Page 1
x
r
/
/
2
2
2
2
2
查询FDC05供应商查询FDC05供应商
• 5 WATTS OUTPUT POWER
• 2:1 AND 4:1 WIDE INPUT VOLTA GE RANGE
• INTERNATIONAL SAFETY STANDARD APPROVAL
• SIX-SIDED CONTINUOUS SHIELD
UL E193009
TUV R3-50007936
CB JPTUV-003641
CE MARK
• HIGH EFFICIENCY UP TO 83%
• STANDARD 2” X 1” X 0.4” PACKAGE
• FIXED SWITCHING FREQUENCY
The FDC05 and FDC05-W series offer 5 watts of output power from a 2 x 1 x 0.4 inch
package without derating to 71ºC ambient temperature. FDC05 series have 2:1 wide input
voltage of 9-18, 18-36 and 36-75VDC. FDC05-W series have 4:1 ultra wide input voltage of
9-36 and 18-75VDC. The FDC05 and FDC05-W features 1600VDC of isolation, short-circuit
protection, as well as six sided shielding. The safety approve with EN60950 and UL1950. All
models are particularly suited to telecommunications, industrial, mobile telecom and test
equipment applications. According the extended operation temperature range, there are
“M1” and “M2” version for special application.
TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25ºC otherw ise noted
OUTPUT SPEC IFICATIONS
Output power 5 Watts max
Voltage accuracy Full load and nominal Vin ± 2%
Minimum load (Note 1)
Line regulation LL to HL at Full Load
Load regulation
Cross regulation (Dual) Asymmetrical load 25% / 100% FL ± 5%
Ripple and noise 20MHz bandwidth 50mVp-p
Temperature coefficient
Transient response
recovery time
Over load protection % of FL at nominal input 170% typ
Short circuit protection Continuous, automatics recovery
10% to 100% FL Single
Dual
25% load step change
FL to 1/2 FL I1% error band
10% of FL
± 0.2%
± 0.2%
± 1%
I0.02% / ºC, max
Single 200uS
Dual 200uS
INPUT SPECIFICA TIONS
FDC05
Input voltage range
Input filter Pi type
Input surge voltage
100mS max
Input reflected ripple (Note 2) Nominal Vin and full load 20mAp-p
Start up time Nominal Vin and constant resistor load 600mS typ
Remote ON/OFF (Note 3)
(Positive logic)
(Negative logic)
Remote off input current
FDC05-W
12V nominal input
24V nominal input
48V nominal input
24V nominal input
48V nominal input
12V input
24V input
48V input
DC-DC ON
DC-DC OFF
DC-DC ON
DC-DC OFF
Nominal Vin
9 – 18VDC
18 – 36VDC
36 – 75VDC
9 – 36VDC
18 – 75VDC
36VDC
50VDC
100VDC
Open or 3.5V < Vr < 12V
Short or 0V < Vr < 1.2V
Short or 0V < Vr < 1.2V
Open or 3.5V < Vr < 12V
2.5mA
GENERAL SPECIFICATIONS
Efficiency See table
Isolation Voltage Input to Output to Case 1600VDC, min
Isolation resistance
Isolation capacitance 300pF, ma
Switching frequency
Approvals and standard IEC60950, UL1950, EN60950
Case material Nickel-coated coppe
Base material Non-conducted black plastic
Potting material Epoxy (UL94-V0)
Dimensions
Weight 27g (0.95oz)
MTBF (Note 4) 3.145 x 106 hrs
Standard
“W” series
2.00 X 1.00 X 0.40 Inch
(50.8 X 25.4 X 10.2 mm)
9
10
ohms, min
300KHz, typ
200KHz, typ
ENVIRONMENTAL SPECIFICATIONS
Operating temperature range
(Reference derating curve)
Maximum case temperature +100ºC
Storage temperature range -55ºC ~ +105ºC
Thermal impedance (Note 6)
Thermal shock MIL-STD-810D
Vibration 10~55Hz, 2G, 30minutes along X,Y and Z
Relative humidity 5% to 95% RH
Standard
M1 (Note 5)
M2 (W series)
Nature convection
Nature convection with heat-sink
-25ºC ~ +85ºC (with derating)
-40ºC ~ +85ºC (non-derating)
-40ºC ~ +85ºC (with derating)
12ºC
watt
watt
10ºC
EMC CHARACTER IS TI CS
Conducted emissions EN55022 Level A
Radiated emissions EN55022 Level A
ESD EN61000-4-2 Perf. Criteria
Radiated immunity EN61000-4-3 Perf. Criteria
Fast transient EN61000-4-4 Perf. Criteria
Surge EN61000-4-5 Perf. Criteria
Conducted immunity EN61000-4-6 Perf. Criteria
Page 2
(8)
V
)
A
(%)
t
ote5)
Model
Number
FDC05-12S33 9 – 18 VDC 3.3 VDC 1000mA
FDC05-12S05 9 – 18 VDC 5 VDC 1000mA
FDC05-12S12 9 – 18 VDC 12 VDC 470mA 610mA 81 290uF
FDC05-12S15 9 – 18 VDC 15 VDC 400mA 658mA 80 188uF
FDC05-12D05 9 – 18 VDC ± 5 VDC ± 500mA 595mA 74 ± 850uF
FDC05-12D12 9 – 18 VDC ± 12 VDC ± 230mA 597mA 81 ± 140uF
FDC05-12D15 9 – 18 VDC ± 15 VDC ± 190mA 609mA 82 ± 47uF
FDC05-24S33 (W) 18 – 36 (9 – 36) VDC 3.3 VDC 1000mA 199 (196mA) 73 (74) 3700uF
FDC05-24S05 (W) 18 – 36 (9 – 36) VDC 5 VDC 1000mA 282 (274mA) 78 (80) 1700uF
FDC05-24S12 (W) 18 – 36 (9 – 36) VDC 12 VDC 470mA 305 (301mA) 81 (82) 290uF
FDC05-24S15 (W) 18 – 36 (9 – 36) VDC 15 VDC 400mA 325 (325mA) 81 (81) 188uF
FDC05-24D05 (W) 18 – 36 (9 – 36) VDC ± 5 VDC ± 500mA 289 (289mA) 76 (76) ± 850uF
FDC05-24D12 (W) 18 – 36 (9 – 36) VDC ± 12 VDC ± 230mA 295 (295mA) 82 (82) ± 140uF
FDC05-24D15 (W) 18 – 36 (9 – 36) VDC ± 15 VDC ± 190mA 308 (301mA) 81 (83) ± 47uF
FDC05-48S33 (W) 36 – 75 (18 – 75) VDC 3.3 VDC 1000mA 100 (100m A ) 73 (73) 3700uF
FDC05-48S05 (W) 36 – 75 (18 – 75) VDC 5 VDC 1000mA 145 (149mA) 76 (74) 1700uF
FDC05-48S12 (W) 36 – 75 (18 – 75) VDC 12 VDC 470mA 151 (151mA) 82 (82) 290uF
FDC05-48S15 (W) 36 – 75 (18 – 75) VDC 15 VDC 400mA 160 (163mA) 82 (81) 188uF
FDC05-48D05 (W) 36 – 75 (18 – 75) VDC ± 5 VDC ± 500mA 149 (149mA) 74 (74) ± 850uF
FDC05-48D12 (W) 36 – 75 (18 – 75) VDC ± 12 VDC ± 230mA 149 (149mA) 81 (81) ± 140uF
FDC05-48D15 (W) 36 – 75 (18 – 75) VDC ± 15 VDC ± 190mA 154 (154mA) 81 (81) ± 47uF
Note
1. The FDC05 (W) series required a minimum 10% loading on the output to maintain specified
regulation. Operation under no-load condition will not damage these devices, however they may not
meet all listed specification
2. Simulated source impedance of 12uH. 12uH inductor on series with + Vin.
3. The ON/OFF control is option function. There are positive logic and negative logic. The pin voltage is
referenced to negative input
To order positive logic ON-OFF control add the suffix-P (Ex: FDC05-24S05-P)
To order negative logic ON-OFF control add the suffix-N (Ex: FDC05-24S05-N)
4. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC.
(Ground fixed and controlled environment)
5. M1 version is more efficient, therefore, it can be operated in a more extensive temperature range than
standard and M2 version.
6. Heat sink is optional and P/N: 7G-0020A.
7. Maximum value at nominal input voltage and full load of standard type.
8. Typical value at nominal input voltage and full load.
9. Test by minimum Vin and constant resistor load.
FDC05-48S05 Derating Curve
100
75
50
OUTPUT POWER (% )
100
OUTPUT POWER
Nature convection
25
0
AMBIENT T EMPERATURE (ºC )
FDC05-48S05 Derating Curve
Wi
h HEAT-SINK (N
75
50
25
0
MBIENT TEMPERATURE (ºC)
50 60 70 80 90
Nature convection
50 60 70 80 90
Input
Range
100 -40 -25 0 -10
100 -40 -25 0 -10
Output
Voltage
FDC05-48S05-M1 Derating Curve
100
75
50
25
OUTPUT POWER (%)
82
81
80
79
78
77
76
75
EFFICIENCY (%)
70
65
45
Nature convection
0
AMBIENT TEMPERATUR E (ºC)
FDC05-48S05
Efficiency VS Output load
OUTPUT LOAD (A
50 60 70 80 90
0.4 0.6 0.8 1.00.05 0.2
Output
Current
100-40 -25 0-10
Input
Current
387mA
556mA
(7)
Eff
(%)
75 3700uF
79 1700uF
PIN CONNECTION
PIN
1 + INPUT + INPUT
2 - INPUT - INPUT
3 + OUTPUT + OUTPUT
4 NO PIN
5 - OUTPUT - OUTPUT
6 CTRL (Option) CTRL (Option)
1.00(25.4)
0.40
(10.2)
0.50
(12.7)
0.40
(10.2)
SINGLE
34 5
Bottom
iew
2.00(50.8)
1 2
1. All dimensions in Inches (mm)
2. Pin Pitch tolerance I0.014(0.35)
6
0.10(2.5)
0.20(5.1)
0.80(20.3) 0.60(15.2)
Capacitor
Load max
DUAL OUTPUT
COMMON
0.40
(10.2)
DIA. 0.04(1. 0)
0.22(5.6)
(9)
Loading...