Danfoss AMV 01, AMV 02, AMV-H 01, AMV-H 02 Data sheet [nl]

Data sheet

Actuators for three point control
AMV 01, AMV 02, AMV-H 01, AMV-H 02

Description AMV 01/02 and AMV-H 01/02 actuators are used

with VZ, VZL, VRBZ or with AB-QM valves (AMV
version only). The actuator can be used with
fan coil units, induction units, small reheaters,
recoolers, and zone applications in which hot/
cold water is the controlled medium.

Main data:

• 3-point versions

• The advanced design incorporates no-force

switch-off at stem up position, which enables

AMV 01, AMV 02

use of the actuator on valves with different
nominal strokes and improves the controller
response

• Force switch-off at stem down position

prevents overload of actuator and valve

• No tools required for mounting

• Maintenance free during the lifetime

• Low noise operation

• Supplied with 1.5 m cable.

Ordering

Technical data

AMV-H 01, AMV-H 02

Type

AMV 01

AMV 02 12 s/mm 082H8004

AMV-H 01 24 s/mm 082H8021

AMV-H 02 12 s/mm 082H8024

AMV 01

AMV 02 12 s/mm 082H8005

AMV-H 01 24 s/mm 082H8022

AMV-H 02 12 s/mm 082H8025

Type AMV 01, AMV-H 01 AMV 02, AMV-H 02

Power supply 24 Vac, 230 Vac; +10 to –15%

Power consumption 1 VA - 24 Vac; 7 VA-230 Vac

Frequency 50 Hz/60 Hz

Close of force 200 N

Max. stroke 5.5 mm

Speed 24 s/mm 12 s/mm

Max. medium temperature inside the pipe 120 °C

Ambient temperature 0 to 55 °C

Storage and transport temperature –40 to +70 °C

Protection code IP 42

Weight 0.34 kg

Supply

voltage

24 V~

230 V~

- marking in accordance with standards

Speed Code No.

24 s/mm 082H8001

24 s/mm 082H8002

Spare parts

Type Code No.

1.5 m cable for AMV, AMV-H - 24 V 082H8007

1.5 m cable for AMV, AMV-H - 230 V 082H8008

EMC- Directive 89/336/EEC, 92/31/EEC, 93/68/EEC,
EN 50081-1 and EN 50082-1
Low voltage Directive 73/23/EEC and 93/68/EEC,
EN 60730/2/14

SIBC VD.JC.M2.02 © Danfoss 08/05 1

Data sheet Actuators for three point control AMV 01, AMV 02, AMV-H 01, AMV-H 02

Installation Mechanical

The actuator should be mounted with the valve
stem in either horizontal position or pointing
upwards.

The actuator is fixed to the valve body by means
of a mounting ring which requires no tools for
mounting. The ring should be tightened by hand.

Electrical

Important: It is strongly recommended that the
mechanical installation is completed before the
electrical installation.

Each actuator is supplied with the connecting
cable for the controller.

Wiring

AMV/AMV-H 01, AMV/AMV-H 02 - 24V

AMV/AMV-H 01, AMV/AMV-H 02 - 230V

Disposal The actuator must be dismantled and the

elements sorted into various material groups
before disposal.

Commissioning All actuators are factory tested prior to shipment.

The factory setting of the spindle is the fully
stem up position because of easier mechanical
connection of actuator on valve.

Important: Uninstalled actuator will operated
properly only in stem down direction!

If uninstalled actuator is tested than use Allen key
size 4 mm (or knob for AMV-H version) in order to
drive actuator on it's top position.

2 VD.JC.M2.02 © Danfoss 08/05 SIBC