Datasheet SAA-101100, SAA-101200, SAA-102100, SAA-102200, SAA-111100 Datasheet (Epson)

DOCUMENT NUMBER NCD-5DC2-01

SAA-1 Series

Single-Mode

FC ADAPTOR

TECHNICAL SPECIFICATIONS

Seiko Instruments Inc.

Components Sales Dept.
8, Nakase 1-Chome
Mihama-ku, Chiba-shi, Chiba-ken
261 JAPAN
Telephone : [phone]

-1215

Facsimile : 043-211-8035

SAA-1 Series Single-Mode FC ADAPTOR
TECHNICAL SPECIFICATIONS

Document Number NCD-5DC2-01

NAE63D01 " SAA-1 Part " May 1986
NAE63D02 " SAA-1 Part " September 1986
SSA930305 March 1993
39055-2016-01 September 1993
NCD-5DC2-01 December 1995

Copyright 1986, 1993, 1995 by Seiko Instruments Inc.

All right reserved.

The information contained herein shall not reproduced or disclosed to any third party
without the express written consent of SII.
The Specifications contained herein are subject to change without notice.

SII is a trademark of Seiko Instruments Inc.

Please address any questions, comments, and suggestions to:

Seiko Instruments USA Inc.

Electronics Components Division
2990 West Lomita Boulevard
Torrance, CA 90505, U.S.A.
Phone: [phone]
Fax: [phone]

Seiko Instruments (H.K.) Ltd.

Sales Department
4th & 5th Floor, Wyler Center 2
200 Tai Lin Pai Road, Kwai Chung
N.T., Kowloon, Hong Kong
Phone: [phone]
Fax: [phone]

Seiko Instruments GmbH

OFC Division
Siemensstraße 9b
D-63263 Neu-Isenburg, Germany
Phone: [phone]
Fax: [phone]

Seiko Instruments Taiwan Inc.

Sales Department
5F-1, No.99, Sec. 2, Chung Shan
Rd.
Taipei 104, Taiwan, R.O.C.
Phone: [phone]
Fax: [phone]

Seiko Instruments Singapore pte. Ltd.

2, Marsiling Lane,
Woodlands New Town,
Singapore, 2573, Singapore
Phone: [phone]
Fax: [phone]

ii

TABLE OF CONTENTS

Section Page

1. PROVISION 1

1.1 Application Limit 1

2. PARTS NUMBER 1

3. GENERAL SPECIFICATIONS 2

3.1 Parts and Materials 2

3.2 Physical Dimensions 2

3.3 General Tolerances 2

3.4 Insertion Loss 3

4. PACKING 3

5. SHIPPING INSPECTION 3

Table

Table 1 Parts Number 1
Table 2 Parts and Materials 2
Table 3 General Tolerance 2
Table 4 Insertion Loss and the Measurement Conditions 3

Figure

Figure 1 Insertion Loss Measurement System 3
Figure 2 SAA-1 Adaptor 4
Figure 3 to 4 Part Dimensions 5

iii

iv

1. PROVISION

1.1 Application Limit
These specifications apply to the SAA-1 Single-Mode FC ADAPTOR supplied by SII.

2. PARTS NUMBER
Parts Number of the Adaptor is Shown in Table 1.

Table 1 Parts Number

1

3. GENERAL SPECIFICATIONS

3.1 Parts and Materials
Parts and the materials are shown in Table 2.

Table 2 Parts and materials

No. Part Name Q'ty Material Notes

Housing A 1 Brass Nickel Plating

①

Fitting Sleeve 2 Brass Nickel Plating

②

➂-1

Slit Sleeve 1

➂-2

Spacer 1 Brass Nickel Plating

➃

Housing B 1 Brass Nickel Plating

⑤

Screw 2 Brass Nickel Plating

➅

⑦-1

Cap 2

⑦-2

Phosphor Bronze
Zirconia Ceramics

Plastic White
Synthetic Rubber Red

--

3.2 Physical Dimensions
Figure 2 shows the SAA-1.
Figure 3 to 4 show the part dimension.

• In accordance with JIS C5970 F01 type connectors

3.3 General Tolerances
Permissible deviation in dimensions without tolerance indication is in accordance with
JIS B 0405 class m, as shown in Table 3.

Table 3 General tolerance (JIS B 0405 class m)

Basic size step (mm)

Over Under

0.5 3
36
630

30 120

Permissible deviation (mm)

±0.1
±0.1
±0.2
±0.3

2

3.4 Insertion Loss
Insertion Loss of the adaptor and the measurement conditions shown in Table 4.
Figure 1 shows the measurement system.

Measured Adaptor

Light-Source

Optical
Power Meter

Parts Number

Insertion Loss 0.7dB or Less 0.4dB or Less

Conditions

Master Cord

Master Plug

Master Plug

Master Cord

Photo Detector

Figure 1 Insertion loss measurement system

Table 4 Insertion loss and the measurement conditions

SAA-1 1❑❑00

( Slit Sleeve : Phosphor Bronze )

Light-Source LD or LED LD

Wavelength 1.3 µ m 1.3 µ m

Master Cord

Terminated

Flat Polishing with Buffing PC Polishing

( Slit Sleeve : Zirconia Ceramics )

SAA-1 2❑❑00

4. PACKING
The product is packed to prevent damage during shippment.

5. SHIPPING INSPECTION
The insertion loss inspected before shipping.

3

with Marking ( ROGO ) Type without Marking ( ROGO ) Type

FIgure 2 SAA-1

4

Unit : mm

Figure 3 ⑦-1 Cap

Figure 4 ⑦-2 Cap

Unit : mm

Unit : mm

5