Datasheet cPCI200D-4, cPCI200D-3, cPCI200D-2, cPCI200D-1 Datasheet (CANDD)

Corporate: www.cdtechno.com

Corporate: www.cdtechno.com

Product: www.cdpoweronline.com

cPCI200DCcPCI200DC

cPCI200DC

cPCI200DCcPCI200DC

180/225 Watt, 3U x 4HP CompactPCI

zz

z 3U X 4HP

zz

zz

z 36-72 VDC Input Range

zz

zz

z

180/225 Watt Continuous Output

zz

Power

zz

z Complies with PICMG 2.11 R1.0 with

zz

47 Pin I/O Connector

zz

z Hot-Swap Capable

zz

The cPCI200DC is a family of high­reliability, 200 watt power supplies for
3U Compact PCI™ systems. Developed
to support hot-swap, redundant
operation, the cPCI200DC Series is
designed for compliance with PICMG™

2.11 R1.0 P ower Interface Specif ication
with 47-pin I/O connector. A vailable with
IPMI functionality (part numbers
cPCI200D-3 and cPCI200D-4) , this unit

zz

z Outputs Individually Protected

zz

Against Overloads; Automatic
Recovery

zz

z PCI VoltageArchitecture

zz

(5V, 3.3V,+12V,-12V)

zz

z

IPMI Capability (Available on Part

zz

Numbers cPCI200D-3 and 4)

(HA) telecommunications applications in
mind. Current sharing and internal ORing
diodes are included to support these and
other applications requiring reliable, hot­swap performance and N+1 redundant
configuration. The 4HP package and
complement of agency approvals provide
for an advanced, high-density, high­efficiency power solution for your
CompactPCI™ system requirements.

was developed with high-availability

SPECIFICATIONS, ALL MODELS

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Input Operating Voltage Vin 36 72 VDC
Input Voltage Withstand 34 75 VDC
Inrush Current I

INPUT

Efficiency η 48VDC input, full load 70 %

i

36VDC input < 20 APK
72VDC input < 40 APK

OUTPUT NUMBER RATED OUTPUT VOLTAGE Min A* B** REGULATION

V1 +5.0VDC 0A 18.0 A

V2 +3.3VDC 0A 27.0 A 27.0 A

V3 +12.0VDC 0A 4.0 A

V4 -12.0VDC 0A 4.0 A

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

OUTPUT

Temperature Coefficient T
PARD 20MHz bandwidth 50 mV

Output Power 50°C max temp., 300lfm airflow 180/225 W

Minimum Load V1 (config A, 180W) 500 mA

NOTES: Outputs share common return.

* Total output power not to exceed 180W.
** Total output power not to exceed 225W.
1 Maximum combined power not to exceed 90 Watts.

VOUT RATED OUTPUT CURRENTOUTPUT

C

all outputs or 1.5% P-P

V2 (config B, 225W) 500 mA

cPCI200-DC REV A 7/2003

IOUT

1

1

1

27.0 A +4 / -2%

1

1

4.0 A

1

4.0 A

0.02 %/°C

whichever is greater

+4 / -2%

+/-10%

+/-10%

P-P

SPECIFICATIONS, ALL MODELS

Transient Response

For a step load change of 50%-100%-50%, the peak output
excursion will not exceed 10% of nominal voltage, and will
recover to within 1% of nominal voltage within 500 microseconds.

Current Share

Active current sharing on Outputs V1and V2. Accuracy better than
10% of maximum rated load. Primary referenced.

an IPMI interface to the SM bus. Status functions include output
voltage and current levels as well as the DEG warning. Output
inhibit control can be toggled under software command. For a
complete specification of the firmware solution refer to
Application Note ACAN-02 on our website.

Power Fail Warning (FAL#)

Open collector signal indicates output failure. Active low.

Remote Sense

Outputs V1and V2 are capable of compensating >50mV of line
drop. Unit automatically reverts to local sensing in the event that
the sense leads are opened for any reason. Unit is protected against
reversed or shorted sense leads.

Output Power

180W (Output configuration A) / 225W (Output configuration
B) continuous maximum, with 300lfm airflow at a maximum
ambient of 50°C. Derate to 90W/110W at 70°C.

Overload Protection

Outputs are individually protected against overloads and
indefinite short circuit with automatic recovery upon removal of
the fault condition.

Over Voltage Protection

Outputs V1 and V2 have Over Voltage Protection a t 125% typical
(135% max.) of nominal.

Over Temperature Protection

Outputs are protected against over temperature. Outputs will
automatically restore upon recovery to acceptable temperatures.

Output Fault Isolation

Output isolation diodes are present in all outputs to isolate faults
within a failed power supply.

Remote Inhibit (INH#)

Secondary referenced, active low, TTL compatible signal inhibits
all outputs upon activation.

IPMI Option
Available on Models cPCI200D-3 and cPCI200D-4

2

C board is available as a factory-installed option to provide

An I

Enable (EN#)

Short pin on connector will enable power supply output when
the mating pin is grounded. Supply will not power up until this
pin is engaged to its mate in the backplane. Unit output will be
inhibited as pin is disengaged from the mating connector.

Temperature Warning (DEG#)

Open collector indicates internal temperatures are approaching
the thermal shutdown limit (+/-10°C, typ). Active low.

Fault Indicator LED

A red LED will be ON if output voltages are not within
specification.

Power Present LED

A green LED will be ON when input voltage is present and above
the minimum requirement.

Cooling

300lfm of airflow required to maintain full output power at 0­50°C ambient.

Temperature

Full output power achievable over the range of 0-50°C. Storage
temperature limits are –20 to +85°C.

Altitude

Operating: -200 to +10,000 feet with ambient temperature
derating above 5,000 feet in accordance with the adiabatic lapse
rate (approximately 2C per 1000 feet).

Inhibit Indicator LED (Yellow)

A yellow LED will be ON when the outputs are inhibited.

IPMI/IPMB POWER SUPPLY SATELLITE CONTROLLER FEATURES

AVAILABLE ON PART NUMBERS cPCI200D-3 AND cPCI200D-4

z Complies with IPMI V1.5 Rev 1.1 and IPMB V1.0
z Complies to PICMG 2.9 (CompactPCI Systems Manage-

ment Specification)

z 8 analog inputs configured for monitoring voltages and currents

on power supply outputs V1 - V4

z Monitors the state of the thermal sensor
z Output inhibit can be controlled by IPMI commands
z Self Test with LED indicator (can be read and overridden

by IPMI commands)

z 6 programmable thresholds on each analog sensor
z Each threshold on each sensor can be enabled to generate

event messages if that threshold is crossed

Product: www.cdpoweronline.com

cPCI200-DC REV A 7/2003

z Thermal sensor can be enabled to generate event messages
z Responds to all mandatory IPMI commands and numerous

optional commands as indicated in the functional specifi­cation

z Firmware can be upgraded via the IPMB bus
z Includes Device SDR’s (Sensor Data Records) - These

specify the type of sensor for each input (voltage, current,
temperature, etc.) as well as the conversion formulas from
raw ADC data to voltages, currents, etc.

z Includes FRU data such as model number, serial number

and firmware creation date

2

MECHANICAL

NOTES: All measurements are in inches.

PIN ASSIGNMENT: Pin assignment consistent with PICMG™ 2.11R1.0 specification. The table below details the PICMG™ assignment.

Pin # 1Staging

1-4 M V1 V1 Output
5-12 M RTN V1 and V2 Return
13-18 M V2 V2 Output
19 M RTN V3 Return
20 M V3 V3 Output
21 M V4 V4 Output
22 M RTN Signal Return
23 M RESERVED Reserved
24 M RTN V4 Return
25 M GA0 Geographic Address Bit 0
26 M RESERVED Reserved
27 S EN# Enable
28 M GA1 Geographic Address Bit 1
29 M V1ADJ V1 Adjust
30 M V1 SENSE V1 Remote Sense
31 M GA2 Geographic Address Bit 2
32 M V2ADJ V2 Adjust
33 M V2 SENSE V2 Remote Sense
34 M S RTN Sense Return
35 M V1 SHARE V1 Current Share
36 M V3 SENSE V3 Remote Sense
37 M IPMB SCL IPMB Serial Clock Line
38 M DEG# Degrade Signal
39 M INH# Inhibit
40 M IPMB SDA IPMB Serial Data Line
41 M V2 SHARE V2 Current Share
42 M FAL# Fail Signal
43 M IPMB PWR IPMB Power Input
44 M V3 SHARE V3 Current Share
45 L CGND Chassis Grnd (Safety Grnd)
46 M ACN/+DC IN AC Input Neutral/+DC Input
47 M ACL/-DC IN AC Input Line/-DC Input

NOTES: (1) Pin numbers correspond to the female backplane connector.

(2) L = Long Length Pin (First Make, Last Break); M = Medium

Length Pins; S = Short Length Pins (Last Make, First Break)

2

Signal Name Description

MECHANICAL

Shock: MIL-STD-810d, Method 516.3, Procedure 1.
Vibration: MIL-STD-810d, Method 514.3, Procedure 1.
Dimensions: 3U x 4HP x 160mm (see Mechanical above)

EMC & SAFETY

EMI: NEBS Compliant to GR1089 conducted emissions limit

ETSI Compliant to ETS 300-386 conducted emissions
limit

Safety Agency Ratings 180 Watt 225 Watt

Input Voltage: 36-72 VDC 36-72 VDC
Input Current: 7A 9A
Input Power: 260W 320W

Agency Approvals Pending

UL1950/CSA950, EN60950, CE Mark.
(Low Voltage Directive)

Weight: 1.4 lbs. (636g) net

Product: www.cdpoweronline.com

cPCI200-DC REV A 7/2003

3

ORDERING INFORMATION

PART NUMBER POWER +5V +3.3V +12V -12V IPMI

cPCI200D-4 225 W 27A 27A 4A 4A YES
cPCI200D-3 180 W 18A 27A 4A 4A YES
cPCI200D-2 225 W 27A 27A 4A 4A NO
cPCI200D-1 180 W 18A 27A 4A 4A NO

Power Electronics Division, Americas

3400 E Britannia Drive, Tucson, Arizona 85706

Tel: [phone] Fax: [phone]

Any data, prices, descriptions or specifications presented herein are subject to revision by C&D Technologies, Inc. without notice. While such information is believed to
be accurate as indicated herein, C&D Technologies, Inc. makes no warranty and hereby disclaims all warranties, express or implied, with regard to the accuracy or
completeness of such information. Further, because the product(s) featured herein may be used under conditions beyond its control, C&D Technologies, Inc. hereby
disclaims all warranties, either express or implied, concerning the fitness or suitability of such product(s) for any particular use or in any specific application or arising
from any course of dealing or usage of trade. The user is solely responsible for determining the suitability of the product(s) featured herein for user’s intended purpose
and in user’s specific application. C&D Technologies, Inc. does not warrant or recommend that any of its products be used in any life support or aviation or aerospace
applications.

Product: www.cdpoweronline.com

cPCI200-DC REV A 7/2003

C&D Technologies, EMEA/Asia Pacific

Tel: [phone] Fax: [phone]

Milton Keynes MK14 5BU UK

4