Datasheet VNL08C351-INV Datasheet (TOSHIBA)

All information is subject to change without notice. Please read bottom notes.

TOSHIBA MATSUSHITA DISPLAY TECHNOLOGY

PRODUCT INFORMATION

INVERTER for LTM08C351

VNL08C351-INV

TENTATIVE

MECHANICAL SPECIFICATIONS

Item Specifications
Dimensional Outline (Typ.) 110.0(W) x 22.0(H) x 10.0(Max.)(D) mm
Applicable TFT Module LTM08C351(8.4 Type SVGA)
Weight (approximately) 25g(Typ.)

ABSOLUTE MAXIMUM RATINGS *1

Item Symbol Min. Max. Unit
Supply Voltage VIN 0 14.0 V
Input Voltage

Operating Temperature *2
Storage Temperature *2
Storage Humidity *2

*1 : Do not exceed the maximum rating values under the worst probable conditions
taking into account the supply voltage variation, input voltage variation,
variation in part constants, ambient temperature and so on.
Otherwise the inverter unit may be damaged.
*2 : Wet bulb temperature should be 39°C max.,and no condensation of water.

VON/V

T

Top

H

stg

OFF

-1 VIN+1 kHz
0 50 °C

-20 60 °C
10 90 %(RH)

ELECTRICAL SPECIFICATION *3

Item Symbol Min. Typ. Max. Unit
Supply Voltage

Input Current
Open Output Voltage
Frequency

Volume Max. --- 12.0 --- mA(rms) Output Current *4
Volume Min.

*3 : The characteristics without remarks are measured on condition with Vin=12V and VR-VR:short.
*4 : This is the sum of two output currents.

V

V

OPEN

VON 2.5 --- VIN V V ON/OFF Signal Voltage

V

IN

I

IN

f

IFL

OFF

10.8 12.0 13.2 V

--- 550 900 mA

1400 --- --- Vo-p

40 45 50 kHz

--- 5.5 --- mA(rms)

--- --- 0.7 V

*The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by
Toshiba Matsushita Display Technology or other rights of the third parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of Toshiba Matsushita Display Technology or others.

*The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba Matsushita
Display Technology before proceeding with the design of equipment incorporating this product.

(1/4) 2003-02-07 (Ver.2.0)

DIMENSIONAL OUTLINE

VNL08C351-INV

Unit : mm
Standard tolerance : ±0.5

(2/4) 2003-02-07 (Ver.2.0)

SCHEMATIC DIAGRAM OF INVERTER CONNECTION

VNL08C351-INV

(3/4) 2003-02-07 (Ver.2.0)

VNL08C351-INV

CONNECTOR PIN ASSIGNMENT FOR INTERFACE

CN1 INPUT SIGNAL

Connector : 53261-0890/JAPAN MOLEX CO., LTD.
Mating Connector : 51021-0800

Terminal No. Symbol Function

1
2
3 GND 1) 0V
4 GND 1) 0V
5 ON/OFF “H” : FL ON “L” : FL OFF
6 VR
7 VR
8

VIN
VIN

Vst

Supply Voltage : 12.0V(Typ.) (10.8 13.2V)
Supply Voltage : 12.0V(Typ.) (10.8 13.2V)

Connect the Potentiometer (50kΩ) between VR(Pin No.6) and VR(Pin No.7)
Connect the Potentiometer (50kΩ) between VR(Pin No.6) and VR(Pin No.7)
The Warning Signal : 5V in abnormal circumstances

CN2 CCFL POWER SOURCE

Connector : SM04(4.0)B-BHS-1/JAPAN SOLDERLESS TERMINAL MFG CO., LTD.

Terminal No. Symbol Function

1
2
3 NC 2)
4

*1 : Please connect GND pin to ground.
Don’t use it as no-connect nor connection with high impedance.
*2 : NC Terminal is open. (Don't use)

VFLH1 Output Power Supply for VFLH1 (High Voltage)
VFLH2 Output Power Supply for VFLH2 (High Voltage)

VFLL Output Power Supply for VFLL (Low Voltage)

(4/4) 2003-02-07 (Ver.2.0)