dbx Pro 2031 User Manual

160SL

Stereo Compresssor / Limiter with AutoVelocity™

8760 S. Sandy Pkwy.

Sandy, Utah 84070

Phone (801) 568-7660

Fax (801) 568-7662

Int’l Fax (801) 568-7583

customer@dbxpro.com

http://www.dbxpro.com

A Harman International Company

• Revolutionary instant encode/decode Type III Noise Reduction in-circuit at the push of a button. Increases S/N ratio by up to 20dB.

• Patent-pending PeakPlus™ Limiter threshold range from 0dBu to +24dBu (off) can transparently tame the wildest hits or the subtlest nuances of any signal.

• An extremely high quality EQ, patentpending TYPE III Noise Reduction, and the elegant new PeakPlus™ Limiter all in one great sounding box.

• Four segment LED bargraph for BOTH Gain Reduction AND Output Level offers the most comprehensive visual feedback available.

• Status LEDs offer visual feedback for all settings on the front panel.

It’s amazing. One little button. So much effect. dbx Type III Noise Reduction is an entirely new concept... virtually instantaneous encode/decode within the circuitry of the box. We started out to build the finest EQs possible, boxes with the heritage and performance to rival our famous 30 Series EQs. And to no one’s surprise they came out awfully darn good. (Ask to see the Audio Precision plots compared to the competition.) But then, Roger (our chief engineer, a nice guy, as far as engineers go) got the crazy idea of putting this new noise reduction stuff in the box. We listened to it and were amazed. The EQs sounded great without it but with it the performance was nothing short of incredible. Check it out yourself and see.

18-1719-B 01/99

But hey, Roger wasn’t about to stop there. PeakPlus™ Limiter. Who knows more about limiting than the folks at dbx; nobody... that’s who. So when the guys were developing this new series of EQs they wanted something that would be unique to these EQs. That’s when Roger got another one of his bright ideas and said “I bet they’ll work a lot better if there’s a cool limiter built in.” Next thing you know, all the guys are in the studio amazed at the new limiter Roger had designed specially for the 20 Series. Once again, hearing is believing... With a threshold range of 0dbu to plus 20dbu, the patent-pending PeakPlus™ limiter is designed to tame your program material from the subtlest nuances to the rowdiest hits. Also, the four stage LED ladder gives you a great visual indication as to what the limiter is doing.

20 Series EQs. You used to have to settle for second best in a reasonably priced EQ but not any more. With the new 20 Series from dbx Professional Products you get a great EQ circuit, a graceful yet powerful limiter and the revolutionary new design of the Type III Noise Reduction. Check out the dbx 20 Series graphic EQs at your pro audio outfitter. You’ll see, with the 20 Series EQs you get MORE!!!

III

2031

Equalizer/Limiter

with TYPE

+15

-15

20 25 31.5 40 50 63 80 500400315250 1.6k1.25k1k800 5k4k3.15k2.5k 16k12.5k10k8k6.3k 20k2k630100 125 160 200

1 3610+18+100-10

+/-15

GAIN

REDUCTION (dB)

OUTPUT

LEVEL (dBu)

CLIP

-6

+/-6

+20+5

RANGE

+15+10

dBu

PeakPlus

0OFF

THRESHOLD

CUT

LOW

+12

GAIN

INPUT

-12

BYPASS

III

TYPE

160SL

Stereo Compresssor / Limiter with AutoVelocity™

FOR MORE INFORMATION CONTACT:

dbx Professional Products

8760 S. Sandy Pkwy.

Sandy, Utah 84070

Phone (801) 568-7660

Fax (801) 568-7662

Int’l Fax (801) 568-7583

customer@dbxpro.com

http://www.dbxpro.com

A Harman International Company

The graphic equalizer shall be a mono 31-band type with frequency centers on standard ISO one-third octave frequencies ranging from 20Hz to 20kHz. The boost/cut range shall be switchable via a recessed front panel switch to either +/-6dB or +/-15dB and the selected range shall be indicated on the front panel by either of two LEDs. Low-noise equalization sliders having a 45mm travel shall be utilized having center detents at 0dB. The equalizer shall have a front panel 41-detent rotary input gain control having a +/15dB range. Bypassing the equalizer section of the signal path shall be accomplished via a front-panel switch having a corresponding LED to indicate when it is bypassed. A 40Hz low-cut Bessel filter with 18dB/octave slope shall be insertable in the signal path via a front panel recessed switch and shall have an LED to indicate when the filter is active.

The graphic equalizer shall incorporate dbx Type III™ Noise Reduction providing up to 20dB of broadband noise reduction, having a front panel switch to enable the noise reduction and an LED to indicate when it is active. The equalizer shall also be equipped with a dbx PeakPlus™ limiter system having a front panel 41-detent rotary limiter threshold control varying from 0 to +24dBu (off) and a four-LED gain reduction bar graph calibrated to read 0, 3, 6, and 10dB. Output level shall be monitored on a fourLED peak-reading bar graph calibrated to read -10, 0, +10, and +18dBu.

Electronically balanced/unbalanced inputs shall include 1/4" TRS, female XLR, and screw terminal barrier strip, while servo-balanced/unbalanced outputs shall include 1/4" TRS, male XLR, and screw terminal barrier strip shared with the input. A circuit/chassis ground lift jumper shall be strapped across circuit ground and chassis ground screw terminals and shall be removable by the user. Inputs shall be electronically balanced/unbalanced and RF filtered having a nominal input impedance not less than 40kΩ balanced and 20kΩ unbalanced, and shall accept maximum signal levels of not less than +21dBu. Outputs shall be servo-balanced/unbalanced and RF filtered having a nominal output impedance of not more than 200Ω balanced and 100Ω unbalanced, and shall be capable of driving not less than +21dBu into 2kΩ or greater and not less than +20dBm (into 600Ω) continuously.

Frequency response shall be better than 10Hz to 50kHz, +0.5/-3dB. Signal-to-noise ratio shall be greater than 90dB, referenced to +4dBu, in either boost/cut range with noise reduction disabled and shall be greater than 102dB with noise reduction enabled. THD+Noise shall be less than 0.04% with a 1kHz signal at +4dBu.

The internal power supply shall be constructed using a thermally-fused transformer mounted in a low hum orientation and shall be magnetically isolated from equalizer circuitry by means of a mu-metal shield. The power cord shall be detachable from an international standard IEC 320 power inlet receptacle. Unit shall be constructed to meet or exceed all applicable international safety and regulatory agencies. Domestic unit shall be powered from 100VAC 50/60Hz, 120VAC 60Hz, while international unit shall be powered from 230VAC 50/60Hz. Unit shall consume no more than 12W. Housing shall be of all steel/aluminum construction and shall be rack-mountable in an IEC standard 19” rack and shall occupy a 2U (3.5") rack space. The unit shall be a dbx 2031 Equalizer/Limiter with Type III Noise reduction.

dbx engineers are constantly working to improve the quality of our products. Specifications are, therefore subject to change without notice.

2031

Inputs

Connectors: 1/4” TRS, female XLR (pin 2 hot), and

barrier terminal strip

Type: Electronically balanced/unbalanced, RF

filtered

Impedance: Balanced 40kΩ, unbalanced 20kΩ Max Input Level: >+21dBu balanced or unbalanced CMRR: >40dB, typically >55dB at 1kHz

Outputs

Connectors: 1/4” TRS, male XLR (pin 2 hot), and bar-

rier terminal strip

Type: Impedance-balanced/unbalanced, RF fil-

tered

Impedance: Balanced 200Ω, unbalanced 100Ω Max Output Level: >+21dBu balanced/unbalanced into 2kΩ

or greater >+18dBm balanced/unbalanced (into 600Ω)

System Performance

Bandwidth: 20Hz to 20kHz, +/-0.5dB Frequency Response: <10Hz to >50kHz, +0.5/-3dB

Noise Reduction In (+/-6 and +/-15dB range):

Signal-to-Noise: >102dB, unweighted, ref: +4dBu, 22kHz

measurement bandwidth

Dynamic Range: >120dB, unweighted

Noise Reduction Out: (+/-6dB range):

Signal-to-Noise: >94dB, unweighted, ref: +4dBu, 22kHz

measurment bandwidth

Dynamic Range: >112dB, unweighted

Noise Reduction Out: (+/-15dB range):

Signal-to-Noise: >90dB, unweighted, ref: +4dBu, 22kHz

measurement bandwidth Dynamic Range: >108dB, unweighted THD+Noise: <0.04%, 0.02% typical at +4dBu, 1kHz Noise Reduction: Up to 20dB of dynamic broadband noise

reduction

Function Switches

Type III NR: Activates dbx Type III Noise Reduction EQ Bypass: Bypasses the graphic equalizer section

in the signal path

Low Cut (recessed): Activates the 40Hz 18dB/octave Bessel

high-pass filter

Range (recessed): Selects either +/- 6dB or +/- 15dB slider

boost/cut range

Indicators

Output Level Meter: 4-LED bar graph (Green, Green, Yellow,

Red) at -10, 0, +10, and +18dBu

Gain Reduction Meter: 4-LED bar graph (all Red) at 0, 3, 6, and

10dB Type III NR Active: Yellow LED EQ Bypass: Red LED Clip: Red LED Low Cut Active: Red LED +/-6dB range: Yellow LED +/-15dB range: Red LED

Power Supply

Operating Voltage: 100VAC 50/60Hz, 120VAC 60Hz

230VAC 50/60Hz Power Consumption: 12W Mains Connection: IEC receptacle

Physical

Dimensions: 3.5" H X 19" W X 7.9" D (8.9cm x

48.3cm x 20.1cm) Weight: 8.5 lbs. (3.9 kg) Shipping Weight: 9.5 lbs. (4.3 kg)

Note: Specifications subject to change.

586

Dual Vacuum Tube Preamp

TYPE IV™ Conversion System

704

SINGLE CHANNEL 31 BAND EQUALIZER / LIMITER WITH TYPE III NOISE REDUCTION

20 25 31.5 40 50 63 80 500400315250 1.6k1.25k1k800 5k4k3.15k2.5k 16k12.5k10k8k6.3k 20k2k630100 125 160 200

3610+18+100-10

GAIN

OUTPUT

REDUCTION (dB)

LEVEL (dBu)

CLIP

-120+12

TYPE

III

INPUT

BYPASS

GAIN

+/-15

+15+10

+/-6

+20+5

0 OFF

dBu

RANGE

LOW

PeakPlus

CUT

THRESHOLD

-6

+15

Equalizer/Limiter

with TYPE

-15

2031

III

CAUTION: TO REDUCE

POWER

24 WATTS

100V 50/60Hz

120V 60Hz

THE RISK OF FIRE REPLACE ONLY WITH SAME TYPE FUSE.

ATTENTION: UTILISER

UN FUSIBLE DE RECHANGE DE MEME TYPE.

PROFESSIONAL PRODUCTS A HARMAN INTERNATIONAL COMPANY MODEL 2215 EQUALIZER/LIMITER WITH TYPE III NOISE REDUCTION

MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 4,234,804 4,316,107 4,329,598 4,331,931 4,377,792 4,403,199 4,409,500 4,425,551 4,434,380 4,454,433 4,471,324 4,473,793 OTHER PATENTS PENDING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE

CONNECTOR POLARITY

PHONE:

XLR:

TIP

PIN 1

RING

PIN 2

SLEEVE

PIN 3

®

OUTPUT INPUT

CHANNEL 1

OUTPUT

CHANNEL 2

OUTPUT

INPUTOUTPUT

INPUT

INPUTOUTPUT

INPUT