Trademarks used in this text: Dell™, the DELL logo, Dell Precision™, Precision ON™,ExpressCharge™, Latitude™,
Latitude ON™, OptiPlex™, Venue™, Vostro™, and Wi-Fi Catcher™ are trademarks of Dell Inc. Intel®, Pentium®, Xeon®,
Core™, Atom™, Centrino®, and Celeron® are registered trademarks or trademarks of Intel Corporation in the U.S. and
other countries. AMD® is a registered trademark and AMD Opteron™, AMD Phenom™, AMD Sempron™,
AMD Athlon™, ATI Radeon™, and ATI FirePro™ are trademarks of Advanced Micro Devices, Inc. Microsoft®,
Windows®, MS-DOS®, Windows Vista®, the Windows Vista start button, and Office Outlook® are either trademarks or
registered trademarks of Microsoft Corporation in the United States and/or other countries. Blu-ray Disc™ is a
trademark owned by the Blu-ray Disc Association (BDA) and licensed for use on discs and players. The Bluetooth
word mark is a registered trademark and owned by the Bluetooth® SIG, Inc. and any use of such mark by Dell Inc. is
under license. Wi-Fi® is a registered trademark of Wireless Ethernet Compatibility Alliance, Inc.
2013 - 10
Rev. A00
®
Contents
1 Working on Your Computer.................................................................................5
Before Working Inside Your Computer.............................................................................................5
Turning Off Your Computer..............................................................................................................6
After Working Inside Your Computer............................................................................................... 6
2 Removing and Installing Components..............................................................9
Use the following safety guidelines to help protect your computer from potential damage and to help to
ensure your personal safety. Unless otherwise noted, each procedure included in this document
assumes that the following conditions exist:
•You have read the safety information that shipped with your computer.
•A component can be replaced or--if purchased separately--installed by performing the removal
procedure in reverse order.
WARNING: Before working inside your computer, read the safety information that shipped with
your computer. For additional safety best practices information, see the Regulatory Compliance
Homepage at
CAUTION: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is not
authorized by Dell is not covered by your warranty. Read and follow the safety instructions that
came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or
by periodically touching an unpainted metal surface, such as a connector on the back of the
computer.
www.dell.com/regulatory_compliance
CAUTION: Handle components and cards with care. Do not touch the components or contacts on
a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a
processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable
itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,
press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep
them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,
ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear differently than shown in
this document.
To avoid damaging your computer, perform the following steps before you begin working inside the
computer.
1.Ensure that your work surface is flat and clean to prevent the computer cover from being
scratched.
2.Turn off your computer (see Turning Off Your Computer).
CAUTION: To disconnect a network cable, first unplug the cable from your computer and
then unplug the cable from the network device.
5
3.Disconnect all network cables from the computer.
4.Disconnect your computer and all attached devices from their electrical outlets.
5.Press and hold the power button while the computer is unplugged to ground the system board.
6.Remove the cover.
CAUTION: Before touching anything inside your computer, ground yourself by touching an
unpainted metal surface, such as the metal at the back of the computer. While you work,
periodically touch an unpainted metal surface to dissipate static electricity, which could harm
internal components.
Turning Off Your Computer
CAUTION: To avoid losing data, save and close all open files and exit all open programs before you
turn off your computer.
1.Shut down the operating system:
– In Windows 8:
*Using a touch-enabled device:
a.Swipe in from the right edge of the screen, opening the Charms menu and select
Settings.
b.Select the and then select Shut down
*Using a mouse:
a.Point to upper-right corner of the screen and click Settings.
b.Click the and select Shut down.
– In Windows 7:
1.Click Start.
2.Click Shut Down.
or
1.Click Start.
2.Click the arrow in the lower-right corner of the Start menu as shown below, and then click
Shut Down..
2.Ensure that the computer and all attached devices are turned off. If your computer and attached
devices did not automatically turn off when you shut down your operating system, press and hold
the power button for about 6 seconds to turn them off.
After Working Inside Your Computer
After you complete any replacement procedure, ensure you connect any external devices, cards, and
cables before turning on your computer.
1.Replace the cover.
6
CAUTION: To connect a network cable, first plug the cable into the network device and then
plug it into the computer.
2.Connect any telephone or network cables to your computer.
3.Connect your computer and all attached devices to their electrical outlets.
4.Turn on your computer.
5.If required, verify that the computer works correctly by running the Dell Diagnostics.
7
8
Removing and Installing Components
This section provides detailed information on how to remove or install the components from your
computer.
Recommended Tools
The procedures in this document may require the following tools:
•Small flat-blade screwdriver
•Phillips screwdriver
•Small plastic scribe
System Overview
The figure below displays the inside view of the Small Form Factor after the base cover has been
removed. The call outs show the names and the layout of the components inside the computer.
Inside view
2
1.optical drive
2.front bezel
3.power supply unit
4.expansion card
9
5.intrusion switch
6.heatsink cover
7.heatsink
8.drive cage
1.front I/O
2.system fan
3.system board
4.memory module
5.coin cell
6.speaker
Removing the Cover
1.Follow the procedures in
2.Remove the thumbscrews that secure the cover to the computer. Slide the cover from the
computer.
Before Working Inside Your Computer
.
10
3.Lift the cover upward to a 45–degree angle and remove it from the computer.
Installing the Cover
1.Place the cover on the computer.
2.Slide the computer cover towards the front of the chassis until it is fully engaged.
3.Tighten the thumbscrew in clockwise direction to secure the computer cover.
4.Follow the procedures in
After Working Inside Your Computer
.
11
Removing the Front Bezel
1.Follow the procedures in
2.Remove the cover.
3.Pry the front bezel retention clips away from the chassis.
4.Rotate the bezel away from the computer to release the hooks on the opposite edge of the bezel
from the chassis. Then, lift the chassis and remove the front bezel from the computer.
Before Working Inside Your Computer
.
Installing the Front Bezel
1.Insert the hooks along the bottom edge of the front bezel into the slots on the chassis front.
2.Push the bezel toward the computer to engage the front bezel retention clips until they click into
place.
3.Install the cover.
4.Follow the procedures in
After Working Inside Your Computer
.
Removing The Expansion Card
1.Follow the procedures in
2.Remove the cover
3.Rotate the release tab on the card-retention latch upward.
Before Working Inside Your Computer
.
12
4.Perform the following steps as shown in the illustration:
a) Pull the release lever away from the expansion card until you release the securing tab from the
dent in the card. [1].
b) Ease the card up and out of its connector and remove it from the computer. [2].
13
Installing The Expansion Card
1.Insert the expansion card into the connector on the system board and press down to secure it in
place.
2.Install the cover
3.Follow the procedures in
After Working Inside Your Computer
.
Removing the Optical Drive
1.Follow the procedures in
2.Remove the cover.
3.Disconnect the data and power cables from the back of the optical drive.
4.Lift the tab and slide the optical drive out to remove it from the computer.
14
Before Working Inside Your Computer
.
5.Flex the optical-drive bracket and then lift the optical drive from the bracket
6.Repeat steps 3 to 5 to remove the second optical drive (if available).
Installing the Optical Drive
1.Insert the optical drive into the bracket.
2.Slide the optical drive to insert it into the drive cage.
3.Connect the data and power cables to the optical drive.
4.Install the cover.
5.Follow the procedures in
After Working Inside Your Computer
.
Removing the Drive Cage
1.Follow the procedures in
2.Remove the:
a) cover
b) front bezel
c) optical drive
3.Disconnect the data and the power cables from the back of the hard drive.
Before Working Inside Your Computer
.
15
4.Slide the blue drive-cage handle toward unlock position and lift the hard drive cage from the
computer.
Installing the Drive Cage
1.Place the drive cage on the edge of the computer to allow access to the cable connectors on the
hard drive.
2.Connect the data and power cables to the back of the hard drive.
3.Flip over the drive cage and insert it into the chassis. The drive cage tabs are secured by the slots in
the chassis.
4.Slide the drive-cage handle toward the locked position.
5.Install the:
a) front bezel
b) optical drive
c) cover
16
6.Follow the procedures in
After Working Inside Your Computer
Removing the Hard Drive
.
1.Follow the procedures in
2.Remove the:
a) cover
b) optical drive
c) drive cage
3.Perform the following steps as shown in the illustration: and
a) Press the retention clips inwards [1].
b) Slide the hard-drive bracket out from the drive cage. [2].
4.Flex the hard-drive bracket and remove the hard drive from the bracket.
Before Working Inside Your Computer
.
5.Remove the screws that secure the mini hard drive to the hard-drive bracket and remove the hard
drive from its bracket.
NOTE: Perform step 5 only if you have a mini hard drive.
17
Installing the Hard Drive
1.Tighten the screws to secure the mini hard drive (if available) to the hard-drive bracket.
2.Flex the hard-drive bracket and then insert the hard drive into the bracket.
3.Slide the hard-drive bracket into the drive cage.
4.Install the:
a) drive cage
b) optical drive
c) cover
5.Follow the procedures in
After Working Inside Your Computer
Removing the Speaker
1.Follow the procedures in
2.Remove:
a) cover
b) optical drive
c) drive cage
3.Perform the following steps as shown in the illustration:
a) Disconnect the speaker cable from the system board [1]
b) Release it from the securing tab inside the chassis. [2].
Before Working Inside Your Computer
.
.
4.Perform the following steps as shown in the illustration:
a) Press the speaker-securing tab [1].
b) Slide the speaker towards the right of the computer to release it [2].
18
Installing the Speaker
1.Place the speaker at the appropriate location on the chassis.
2.Press the speaker-securing tab and slide the speaker towards the left of the computer to secure it.
3.Guide the speaker cable through the securing tab and connect the speaker cable to the system
board.
4.Install the:
a) drive cage
b) optical drive
c) cover
5.Follow the procedures in
After Working Inside Your Computer
.
Memory Module Guidelines
To ensure optimal performance of your computer, observe the following general guidelines when
configuring your system memory:
•Memory modules of different sizes can be mixed (for example, 2 GB and 4 GB). But, all populated
channels must have identical configurations.
•Memory modules must be installed beginning with the first socket.
NOTE: The memory sockets in your computer may be labeled differently depending on the
hardware configuration. For example, A1, A2 or 1,2,3.
•If the quad-rank memory modules are mixed with single or dual-rank modules, the quad-rank
modules must be installed in the sockets with the white release levers.
•If memory modules with different speeds are installed, they operate at the speed of the slowest
installed memory modules.
19
Removing the Memory
1.Follow the procedures in
2.Remove the cover.
3.Press down on the memory retaining tabs on each side of the memory modules, and lift the
memory modules out of the connectors on the system board.
Before Working Inside Your Computer
.
Installing the Memory
1.Align the notch on the memory-card with the tab in the system-board connector.
2.Press down on the memory module until the release tabs spring back to secure them in place.
3.Install the cover.
4.Follow the procedures in
After Working Inside Your Computer
.
Removing the System Fan
1.Follow the procedures in
2.Remove
a) cover
b) optical drive
c) drive cage
d) front bezel
3.Perform the following steps as shown in the illustration:
a) Press the system-fan cable [1].
b) Disconnect the system-fan cable from the system board [2].
c) Unroute the cable from the system board.
d) Pry and remove the system fan away from the grommets securing it to the front of the
computer.
e) Then press the grommets inward along the slots and pass through the chassis.
20
Before Working Inside Your Computer
.
Installing the System Fan
1.Place the system-fan in the chassis.
2.Pass the grommets through the chassis and slide outward along the groove to secure it in place.
3.Connect the system-fan cable to the system board.
4.Install:
a) front bezel
b) drive cage
c) optical drive
d) cover
5.Follow the procedures in
After Working Inside Your Computer
.
Removing the Power Switch
1.Follow the procedures in
2.Remove the:
a) cover
b) front bezel
c) optical drive
d) drive cage
3.Perform the following steps as shown in the illustration:
a) Disconnect the power-switch cable from the system board.
b) Unroute the cable from the system board.
Before Working Inside Your Computer
.
21
4.Perform the following steps as shown in the illustration:
a) Press the clips on both side of the power switch [1].
b) Release it from the chassis [2].
c) Remove the power switch along with its cable from the computer
Installing the Power Switch
1.Slide the power switch in through the front of the computer.
2.Connect the power-switch cable to the system board.
3.Install the:
a) drive cage
b) optical drive
22
c) front bezel
d) cover
4.Follow the procedures in
After Working Inside Your Computer
Removing the I/O Panel
.
1.Follow the procedures in
2.Remove the:
a) cover
b) optical drive
c) drive cage
d) front bezel
3.Perform the following steps as shown in the illustration:
a) Disconnect the I/O cable the computer [1].
b) Disconnect the audio cable the computer [2].
c) Disconnect the HDD LED cable the computer [3].
Before Working Inside Your Computer
.
4.Perform the following steps as shown in the illustration:
a) Remove the screw that secures the I/O panel to the chassis. [1].
b) Slide the I/O panel to release and remove it from the computer [2].
23
Installing the I/O Panel
1.Insert the I/O panel into the slot on the chassis front.
2.Slide the I/O panel to secure it to the chassis.
3.Tighten the screw to secure the I/O panel to the chassis.
4.Connect the I/O panel, audio cable, and fan shelter clip to the system board.
5.Install the:
a) drive cage
b) optical drive
c) front bezel
d) cover
6.Follow the procedures in
After Working Inside Your Computer
.
Removing the Power Supply
1.Follow the procedures in
2.Remove:
a) cover
b) front bezel
c) optical drive
d) drive cage
3.Perform the following steps as shown in the illustration:
a) Press the 8–pin and 4–pin power cable [1].
b) Disconnect the 8-pin and 4–pin power cables from the system board [2].
c) Unroute the cable from the system board.
24
Before Working Inside Your Computer
.
4.Release the blue latch from the system.
5.Remove the screws that secure the power supply to the back of the computer
25
6.Perform the following steps as shown in the illustration:
a) Press the latch downwards to release the power supply unit [1].
b) Slide the power supply unit from the computer [2].
7.Lift the power supply out of the computer.
26
Installing the Power Supply
1.Place the power supply in the chassis and slide towards the back of the computer to secure it.
2.Tighten the screws securing the power supply to the back of the computer.
3.Connect the 4-pin and 8–pin power cables to the system board.
4.Thread the power cables into the chassis clips.
5.Install:
a) drive cage
b) optical drive
c) front bezel
d) cover
6.Follow the procedures in
After Working Inside Your Computer
.
Removing the Coin-Cell Battery
1.Follow the procedures in
2.Remove the:
a) cover
b) front bezel
c) drive cage
3.Press the release latch away from the battery to allow it to pop-up from the socket and then lift the
coin-cell battery out of the computer.
Before Working Inside Your Computer
.
27
Installing the Coin-Cell Battery
1.Place the coin-cell battery into its slot on the system board.
2.Press the coin-cell battery downward until the release latch springs back into place and secures it.
3.Install the:
a) drive cage
b) front bezel
c) cover
4.Follow the procedures in
After Working Inside Your Computer
.
Removing the Heatsink Assembly
1.Follow the procedures in
2.Remove the cover
3.Using both hands, push away the two release handles while lifting the fan shroud upward and off
the computer.
4.Perform the following steps as shown in the illustration:
a) Press the fan cable [1].
b) Disconnect the fan cable from the system board [2].
c) Loosen the captive screws, lift the heat sink assembly and then remove it from the computer.
Before Working Inside Your Computer
.
28
Installing the Heatsink Assembly
1.Place the heat-sink assembly into the chassis.
2.Tighten the captive screws to secure the heat-sink assembly to the system board.
3.Connect the fan cable to the system board.
4.Place the fan shroud on the fan and push to click in place.
5.Install the cover
6.Follow the procedures in
After Working Inside Your Computer
.
Removing the Processor
1.Follow the procedures in
2.Remove the cover.
3.Remove the heat sink assembly.
4.Press the release lever down and then move it outward to release it from the retention hook. Lift
the processor cover and remove the processor from the socket, and place it in antistatic bag.
Before Working Inside Your Computer
.
29
Installing the Processor
1.Insert the processor into the processor socket. Ensure the processor is properly seated.
2.Gently lower the processor cover.
3.Press the release lever down and then move it inward to secure it with the retention hook.
4.Install the heat-sink assembly.
5.Install the cover.
6.Follow the procedures in
After Working Inside Your Computer
.
Removing the Intrusion Switch
1.Follow the procedures in
2.Remove the:
a) cover
b) heat sink assembly
3.Disconnect the intrusion-switch cable from the system board.
4.Slide the intrusion switch toward the bottom of the chassis and remove it from the computer.
Before Working Inside Your Computer
.
Installing the Intrusion Switch
1.Insert the intrusion-switch into the chassis rear and slide it outward to secure it.
2.Connect the intrusion-switch cable to the system board.
3.Install the:
a) heat sink assembly
b) cover
4.Follow the procedures in
30
After Working Inside Your Computer
.
System Board Components
The following image displays the system board layout.
1.PCI Express x16 connector
2.PCI Express x1 connector
3.intrusion-switch connector
4.PS/2, serial connector
5.power connector
6.processor socket
7.CPU fan connector
8.memory module connectors
9.HDD LED & chassis detect connector
10.power switch connector
11.coin-cell battery
12.system power connector
13.system fan connector
14.RTC reset jumper
15.ODD SATA connector
16.HDD SATA connector
17.power connector
18.front i/o connector
19.internal speaker connector
20.password reset jumper
21.front audio connector
31
Removing the System Board
1.Follow the procedures in
2.Remove the:
a) cover
b) front bezel
c) optical drive
d) drive cage
e) memory
f) heat sink assembly
g) expansion card(s)
h) power supply
3.Disconnect all the cables connected to the system board, and move the cables away from the
chassis.
Before Working Inside Your Computer
.
4.Turn the hex screw counter clockwise and remove from the system board
32
5.Lift the cover upward to a 45–degree angle and remove it from the computer.
6.Remove the system board from the chassis.
33
Installing the System Board
1.Align the system board to the port connectors on the rear of the chassis and place the system
board in the chassis.
2.Tighten the screws securing the system board to the chassis.
3.Connect the cables to the system board.
4.Install the:
a) power supply
b) expansion card(s)
c) heat sink assembly
d) memory
e) drive cage
f) optical drive
g) front bezel
h) cover
5.Follow the procedures in
After Working Inside Your Computer
.
34
3
System Setup
System Setup enables you to manage your computer hardware and specify BIOS‐level options. From the
System Setup, you can:
•Change the NVRAM settings after you add or remove hardware
•View the system hardware configuration
•Enable or disable integrated devices
•Set performance and power management thresholds
•Manage your computer security
Boot Sequence
Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a
specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when
the Dell logo appears, you can:
•Access System Setup by pressing <F2> key
•Bring up the one-time boot menu by pressing <F12> key
The one-time boot menu displays the devices that you can boot from including the diagnostic option.
The boot-menu options are:
•Removable Drive (if available)
•STXXXX Drive
NOTE: XXX denotes the SATA drive number.
•Optical Drive
•Diagnostics
NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.
The boot sequence screen also displays the option to access the System Setup screen.
Navigation Keys
The following table displays the system setup navigation keys.
NOTE: For most of the system setup options, changes that you make are recorded but do not take
effect until you re-start the system.
35
Table 1. Navigation Keys
KeysNavigation
Up arrowMoves to the previous field.
Down arrowMoves to the next field.
<Enter>Allows you to select a value in the selected field (if applicable) or follow the link in
the field.
SpacebarExpands or collapses a drop‐down list, if applicable.
<Tab>Moves to the next focus area.
NOTE: For the standard graphics browser only.
<Esc>Moves to the previous page till you view the main screen. Pressing <Esc> in the
main screen displays a message that prompts you to save any unsaved changes and
restarts the system.
<F1>Displays the System Setup help file.
System Setup Options
NOTE: Depending on your computer and its installed devices, the items listed in this section may or
may not appear.
Table 2. General
OptionDescription
System BoardThis section lists the primary hardware
features of your computer.
•System Information
•Memory Information
•PCI Information
•Processor Information
•Device Information
Boot SequenceAllows you to change the order in
which the computer attempts to find an
operating system.
•Boot Sequence
•Diskette drive
•SATA HDD Drive
•USB Storgae Device
•CD/DVD/CD-RW Drive
•Onboard NIC
•Boot List Option
•Allows you to change the boot list
option.
– Legacy
36
OptionDescription
– UEFI
Advanced Boot OptionsAllows you to Enable Legacy Option
ROMs
•Enabled (Default)
Date/TimeAllows you to set the date and time. The
changes to the system date and time
takes effect immediately.
Table 3. System Configuration
OptionDescription
Integrated NICAllows you to configure the integrated network controller. The
options are:
•Disabled
•Enable UEFI Network Stack
•Enabled
•Enabled w/PXE (Default)
•Enabled w/Cloud Desktop
Serial PortIdentifies and defines the serial port settings. You can set the
serial port to:
•Disabled(Default)
•COM1
•COM2
•COM3
•COM4
NOTE: The operating system may allocate resources even if
the setting is disabled.
SATA OperationAllows you to configure the internal SATA hard-drive
controller. The options are:
•Disabled
•ATA
•AHCI (Default)
DrivesAllows you to enable or disable the various drives on-board:
•SATA-0
•SATA-1
•SATA-2
Default Setting: All drives are enabled.
SMART ReportingThis field controls if the hard drive errors for the integrated
drives are reported during system startup. This technology is
37
OptionDescription
part of the SMART (Self Monitoring Analysis and Reporting
Technology) specification.
•Enable SMART Reporting - This option is disabled by
default.
USB ConfigurationAllows you to enable or disable the internal USB configuration.
The options are:
•Enable Boot Support
•Enable Front USB Ports
•Enable USB 3.0 Ports
•Enable Rear Dual USB 2.0 Ports
•Enable Dual USB 2.0 Ports (Under LAN ports)
AudioAllows you enable or disable the audio feature.
Default Setting: Audio is enabled
Table 4. Video
OptionDescription
Multi-DisplayAllows you to enables or disables Multi-
Display, it should be enabled for
windows 7 32/64bit or later only.
•Disable Multi Display
Table 5. Security
OptionDescription
Admin PasswordThis field lets you set, change, or delete the administrator (admin) password
(sometimes called the setup password). The admin password enables several
security features.
The drive does not have a password set by default.
•Enter the old password
•Enter the new password
•Confirm the new password
System PasswordThis field lets you set, change, or delete the system password. The system
password enables several security features.
The drive does not have a password set by default.
•Enter the old password
•Enter the new password
•Confirm the new password
Internal HDD_0
Password
Allows you to set, change, or delete the password on the computer’s internal
hard disk drive (HDD) Successful change to this password take effect
immediately. The drive does not have a password set by default
38
•Enter the old password
OptionDescription
•Enter the new password
•Confirm the new password
Strong Password
Password
Configuration
Password BypassAllows you to bypass the
Password Change Allows you to determine whether changes to the system and hard disk
TPM SecurityThis option lets you control whether the Trusted Platform Module (TPM) in the
Enable strong password - This option is disabled by default.
This field controls the minimum and maximum number of characters allowed
for the admin and system passwords.
•Admin Password Min
•Admin Password Max
•System Password Min
•System Password Max
System Password
prompts during a system restart.
•Disabled - Always prompt for the system and internal HDD password when
they are set. This option is disabled by default.
•Reboot Bypass - Bypass the password prompts on restarts (warm boots).
NOTE: The system will always prompt for the system and internal HDD
passwords when powered on from the off state (a cold boot). Also, the
system will always prompt for passwords on any module bay HDDs that
may be present.
passwords are permitted when an administrator password is set.
•Allow Non-Admin Password Changes - This option is enabled by default.
system is enabled and visible to the operating system.
TPM Security - This option is disabled by default.
TPM ACPI Support
TPM PPI Deprovision Override
Clear
TPM PPI Provision Override
NOTE: Activation, deactivation, and clear options are not affected if you
load the setup program's default values. Changes to this option take effect
immediately.
and the internal HDD password
ComputraceThis field lets you activate or disable the BIOS module interface of the optional
Computrace Service
•Deactivate - This option is disabled by default.
•Disable
•Activate
Chassis Intrusion
CPU XD SupportAllows you to enable or disable the execute disable mode of the processor.
•Disable - This option is disabled by default.
•On-Silent
from
Absolute Software
.
39
OptionDescription
•Enable CPU XD Support - This option is enabled by default.
Admin Setup Lockout Allows you to enable or disable the option to enter setup when an admin
password is set.
•Enable Admin Setup Lockout - This option is not set by default.
HDD Protection
Allows you to enable or disable the HDD Protection feature
Support
•HDD Protection SupportDisable - This option is disabled by default.
Table 6. Secure Boot
OptionDescription
Secure Boot EnableAllows you to enable or disable the
Secure Boot Feature. The options are:
•Disabled (Default)
•Enabled
Expert Key ManagementAllows you to manipulate the security
key databases only if the system is in
Custom Mode. The Enable Custom Mode option is disabled by default. The
options are:
•PK
•KEK
•db
•dbx
If you enable the Custom Mode, the
relevant options for PK, KEK, db, and
appear. The options are:
dbx
40
•Save to File- Saves the key to a user-
selected file
•Replace from File- Replaces the
current key with a key from a userselected file
•Append from File- Adds a key to the
current database from a userselected file
•Delete- Deletes the selected key
•Reset All Keys- Resets to default
setting
•Delete All Keys- Deletes all the keys
NOTE: If you disable the Custom
Mode, all the changes made will be
erased and the keys will restore to
default settings.
Table 7. Performance
OptionDescription
Multi Core SupportSpecifies whether the process will have
one or all cores enabled. The
performance of some applications will
improve with the additional cores.
•All - Enabled by default
•1
•2
Intel SpeedStepAllows you to enable or disable the Intel
C States ControlAllows you to enable or disable the
additional processor sleep states.
Default Setting:Enabled
Limit CPUID ValueThis field limits the maximum value the
processor Standard CPUID Function will
support
•Disable CPUID Limit
NOTE: Some Operating system will
not complete installation when the
maximum CPUID Function is
greater than 3
HyperThread control (SFF)Allows you to enable or disable the
Hyper-Threading Technology. This
option is enabled by default.
Table 8. Power Management
OptionDescription
AC RecoverySpecifies how the computer will respond when AC power is applied after a AC
power loss. You can set the AC Recovery to:
•Power Off (Default)
•Power On
•Last Power State
Auto On TimeAllows you to set the time at which the computer must turn on automatically.
The options are:
•Disabled (Default)
•Every Day
•Weekdays
•Select Days
Deep Sleep ControlAllows you to define the controls when Deep Sleep is enabled.
•Disabled
41
OptionDescription
•Enabled in S5 only
•Enabled in S4 and S5 Enabled
Fan Speed ControlControls the speed of the system fan. This option is disabled by default.
NOTE: When enabled, the fan runs at full speed.
USB Wake SupportThis option allows you to enable USB devices to wake the computer from
standby.
•Enable USB Wake Support - This option is enabled by default.
Wake on LANThis option allows the computer to power up from the off state when triggered
by a special LAN signal. Wake-up from the Standby state is unaffected by this
setting and must be enabled in the operating system. This feature only works
when the computer is connected to AC power supply. The options differ based
on the form factor.
•Disabled - Does not allow the system to power on by special LAN signals
when it receives a wake-up signal from the LAN or wireless LAN.
•LAN Only - Allows the system to be powered on by special LAN signals.
•LAN or PXE Boot - Allows the system to be powered on by special LAN or
PXE Bootsignals. (For Ultra Small Form Factor only)
This option is Disabled by default.
Block SleepAllows you to block entering to sleep (S3 state) in OS Environment.
Default Setting: Disabled
Intel Smart Connect
Technology
The option is disabled by default. If option enables will periodically sense
nearby wireless connection while the system is asleep. It will synchronize
emails or social media application that were open when system entered the
sleep state.
•Smart Connection
Table 9. POST Behavior
OptionDescription
Numlock LEDSpecifies if the NumLock function can be enabled when the system boots. This
option is enabled by default.
Keyboard ErrorsSpecifies whether keyboard related errors are reported when it boots. This
option is enabled by default.
Table 10. Virtualization Support
OptionDescription
VirtualizationThis option specifies whether a Virtual Machine Monitor (VMM) can utilize the
additional hardware capabilities provided by Intel Virtualization technology.
•Enable Intel Virtualization Technology - This option is enabled by default.
42
Table 11. Maintenance
OptionDescription
Service TagDisplays the service tag of your computer.
Asset TagAllows you to create a system asset tag if an asset tag is not already set. This
option is not set by default.
SERR MessagesControls the SERR message mechanism. This option is not set by default. Some
graphics cards require that the SERR message mechanism be disabled.
Table 12. Cloud Desktop
OptionDescription
Server Lookup MethodSpecifies how the ImageServer looks up the server address.
•Static IP
•DNS (enabled by default)
NOTE: This field is only relevant when the
the
System Configuration
Server IP AddressSpecifies the primary static IP address of the ImageServer with which the
client software communicates. The default IP address is 255.255.255.255.
NOTE: This field is only relevant when the
the
System Configuration
and when
Server PortSpecifies the primary IP port of the ImageServer, which is used by the
client to communicate. The default IP port is 06910.
NOTE: This field is only relevant when the
the
Client Address MethodSpecifies how the client obtains the IP address.
•Static IP
•DHCP (enabled by default)
NOTE: This field is only relevant when the
the
Client IP AddressSpecifies the static IP address of the client. The default IP address is
255.255.255.255.
NOTE: This field is only relevant when the
the
and when
Lookup Method
System Configuration
System Configuration
System Configuration
Client DHCP
group is set to
group is set to
is set to
group is set to
group is set to
group is set to
is set to
Static IP
Integrated NIC
Enabled with ImageServer
Integrated NIC
Enabled with ImageServer
Static IP
.
Integrated NIC
Enabled with ImageServer
Integrated NIC
Enabled with ImageServer
Integrated NIC
Enabled with ImageServer
.
control in
control in
control in
control in
control in
.
.
.
Client SubnetMaskSpecifies the subnet mask of the client. The default setting is
255.255.255.255.
NOTE: This field is only relevant when the
the
System Configuration
and when
Client GatewaySpecifies the gateway IP address for the client. The default setting is
255.255.255.255.
Client DHCP
group is set to
is set to
Static IP
Integrated NIC
control in
Enabled with ImageServer
.
43
OptionDescription
NOTE: This field is only relevant when the
the
System Configuration
and when
AdvancedSpecifies for Advanced debugging
•Verbose Mode (Disabled)
NOTE: This Option is only relevant when the integrated NIC control in
the System Configuration group is set to enable with Cloud Desktop.
Table 13. System Logs
OptionDescription
BIOS eventsDisplays the system event log and allows you to clear the log.
•Clear Log
Client DHCP
group is set to
is set to
Static IP
Integrated NIC
control in
Enabled with ImageServer
.
Updating the BIOS
It is recommended to update your BIOS (system setup), on replacing the system board or if an update is
available. For laptops, ensure that your computer battery is fully charged and connected to a power
outlet
1.Re-start the computer.
2.Go to dell.com/support.
3.Enter the Service Tag or Express Service Code and click Submit.
NOTE: To locate the Service Tag, click Where is my Service Tag?
NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the
instructions on screen.
4.If you are unable to locate or find the Service Tag, click the Product Category of your computer.
5.Choose the Product Type from the list.
6.Select your computer model and the Product Support page of your computer appears.
7.Click Get drivers and click View All Drivers.
The Drivers and Downloads page opens.
8.On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.
9.Identify the latest BIOS file and click Download File.
You can also analyze which drivers need an update. To do this for your product, click Analyze
System for Updates and follow the instructions on the screen.
10. Select your preferred download method in the Please select your download method below
window; click Download File.
The File Download window appears.
11. Click Save to save the file on your computer.
12. Click Run to install the updated BIOS settings on your computer.
Follow the instructions on the screen.
44
Clearing Forgotten Password
The system's software security features include a system password and a setup password. The password
jumper disables any password(s) currently in use. There are 3–pins for the password reset jumper.
1.Follow the procedures in
2.Remove the cover.
3.Identify the password reset jumper on the system board, see the System Board Components.
4.Remove the 2-pin jumper plug from pins 2 and 3 and fix it on pins 1 and 2
5.Install the cover.
6.Connect the computer to the electrical outlet and power-on the computer to clear the password.
7.Power-off the computer and disconnect the power cable from the electrical outlet.
8.Remove the cover.
9.Replace the jumper on the pins 2 and 3.
10. Install the cover.
11. Follow the procedures in
12. Power-on the computer.
13. Go to the system setup, and assign a new system or setup password.
Before Working Inside Your Computer
After Working Inside Your Computer
.
.
Clearing CMOS
1.Follow the procedures in
2.Remove the cover.
3.Remove the PCI card if installed.
4.Identify the CMOS jumper on the system board, see the System Board Components.
5.Place the 2-pin jumper plug on pins 1 and 2 to clear CMOS
6.Install PCI card if installed.
7.Install the cover.
8.Connect the computer to the electrical outlet and power-on the computer to clear the CMOS.
9.Power-off the computer and disconnect the power cable from the electrical outlet.
10. Remove the cover.
11. Replace the jumper on the pins 1 and 2.
12. Install PCI card if installed.
13. Install the cover.
14. Follow the procedures in
15. Power-on the computer.
Before Working Inside Your Computer
After Working Inside Your Computer
.
.
System and Setup Password
You can create a system password and a setup password to secure your computer.
Password TypeDescription
System passwordPassword that you must enter to log on to your system.
45
Password TypeDescription
Setup passwordPassword that you must enter to access and make changes to the BIOS settings of
your computer.
CAUTION: The password features provide a basic level of security for the data on your computer.
CAUTION: Anyone can access the data stored on your computer if it is not locked and left
unattended.
NOTE: Your computer is shipped with the system and setup password feature disabled.
Assigning a System Password and Setup Password
You can assign a new System Password and/or Setup Password or change an existing System Password
and/or Setup Password only when Password Status is Unlocked. If the Password Status is Locked, you
cannot change the System Password.
NOTE: If the password jumper is disabled, the existing System Password and Setup Password is
deleted and you need not provide the system password to log on to the computer.
To enter a system setup, press <F2> immediately after a power-on or re-boot.
1.In the System BIOS or System Setup screen, select System Security and press <Enter>.
The System Security screen appears.
2.In the System Security screen, verify that Password Status is Unlocked.
3.Select System Password , enter your system password, and press <Enter> or <Tab>.
Use the following guidelines to assign the system password:
– A password can have up to 32 characters.
– The password can contain the numbers 0 through 9.
– Only lower case letters are valid, upper case letters are not allowed.
– Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).
Re-enter the system password when prompted.
4.Type the system password that you entered earlier and click OK.
5.Select Setup Password, type your system password and press <Enter> or <Tab>.
A message prompts you to re-type the setup password.
6.Type the setup password that you entered earlier and click OK.
7.Press <Esc> and a message prompts you to save the changes.
8.Press <Y> to save the changes.
The computer reboots.
Deleting or Changing an Existing System and/or Setup Password
Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or
change the existing System and/or Setup password. You cannot delete or change an existing System or
Setup password, if the Password Status is Locked.
To enter the System Setup, press <F2> immediately after a power-on or reboot.
1.In the System BIOS or System Setup screen, select System Security and press <Enter>.
46
The System Security screen is displayed.
2.In the System Security screen, verify that Password Status is Unlocked.
3.Select System Password, alter or delete the existing system password and press <Enter> or <Tab>.
4.Select Setup Password, alter or delete the existing setup password and press <Enter> or <Tab>.
NOTE: If you change the System and/or Setup password, re-enter the new password when
promoted. If you delete the System and/or Setup password, confirm the deletion when
promoted.
5.Press <Esc> and a message prompts you to save the changes.
6.Press <Y> to save the changes and exit from the System Setup.
The computer reboots.
Disabling a System Password
The system's software security features include a system password and a setup password. The password
jumper disables any password(s) currently in use.
NOTE: You can also use the following steps to disable a forgotten password.
1.Follow the procedures in
2.Remove the cover.
3.Identify the PSWD jumper on the system board.
4.Remove the PSWD jumper from the system board.
NOTE: The existing passwords are not disabled (erased) until the computer boots without the
jumper.
5.Install the cover.
NOTE: If you assign a new system and/or setup password with the PSWD jumper installed, the
system disables the new password(s) the next time it boots.
6.Connect the computer to the electrical outlet and power-on the computer.
7.Power-off the computer and disconnect the power cable from the electrical outlet.
8.Remove the cover.
9.Replace the PSWD jumper on the system board.
10. Install the cover.
11. Follow the procedures in
12. Power-on the computer.
13. Go to the system setup, and assign a new system or setup password. See
Password
.
Before Working on Your Computer
After Working on Your Computer
.
.
Setting up a System
47
48
4
Diagnostics
If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for
technical assistance. The purpose of running diagnostics is to test your computer's hardware without
requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service
and support personnel can use the diagnostics results to help you solve the problem.
Enhanced Pre-Boot System Assessment (ePSA)
Diagnostics
The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.
The ePSA is embedded with the BIOS and is launched by the BIOS internally. The embedded system
diagnostics provides a set of options for particular devices or device groups allowing you to:
•Run tests automatically or in an interactive mode
•Repeat tests
•Display or save test results
•Run thorough tests to introduce additional test options to provide extra information about the failed
device(s)
•View status messages that inform you if tests are completed successfully
•View error messages that inform you of problems encountered during testing
CAUTION: Use the system diagnostics to test only your computer. Using this program with other
computers may cause invalid results or error messages.
NOTE: Some tests for specific devices require user interaction. Always ensure that you are present
at the computer terminal when the diagnostic tests are performed.
1.Power-on the computer.
2.As the computer boots, press the <F12> key as the Dell logo appears.
3.On the boot menu screen, select the Diagnostics option.
The Enhanced Pre-boot System Assessment window is displayed, listing all devices detected in the
computer. The diagnostics starts running the tests on all the detected devices.
4.If you wish to run a diagnostic test on a specific device, press <Esc> and click Yes to stop the
diagnostic test.
5.Select the device from the left pane and click Run Tests.
6.If there are any issues, error codes are displayed.
Note the error code and contact Dell.
49
50
5
Troubleshooting Your Computer
You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error
Messages during the operation of the computer.
Power LED Diagnostics
The power button LED located on the front of the chassis also functions as a bicolored diagnostic LED.
The diagnostic LED is only active and visible during the POST process. Once the operating system starts
to load, it is no longer visible.
Amber LED blinking scheme – The pattern is 2 or 3 blinks followed by a short pause then x number of
blinks up to 7. The repeated pattern has a long pause inserted in the middle. For example 2,3 = 2 amber
blinks, short pause, 3 amber blinks followed by long pause then repeats.
Table 14. Power LED Diagnostics
Amber LED StateWhite LED StateDescription
offoffsystem is OFF
offbreathingsystem is in sleep state
blinkingoffpower supply unit (PSU) failure
steadyoffPSU is working but failed to fetch code
offsteadysystem is ON
Amber LED StateDescription
2,1system board failure
2,2system board, PSU or PSU cabling failure
2,3system board, memory or CPU failure
2, 4coin-cell battery failure
2,5corrupt BIOS
2,6CPU configuration failure or CPU failure
2,7memory modules are detected, but a memory failure
3,1possible peripheral card or system board failure
3,2possible USB failure
3,3no memory modules are detected
3,4possible system board error
3,5memory modules are detected, but a memory configuration or compatibility error
51
Amber LED StateDescription
3,6possible system board resource and/or hardware failure
3,7some other failure with messages on screen
Beep Code
The computer can emit a series of beeps during start-up if the display does not show errors or
problems. These series of beeps, called beep codes, identify various problems. The delay between each
beep is 300 ms, the delay between each set of beeps is 3 sec, and the beep sound lasts 300 ms. After
each beep and each set of beeps, the BIOS should detect if the user presses the power button. If so,
BIOS will jump out from looping and execute the normal shutdown process and power system.
Code1-3-2
CauseMemory failure
NOTE: 1. If the system is attached with an internal speaker we can hear the beep sound directly.
NOTE: 2. If the system does have an internal speaker, connect an external speaker to line out
connection to hear the beep sound.
NOTE: User can also check the power LED behavior instead of the beep code for troubleshooting
purpose.
Error Messages
Error MessageDescription
Address mark not
found
Alert! Previous
attempts at
booting this
system have failed
at checkpoint
[nnnn]. For help in
resolving this
problem, please
note this
checkpoint and
contact Dell
Technical Support.
Alert! Security
override Jumper is
installed.
Attachment failed
to respond
The BIOS found a faulty disk sector or could not find a particular disk sector.
The computer failed to complete the boot routine three consecutive times for the
same error. Contact Dell and report the checkpoint code (nnnn) to the support
technician
The MFG_MODE jumper has been set and AMT Management features are disabled
until it is removed.
The floppy or hard drive controller cannot send data to the associated drive.
52
Error MessageDescription
Bad command or
file name
Bad errorcorrection code
(ECC) on disk read
Controller has
failed
Data errorThe floppy or hard drive cannot read the data. For the Windows operating system,
Decreasing
available memory
Diskette drive 0
seek failure
Diskette read
failure
Diskette
subsystem reset
failed
Gate A20 failureOne or more memory modules may be faulty or improperly seated. Reinstall the
Ensure that you have spelled the command correctly, put spaces in the proper
place, and used the correct pathname.
The floppy or hard drive controller detected an uncorrectable read error.
The hard drive or the associated controller is defective.
run the chkdsk utility to check the file structure of the floppy or hard drive. For
any other operating system, run the appropriate corresponding utility.
One or more memory modules may be faulty or improperly seated. Re-install the
memory modules and, if necessary, replace them.
A cable may be loose or the computer configuration information may not match
the hardware configuration.
The floppy disk may be defective or a cable may be loose. If the drive access light
turns on, try a different disk.
The floppy drive controller may be faulty.
memory modules and, if necessary, replace them.
General failureThe operating system is unable to carry out the command. This message is usually
followed by specific information—for example, Printer out of paper. Take the
appropriate action to resolve the problem.
Hard-disk drive
configuration
error
Hard-disk drive
controller failure
Hard-disk drive
failure
Hard-disk drive
read failure
Invalid
configuration
informationplease run SETUP
program
Invalid Memory
configuration,
The hard drive failed initialization.
The hard drive failed initialization.
The hard drive failed initialization.
The hard drive failed initialization.
The computer configuration information does not match the hardware
configuration.
DIMM1 slot does not recognize a memory module. The module should be reseated or installed.
53
Error MessageDescription
please populate
DIMM1
Keyboard failureA cable or connector may be loose, or the keyboard or keyboard/mouse
controller may be faulty.
Memory address
line failure at
address, read
value expecting
value
Memory allocation
error
Memory data line
failure at address,
read value
expecting value
Memory double
word logic failure
at address, read
value expecting
value
Memory odd/even
logic failure at
address, read
value expecting
value
Memory write/
read failure at
address, read
value expecting
value
A memory module may be faulty or improperly seated. Reinstall the memory
modules and, if necessary, replace them.
The software you are attempting to run is conflicting with the operating system,
another program, or a utility.
A memory module may be faulty or improperly seated. Reinstall the memory
modules and, if necessary, replace them.
A memory module may be faulty or improperly seated. Reinstall the memory
modules and, if necessary, replace them.
A memory module may be faulty or improperly seated. Reinstall the memory
modules and, if necessary, replace them
A memory module may be faulty or improperly seated. Reinstall the memory
modules and, if necessary, replace them.
Memory size in
CMOS invalid
Memory tests
terminated by
keystroke
No boot device
available
No boot sector on
hard-disk drive
No timer tick
interrupt
54
The amount of memory recorded in the computer configuration information does
not match the memory installed in the computer.
A keystroke interrupted the memory test.
The computer cannot find the floppy disk or hard drive.
The computer configuration information in System Setup may be incorrect.
A chip on the system board might be malfunctioning.
Error MessageDescription
Non-system disk
or disk error
Not a boot
diskette
Plug and play
configuration
error
Read faultThe operating system cannot read from the floppy or hard drive, the computer
Requested sector
not found
Reset failedThe disk re-set operation failed.
Sector not foundThe operating system cannot locate a sector on the floppy or hard drive.
Seek errorThe operating system cannot find a specific track on the floppy disk or hard drive.
Shutdown failureA chip on the system board might be malfunctioning.
Time-of-day clock
stopped
Time-of-day not
set-please run the
System Setup
program
The floppy disk in drive A does not have a bootable operating system installed on
it. Either replace the floppy disk with one that has a bootable operating system, or
remove the floppy disk from drive A and restart the computer.
The operating system is trying to boot to a floppy disk that does not have a
bootable operating system installed on it. Insert a bootable floppy disk.
The computer encountered a problem while trying to configure one or more
cards.
could not find a particular sector on the disk, or the requested sector is defective.
The operating system cannot read from the floppy or hard drive, the computer
could not find a particular sector on the disk, or the requested sector is defective.
The battery might be dead.
The time or date stored in System Setup does not match the computer clock.
Timer chip
counter 2 failed
Unexpected
interrupt in
protected mode
WARNING: Dell's
Disk Monitoring
System has
detected that drive
[0/1] on the
[primary/
secondary] EIDE
controller is
operating outside
of normal
specifications. It is
advisable to
immediately back
up your data and
replace your hard
A chip on the system board may be malfunctioning.
The keyboard controller may be malfunctioning or a memory module may be
loose.
During initial startup, the drive detected possible error conditions. When your
computer finishes booting, immediately back up your data and replace your hard
drive (for installation procedures, see "Adding and Removing Parts" for your
computer type). If no replacement drive is immediately available and the drive is
not the only bootable drive, enter System Setup and change the appropriate drive
setting to None. Then remove the drive from the computer.
55
Error MessageDescription
drive by calling
your support desk
or Dell.
Write faultThe operating system cannot write to the floppy or hard drive.
Write fault on
selected drive
The operating system cannot write to the floppy or hard drive.
56
Technical Specifications
NOTE: Offerings may vary by region. The following specifications are only those required by law to
ship with your computer. For comprehensive specification of your computer go to Specifications’
section in your Owner’s Manual available on the support site at dell.com/support. For more
information about the configuration of your computer, go to Help and Support in your Windows
operating system and select the option to view information about your computer.
Serialsupport Serial / PS/2 Add-in Bracket or Serial / Parallel Port
PCIe Add-in Card
ParallelSerial / Parallel Port PCIe Add-in Card
USB 2.0two connectors in the front panel and four connectors on
the back panel
USB 3.0two connectors on the back panel
Table 22. Controls and Lights
FeatureSpecification
Front of the computer:
Power button lightWhite light — Solid white light indicates power-on state;
Breathing white light indicates sleep state of the computer.
Drive activity lightWhite light — Blinking white light indicates that the
computer is reading data from or writing data to the hard
drive
Back of the computer:
Link integrity light on integrated
network adapter
Green — a good 10 Mbps connection exists between the
network and the computer.
Green — a good 100 Mbps connection exists between the
network and the computer.
Orange — a good 1000 Mbps connection exists between
the network and the computer.
58
FeatureSpecification
Off (no light) — the computer is not detecting a physical
connection to the network.
Network activity light on integrated
network adapter
Yellow light — A blinking yellow light indicates that network
activity is present.
Power supply diagnostic lightGreen light — The power supply is turned on and is
functional. The power cable must be connected to the
power connector (at the back of the computer) and the
electrical outlet.
Table 23. Power
FeatureSpecification
Coin-cell battery3V Lithium CR2032
Voltage100 VAC to 240 VAC
Wattage255 W
Maximum heat dissipationN/A
NOTE: Heat dissipation is calculated by using the power supply wattage rating.
Table 24. Physical
FeatureSpecification
Height290.00 mm (11.41 inches)
Width92.60 mm (3.64 inches)
Depth312.00 mm (12.28 inches)
Weight5 kg (11.02 lb)
Table 25. Environmental
FeatureSpecification
Temperature:
Operating0 degree to 35 degree
Storage-40 degree to 65 degree
Relative humidity (maximum):
Operating20 R.H. to 80 R.H.
Storage20 R.H. to 95 R.H.
Maximum vibration:
Operating0.26 Grms
Storage1.37 Grms
Maximum shock:
Operating40 G/2 ms
Storage50 G/19 ms
59
FeatureSpecification
Altitude:
Operating–15.2 m to 3048 m (–50 to 10,000 ft)
Storage–15.20 m to 10,668 m (–50 ft to 35,000 ft)
Airborne contaminant levelG1 or lower as defined by ANSI/ISA-S71.04-1985
60
Contacting Dell
NOTE: If you do not have an active Internet connection, you can find contact information on your
purchase invoice, packing slip, bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by
country and product, and some services may not be available in your area. To contact Dell for sales,
technical support, or customer service issues:
1.Go to dell.com/contactdell.
2.Verify your country or region from the drop-down menu at the top left corner of the page.
3.Select your support category: Technical Support, Customer Support, Sales, or International
Support Services.
4.Select the appropriate service or support link based on your requirement.
NOTE: If you have purchased a Dell system, you may be asked for the Service Tag.
7
61
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.