Page 1
The facon AC. motor start capacitors are non-polar aluminium electrolytic capacitors designed for intermittent AC. duty, more
specifically, the starting of small AC. motors.
Other applications:
• filtering alternating current (for ex: soldering units) - f 20 KHz
• filtering V.DC with high superimposed V.AC - f 1 KHz
• continuous voltage with reversed polarity
• on request, some values can be used under continuous V.AC 48 V - f = 50 ÷ 20.000 Hz - see enclosure 3/A
➀ Capac. type 04P - ➁ End cap - ➂ Metal bracket: Four different mounting positions for capacitors size 3 and 4 - One position
for size 5 and 6. See dimensions table 1) in the next page.
Electrolytic motor start capacitors
These capacitors are interely realized with plastic case and are assembled with automatic machines to guarantee a constant quality.
Facon type 04P. capacitors are normally supplied with end cup and double faston terminals (6.3 x 0.8 mm.). On request: simple
faston, bipolar cable, discharge resistance, metal mounting bracket for capacitors size 3,4,5 - fixing stud M8x10 mm. for
capacitors size C,D,E.
Applications
Manufacturing
See tables 2) 3) and enclosure 1/A. NEW UL/CSA, all the serie 04P UL/CSA APPROVED, upon customer’s request.
Technical characteristics
Using the circuit shown in fig. 1, apply rated voltage to the capacitor and measure current and dissipated power. Current will be
measured after 2÷3 seconds, dissipated power within 3 seconds after application of rated voltage. Capacitance and power factor
must be calculated with the following formula:
Note: to have the right measurements is required a special type of instruments.
Please, inquire for information about different duty cycles or particular applications.
Measurements
Other characteristic
Fig.1
C = capacitance in m F
I = current in amperes
π = constant 3.14
f = frequency in hertz
V = applied voltage
PF = power factor
W = dissipated power in Watts
C=
l •10
6
2
•π•f•
V
PF%=
w •100
V
•
I
where:
50÷60 Hz AC.
➀
➁
➂
Page 2
I2 330 - 0 +20% -10 +55°C 60 3'/1.7%
- 0 +20% -10 +55°C 60 3'/1.7%
CASE, APPROVAL AND ARTICLE CODES FOR
25 36.5x70 2 C 19638.12P2D 36.5x70 2 19638.12P2V
31.5 36.5x70 2 C 19638.16P2D 36.5x70 2 19638.16P2V
40 36.5x70 2 C 19638.20P2D 36.5x70 2 19638.20P2V
50 36.5x70 2 C 19638.30P2D 36.5x70 2 19638.30P2V
64 36.5x70 2 C 19638.44P2D 36.5x70 2 19638.44P2V
80 36.5x70 2 C 19638.60P2D 36.5x70 2 19638.60P2V
100 36.5x98 3/C C 19638.80P#D 36.5x70 2 19638.80P2V
125 36.5x98 3/C C 19638.C5P#D 36.5x70 2 19638.C5P2V
156 36.5x98 3/C C 19638.E6P#D 36.5x70 2 19638.E6P2V
200 36.5x98 3/C C 19638.H0P#D 36.5x70 2 19638.H0P2V
250 46x98 4/D C 19638.K0P#D 36.5x98 3/C 19638.KOP#V
315 46x98 4/D C 19638.P5P#D 36.5x98 3/C 19638.P5P#V
400 46x124 5/E C 19638.T0P#D
500 46x124 5/E C 19638.X0P#D
600 52x124 6 C 19638.W0P#D
25 36.5x70 2/C C 19642.12P2D 36.5x70 2 19642.12P2V
31.5 36.5x70 2/C C 19642.16P2D 36.5x70 2 19642.16P2V
40 36.5x70 2/C C 19642.20P2D 36.5x70 2 19642.20P2V
50 36.5x70 2/C C 19642.30P2D 36.5x70 2 19642.30P2V
64 36.5x98 3/C C 19642.44P#D 36.5x70 2 19642.44P2V
80 36.5x98 3/C C 19642.60P#D 36.5x70 2 19642.60P2V
100 36.5x98 3/C C 19642.80P#D 36.5x70 2 19642.80P2V
125 36.5x98 3/C C 19642.C5P#D 36.5x70 2 19642.C5P2V
156 36.5x98 3/C C 19642.E6P#D 36.5x70 2 19642.E6P2V
200 46x98 4/D C 19642.H0P#D 36.5x98 3/C 19642.H0P#V
250 46x98 4/D C 19642.K0P#D
315 46x98 4/D C 19642.P5P#D
400 46x124 5/E C 19642.T0P#D
500 46x124 5/E C 19642.X0P#D
600 52x124 6 C 19642.W0P6D
16 36.5x70 2 C 19645.04P2D 36.5x70 2 19645.04P2V
21 36.5x70 2 C 19645.08P2D 36.5x70 2 19645.08P2V
25 36.5x70 2 C 19645.12P2D 36.5x70 2 19645.12P2V
31.5 36.5x70 2 C 19645.16P2D 36.5x70 2 19645.16P2V
40 36.5x98 3/C C 19645.20P#D 36.5x70 2 19645.20P2V
50 36.5x98 3/C C 19645.30P#D 36.5x70 2 19645.30P2V
64 36.5x98 3/C C 19645.44P#D 36.5x70 2 19645.44P2V
80 36.5x98 3/C C 19645.60P#D 36.5x70 2 19645.60P2V
100 36.5x98 3/C C 19645.80P#D 36.5x98 3/C 19645.80P#V
125 46x98 4/D C 19645.C5P#D 36.5x98 3/C 19645.C5P#V
156 46x98 4/D C 19645.E6P#D
200 46x98 4/D C 19645.H0P#D
250 46x124 5/E C 19645.K0P#D
315 46x124 5/E C 19645.P5P#D
400 52x124 6 C 19645.T0P6D
500 52x124 6 C 19645.X0P6D
600 52x124 6 C 19645.W0P6D
DIMENSION TABLE
CASE CODE D L
FLAT
BOTTOM
FIXING
STUD
±1.5 mm
±1.5 mm
2 - 36.5 70*
3 C 36.5 98
4 D 46 98
5 E 46 124
6 - 52 124
*** Quote L without CAP; normally supplied
without plastic-cap because of metal bracket not
available for this lenght.
APPROVALS TABLE 2)
APPROVALS
APPR.
CODE
V.ac
CAPACITANCE
TOLERANCE
CLIMATIC
CATEGORY
NT
DUTY
CYCLE
US FILE E219374, on request.
V1 250 - 0 +20% -10 +65°C 60 3'/1.7%
V2 330 - 0 +20% -10 +55°C 60 3'/1.7%
I1 250 - 0 +20% -10 +65°C 60 3'/1.7%
VDE EN60252-2
IMQ EN 60252-2
C= CONFORMING WITH EN60252-2
INDUSTRIAL APPLIANCE HOUSEHOLD APPLIANCES
V.ac
C
(µF)
D x L
(mm)
CASE
CODE
APPROVALS
CODE
ARTICLE
CODE
D X L
(mm)
CASE
CODE
ARTICLE
CODE
110-125
160-165
220
Page 3
25 36.5 x98 3/C V1 I1 19647.12P#D 36.5x70 2 19648.12P2V
31.5 36.5 x98 3/C V1 I1 19647.16P#D 36.5x70 2 19648.16P2V
40 36.5 x98 3/C V1 I1 19647.20P#D 36.5x70 2 19648.20P2V
43 36.5 x98 3/C V1 I1 19647.23P#D 36.5x70 2 19648.23P2V
47 36.5 x98 3/C V1 I1 19647.27P#D 36.5x70 2 19648.27P2V
50 36.5 x98 3/C V1 I1 19647.30P#D 36.5x70 2 19648.30P2V
53 36.5 x98 3/C V1 I1 19647.33P#D 36.5x70 2 19648.33P2V
60 36.5 x98 3/C V1 I1 19647.40P#D 36.5x70 2 19648.40P2V
64 36.5 x98 3/C V1 I1 19647.44P#D 36.5x70 2 19648.44P2V
72 36.5 x98 3/C V1 I1 19647.52P#D 36.5x70 2 19648.52P2V
72 46 x98 4/D V1 I1 19647.52P#D
80 46 x98 4/D V1 I1 19647.60P#D 36.5x70 2 19648.60P2V
88 46 x98 4/D V1 I1 19647.68P#D 36.5x98 3/C 19648.68P#V
100 46 x98 4/D V1 I1 19647.80P#D 36.5x98 3/C 19648.80P#V
125 46 x124 5/E V1 I1 19647.C5P#D
156 46 x124 5/E V1 I1 19647.E6P#D
200 52 x124 6 C 19647.H0P6D
250 52 x124 6 C 19647.K0P6D
315 52 x124 6 C 19647.P5P6D
21 36.5 x70 2 C 19650.08P2D 36.5x70 2 19650.08P2V
31.5 36.5 x98 3/C C 19650.16P#D 36.5x70 2 19650.16P2V
43 46 x98 4/D C 19650.23P#D 36.5x70 2 19650.23P2V
47 46 x98 4/D C 19650.27P#D 36.5x70 2 19650.27P2V
53 46 x98 4/D C 19650.33P#D 36.5x70 2 19650.33P2V
64 46 x98 4/D C 19650.44P#D 36.5x70 2 19650.44P2V
72 46 x98 4/D C 19650.52P#D 36.5x70 2 19650.52P2V
80 46 x98 4/D C 19650.60P#D 36.5x70 2 19650.60P2V
88 46 x98 4/D C 19650.68P#D 36.5x98 3/C 19650.68P#V
100 46 x98 4/D C 19650.80P#D 36.5x98 3/C 19650.80P#V
125 46 x98 4/D C 19650.C5P#D
156 46 x124 5/E C 19650.E6P#D
200 52 x124 6 C 19650.H0P6D
250 52 x124 6 C 19650.K0P6D
315 52 x124 6 C 19650.P5P6D
16 36.5x70 2 C 19655.04P2D
21 36.5x70 2 V2 I2 19655.08P2D
21 36.5x98 3/C V2 I2 19655.08P#D
25 36.5x98 3/C V2 I2 19655.12P#D
30 36.5x98 3/C V2 I2 19655.15P#D
40 46x98 4/D V2 I2 19655.20P#D
43 46x98 4/D V2 I2 19655.23P#D
47 46x98 4/D V2 I2 19655.27P#D
50 46x98 4/D V2 I2 19655.30P#D
53 46x98 4/D V2 I2 19655.33P#D
64 46x98 4/D V2 I2 19655.44P#D
72 46x98 4/D V2 I2 19655.52P#D
72 46x124 5/E V2 I2 19655.52P#D
80 46x124 5/E V2 I2 19655.60P#D
88 46x124 5/E V2 I2 19655.68P#D
88 52x124 6 V2 I2 19655.68P6D
100 52x124 6 V2 I2 19655.80P6D
125 52x124 6 V2 I2 19655.C5P6D
156 52x124 6 V2 I2 19655.E6P6D
INDUSTRIAL APPLIANCE HOUSEHOLD APPLIANCES
V.ac
C
(µF)
D x L
(mm)
CASE
CODE
APPROVALS CODE
VDE IMQ C
ARTICLE
CODE
D X L
(mm)
CASE
CODE
ARTICLE
CODE
280
330
NOTE:# = CASE CODE; in order to complete the ARTICLE CODE put the case code up to your needs (With or without fixing stud)
in the last but one position. Ex.: 80
µ
F / 330 V.ac with fixing stud code = 19655.60PED
APPROVAL NOTE: For capacitors not included in the table but within the approved ranse 21 - 156 µF, PLS Inquire FACON.
250
16 36.5 x70 2 C 19647.04P2D 36.5x70 2 1964804.P2V
21 36.5 x70 2 V1 I1 19647.08P2D 36.5x70 2 19648.08P2V
21 36.5 x98 3/C V1 I1 19647.08P#D
Page 4
TABLE 3
FACON S.p.A. MANUFACTURING OF ELECTRICAL CAPACITORS
Via Molini Trotti, 13 - 21100 Varese - Italy - Tel. 39/(0)332/282300 - Telefax 39/(0)332/282705 - http://www.Facon.com
TECHNICAL CHARACTERISTICS
REFERENCE STANDARD EN60252-2; UPON REQUEST: UL/CSA RECOGNITION-EIA STANDARD TYPE 1-2
WORKING VOLTAGE V
N
rms voltage that can be applied to the motor-starting capacitor in
conformity with the specified duty cycle.
RATED FREQUENCY Hz 50÷60
CYCLE
CHARACTERISTICS
N
T
t
T+t
NT
T
T+t
Rated
duty cicle
%
time VNoff
startere rating/hour
relative operation time
Specified by the duty cycle duration (min)
and the relative operation time (%)
INDUSTRIAL APPLIANCES
TYPE
HOUSEHOLD
APPLIANCES
VDE - IMQ
PROD. APPROVED
PRODUCT WITHOUT APPROVALS
Vg 1.2 V
N
1.2 V
N
1.1 V
N
see table 2)
up to 260 Vac -10/ +60/ F= JUF (DIN 40040)
280÷330 Vac -10/ +55/ F=JVF (DIN40040)
- 10/ +55/ F =
=JVF (DIN40040)
% see table 2)
%7%
% 10%
-0 +20% ; ±10% on request
NOTE: Different cycles are possible with the limits of the indicated NT and T max.; for ex. (*):
NT= 60 could also represent N= 10 / T=6 or N=20 / T=3 etc
°C the max temperature in conformity with the specified climatic category.
±10%
POWER FACTOR: TYPICAL VALUE
MAX. VALUE
MAX. WORKING VOLTAGE
(1/10 max. of the start period)
CLIMATIC CATEGORY
CAPACITANCE TOLERANCE
STABILITY TEST:
8h. at 1.2 V
N
ACCORDING TO VDE 560-8
RAPID TEST:
6h. at V
N
8%
12%
10%
15%
°C ~ 50 °C
NT 30
> 500.000
~ 40 °C
30
> 100.000
~ 30 °C
30
> 100.000
100 h
100 h
EXPECTED LIFE:
No. OF STARTS UP
STORAGE TEST
at 85 °C
260 V.ac
70 (VDE)
60
6
10
590
1.7%
60
20
3 s
177 s
1.7%
60
20
3 s
177 s
1.7%
25 °C
120
60
2
58
3.3%
25 °C
120
60
2
58
3.3%
25 °C
60
30
2
118
1.7%
330 V.ac
55 (VDE)
60
10
6
354
1.7%
125÷330 V.ac
125÷280 V.ac
60° C
(*)60
6
10
590
1.7%
CYCLE CHARACTERISTICS
MAX START-UP TIME = S
V
N
°C
NT
N
T
t
T
T+t
%
NT
N
T
t
T
T+t
%
°C
NT
N
T
t
T
T+t
%
40° C
80
8
10
350
1.7%
40° C
40
10
4
356
1.1%
100 h
h
- Varese 03/07
time
V
Loading...