Denon AVR-1602, AVR-682 Service Manual
For U.S.A., Canada, Europe,
Asia, China, Hong Kong &
Taiwan R.O.C. model
SERVICE MANUAL
Hi-Fi Component
MODEL
AVR-1602/682
AV SURROUND RECEIVER
Some illustrations using in this service manual are slightly different from the actual set.
14-14, AKASAKA 4-CHOME, MINATO-KU, TOKYO 107-8011 JAPAN
Telephone: 03 (3584) 8111
X0116 1174 NC 0111
AVR-1602/682
SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.
LEAKAGE CURRENT CHECK
Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the unit is defective.
SPECIFICATIONS
Audio Section
Power Amplifier
Rated output: Front: 70W+70W (8Ω/ohms, 20Hz~20kHz with 0.08% T.H.D )
Center: 70W (8Ω/ohms, 20Hz~20kHz with 0.08% T.H.D )
Surround: 70W+70W (8Ω/ohms, 20Hz~20kHz with 0.08% T.H.D )
Output terminals: Front: A or B 6 to 16W/ohms
Center/Surround: 6 to 16W/ohms
Analog
LINE input - PRE OUT
Input sensitivity/input impedance:
Frequency response: 10Hz~100kHz: +1, −3dB (TONE DEFEAT ON)
S/N ratio: 98dB (IHF-A weighted) (TONE DEFEAT ON)
200mV/47kΩ/kohms
100W+100W (6Ω/ohms, 1kHz with 0.7% T.H.D )
110W+110W (6Ω/ohms, EIAJ ) (Asia Model)
100W (6Ω/ohms, 1kHz with 0.7% T.H.D )
110W (6Ω/ohms, EIAJ ) (Asia Model)
100W+100W (6Ω/ohms, 1kHz with 0.7% T.H.D )
110W+110W (6Ω/ohms, EIAJ ) (Asia Model)
A+B 12 to 16W/ohms
(U.S.A., Canada & Europe Models)
(U.S.A., Canada & Europe Models)
(U.S.A., Canada & Europe Models)
Video Section
Standard video jacks
Input/output level and impedance:
Frequency response: 5Hz~10MHz +1, −3dB
1Vp-p,75Ω/ohms
S-video jacks (U.S.A., Canada & Asia Models)
Input/output level and impedance:
Frequency response: 5Hz~10MHz: +1, −3dB
Tuner section
Receiving range: [FM] (note: µV at 75Ω/ohms, 0dBf =1×10
U.S.A., Canada Models:
Europe & Asia (for China) Models:
Asia (for Multiple voltage) Models:
Usable sensitivity: 1.0µV (11.2dBf) 18µV
50 dB quieting sensitivity: MONO 1.6µV (15.3dBf)
S/N ratio: MONO 80dB (IHF-A weighted)
Total harmonic distortion: MONO 0.15% (1kHz)
General
Power supply:
U.S.A., Canada Models AC120V,60Hz
Europe Model AC230V,50Hz
Asia(for Multiple voltage)Model AC115/230V,50/60Hz
Asia(for China)Model AC220V,50Hz
Power consumption: 3.7A (USA & Canada model), 200W (Europe & Asia model)
Maximum external dimensions: 434 (W) × 147 (H) × 417 (D) mm (17-3/32″ × 5-25/32″ × 16-7/16″)
Mass: 9.8kg (20 lbs 9.7 oz)
Y(brightness)signal 1Vp-p, 75Ω/ohms
C(color)signal 0.286Vp-p, 75Ω/ohms
-15
87.50MHz~107.90MHz 520kHz~1710kHz
87.50MHz~108.00MHz 522kHz~1611kHz
87.50MHz~107.90MHz (0.2MHz steps) 520kHz~1710kHz (10kHz steps)
87.50MHz~108.00MHz (0.05MHz steps) 522kHz~1611kHz (9kHz steps)
STEREO 23µV (38.5dBf)
STEREO 75dB (IHF-A weighted)
STEREO 0.3% (1kHz)
W) [AM]
Remote control unit (RC-896)
Batteries: R6P/AA Type (two batteries)
External dimensions: 54 (W) × 172.5 (H) × 29 (D) mm (2-1/8″ × 6-51/64″ × 1-9/64″)
Mass: 120g (Approx. 4.2 oz) (including batteries)
* For purposes of improvement, specifications and design are subject to change without notice.
2
DISASSEMBLY
(Follow the procedure below in reverse order when reassembling)
Top Cover
Remove 6 screws 1 and 3 screws 2, detach the Top Cover
in the arrow direction.
1
AVR-1602/682
Top Cover
2
1
Front Panel
1. Remove 4 screws 3 and 2 screws 4.
2. Detach the Front Panel in the arrow direction.
Rear Panel
1. Remove cord bushing 5 from the Rear Panel.
2. Remove 31 screws 6.
3. Detach the Rear Panel in the arrow direction.
4
Front Panel
3
5
Rear Panel
6
6
3
LEVEL DIAGRAM
1
AVR-1602/682
2
3
4
5
76
8
A
B
C
D
E
4
BLOCK DIAGRAM
1
AVR-1602/682
2
3
4
5
76
8
A
B
C
D
E
5
ADJUSTMENT
Tuner Section
CONNECTION DIAGRAM OF MEASURING INSTRUMENTS
FM
T402 T403
R471
IC402
AVR-1602/682
STEREO
MODULATOR
VR402
TUNER B'D
FM ALIGNMENT
Alignment
Step
AM
Item
Center
1
Adjustment
2 Distortion
3 Repeat Steps 1 and 2
4 Signal Level
Tuning
Frequency
Setting
98.1MHz
(98.0MHz)
98.1MHz
(98.0MHz)
98.1MHz
(98.0MHz)
Type Frequency
FM SSG 98.1MHz 60dBP
FM SSG 98.1MHz 60dBP
FM SSG 98.1MHz 20dBP OFF
Input Output Adjustment
Input
Level
Modulation Coupling Type Connect to Points Adjust to
Mono
1kHz 100%
Mono
1kHz 100%
75ohm
Antenna
Terminal
Antenna
Terminal
Antenna
Terminal
FM SSG
Digital
Voltmeter
Digital
Volt me te r
Distortion
Meter
Light “TUNED” on
Terminal (L)
FL Display
R471 T402 r 50mV
Output
T403
VR402
Minimum
Distortion
+14
20
−10
dB
AM ALIGNMENT
Step
1 Signal Level
Alignment
Item
Frequency Input
999 (1000)
kHz
AM SSG VR401
T402 T403
R471
IC402
VR401
TUNER B’D
Output Adjustment
Type Connect to Points Adjust to
Light “TUNED” on
FL Display
Remarks
SSG OUTPUT
74dBP (EMF)
6
AVR-1602/682
Audio Section
Idling Current
Required measurement equipment : DC Voltmeter
Preparation
(1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room tempereture
15 °C ~ 30 °C (59 °F ~ 86 °F).
(2) Presetting
● POWER (Power sourse switch) → OFF
● SPEAKER (Speaker terminal) → No load (Do not connect speaker, dummy resistor, etc.)
Adjustment
(1) Remove top cover and set VR101, VR102, VR103, VR104, VR105 on Amp. Unit at full counterclockwise ( )
position.
(2) Connect DC Voltmeter to test points (FRONT-Lch: TP104, FRONT-Rch: TP105, CENTER ch: TP103,
SURROUND-Lch: TP101, SURROUND-Rch: TP102).
(3) Connect power cord to AC Line, and turn power switch "ON".
(4) Presetting. MASTER VOLUME : "---" counterclockwise (
MODE : 5CH STEREO
FUNCTION : CD
(5) Within 2 minutes after the power on, turn VR101 clockwise (
DC.
(6) After 10 minutes from the preset above, turn VR101 to set the voltage to 2.5 mV ±0.5 mV DC.
(7) Adjust the Variable Resistors of other channels in the same way.
min.)
) to adjust the TEST POINT voltage to 1.5 mV ±0.5 mV
7
SEMICONDUCTORS
IC’s
CS49326-CL
(IC812)
A0,SCCLK
DATA7,EMAD7,GPIO7
DATA6,EMAD6,GPIO6
DATA5,EMAD5,GPIO5
DATA4,EMAD4,GPIO4
DATA3,EMAD3,GPIO3
DATA2,EMAD2,GPIO2
DATA1,EMAD1,GPIO1
DATA0,EMAD0,GPIO0
VD2
DGND2
AVR-1602/682
A1,SCDIN
RD,R/W,EMOE,GPIO11
WR,DS,EMWR,GPIO10
AUDATA3,XMT958
DGND1
VD1
MCLK
SCLK
LRCLK
AUDATA0
AUDATA1
21 22
ABOOT,INTREQ
44
404142
43
1234
VD3
DGND3
SDATAN1
EXTMEM,GPIO8
39
AUDATA2
38
DC
37
DD
RESET
36
AGND
35
34
VA
FILT1
33
32
FILT2
CLKSEL
31
CLKIN
30
CMPREQ,LRCLKN2
29
282726252423
LRCLKN1
CMPCLK,SCLKN2
SCLKN1,STCCLK2
56
7
8
9
10
11
12
13
14
15
16
17
18 19 20
CS
CS49326-CL Terminal Function
Pin
No.
Pin Name
SCDIO,SCDOUT,PSEL,GPIO9
CMPDAT,SDATAN2,RCV958
Function
1 VD1 Digital positive supply
2 DGND1 Digital supply ground
3 AUDATA3, XMT958 SPDIF transmitter output, Digital audio output 3
4 WR, DS, EMWR, GPIO10 Host write strobe or host data strobe or external memory write enable or general purpose input & output number 10
5 RD, R/W, EMOE, GPIO11
Host parallel output enable or host parallel R/W or external memory output enable or general purpose input & output number11
6 A1, SCDIN Host address bit one or SPI serial control data input
7 A0, SCCLK Host parallel address bit zero or serial control port clock
8 DATA7, EMAD7, GPIO7
9 DATA6, EMAD6, GPIO6
10 DATA5, EMAD5, GPIO5
11 DATA4, EMAD4, GPIO4
12 VD2 Digital positive supply
13 DGND2 Digital supply ground
14 DATA3, EMAD3, GPIO3
15 DATA2, EMAD2, GPIO2
16 DATA1, EMAD1, GPIO1
17 DATA0, EMAD0, GPIO0
18 CS Host parallel chip select, host serial SPI chip select
19 SCDIO, SCDOUT, PSEL, GPIO9 Serial control port data input and output, parallel port type select
20 INTREQ, ABOOT Control port interrupt request, automatic boot enable
21 EXTMEM, GPIO8 External memory chip select or general purpose input & output number 8
22 SDATAN1 PCM audio data input number one
23 VD3 Digital positive supply
24 DGND3 Digital supply ground
25 SCLKN1, STCCLK2 PCM audio input bit clock
26 LRCLKN1 PCM audio input sample rate clock
27 CMPDAT, SDATAN2, RCV958 PCM audio data input number two
28 CMPCLK, SCLKN2 PCM audio input bit clock
29 CMPREQ, LRCLKN2 PCM audio input sample rate clock
30 CLKIN Master clock input
31 CLKSEL DSP clock select
32 FILT2 Phase locked loop filter
33 FILT1 Phase locked loop filter
34 VA Analog positive supply
35 AGND Analog supply ground
36 RESET Master reset input
37 DD Reserved
38 DC Reserved
39 AUDATA2 Digital audio output 2
40 AUDATA1 Digital audio output 1
41 AUDATA0 Digital audio output 0
42 LRCLK Audio output sample rate clock
43 SCLK Audio output bit clock
44 MCLK Audio master clock
8
AVR-1602/682
LC89055W (IC810)
LC89055W Terminal Function
Pin
No.
1 DISEL I Data input terminal (select input pin of DIN0, DIN1)
2 DOUT O Input bi-phase data through output terminal
3 DIN0 I Amp built-in coaxial/optical input correspond data input terminal
4 DIN1 I Amp built-in coaxial/optical input correspond data input terminal
5 DIN2 I Optical input correspond data input terminal
6 DGND Digital GND
7 DVDD Digital power supply
8 R I VCO gain control input terminal
9 VIN I VCO free-run frequency setting input terminal
10 LPF O PLL loop filter setting terminal
11 AVDD Analog power supply
12 AGND Analog GND
13 CKOUT O Clock output terminal (256fs, 384fs, 512fs, X’tal osc., VCO free-run osc.)
14 BCK O 64fs clock output terminal
15 LRCK O fs clock output terminal (L: Rch, H: Lch, I2S: Reverse)
16 DATAO O Data output terminal
17 XSTATE O Input data detecting result output terminal
18 DGND Digital GND
19 DVDD Digital power supply
20 XMCK O X’tal osc. clock output terminal (24.576MHz or 12.288MHz)
21 XOUT O X’tal osc. connection output terminal
22 XIN I X’tal osc. connection input terminal, external signal input possible (24.576MHz or 12.288MHz)
23 EMPHA O Emphasis information output terminal of channel status
24 AUDIO O Bit1 output terminal of channel status
25 CSFLAG O Top 40bit revise flag output terminal of channel status
26 F0/P0/C0 O Input fs cal. sig. out/data type out/input word inf. output terminal
27 F1/P1/C1 O Input fs cal. sig. out/data type out/input word inf. output terminal
28 F2/P2/C2 O Input fs cal. sig. out/data type out/input word inf. output terminal
29 VF/P3/C3 O Validity flag out/data type out/input word inf. output terminal
30 DVDD Digital power supply
31 DGND Digital GND
32 AUTO O Non PCM burst data transfer detect sig. output terminal
33 BPSYNC O Non PCM burst data preamble Pa, Pb, Pc, Pd sync sig. output terminal
34 ERROR O PLL lock error, data error flag output terminal
35 DO O CPU/IFD read data output terminal
36 DI I CPU I/F write data input terminal
37 CE I CPU I/F chip enable input terminal
38 CL I CPU I/F chip enable input terminal
39 XSEL I Frequency select input pin of XIN X’tal osc. (24.576MHz or 12.288MHz)
40 MODE0 I Mode setting input terminal
41 MODE1 I Mode setting input terminal
42 DGND Digital GND
43 DVDD Digital power supply
44 DOSEL0 I Data output format select input terminal
45 DOSEL1 I Data output format select input terminal
46 CKSEL0 I Output clock select input terminal
47 CKSEL1 I Output clock select input terminal
48 XMODE I Reset input terminal
For latch-up countermeasure, set digital (DVDD) and analog (AVDD) power on/off in the same timing.
Pin Name FunctionI/O
9
AK4527BVQ (IC813)
L0OP1
L0OP0/SDA/CDTI
444342
DIF1/SCL/CCLK
DIF0/CSN
P/S
MCLK
39
38
40
41
DZF1
37
AVSS
36
AVDD
35
VCOM
VREFH
34
AVR-1602/682
22
CAD1
CAD0
33
DZ F2/OVF
32
RIN+
31
RIN–
30
LIN+
29
LIN–
28
ROUT1
27
LOUT1
26
ROUT2
25
LOUT2
24
ROUT3
23
LOUT3
SDOS
I2C
SMUTE
BICK
LRCK
SDTI1
SDTI2
SDTI3
SDTO
DAUX
DFS
1
2
3
4
5
6
7
8
9
10
11
12
13 14
NC
AK4527BVQ
15
TVDD
DZ FE
Top View
16 17 18
PDN
DVSS
DVDD
192021
NC
TST
ADIF
AK4527BVQ Terminal Function
Pin
Pin Name I/O Function
No.
1 SDOS I SDTO source select pin, L: Internal ADC output, H: DAUX input
2 I2C I Serial control mode select pin, L: 3-core serial, H: I2C bus
3 SMUTE I Soft mute pin, H: Soft mute start, L: Release
4 BICK I Audio serial data clock pin
5 LRCK I Input channel clock pin
6 SDTI1 I DAC1 audio serial data input pin
7 SDTI2 I DAC2 audio serial data input pin
8 SDTI3 I DAC3 audio serial data input pin
9 SDTO O Audio serial data output pin
10 DAUX I Auxiliary audio serial data input pin
11 DFS I Double speed sampling mode pin, L: Normal, H: Double
12 NC No Connect, No internal bonding
13 DZFE I Zero input detect enable pin
14 TVDD Power pin for output buffer, 2.7V~5.5V
15 DVDD Digital power pin, 4.5V~5.5V
16 DVss Digital GND pin, 0V
17 PDN I Power down & reset pin, L: Powered-down and register initialized, Reset with PDN when switching P/S or CAD0-1
18 TST I Test pin, connected to DVSS
19 NC No Connect, No internal bonding
20 ADIF I Analog Input Format Select pin
21 CAD1 I Chip address-1 pin
22 CAD0 I Chip address-0 pin
23 LOUT3 O DAC3L channel analog out pin
24 ROUT3 O DAC3R channel analog out pin
25 LOUT2 O DAC2L channel analog out pin
26 ROUT2 O DAC2R channel analog out pin
27 LOUT1 O DAC1L channel analog out pin
28 ROUT1 O DAC1R channel analog out pin
29 LIN- I L-ch analog inverted input pin
30 LIN+ I L-ch analog non-inverted input pin
31 RIN- I R-ch analog inverted input pin
32 RIN+ I R-ch analog non-inverted input pin
33 DZF2/OVF O 0 input detect 2 pin/Analog input overflow detect pin
34 VCOM O Common V-out pin, AVDD/2, connect large capacitor to avoid noise
35 VREFH I Ref. V input pin, AVDD
36 AVDD Analog GND pin, 4.5V~5.5V
37 AVss Analog GND pin, 0V
38 DZF1 O 0 input detect pin, H: Input data of G1 is 8192 times “0” in a raw or RSTN bit “0”
39 MCLK I Master clock input pin
40 P/S I Parallel/Serial select pin, L: Serial control
DIF0 I Audio data I/F format 0 pin (parallel control)
41
CSN I Chip select pin (3-wire serial control), connect to DVDD when I
DIFI I Audio data I/F format 1 pin (parallel control)
42
SCL/CCLK I Control data clock pin (serial control), I
LOOP0 I Loop back mode 0 pin (parallel control), effects digital loop back ADC to all DAC
43
SDA/CDTI I/O Control data input pin (serial control), I
2
C=”L”: CCLK (3-wire serial), I2C=”H”: SCL (I2C bus)
2
C=”L”: CCTI (3-wire serial), I2C =”H” SDA (I2C bus)
44 LOOP1 I Loop back mode 1 pin, from SDT1 to all DAC
2
C bus control
10
AVR-1602/682
1
2
3
4
5
6
7
8
18
17
16
15
14
13
12
11
Q3
VDD
OE
Q7
Q8
Q11
Q10
Q9
Q6
VSS
DATA
CLOCK
LCK
Q0
Q1
Q2
9
10
Q4
Q5
CONTROL CIRCUIT
12-bit SHIFT RESISTER
12-bit STRAGE RESISTER
OUTPUT BUFFER (OPEN DRAIN)
BU2090F (IC302)
1
MM74LCX244 (IC818,819)
RC1117S25T (IC820)
RC1117S33ST (IC811)
2
3
2
ADJ/GND
OUT
IN
MM74HC151 (IC832)
V
OUT
FRONT VIEW
LA1266 (IC402)
10
4
1
3
8
19
15
17
18
14
21
22
GND
Vcc
5
11
IF
BUFFER
IF
BUFFER
2
F M - IF
6
Q.D.
7
REG
23
OSC
OSC
BUFFER
24
NARROW
S-M ETER
S-M ETER
16
LED
DRIVER
RF MIX
12
20
AM -IF DET
AGC
POST
AM P
9
13
AM -IF FM-IF FM -IN
AM-IN
20
19
18
17
16
15
14
13
12
9
8
7
5
6
1
21
LA3401 (IC403)
22
VOL
REG
OSC
SYMM ETRICAL
REOCTANCE
CIRCUIT
PHASE
COM PARATO R
VCO STOP
PILOT DET
FF
FF
FF
38kHz
FF
38kHz 90°FF19kHz 90°
MUTING
FM AM CHANGE
Ro
Rc
Rc
Rb
2
3
4
DECODER
M UTIN G CO NTR O L
FM AM CHANGE O VER
Vcc ON
MUTING
MUTING
OUTPUT
STEREO
SW ITCH
TRIG G ER
LAM P
DRIVER
Rb
10
11
LC72131 (IC401)
1
20
2
19
3
18
417
5
16
6
15
7
14
8
13
9 12
10 11
XIN
CE
DI
CL
DO
BO1
BO2
BO3
BO4
IO 1
AOU T
AIN
PD
VDD
FM IN
AM IN
IO 2
IF IN
Vss
XOU T
TDA7330BD (IC202)
TOP VIEW
POR
MUXIN
TM
V
REF
FSEL
COMP
T2
FILOUT
V
CC
GND
ARI
T1
QUAL
T3
RDDA
T4
RDCL
OSCOUT
T57
OSCIN
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
124
12 13
1
2
3
4
5
6
7
8
20
19
18
16
15
14
13
I3
VCC
OE2
O2
I5
O0
I4
O1
I6
OE
I0
O4
I1
O5
I2
O6
912
O7
O3
10
11
GND
I7
TOP VIEW
D4
D5
D6
D7
A
B
D2
D1
D0
Y
W
S
D3
C
4
5
6
7
A
B
C
Vcc
15
14
13
12
11
10
9
16
2
3
4
5
6
7
8
1
2
1
0
Y
W
ST ROBE
GND
3
DATA
INPUTS
OUTPUTS
DATA
INPUTS
DATA
SELECT
TOP VIEW
17
11
AVR-1602/682
LC75721E (IC301)
G7 G8G9
G10
G11
AA8/G12
AA7/G13
48 33
49
DI
CL
CE
RES
V
DD
OSCI
OSCO
Vss
TEST
V
FL
G1
G2
G3
G4
G5
G6
64
AM 1
AM 2
AM 3
AM 4
AM 5
AM 6
AM 7
TC9273N-007(IC701)
1
Vss
2
S1
S2
3
4
S3
S4
5
6
S5
7
S6
8
S7
9
S8
10
S9
11
S10
12
13
GND
14
CK
V
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
STB
DAT A
AA6/G14
AA5/G15
AA4/G16
AM 8
AM 9
DD
KIC9164AN (IC221)
LC75721E Terminal Function
AA3
AA2
AA1
AM35
AM34
AM33
32
AM 17
AM 18
AM 19
AM 20
AM 21
AM 22
AM 23
AM 24
AM 25
AM 26
AM 27
AM 28
AM 29
AM 30
AM 31
AM 32
17
161
AM 10
AM 11
AM 12
AM 13
AM 14
AM 15
AM 16
28
27
26
25
24
23
22
21
20
19
18
17
16
15
TC9273N Terminal Function
Pin No.
12~27
Symbol Function
1
Vss
13
GND
V
28
DD
2~12
S1~S10
14
CK
15
DATA
STB
16
Symbol
DD
V
V
SS
V
FL
DI
CL
CE
OSCI
OSCO
RES
AM1~AM35
AA1~AA3
AA4/G16
AA5/G15
AA6/G14
AA7/G13
AA8/G12
G1~G11
TEST
Power terminal +5V
Power terminal GND
Power terminal FL drive
Serial data transfer terminal
DI: Data
CL: Clock
CE: Chip enable
External CR connecting terminal
System reset terminal
Anode output terminal
Anode/Grid output terminal
Grid output terminal
LSI test terminal
Name
+ Power Terminal
Digital Ground
+ Power Terminal
I/O Terminal
Clock Input
Data Input
Strobe Input
Function
L-S1
L-S2
L-S3
L-S4
L-C O M 1
L-S5
L-S6
L-C O M 2
L-S7
L-S8
L-C O M 3
GND
Dual Power Use:V
Input terminal of analog switch.
Clock input for data transfer.
Serial input for switch setting.
Strobe InputStrobe input for data writing.
DD
=8.0~17V
GND=0V
Vss=- 8.0~- 17V
Single Power Use:VDD=8.0~18V
SS
V
1
2
3
4
5
6
7
8
9
10
11
12
13
ST
14 15
GND=0V
28
27
26
25
24
23
22
21
20
19
18
17
16
DD
V
R-S1
R-S2
R-S3
R-S4
R-COM 1
R-S5
R-S6
R-COM 2
R-S7
R-S8
R-COM 3
DATA
CK
Low level
Border Input
Terminal
W27W201 (IC807)
Vpp
A16
A15
A12
GND
1
2
3
4
5
A7
6
A6
7
A5
8
A4
9
A3
10
A2
A1
11
A0
12
13
0
O
14
1
O
15
O
2
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
SN74LV00APW (IC822)
1
GND
1A
1B
2
1Y
3
2A
4
2B
5
6
2Y
7
14
13
12
11
10
9
8
Vcc
P
A17
A14
A13
A8
A9
A11
G
A10
E
O
O
O
O
O
Vcc
4B
4A
4Y
3B
3A
3Y
NJM2068DD
CCVPP
V
18
8
A0-A17
P
E
7
6
5
4
3
G
V
SS
74HCU04 (IC803)
1
1A
1Y
2A
2Y
3A
3Y
GN D
2
3
4
5
6
7
14
Vcc
13
6A
6Y
12
11
5A
5Y
10
4A
9
8
4Y
(IC241,251,261,271,281,291,702,703)
BA4510F (IC805~806)
NJM2068MD (IC814~816)
0-O7
O
A OUTPUT
A –INPUT
A+INPUT
1
2
3
V
4
LA7952 (IC601,651,652)
6dB
am p
45
GND
VIN1
video sw itch
(4 in o u t 1 o u tp u t)
7
6
Vcc
VIN2
driver
1
VIDEO OUT
23
A
B
control
V
8
B OUTPUT
7
6
B –INPUT
B +INPUT
5
8
9
VIN3
VIN4
12
AVR-1602/682
SN74LV4040 (IC831)
T FF1
R
16
CC
V
Q10
15
14
Q9
Q7
13
Q8
12
11
MR
10
CP
Q0
9
Q
T FF2
Q
D
R
Q0
Q11
Q5
Q4
Q6
Q3
Q2
Q1
GND
1
2
3
4
5
6
7
8
CP
MR
KIA7805AP (IC104)
KIA7815AP (IC101)
NJM7805FA (IC103,829)
NJM7812FA (IC602)
FRONT
VIEW
Terminal Function
IN P U T S O U T P U T S
MR
CP
L
L
H
X
H = H IG H v o lta g e le v e l
L=LO W voltage level
X=don't care
= L O W -to -H IG H c lo c k tra n s itio n
= H IG H -to-L O W clo ck tra nsition
Q
Q
D
Q1
T FF12
R
D
Q
Q
Q11
NJM7915FA (IC102)
FRONT
VIEW
M62446FP (IC231)
1
OUT4
2
Cin
Rin
Lin
OUTPUT
PORT
3
4
DD
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
volume
volume
volume
volume
volume
volume
tone tone
MCU
I/F
Qn
no change
count
L
OUT3
OUT2
OUT1
AV
SWin
GNDS
SRin
SLin
GNDC
DNDR
GNDL
BYPASSR
BLPASSL
LTRE
LBASS3
LBASS2
LBASS1
MM74LCX574 (IC808,809) MM74HCT244 (IC828,830)
1G
1A
2Y
1A
2Y
1A
2Y
1A
2Y
GND
0
0
1
1
2
2
3
3
GND
OE
D
D
D
D
D
D
D
D
20 1
V
CC
0
1
2
3
4
5
6
7
0
Q
19 2
1
18 3
Q
2
17 4
Q
3
16 5
Q
4
Q
15 6
5
14 7
Q
6
13 8
Q
7
12 9
Q
11 10
CP
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
DD
DV
CLK
DATA
LATCH
DGND
AGND
SW
OUT
SR
OUT
SL
OUT
C
OUT
R
OUT
L
SS
AV
CL1
CL2
CR1
CR2
RTRE
RBASS3
RBASS2
RBASS1
20 1
19 2
18 3
1Y
17 4
16 5
1Y
15 6
14 7
1Y
13 8
12 9
1Y
11 10
OUT
V
2G
2A
2A
2A
2A
CC
0
0
1
1
2
2
3
3
Input
GND
Output
OPTICAL
INPUT
Vcc
Vout
GND
IR SENSOR
NJL64H380A(RMC301)
TOP VIEW
Vcc
Vout
GND
Input
GND
Output
OUTPUT
GP1FA502TZ(IC817)
V
CC
V
OUT
GND
Vin
Vcc
Head Amp Amp Limitter Comparator
PD
ABLC
B.P.F
GND
Detector
LED
DRIVE
IC
22kohm
CC
V
V
OUT
GND
V
CC
Vin
GND
IC PROTECTOR
ICP-N15 (IC105)GP1FA502RZ (IC802)
FRONT VIEW
POSISTOR
P43T7D330BW16
FRONT VIEW
13
2SC1740S
2SC3199Y
KSA916Y
KSA992F
KSC1845F
KTA1266Y
KTA1268BL
KTC2874B
KTC3198Y
KTC3200BL
2SC2412K
KTC3880S
DTA114EK
DTA114YK
DTA144EK
DTC114EK
DTC114YK
DTC144EK
TOP
VIEW
E
B
C
TOP
VIEW
E
B
C
FRONT
VIEW
B
C
E
TOP VIEW
KDS160MTZJ3.3B
MTZJ5.1B
MTZJ5.6B
MTZJ6.8B
MTZJ7.5A
MTZJ7.5B
MTZJ11B
MTZJ18B
MTZJ20B
1N4007
1SS133
B
C
E
R1
R2
B
C
E
R1
R2
2SK117
FRONT
VIEW
S
G
D
DTA114ES
DTC114TS
DTC114YS
DTC144ES
FRONT
VIEW
B
C
E
DTA Series
DTC Series
DTA114EK
DTA114YK
R1
10kohm /WR210kohm /W
DTA144EK
47kohm /W 47kohm /W
10kohm /W
47kohm /W
DTA114ES
10kohm /W 10kohm /W
DTC114EK
DTC114YK
10kohm /W 10kohm /W
DTC144EK
R1
R2
47kohm /W 47kohm /W
10kohm /W 47kohm /W
DTC144ES
47kohm /W 47kohm /W
DTC114YS
10kohm /W 47kohm /W
DTC114TS
10kohm /W¾
HL-50RDRF4T
TRANSISTORS
DIODES (LED included)
TOP VIEW
KBPC604
TOP VIEW
AVR-1602/682
14
FL DISPLAY
16-st-42GNK (FL301)
AVR-1602/682
1
TUNED
STEREO
RDS
CH
G16
TUNED
RDS
CH
G15 G13
STEREO
AUTO
Pin Assignment
AUTO
G14
MULTI
REC
MULTI
REC
PHONO
VCR
G12
PHONO
VCR
G11
CD
-
1
G10
CD
-
TUNER
-2-
TUNER
-2-
1
AUXMDDVD /
3 V.AUX
G9
3
G8
G7
AUX
V.AUX
VDP TV
TAPE
/
G6
DVD /
MD
G5
/
-1-
G4
VDP
TAPE
/
2
DBS
DIGITAL
G3
TV
-
PRO LOGIC
DIGITAL
ANALOG
G2
DBS
/
1-2
DIGITAL
58
F2F1
G1
PRO LOGIC
DIGITAL
ANALOG
S38
S1
S6
S11
S16
S21
S26
S31
S14
S13
S9
S10
S15
S11
S12
G2~G16
S2
S3
S8
S7
S12
S13
S17
S18
S22
S23
S27
S28
S32
S33
G1
S9
S14
S19
S24
S29
S34
S1
S6
S2
S7
S5
S3
S4
S4
S5
S10
S15
S20
S25
S30
S35
PIN NO.
CONNECTION
PIN NO.
CONNECTION
PIN NO.
CONNECTION
12345
F1 F1 S1 S2 S3
21 22
23 24 25
S19 S20 S21 S22 S23 S24 S25 S26 S27 S28 S29 S30 S31 S32 S33 S34 S35 S36 S37 S38
41 42 43 44 45
G16 G15 G14 G13 G12 G11 G10 G9 G8 G7 G6 G5 G4 G3 G2 G1 F2 F2
Anode & Grid Assignment
G1
G2~G16
S1
S2
S3
S4
S5
S6
S7
S8
S9
TV
/
- 1
VDP
TAPE
S36
S37
S38
S1
S2
S3
S4
S5
S6
S7
S1
S2
S3
S4
S5
S6
S7
S8
S9
S9
G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G11 G12 G13 G14 G15
- 2
S38
DBS
S10
S11
S12
S13
S14
S15
S16
S17
S18
/(DVD)
/(MD)
78910111213141516171819
6
S5 S6 S7 S8 S9 S10 S11 S12 S13 S14 S15
S4
27 28 29 30 31 32 33 34
26
47 48 49 50 51 52 53 54 55 56 57
46
G2~G16
G1
S10
S11
S12
S13
S14
S15
DIGITAL
PRO LOGIC
AUXDVD
MD
V.AUX
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
S24
S25
S26
S27
TUNER
- 2
CD
-
G1
G2~G16
S19
S20
S21
S22
S23
S24
S25
S26
S27
PHONO
1
VCR
MULTI
- 3
S16 S17
35 36 37 38 39 40
58
F1, F2 : Filament
G1~G16 : Grid
S1~S38 : Anode
G1
G2~G16
S28
S29
S30
S31
S32
S33
S34
S35
S28
S29
S30
S31
S32
S33
S34
S35
G16
REC
STEREO
AUTO
TUNED
RDS
CH
20
S18
15
PRINTED WIRING BOARDS
1
MAIN P.W.B. UNIT Ass'y
2
AVR-1602/682
3
4
5
76
8
1
3
1
8
1 5 1 9 1 5 1 5 1
1
3
1
3
1
3
6
1
3
A
B
13
1
3
1
4
1
8
FRONT CNT P.W.B.
C
1
11
1
D
12
16
E
MAIN P.W.B.
INPUT P.W.B.
COMPONENT SIDE
16
AVR-1602/682
1
2
3
4
5
76
8
A
B
FRONT CNT P.W.B.
C
D
E
INPUT P.W.B.
MAIN P.W.B.
FOIL SIDE
17
AVR-1602/682
1
CPU P.W.B. UNIT Ass'y
2
1 8
3
4
1 4
5
1 8
76
8
A
42
121
CPU P.W.B
1 1
1015
22
B
112
111
AC OUTLET P.W.B
11711718
(E2 ONLY)
C
111
2
13
1 8
16 9
1
16
15
FRONT P.W.B
D
E
16
COMPONENT SIDE
18
AVR-1602/682
1
AC OUTLET P.W.B
(E2 ONLY)
2
CPU P.W.B
3
4
5
76
8
A
B
110
FRONT P.W.B
2011
C
D
FOIL SIDE
E
19
AVR-1602/682
1
CONNECTION P.W.B. UNIT Ass'y
TUNER P.W.B.
2
3
4
5
76
S-VIDEO P.W.B.
8
A
VIDEO P.W.B.
TACT S/W P.W.B.
B
H/P P.W.B.
C
D
CONNECTION P.W.B.
E
COMPONENT SIDE
20
AVR-1602/682
1
2
S-VIDEO P.W.B.
3
4
5
76
8
A
VIDEO P.W.B.
TACT S/W P.W.B.
TUNER P.W.B.
B
H/P P.W.B.
C
D
CONNECTION P.W.B.
E
FOIL SIDE
21
AVR-1602/682
1
PRE AMP P.W.B. UNIT Ass'y
2
3
4
5
76
8
A
1
8
B
1 5 1 9 1 5 1 5 1 6
COMPONENT SIDE
C
D
FOIL SIDE
E
22
AVR-1602/682
1
DSP P.W.B. UNIT Ass'y
2
3
1
4
4
8
5
5
5
4
5
8
1
8
5
4
8
1
4
1
8
1
4
1
10
20
11
5
8
9
1
14
1 7
20
11110
11
20
1
8
10
25
36
1
16
1
7
9
13
24
12
1
37
48
14
8
16
1
10
76
8
8
A
20
11
B
14
1
15 28
1
1
1
17
17
10
COMPONENT SIDE
C
10
11
1
20
D
10
11
1
20
FOIL SIDE
E
23
AVR-1602/682
1
VOLTAGE SEL P.W.B. UNIT Ass'y
32
4
A
B
COMPONENT SIDE
C
D
E
24
NOTE FOR PARTS LIST
l Part indicated with the mark "" are not always in stock and possibly to take a long period of time for supplying, or in
some case supplying of part may be refused.
l When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying.
l Ordering part without stating its part number can not be supplied.
l Part indicated with the mark " " is not illustrated in the exploded view.
l Not including Carbon Film ±5%, 1/4W Type in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
WARNING:
Parts marked with this symbol
Use ONLY replacement parts recommended by the manufacturer.
have critical characteristics.
AVR-1602/682
ll
l Resistors
ll
Ex.: RN 14K 2E 182 G FR
Type Shape Power Resist- Allowable Others
and per- ance error
formance
t
RD : Carbon 2B : 1/8W F : ±1% P : Pulse-resistant type
RC : Composition 2E : 1/4W G : ±2% NL : Low noise type
RS : Metal oxide film 2H : 1/2W J : ±5% NB : Non-burning type
RW : Winding 3A : 1W K : ±10% FR : Fuse-resistor
RN : Metal film 3D : 2W M : ±20% F : Lead wire forming
RK : Metal mixture 3F : 3W
t
3H : 5W
Resistance
1 8 2 ⇒ 1800 ohm = 1.8 kohm
s
s
• Units: ohm
1 R 2 ⇒ 1.2 ohm
s
s
• Units: ohm
Indicates number of zeros after effective number.
2-digit effective number.
1-digit effective number.
2-digit effective number, decimal point indicated by R.
t
t
ll
l Capacitors
ll
Ex.: CE 04W 1H 2R2 M BP
Type Shape Dielectric Capacity Allowable Others
and per- strength error
formance
t
CE : Aluminum foil 0J : 6.3V F : ±1% HS : High stability type
electrolytic
CA : Aluminum solid 1A : 10V G : ±2% BP : Non-polar type
electrolytic
CS : Tantalum electrolytic 1C : 16V J : ±5% HR: Ripple-resistant type
CQ : Film 1E : 25V K : ±10% DL : For change and discharge
CK : Ceramic 1V : 35V M : ±20% HF : For assuring high
CC : Ceramic 1H : 50V Z : +80% U : UL par t
CP : Oil 2A : 100V –20% C : CSA part
CM : Mica 2B : 125V P : +100% W : UL-CSA type
CF : Metallized 2C : 160V –0% F : Lead wire forming
CH : Metallized 2D : 200V C : ±0.25pF
t
2E : 250V D : ±0.5pF
2H : 500V = : Others
2J : 630V
t
Capacity (electrolyte only)
2 2 2 ⇒ 2200µF
s
s
• Units: µF.
2 R 2 ⇒ 2.2µF
s
s
• Units: µF.
Indicates number of zeros after effective number.
2-digit effective number.
1-digit effective number.
2-digit effective number, decimal point indicated by R.
Capacity (except electrolyte)
2 2 2 ⇒ 2200pF=0.0022µF
s
s
(More than 2) Indicates number of zeros after effective number.
• Units: pF.
2 2 1 ⇒ 220pF
s
s
(0 or 1) Indicates number of zeros after effective number.
• Units: pF.
• When the dielectric strength is indicated in AC, "AC" is included after the dieelectric
strength value.
2-digit effective number.
2-digit effective number.
t
requency
25
Loading...