Datadelay PDU15F-0.5, PDU15F-0.5A4, PDU15F-0.5B4, PDU15F-0.5M, PDU15F-0.5MC4 Datasheet

PDU15F

Doc #97003 DATA DELAY DEVICES, INC. 1

1/13/97 3 Mt. Prospect Ave. Clifton, NJ 07013

5-BIT PROGRAMMABLE
DELAY LINE
(SERIES PDU15F)

FEATURES PACKAGES

• Digitally programmable in 32 delay steps

• Monotonic delay-versus-address variation

• Two separate outputs: inverting & non-inverting

• Precise and stable delays

• Input & outputs fully TTL interfaced & buffered

• 10 T2L fan-out capability

• Fits standard 24-pin DIP socket

• Auto-insertable

FUNCTIONAL DESCRIPTION

The PDU15F-series device is a 5-bit digitally programmable delay line.
The delay, TDA, from the input pin (IN) to the output pins (OUT, OUT/)
depends on the address code (A4-A0) according to the following formula:

TDA = TD0 + T

INC

* A

where A is the address code, T

INC

is the incremental delay of the device,
and TD0 is the inherent delay of the device. The incremental delay is
specified by the dash number of the device and can range from 0.5ns through 20ns, inclusively. The
enable pins (EN/) are held LOW during normal operation. These pins must always be in the same state
and may be tied together externally. When these signals are brought HIGH, OUT and OUT/ are forced
into LOW and HIGH states, respectively. The address is not latched and must remain asserted during
normal operation.

SERIES SPECIFICATIONS

• Total programmed delay tolerance: 5% or 1ns,

whichever is greater

• Inherent delay (TD0): 9ns typical (OUT)

8ns typical (OUT/)

• Setup time and propagation delay:

Address to input setup (T

AIS

): 5ns

Disable to output delay (T

DISO

): 6ns typ. (OUT)

• Operating temperature: 0° to 70° C

• Temperature coefficient: 100PPM/°C (excludes TD0)

• Supply voltage VCC: 5VDC ± 5%

• Supply current: I

CCH

= 74ma

I

CCL

= 30ma

• Minimum pulse width: 10% of total delay

1997 Data Delay Devices

data

delay
devices, inc.



3

24
23
22
21
20
19
18
17
16
15
14
13

1
2
3
4
5
6
7
8
9
10
11
12

OUT/

OUT

EN/

GND

N/C

IN

N/C

GND

N/C
N/C

EN/

GND

VCC
A0
A1
A2
VCC
N/C
N/C
N/C
VCC
A3
A4
N/C

PDU15F-xx

DIP

PDU15F-xxA4

Gull-Wing

PDU15F-xxB4

J-Lead

PDU15F-xxM

Military DIP

PDU15F-xxMC4

Military Gull-Wing

PIN DESCRIPTIONS

IN Delay Line Input
OUT Non-inverted Output
OUT/ Inverted Output
A0-A4 Address Bits
EN/ Output Enable
VCC +5 Volts
GND Ground

DASH NUMBER SPECIFICATIONS

Part

Number

Incremental Delay

Per Step (ns)

Total Delay

Change (ns)

PDU15F-.5

.5 ± .3 15.5 ± 1.0

PDU15F-1

1 ± .5 31 ± 1.6

PDU15F-2

2 ± .5 62 ± 3.1

PDU15F-3

3 ± 1.0 93 ± 4.7

PDU15F-4

4 ± 1.0 124 ± 6.2

PDU15F-5

5 ± 1.0 155 ± 7.8

PDU15F-6

6 ± 1.0 186 ± 9.3

PDU15F-8

8 ± 1.0 248 ± 12.4

PDU15F-10

10 ± 1.5 310 ± 15.5

PDU15F-12

12 ± 1.5 372 ± 18.6

PDU15F-15

15 ± 1.5 465 ± 23.3

PDU15F-20

20 ± 2.0 620 ± 31.0

NOTE: Any dash number between .5 and 20 not

shown is also available.

PDU15F

Doc #97003 DATA DELAY DEVICES, INC. 2

1/13/97 Tel: [phone] Fax: [phone] http://www.datadelay.com

APPLICATION NOTES

ADDRESS UPDATE

The PDU15F is a memory device. As such,
special precautions must be taken when
changing the delay address in order to prevent
spurious output signals. The timing restrictions
are shown in Figure 1.

After the last signal edge to be delayed has
appeared on the OUT pin, a minimum time,
T

OAX

, is required before the address lines can
change. This time is given by the following
relation:

T

OAX

= max { (Ai - A

i-1

) * T

INC

, 0 }

where A

i-1

and Ai are the old and new address
codes, respectively. Violation of this constraint
may, depending on the history of the input signal,
cause spurious signals to appear on the OUT
pin. The possibility of spurious signals persists
until the required T

OAX

has elapsed.

A similar situation occurs when using the EN/
signal to disable the output while IN is active. In
this case, the unit must be held in the disabled
state until the device is able to “clear” itself. This
is achieved by holding the EN/ signal high and
the IN signal low for a time given by:

T

DISH

= Ai * T

INC

Violation of this constraint may, depending on
the history of the input signal, cause spurious
signals to appear on the OUT pin. The

possibility of spurious signals persists until the
required T

DISH

has elapsed.

INPUT RESTRICTIONS

There are three types of restrictions on input
pulse width and period listed in the AC
Characteristics table. The recommended
conditions are those for which the delay
tolerance specifications and monotonicity are
guaranteed. The suggested conditions are
those for which signals will propagate through the
unit without significant distortion. The absolute
conditions are those for which the unit will
produce some type of output for a given input.

When operating the unit between the
recommended and absolute conditions, the
delays may deviate from their values at low
frequency. However, these deviations will
remain constant from pulse to pulse if the input
pulse width and period remain fixed. In other
words, the delay of the unit exhibits frequency
and pulse width dependence when operated
beyond the recommended conditions. Please
consult the technical staff at Data Delay Devices
if your application has specific high-frequency
requirements.

Please note that the increment tolerances listed
represent a design goal. Although most delay
increments will fall within tolerance, they are not
guaranteed throughout the address range of the
unit. Monotonicity is, however, guaranteed over
all addresses.

T

DISO

T

OAX

T

AENS

T

ENIS

PW

IN

TD

A

PW

OUT

T

DISH

A4-A0

EN/

IN

OUT

OUT/

Figure 1: Timing Diagram

A

i-1

A

i

T

SKEW

T

AIS