Daikin FDM20JEVLK, RD20JEVLK, FDM25JEVLK, RD25JEVLK, FDM30JEVLK Installation manuals

INSTALLATION
MANUAL

R22 SPLIT SERIES

MODELS
FDM20JEVLK RD20JEVLK

FDM25JEVLK RD25JEVLK
FDM30JEVLK RD30JEVLK
FDM40JEVLK RD40JEVLK
FDM50JEVLK RD50JETLK
FDM60JEVLK RD60JETLK
FDYM20JEVLK RYD20JEVLK
FDYM25JEVLK RYD25JEVLK
FDYM30JEVLK RYD30JEVLK

Installation Manual

R22 Split Series

English

FDYM40JEVLK RYD40JEVLK
FDYM50JEVLK RYD50JETLK
FDYM60JEVLK RYD60JETLK

IM-CCC/E-0311(0)-DAIKIN (SASO)

Part No.: R08019036182

Indoor Unit

OUTLINE AND DIMENSIONS

All dimensions are in mm

I
J

K

L

Model

H

Dimension

B

D
C

O

E

A

MN G

F

ABCDE FGHI J KLMNO

FD(Y)M20JEVLK 31 1041 1002 962 10 1065 72 261 411 351 225 211 232 213 114

FD(Y)M25JEVLK 31 1176 1137 1097 10 1200 72 261 411 351 225 211 232 213 114

English

Original Instruction

Indoor Unit

Dimension

Model
FD(Y)M30JEVLK

FD(Y)M40JEVLK

K

J

I

H

B

A

DE

C

G

F

P

All dimensions are in mm

L

M

N

O

AB C D E FG H I J K LMNOP

40 292 1295 232 213 70 128 1228 1185 284 1262 460 420 241 12 230

1-1

Indoor Unit

All dimensions are in mm

J

Model

Dimension

EE

AAK

B

C

D

L

MN

K

G

H

I

F

ABCDE FGHI JKLMN

FD(Y)M50JEVLK 359 1369 1326 1287 594 384 541 256 173 306 256 161 248 220
FD(Y)M60JEVLK 359 1569 1526 1487 694 378 541 256 173 306 356 161 248 220

Outdoor Unit

Model

Dimension

L

O

PBQ

ABCDE FGHI J KLMNOPQRS T

KL

M

A

D

All dimensions are in mm

N

TN

C

F

E

S

R

HG

IJ

R(Y)D20JEVLK 855 628 328 508 181 44 93 149 101 113 603 126 164 15 49 3 23 73 75 362
R(Y)D25JEVLK 855 730 328 520 182 44 93 149 101 113 603 126 164 15 34 3 23 73 75 362
R(Y)D30JEVLK 855 730 328 513 182 44 93 149 101 113 603 126 164 15 47 3 23 73 75 362

1-2

Outdoor Unit

All dimensions are in mm

Dimension

Model
R(Y)D40JEVLK

R(Y)D50JETLK
R(Y)D60JETLK

N

K

D

B

F

E

A

M

P

L

T

R

G

S

U

Q

C

H

J

AB C D E FGH J K LMN PQ R S TU

1030 852 428 410 412 827 72 196 91 488 448 142 141 83 23 49 26 28 80

English

1-3

INSTALLATION MANUAL

This manual provides the procedures of installation to ensure a safe and good standard of operation for the air
conditioner unit.
Special adjustment may be necessary to suit local requirements.
Before using your air conditioner, please read this instruction manual carefully and keep it for future reference.
This appliance is intended to be used by expert or trained users in shops, in light industry and on farms, or for
commercial use by lay persons.

SAFETY PRECAUTIONS

! WARNING ! CAUTION

• Installation and maintenance should be performed by
qualiÀ ed persons who are familiar with local code and
regulation, and experienced with this type of appliance.

• All À eld wiring must be installed in accordance with the
national wiring regulation.

• Ensure that the rated voltage of the unit corresponds to
that of the name plate before commencing wiring work
according to the wiring diagram.

• The unit must be GROUNDED to prevent possible hazard
due to insulation failure.

• All electrical wiring must not touch the refrigerant piping,
or any moving parts of the fan motors.

• ConÀ rm that the unit has been switched OFF before
installing or servicing the unit.

• Disconnect from the main power supply before servicing
the air conditioner unit.

• DO NOT pull out the power cord when the power is ON.
This may cause serious electrical shocks which may result
in À re hazards.

• Keep the indoor and outdoor units, power cable and
transmission wiring, at least 1m from TVs and radios,
to prevent distorted pictures and static. (Depending on
the type and source of the electrical waves, static may be
heard even when more than 1m away).

Please take note of the following important points when
installing.

• Do not install the unit where leakage of Á ammable gas
may occur.

If gas leaks and accumulates around the unit, it may

cause À re ignition.

• Ensure that drainage piping is connected properly.

If the drainage piping is not connected properly, it may

cause water leakage which will dampen the furniture.

• Do not overcharge the unit.

This unit is factory pre-charged.
Overcharge will cause over-current or damage to the

compressor.

• Ensure that the unit·s panel is closed after service or

installation.

Unsecured panels will cause the unit to operate

noisily.

• Sharp edges and coil surfaces are potential locations

which may cause injury hazards.

Avoid from being in contact with these places.

• Before turning off the power supply, set the remote
controller·s ON/OFF switch to the “OFF” position to
prevent the nuisance tripping of the unit. If this is not

done, the unit·s fans will start turning automatically when
power resumes, posing a hazard to service personnel or the
user.

• Do not install the units at or near doorway.

• Do not operate any heating apparatus too close to the

air conditioner unit or use in room where mineral oil, oil
vapour or oil steam exist, this may cause plastic part to
melt or deform as a result of excessive heat or chemical
reaction.

• When the unit is used in kitchen, keep Á our away from
going into suction of the unit.

• This unit is not suitable for factory used where cutting oil
mist or iron powder exist or voltage Á uctuates greatly.

• Do not install the units at area like hot spring or oil
reÀ nery plant where sulphide gas exists.

• Ensure the color of wires of the outdoor unit and the
terminal markings are same to the indoors respectively.

• IMPORTANT: DO NOT INSTALL OR USE THE AIR
CONDITIONER UNIT IN A LAUNDRY ROOM.

• Don·t use joined and twisted wires for incoming power
supply.

• The equipment is not intended for use in a potentially
explosive atmosphere.

Disposal requirements

NOTICE

Your air conditioning product is marked with this symbol. This means that electrical and electronic products
shall not be mixed with unsorted household waste.
Do not try to dismantle the system yourself: the dismantling of the air conditioning system, treatment of the
refrigerant, of oil and of other parts must be done by a qualiÀ ed installer in accordance with relevant local and
national legislation.
Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By
ensuring this product is disposed of correctly, you will help to prevent potential negative consequences for the
environment and human health. Please contact the installer or local authority for more information.
Batteries must be removed from the remote controller and disposed of separately in accordance with relevant
local and national legislation.

1-4

IMPORTANT & SEQUENCE AS FOLLOW:

For model FD(Y)M20JEVLK & FD(Y)M25JEVLK:

2) Left Cushion

4) Indoor Unit

1) Carton Box

UNPACKING

1) After take off the bands, lift the unit out from the carton box

2) Remove the right and left cushion.

English

3) Right Cushion

For model FD(Y)M30JEVLK & FD(Y)M40JEVLK:

1) Carton Box

3) Indoor Unit

2) Top Carton

UNPACKING

1) After take off the bands, lift the carton box

2) Remove the top cushion.

3) Lift the unit and remove the bottom carton.

4) Bottom Carton

1-5

For model FR(Y)M50JEVLK & FD(Y)M60JEVLK:

1) Carton Box

2) Top Cushion

3) Indoor Unit

4) Packing bottom

UNPACKING

1) After take off the bands, lift the carton box

2) Remove the top cushion.

3) Lift the unit and remove the bottom carton.

For model R(Y)D20JEVLK, R(Y)D25JEVLK, R(Y)D30JEVLK, R(Y)D40JEVLK, R(Y)D50JETLK &
R(Y)D60JETLK:

1. After take off the bands, pull out the carton box from the top side of the unit.

* This product is not designed for re-packing. In case of re-packing, contact to Daikin Dealer.

1-6

INSTALLATION DIAGRAM

Indoor unit

Hanger

Supply Duct

Air Intake

Drain Piping

English

Return Duct

Wrap the insulated pipe with the
À nishing tape from bottom to top

Thermal Insulation

Air Intake

Air Discharge

Outdoor unit

1-7