

Play back disc

Press BD to switch an input source
for a player used for playback.

Play the component connected to
this unit.

Make the necessary settings on the
player (language setting, subtitles
setting, etc.) beforehand.

Adjust the sound volume.

3

VOL d ··········································· Volume up
VOL f ······································ Volume down
MUTE ·················································· Muting

Set the listening mode.

Set the listening mode according to the playback contents

4

(cinema, music, etc.) or according to your liking (vpage 25
“Selecting a listening mode (Surround mode)”).

1 2 4 53

When power is switched to standby

Press POWER OFF.

GPower indicator status in standby modeH

• Normal standby : Off

• When “HDMI Control” is set to “ON” : Red

You can also switch the power to standby by
pressing ON/STANDBY on the main unit.

NOTE

During power standby, a minimal amount of power is consumed. To
totally cut off the power, remove the power cord from the power
outlet.

Basic version Advanced version InformationSimple version

Remote control operation

buttons

Move the cursor
(Up/Down/Left/Right)

Confirm the setting Return to previous menu

11

ENGLISH

Basic
version

Basic version

Here, we explain the connections and basic operation methods for this unit.

F Connections vpage13
F Playback (Basic operation) vpage19
F Selecting a listening mode (Surround mode) vpage25

12

n Refer to the pages indicated below for information on connecting and playing back the various

media and external devices.

Audio and video

TV
Blu-ray Disc player
DVD player
Set-top box (Satellite tuner or cable TV)
Game console
Digital camcorder
Control dock for iPod

Audio

Radio

For speaker connections, see page 4.

vpage14, 16
vpage14, 16 vpage20
vpage14, 16 vpage20
vpage14, 17
vpage14
vpage17
vpage18 vpage20

vpage18 vpage22

PlaybackConnection

–

–
–
–

PlaybackConnection

Connections

Important information

• Make connections as follows before using this unit. Select an appropriate connection type
according to the components to be connected.

• You may need to make some settings on this unit depending on the connection method. Refer to
each description for more information.

• Select the cables (sold separately) according to the components being connected.

Converting input video signals for output (Video conversion function)

This unit is equipped with four types of video input connectors (HDMI, Component video, S-Video and
video) and two types of video output connectors (HDMI and video).
Use the connectors corresponding to the components to be connected.
This function automatically converts various formats of video signals input to this unit into the formats used
to output the video signals from this unit to a monitor.

GFlow of video signalsH

Video device

This unit

Monitor

ENGLISH

NOTE

• Do not plug in the power cord until all connections have been completed.

• When making connections, also refer to the operating instructions of the other components being
connected.

• Be sure to connect the left and right channels properly (left with left, right with right).

• Do not bundle power cords together with connection cables. Doing so can result in noise.

• The video conversion function supports the NTSC, PAL, SECAM, NTSC 4.43, PAL-N, PAL-M and PAL-60
formats.

• Resolutions of HDMI-compatible TVs can be checked at “HDMI Monitor Information” (vpage53).

NOTE

• HDMI signals cannot be converted into analog signals.

• When a non-standard video signal from a game machine or some other source is input, the video
conversion function might not operate.

• Component video input signals cannot be converted into Video format.

Advanced versionSimple version InformationBasic version

Output

HDMI connector

Component video

connectors

S-Video connector

Video connector

Input

(IN)

HDMI connector

Component video

connectors

S-Video connector

Video connector

Output

(MONITOR OUT)

HDMI

connector

Video connector

Input

HDMI connector

Video connector

13

ENGLISH

Important information

How the on-screen display appears in accordance with the video
input signal

The way the on-screen display of the menus, status, etc., is displayed differs according to the type of video
signal input to this unit.

n When video signals are input from the HDMI or component video connector

• Menu: Switches to a screen with a black background and the menu is superimposedz.

• Status display: Not displayed.

z If you want to display the menus superimposed on the background image, input the same video signals

to the video connectors. When a menu is displayed, the picture switches to the one being input from
the video connectors and the menu is displayed superimposed over this picture.

n When video signals are input from the S-Video or video connector

• Menu: Menus are displayed superimposed over the background image.

• Status display: Displayed.

Examples of on-screen display

• Menu screen • Status display screen
When the input source is
switched

MENU

[Auto]
IN :DVD

[ENT]:Select

MODE:STEREO

Status display: The operating status appears briefly on the screen

when the input source is switched or the volume is
changed.

• When the volume is adjusted

Master Volume -80.0dB

Connecting an HDMI-compatible device

You can connect up to five HDMI-compatible devices to the unit.

HDMI function

This unit supports the following HDMI functions:

• High resolution video signal

• 3D

• Deep Color (vpage68)

• Auto Lip Sync (vpage50)

• x.v.Color, sYCC601 color, Adobe RGB color, Adobe YCC601color (vpage68, 69)

• High definition digital audio format

• ARC (Audio Return Channel)

• Content Type

• CEC (HDMI control)

Copyright protection system

In order to play back digital video and audio such as BD-Video or DVD-Video via HDMI connection, both
this unit and TV or the player need to support the copyright protection system known as HDCP (High­bandwidth Digital Content Protection System). HDCP is copyright protection technology comprised of
data encryption and authentication of the connected AV device. This unit supports HDCP.

• If a device that does not support HDCP is connected, video and audio are not output correctly. Read
the owner’s manual of your television or player for more information.

About HDMI cables

• When a device supporting Deep Color signal transfer is connected, use a cable compatible “High Speed
HDMI cable” or “High Speed HDMI cable with Ethernet”

• When the ARC function is used, connect a device with a ”Standard HDMI cable with Ethernet” or “High
Speed HDMI cable with Ethernet” for HDMI 1.4.

HDMI control function (vpage32)

This function allows you to operate external devices from the receiver and operate the receiver from
external devices.

NOTE

• The HDMI control function may not work depending on the device it is connected to and its settings.

• You cannot operate a TV or Blu-ray Disc player / DVD player that is not compatible with the HDMI control
function.

14

About 3D function

This unit supports input and output of 3D (3 dimensional) video signals of the HDMI 1.4 standards, For
playing the 3D video content, a player, and a TV that support the 3D function of the HDMI 1.4 standards
are required in addition to this unit.

About ARC (Audio return channel) function

The Audio Return Channel in HDMI 1.4 enables a TV, via a single HDMI cable, to send audio data “upstream”
to this unit, increasing user flexibility and eliminating the need for any separate S/PDIF audio connection.

NOTE

To enable the ARC function,set “HDMI Control” to “ON” (vpage50).

About Content Type

The HDMI Specification Version 1.4 enables simple, automated picture setting selection with no user
intervention.
The Content Type feature enables the display to auto-select the correct viewing mode to match the content
type it is currently receiving from the source device, and to switch modes when a new content source is
selected. Content Type supports content profiles for gaming, movie, photograph, and text viewing modes.

NOTE

To enable the Content type, set “Video Mode” to “Auto” (vpage41).

Cables used for connections

Audio and video cable (sold separately)

HDMI cable

• This interface allows transfer of digital video signals and digital audio signals over a single HDMI cable.

Blu-ray Disc

player

HDMI

OUT

DVD player TV

HDMI

OUT

Set-top box

HDMI
OUT

Game

console

HDMI

OUT

HDMI

IN

ENGLISH

Connecting an HDMI-compatible device

• When this unit is connected to other devices with HDMI cables, connect this unit and TV also with an
HDMI cable.

• When connecting a device that supports Deep Color transmission, please use a “High Speed HDMI
cable” or “High Speed HDMI cable with Ethernet”.

• Video signals are not output if the input video signals do not match the monitor’s resolution. In this case,
switch the Blu-ray Disc/DVD player’s resolution to a resolution with which the monitor is compatible.

• When this unit and monitor are connected with an HDMI cable, if the monitor is not compatible with
HDMI audio signal playback, only the video signals are output to the monitor.

NOTE

The audio signal from the HDMI output connector (sampling frequency, number of channels, etc.) may be
limited by the HDMI audio specifications of the connected device regarding permissible inputs.

Connecting to a device equipped with a DVI-D connector

When an HDMI/DVI conversion cable (sold separately) is used, the HDMI video signals are converted to
DVI signals, allowing connection to a device equipped with a DVI-D connector.

NOTE

• No sound is output when connected to a device equipped with a DVI-D connector. Make separate audio
connections.

• Signals cannot be output to DVI-D devices that do not support HDCP.

• Depending on the combination of devices, the video signals may not be output.

n Settings related to HDMI connections

Set as necessary. For details, see the respective reference pages.

Advanced versionSimple version InformationBasic version

Input Assign (vpage40)

Set this to change the HDMI input connector to which the input source is assigned.

HDMI Setup (vpage50)

Make settings for HDMI video/audio output.

• Auto Lip Sync

• HDMI Audio Out

• HDMI Control

• Standby Source

• Power Off Control

NOTE

The audio signals output from the HDMI connectors are only the HDMI input signals.

15

ENGLISH

Connecting a TV

• Select the connector to use and connect the device.

• For video connections, see “Converting input video signals for output (Video conversion function)”
(vpage13).

• For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage14).

To listen to TV audio through this device, use the optical digital connection.

NOTE

This connection is not required when a TV compatible with the ARC function (Audio Return Channel (HDMI

1.4 standard function)) is connected to this unit via an HDMI connection.

For details, see “About ARC (Audio return channel) function” (vpage15) or refer to the instruction manual
for your TV.

Cables used for connections

Video cable (sold separately)

Video cable

Optical cable

TV

VIDEO

VIDEO

IN

AUDIO

OPTICAL

OUT

(Yellow)

Audio cable (sold separately)

Connecting a Blu-ray Disc player / DVD player

• You can enjoy video and audio from a Blu-ray Disc or DVD.

• Select the connector to use and connect the device.

• For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage14).

Cables used for connections

Video cable (sold separately)

Video cable

Audio cable

Blu-ray Disc player /

DVD player

VIDEO AUDIO

VIDEO

OUT

(Yellow)

Audio cable (sold separately)

(White)

(Red)

AUDIO

OUT

RL

R

L

R

L

L

R

L

R

in Set as Necessary

Set this to change the digital input connector to which the input source is assigned.
“Input Assign” (vpage40)

16

in Set as Necessary

Set this to change the digital input connector to which the input source is assigned.
“Input Assign” (vpage40)

For HD audio (Dolby TrueHD, DTS-HD, Dolby Digital Plus and DTS Express) playback, connect with HDMI
(vpage14 “Connecting an HDMI-compatible device”).

ENGLISH

Connecting a set-top box (Satellite tuner/cable TV)

• You can watch satellite or cable TV.

• Select the connector to use and connect the device.

• For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage14).

Cables used for connections

Video cables (sold separately)

Video cable

Component
video cable

Audio cable

Coaxial
digital cable

Satellite Tuner/Cable TV

COMPONENT VIDEO

Y P

(Yellow)

(Green)

(Blue)

(Red)

Audio cables (sold separately)

L

R

COAXIAL

OUT

OUT

VIDEO

B PR

(White)

(Red)

(Orange)

VIDEO

OUT

AUDIO

AUDIO

OUT

L

L

R

RL

R

Connecting a digital camcorder

• You can enjoy video and audio from a digital camcorder.

• For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage14).

Cables used for connections

Video cable (sold separately)

Video cable

Audio cable

VIDEO

(Yellow)

Audio cable (sold separately)

(White)

(Red)

Digital camcorder

AUDIOVIDEO

OUT

AUDIO

OUT

L

L

RL

R

R

L

R

L

R

Advanced versionSimple version InformationBasic version

R

L

in Set as Necessary

Set this to change the digital input connector or component video input connector to which the input
source is assigned.

“Input Assign” (vpage40)

in Set as Necessary

Set this to change the digital input connector to which the input source is assigned.
“Input Assign” (vpage40)

You can enjoy games by connecting a game machine via the V.AUX input connector. In this case, set the
input source to “V.AUX”.

NOTE

When a non-standard video signal from a game machine or some other source is input, the video conversion
function might not operate. In this case, use the monitor output of the same connector as the input.

17

ENGLISH

Connecting a control dock for iPod

• Connect a control dock for iPod to the unit to enjoy video and music
stored on an iPod.

• For a control dock for iPod, use ASD-1R, ASD-11R, ASD-3N, ASD­3W, ASD-51N and ASD-51W made by DENON (sold separately).

• For instructions on the control dock for iPod settings, refer to the
control dock for iPod’s operating instructions.

Control dock for iPod

ASD-51N

R

L

z

R

L

Connecting an antenna

• Connect the FM antenna or AM loop antenna supplied with the unit to enjoy listening to radio broadcasts.

• After connecting the antenna and receiving a broadcast signal (vpage22 “Listening to FM/AM broadcasts”), fix the antenna with tape in a
position where the noise level becomes minimal.

AM loop antenna

(supplied)

Black White

75 Ω Coaxial

cable

FM indoor

antenna

(supplied)

FM outdoor
antenna

Ground

AM outdoor

antenna

w eq

n Using the AM loop antenna

Suspending on a wall

Suspend directly on a wall without assembling.

zUse the AV/Control Cable supplied with the DENON
control dock for iPod.

in Set as Necessary

Set this to change the digital input connector to which the input
source is assigned.
“Input Assign” (vpage40)

18

n AM loop antenna assembly

Put the stand section

1

through the bottom of the
loop antenna from the
rear and bend it forward.

Insert the projecting part

2

into the square hole in
the stand.

Loop

antenna

Stand
Square

hole
Projecting

part

Nail, tack, etc.

Standing alone

Use the procedure shown left to assemble.

NOTE

• Do not connect two FM antennas simultaneously.

• Even if an external AM antenna is used, do not disconnect the AM
loop antenna.

• Make sure the AM loop antenna lead terminals do not touch metal
parts of the panel.

• If the signal has noise interference, connect the ground terminal
(GND) to reduce noise.

• If you are unable to receive a good broadcast signal, we recommend
installing an outdoor antenna. For details, inquire at the retail store
where you purchased the unit.

Playback (Basic operation)

ENGLISH

n Selecting the input source (vpage19)
n Adjusting the master volume (vpage19)
n Turning off the sound temporarily (vpage19)

n Playing a Blu-ray Disc player/DVD player

(vpage20)

n Playing an iPod® (vpage20)
n Tuning in radio stations (vpage22)

Selecting a listening mode (Surround mode)

(vpage25)

Playback (Advanced operation) (vpage32)

Important information

Before starting playback, make the connections between the different
components and the settings on the receiver.

NOTE

Also refer to the operating instructions of the connected components
when playing them.

Selecting the input source

Press the input source select button
(iPod, DVD, BD, TUNER, DOCK, SAT/

, GAME, V.AUX, TV) to be played

CBL

back.

The desired input source can be selected
directly.

• When iPod PLAY is pressed, the input
source of this unit is switched to “DOCK”
and the connected iPod is automatically
played (vpage21 “iPod play function”).

You can also use the following operation to select an input
source.

n Using the “Source Select” menu

q Press SOURCE SELECT.

Display the “Source Select” menu.

Source Select

TUNER

BD
DVD
TV

[ ]:Source
[ENT]:Select

w Use uio p to select the input source,

then press ENTER.

The input source is set and the source

selection menu is turned off.

• Input sources that are not going to be used can be set ahead of time.
Make this setting at “Source Delete” (vpage51).

• To turn off the source selection menu without selecting an input
source, press SOURCE SELECT again.

SAT/CBL
GAME
V.AUX
DOCK

The currently selected input source
is highlighted.

n Using the knob on the main unit

Turn SOURCE SELECT.

• Turning SOURCE SELECT switches
the input source, as shown below.

• If “Tuning Preset” mode is selected
for the input source, press SOURCE
before turning SOURCE SELECT.

BD DVD TV SAT/CBL

GAMEV.AUXDOCKTUNER

Adjusting the master volume

Use VOL df to adjust the volume.

n When the “Volume Display” setting

(vpage51) is “Relative”

GAdjustable rangeH

– – –

–80.5dB – 18.0dB

n When the “Volume Display” setting (vpage51) is

“Absolute”

GAdjustable rangeH

• The variable range differs according to the input signal and channel
level setting.

You can also operate via the main unit.
In this case, perform the following
operations.
Turn MASTER VOLUME to adjust the
volume.

0.0 – 99.0

Turning off the sound temporarily

Press MUTE.

• The sound is reduced to the level set at “Mute Level” (vpage51).

• To cancel, press MUTE again. Muting can also be canceled by
adjusting the master volume.

Advanced versionSimple version InformationBasic version

19

ENGLISH

Track Sel ectTrack Sel ectTrack Sel ect

Playing a Blu-ray Disc player/DVD
player

The following describes the procedure for playing Blu-ray Disc player/
DVD player.

Prepare for playback.

q Turn on the power of the TV,

1

2
3

4

subwoofer and player.

w Change the TV input to the input of

this unit.

e Load the disc in the player.

Press POWER ON to turn on
power to the unit.

Press BD or DVD to switch an
input source for a player used for
playback.

Play the component connected to this unit.

Make the necessary settings on the player (language setting,
subtitles setting, etc.) beforehand.

Playing an iPod

You can play back both video, photo and audio.

Listening to music on an iPod

DENON Control dock for iPod usable on this unit

• ASD-1R/ASD-11R/ASD-3N/ASD-3W/ASD-51N/ASD-51W

®

®

Prepare for playback.

q Connect the DENON control dock for iPod to this unit

1

(vpage18 “Connecting a control dock for iPod”).

w Set the iPod

®

in the DENON control dock for iPod.

Press POWER ON to turn on power to the unit.

2

Press DOCK to switch the input source to “DOCK”.

3

• If “Browse mode” is selected in step 4, the following screen is
displayed on a TV screen, depending on the connected control
dock for iPod.

GWhen using an ASD-1RH GWhen using an ASD-11RH

Music

Playlists

Artists
Albums
Songs
Genres
Composers

[ 1/6 ]

GWhen using an ASD-3N, ASD-3W, ASD-51N and ASD-51WH

iPod

Music
Video

Up/Down Sel ect

iPod

Music

Videos

[ 1/2 ]

Press SEARCH and hold it down for 2 seconds or

4

more to select the display mode.

• There are two modes for displaying the contents recorded on the
iPod.

Browse mode

• English letters, numbers and certain symbols are displayed.
Incompatible characters are displayed as “.” (period).

Remote mode

• “Remote iPod” or “Dock Remote” is displayed on the display
of this unit.

Display mode

Playable
files

Active
buttons

z1 When using an ASD-11R, ASD-3N, ASD-

3W, ASD-51N or ASD-51W DENON
control dock for iPod.

z2 Video may not be output, depending on

the combination of ASD-1R, ASD-11R,
ASD-3N, ASD-3W, ASD-51N or ASD­51W DENON control dock for iPod and
iPod.

Display iPod information on the TV screen.

Display iPod information on the iPod screen.

Browse mode Remote mode

Music file
Photo file
Video file
Remote

control unit
(This unit)

®

iPod

P P

z1

P

P P

P
P

P

z2

z2

Use ui to select the item, then

5

press ENTER or p to select the
le to be played.

20

• In “Browse mode”, the iPod display is as
shown at right.

NOTE

If the connections screen is not displayed,
the iPod may not be properly connected.
Reconnect it.

OK to disconnect.

Press ENTER, p or 1.

6

Playback starts.