Daikin EHVH04SU18CB6W, EHVH08SU18CB6W, EHVH08SU26CB6W, EHVH11SU26CB6W, EHVH16SU26CB6W Installation manuals

Installation manual

Daikin Altherma – Low temperature split

EHVH04SU18CB6W EHVH08SU18CB6W EHVH08SU26CB6W EHVH11SU26CB6W EHVH16SU26CB6W

Installation manual

Daikin Altherma – Low temperature split

English

Directivelor, cu amendamentele respective.

<A>

<C>

DEKRA (NB0344)

2082543.0551-QUA/EMC

DAIKIN.TCF.025H22/10-2016

Direktive z vsemi spremembami.

Direktiivid koos muudatustega.

Директиви, с техните изменения.

Direktyvose su papildymais.

Direktīvās un to papildinājumos.

Smernice, v platnom znení.

18192021222324

Direktiver, med senere ændringer.

Direktiv, med företagna ändringar.

Direktiver, med foretatte endringer.

10111213141516

Directives, as amended.

Direktiven, gemäß Änderung.

deklaruje na własną i wyłączną odpowiedzialność, że urządzenia, których ta deklaracja dotyczy:

declară pe proprie răspundere că echipamentele la care se referă această declaraţie:

z vso odgovornostjo izjavlja, da je oprema naprav, na katero se izjava nanaša:

kinnitab oma täielikul vastutusel, et käesoleva deklaratsiooni alla kuuluv varustus:

декларира на своя отговорност, че оборудването, за коeто се отнася тази декларация:

visiška savo atsakomybe skelbia, kad įranga, kuriai taikoma ši deklaracija:

ar pilnu atbildību apliecina, ka tālāk aprakstītās iekārtas, uz kurām attiecas šī deklarācija:

vyhlasuje na vlastnú zodpovednosť, že zariadenie, na ktoré sa vzťahuje toto vyhlásenie:

tamamen kendi sorumluluǧunda olmak üzere bu bildirinin ilgili olduǧu donanımının aşaǧıdaki gibi olduǧunu beyan eder:

17

18

19

20

21

22

23

24

25

megfelelnek az alábbi szabvány(ok)nak vagy egyéb irányadó dokumentum(ok)nak, ha azokat előírás szerint használják:

spełniają wymogi następujących norm i innych dokumentów normalizacyjnych, pod warunkiem że używane są zgodnie z naszymi instrukcjami:

sunt în conformitate cu următorul (următoarele) standard(e) sau alt(e) document(e) normativ(e), cu condiţia ca acestea să fie utilizate în conformitate cu

instrucţiunile noastre:

skladni z naslednjimi standardi in drugimi normativi, pod pogojem, da se uporabljajo v skladu z našimi navodili:

on vastavuses järgmis(t)e standardi(te)ga või teiste normatiivsete dokumentidega, kui neid kasutatakse vastavalt meie juhenditele:

съответстват на следните стандарти или други нормативни документи, при условие, че се използват съгласно нашите инструкции:

atitinka žemiau nurodytus standartus ir (arba) kitus norminius dokumentus su sąlyga, kad yra naudojami pagal mūsų nurodymus:

tad, ja lietoti atbilstoši ražotāja norādījumiem, atbilst sekojošiem standartiem un citiem normatīviem dokumentiem:

sú v zhode s nasledovnou(ými) normou(ami) alebo iným(i) normatívnym(i) dokumentom(ami), za predpokladu, že sa používajú v súlade snašim

návodom:

161718192021222324

ürünün, talimatlarımıza göre kullanılması koşuluyla aşağıdaki standartlar ve norm belirten belgelerle uyumludur:

Directives, telles que modifiées.

010203040506070809

Değiştirilmiş halleriyle Yönetmelikler.

Direktiivejä, sellaisina kuin ne ovat muutettuina.

v platném znění.

Smjernice, kako je izmijenjeno.

irányelv(ek) és módosításaik rendelkezéseit.

z późniejszymi poprawkami.

Richtlijnen, zoals geamendeerd.

Directivas, según lo enmendado.

Direttive, come da modifica.

Οδηγιών, όπως έχουν τροποποιηθεί.

Directivas, conforme alteração em.

както е изложено в <A> и оценено положително от

съгласно Сертификата<C>.

kaip nustatyta <A> ir kaip teigiamai nuspręsta pagal

Sertifikatą<C>.

kā norādīts <A> un atbilstoši pozitīvajam vērtējumam

saskaņā ar sertifikātu<C>.

ako bolo uvedené v <A> a pozitívne zistené vsúlade

s osvedčením<C>.

<A>’da belirtildiği gibi ve <C>Sertifikasına göre

tarafından olumlu olarak değerlendirildiği gibi.

Директив со всеми поправками.

21Забележка*

22Pastaba*

23Piezīmes*

24Poznámka*

25Not*

a(z) <A> alapján, a(z) igazolta a megfelelést, a(z)

<C>tanúsítvány szerint.

zgodnie z dokumentacją <A>, pozytywną

opinią i Świadectwem<C>.

aşa cum este stabilit în <A> şi apreciat pozitiv de

în conformitate cu Certificatul<C>.

kot je določeno v <A> in odobreno s strani

vskladu scertifikatom<C>.

nagu on näidatud dokumendis <A> ja heaks kiidetud

järgi vastavalt sertifikaadile<C>.

16Megjegyzés*

17Uwaga*

18Notă*

19Opomba*

20Märkus*

Low Voltage 2014/35/EU

enligt <A> och godkänts av enligt

Certifikatet<C>.

som det fremkommer i <A> og gjennom positiv

bedømmelse av ifølge Sertifikat<C>.

jotka on esitetty asiakirjassa <A> ja jotka

on hyväksynyt Sertifikaatin<C> mukaisesti.

jak bylo uvedeno v <A> a pozitivně zjištěno

vsouladu sosvědčením<C>.

kako je izloženo u <A> i pozitivno ocijenjeno odstrane

Electromagnetic Compatibility 2014/30/EU *

заявляет, исключительно под свою ответственность, что оборудование, к которому относится настоящее заявление:

erklærer under eneansvarlig, at udstyret, som er omfattet af denne erklæring:

deklarerar i egenskap av huvudansvarig, att utrustningen som berörs av denna deklaration innebär att:

erklærer et fullstendig ansvar for at det utstyr som berøres av denne deklarasjon innebærer at:

ilmoittaa yksinomaan omalla vastuullaan, että tämän ilmoituksen tarkoittamat laitteet:

prohlašuje ve své plné odpovědnosti, že zařízení, k němuž se toto prohlášení vztahuje:

izjavljuje pod isključivo vlastitom odgovornošću da oprema na koju se ova izjava odnosi:

teljes felelőssége tudatában kijelenti, hogy a berendezések, melyekre e nyilatkozat vonatkozik:

09

10

11

12

13

14

15

16

estão em conformidade com a(s) seguinte(s) norma(s) ou outro(s) documento(s) normativo(s), desde que estes sejam utilizados de

acordo com as nossas instruções:

соответствуют следующим стандартам или другим нормативным документам, при условии их использования согласно нашим инструкциям:

overholder følgende standard(er) eller andet/andre retningsgivende dokument(er), forudsat at disse anvendes i henhold til vore instrukser:

respektive utrustning är utförd i överensstämmelse med och följer följande standard(er) eller andra normgivande dokument, under förutsättning att

användning sker i överensstämmelse med våra instruktioner:

respektive utstyr er i overensstemmelse med følgende standard(er) eller andre normgivende dokument(er), under forutssetning av at disse brukes i

henhold til våre instrukser:

vastaavat seuraavien standardien ja muiden ohjeellisten dokumenttien vaatimuksia edellyttäen, että niitä käytetään ohjeidemme mukaisesti:

za předpokladu, že jsou využívány v souladu s našimi pokyny, odpovídají následujícím normám nebo normativním dokumentům:

08091011121314

u skladu sa slijedećim standardom(ima) ili drugim normativnim dokumentom(ima), uz uvjet da se oni koriste u skladu s našim uputama:

ob upoštevanju določb:

vastavalt nõuetele:

следвайки клаузите на:

laikantis nuostatų, pateikiamų:

ievērojot prasības, kas noteiktas:

19202122232425

održiavajúc ustanovenia:

11Information*

12Merk*

13Huom*

bunun koşullarına uygun olarak:

delineato nel <A> e giudicato positivamente da

secondo il Certificato<C>.

όπως καθορίζεται στο <A> και κρίνεται θετικά

από το σύμφωνα με το Πιστοποιητικό<C>.

tal como estabelecido em <A> e com o parecer positivo

prema Certifikatu<C>.

14Poznámka*

15Napomena*

de de acordo com o Certificado<C>.

как указано в <A> и в соответствии сположительным

решением согласно Свидетельству<C>.

som anført i <A> og positivt vurderet af ihenhold til

Certifikat<C>.

Shigeki Morita

Director

Ostend, 3rd of October 2016

declares under its sole responsibility that the equipment to which this declaration relates:

erklärt auf seine alleinige Verantwortung daß die Ausrüstung für die diese Erklärung bestimmt ist:

déclare sous sa seule responsabilité que l'équipement visé par la présente déclaration:

CE - DECLARATION-OF-CONFORMITY CE - DECLARACION-DE-CONFORMIDAD CE - DECLARAÇÃO-DE-CONFORMIDADE CE - ERKLÆRING OM-SAMSVAR CE - IZJAVA-O-USKLAĐENOSTI CE - IZJAVA O SKLADNOSTI CE - ATITIKTIES-DEKLARACIJA

CE - KONFORMITÄTSERKLÄRUNG CE - DICHIARAZIONE-DI-CONFORMITA CE - ЗАЯВЛЕНИЕ-О-СООТВЕТСТВИИ CE - ILMOITUS-YHDENMUKAISUUDESTA CE - MEGFELELŐSÉGI-NYILATKOZAT CE - VASTAVUSDEKLARATSIOON CE - ATBILSTĪBAS-DEKLARĀCIJA

CE - DECLARATION-DE-CONFORMITE CE - ΔHΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ CE - OVERENSSTEMMELSESERKLÆRING CE - PROHLÁŠENÍ-O-SHODĚ CE - DEKLARACJA-ZGODNOŚCI CE - ДЕКЛАРАЦИЯ-ЗА-СЪОТВЕТСТВИЕ CE - VYHLÁSENIE-ZHODY

CE - CONFORMITEITSVERKLARING CE - FÖRSÄKRAN-OM-ÖVERENSTÄMMELSE CE - DECLARAŢIE-DE-CONFORMITATE CE - UYGUNLUK-BEYANI

verklaart hierbij op eigen exclusieve verantwoordelijkheid dat de apparatuur waarop deze verklaring betrekking heeft:

Daikin Europe N.V.

03

06Nota*

under iagttagelse af bestemmelserne i:

enligt villkoren i:

gitt i henhold til bestemmelsene i:

noudattaen määräyksiä:

za dodržení ustanovení předpisu:

prema odredbama:

követi a(z):

zgodnie z postanowieniami Dyrektyw:

101112131415161718

declara bajo su única responsabilidad que el equipo al que hace referencia la declaración:

dichiara sotto la propria responsabilità che gli apparecchi a cui è riferita questa dichiarazione:

δηλώνει με αποκλειστική της ευθύνη ότι ο εξοπλισμός στον οποίο αναφέρεται η παρούσα δήλωση:

declara sob sua exclusiva responsabilidade que os equipamentos a que esta declaração se refere:

06

EHVH04SU18CB6W, EHVH08SU18CB6W, EHVH08SU26CB6W, EHVH11SU26CB6W, EHVH16SU26CB6W,

07

are in conformity with the following standard(s) or other normative document(s), provided that these are used in accordance with our instructions:

der/den folgenden Norm(en) oder einem anderen Normdokument oder -dokumenten entspricht/entsprechen, unter der Voraussetzung, daß sie gemäß

unseren Anweisungen eingesetzt werden:

sont conformes à la/aux norme(s) ou autre(s) document(s) normatif(s), pour autant qu'ils soient utilisés conformément à nos instructions:

conform de volgende norm(en) of één of meer andere bindende documenten zijn, op voorwaarde dat ze worden gebruikt overeenkomstig onze

instructies:

están en conformidad con la(s) siguiente(s) norma(s) u otro(s) documento(s) normativo(s), siempre que sean utilizados de acuerdo con nuestras

instrucciones:

sono conformi al(i) seguente(i) standard(s) o altro(i) documento(i) a carattere normativo, a patto che vengano usati in conformità alle nostre istruzioni:

είναι σύμφωνα με το(α) ακόλουθο(α) πρότυπο(α) ή άλλο έγγραφο(α) κανονισμών, υπό την προϋπόθεση ότι χρησιμοποιούνται

01020304050607

σύμφωνα με τις οδηγίες μας:

following the provisions of:

gemäß den Vorschriften der:

conformément aux stipulations des:

EN60335-2-40,

overeenkomstig de bepalingen van:

010203040506070809

în urma prevederilor:

as set out in <A> and judged positively by

siguiendo las disposiciones de:

secondo le prescrizioni per:

με τήρηση των διατάξεων των:

de acordo com o previsto em:

в соответствии с положениями:

01Note*

07Σημείωση*

08Nota*

according to the Certificate<C>.

wie in <A> aufgeführt und von positiv

beurteilt gemäß Zertifikat<C>.

tel que défini dans <A> et évalué positivement par

02Hinweis*

03Remarque*

09Примечание*

10Bemærk*

conformément au Certificat<C>.

zoals vermeld in <A> en positief beoordeeld door

overeenkomstig Certificaat<C>.

como se establece en <A> y es valorado

positivamente por de acuerdo con el

Certificado<C>.

04Bemerk*

05Nota*

3P459951-2

Table of contents

1 About the documentation 3

1.1 About this document.................................................................. 3

2 About the box 4

2.1 Indoor unit ................................................................................. 4

2.1.1 To remove the accessories from the indoor unit......... 4

3 Preparation 4

3.1 Preparing installation site .......................................................... 4

3.1.1 Installation site requirements of the indoor unit .......... 4

3.2 Preparing water piping .............................................................. 4

3.2.1 To check the water volume and flow rate ................... 4

3.3 Preparing electrical wiring ......................................................... 5

3.3.1 Overview of electrical connections for external and

internal actuators ........................................................ 5

4 Installation 5

4.1 Opening the units ...................................................................... 5

4.1.1 To open the indoor unit............................................... 5

4.1.2 To open the switch box cover of the indoor unit ......... 5

4.2 Mounting the indoor unit............................................................ 6

4.2.1 To install the indoor unit.............................................. 6

4.3 Connecting the refrigerant piping .............................................. 6

4.3.1 To connect the refrigerant piping to the indoor unit .... 6

4.4 Connecting the water piping...................................................... 7

4.4.1 To connect the recirculation piping ............................. 7

4.4.2 To connect the water piping........................................ 7

4.4.3 To connect the pressure relief valve to the drain........ 9

4.4.4 To fill the water circuit ................................................. 9

4.4.5 To fill the domestic hot water tank .............................. 9

4.4.6 To insulate the water piping........................................ 9

4.5 Connecting the electrical wiring................................................. 9

4.5.1 About electrical compliance ........................................ 9

4.5.2 To connect the electrical wiring on the indoor unit...... 9

4.5.3 To connect the main power supply ............................. 10

4.5.4 To connect the backup heater power supply .............. 11

4.5.5 To connect the user interface ..................................... 12

4.5.6 To connect the shut-off valve...................................... 12

4.5.7 To connect the electrical meters................................. 13

4.5.8 To connect the domestic hot water pump................... 13

4.5.9 To connect the alarm output ....................................... 13

4.5.10 To connect the space heating ON/OFF output ........... 13

4.5.11 To connect the changeover to external heat source... 13

4.5.12 To connect the power consumption digital inputs....... 13

4.5.13 To connect the safety thermostat (normal closed

contact) ....................................................................... 14

4.5.14 To connect the booster heater power supply.............. 14

4.6 Finishing the indoor unit installation .......................................... 14

4.6.1 To fix the user interface cover to the indoor unit......... 14

4.6.2 To close the indoor unit............................................... 14

5 Configuration 15

5.1 Overview: Configuration ............................................................ 15

5.1.1 To access the most used commands ......................... 15

5.2 Basic configuration .................................................................... 16

5.2.1 Quick wizard: Language / time and date..................... 16

5.2.2 Quick wizard: Standard............................................... 16

5.2.3 Quick wizard: Options................................................. 17

5.2.4 Quick wizard: Capacities (energy metering) ............... 18

5.2.5 Space heating control ................................................. 18

5.2.6 Domestic hot water control ......................................... 19

5.2.7 Contact/helpdesk number........................................... 19

5.3 Menu structure: Overview installer settings............................... 20

6 Commissioning 21

6.1 Checklist before commissioning................................................. 21

6.2 Checklist during commissioning ................................................. 21

6.2.1 To check the minimum flow rate .................................. 21

6.2.2 To perform an air purge ............................................... 22

6.2.3 To perform a test run ................................................... 22

6.2.4 To perform an actuator test run ................................... 22

6.2.5 To perform an underfloor heating screed dryout.......... 22

7 Hand-over to the user 23 8 Maintenance and service 23

8.1 Maintenance safety precautions................................................. 23

8.1.1 Opening the indoor unit................................................ 23

8.2 Checklist for yearly maintenance of the indoor unit.................... 23

8.2.1 To drain the domestic hot water tank........................... 24

9 Technical data 25

9.1 Components and dimensions: Indoor unit.................................. 25

9.2 Piping diagram: Indoor unit ........................................................ 27

9.3 Wiring diagram: Indoor unit ........................................................ 28

9.4 Technical specifications: Indoor unit .......................................... 31

1 About the documentation

1.1 About this document

INFORMATION

Make sure that the user has the printed documentation and ask him/her to keep it for future reference.

Target audience

Authorised installers

Documentation set

This document is part of a documentation set. The complete set consists of:

▪ General safety precautions:

▪ Safety instructions that you must read before installing ▪ Format: Paper (in the box of the indoor unit)

▪ Indoor unit installation manual:

▪ Installation instructions ▪ Format: Paper (in the box of the indoor unit)

▪ Outdoor unit installation manual:

▪ Installation instructions ▪ Format: Paper (in the box of the outdoor unit)

▪ Domestic hot water tank kit installation manual

▪ Installation instructions ▪ Format: Paper (in the box of the domestic hot water tank kit)

▪ Installer reference guide:

▪ Preparation of the installation, good practices, reference data,… ▪ Format: Digital files on http://www.daikineurope.com/support-

and-manuals/product-information/

▪ Addendum book for optional equipment:

▪ Additional info about how to install optional equipment ▪ Format: Paper (in the box of the indoor unit) + Digital files on

http://www.daikineurope.com/support-and-manuals/productinformation/

Latest revisions of the supplied documentation may be available on the regional Daikin website or via your dealer.

The original documentation is written in English. All other languages are translations.

Technical engineering data

▪ A subset of the latest technical data is available on the regional

Daikin website (publicly accessible).

▪ The full set of latest technical data is available on the Daikin

extranet (authentication required).

EHVH04+08SU18CB6W + EHVH08~16SU26CB6W Daikin Altherma – Low temperature split 4P449980-1B – 2016.11

Installation manual

2 About the box

a~e+h

4×

2×

1×

1× 1× 1× 1×

2× 1×2×

a b c d

f ge

>500

>10>150

(mm)

2 About the box

2.1 Indoor unit

INFORMATION

This unit has been tested and approved according to BSEN12897:2006

2.1.1 To remove the accessories from the indoor unit

1 Remove the screws at the top of the unit. 2 Remove the top panel. 3 Remove the screws at the front of the unit. 4 Push on the button on the bottom of the front plate. 5 Remove the front plate.

WARNING: Sharp edges

Take the front plate on the upper part instead of the lower part. Watch your fingers, there are sharp edges on the lower part of the front plate.

3 Preparation

3.1 Preparing installation site

3.1.1 Installation site requirements of the indoor unit

▪ Mind the following spacing installation guidelines:

▪ The indoor unit is designed for indoor installation only and for

ambient temperatures ranging from 5~35°C.

6 Remove the accessories.

3.2 Preparing water piping

NOTICE

In case of plastic pipes, make sure they are fully oxygen diffusion tight according to DIN 4726. The diffusion of oxygen into the piping can lead to excessive corrosion.

3.2.1 To check the water volume and flow rate

Minimum water volume

Check that the total water volume in the installation is minimum 10 litre for EHVH04+08 and 20 litre for EHVH11+16, the internal water volume of the indoor unit NOT included.

NOTICE

When circulation in each space heating loop is controlled by remotely controlled valves, it is important that the minimum water volume is guaranteed, even if all of the valves are closed.

Minimum flow rate

Check that the minimum flow rate (required during defrost/backup heater operation) in the installation is guaranteed in all conditions.

NOTICE

When circulation in each or certain space heating loops is controlled by remotely controlled valves, it is important that the minimum flow rate is guaranteed, even if all valves are closed. In case the minimum flow rate cannot be reached, a flow error 7H will be generated (no heating/operation).

See the installer reference guide for more information.

a General safety precautions

b Addendum book for optional equipment

c Indoor unit installation manual

7 Reinstall the top panel and the front plate.

Installation manual

d Operation manual

e Sealing ring for shut-off valve

f Shut-off valve g User interface cover h 2 screws for fixing the user interface.

Minimum required flow rate

04+08 models 12l/min 11+16 models 15l/min

See the recommended procedure as described in "6.2 Checklist

during commissioning"on page21.

EHVH04+08SU18CB6W + EHVH08~16SU26CB6W

Daikin Altherma – Low temperature split

4P449980-1B – 2016.11

4 Installation

4×

2×

4×

3.3 Preparing electrical wiring

3.3.1 Overview of electrical connections for external and internal actuators

Item Description Wires Maximum

Outdoor unit and indoor unit power supply

1 Power supply for

outdoor unit

2 Power supply and

2+GND or 3+GND

3 interconnection cable to indoor unit

3 Power supply for

See table below. — backup heater

3a Power supply for

2+GND booster heater

4 Preferential kWh rate

2 power supply (voltage free contact)

5 Normal kWh rate power

2 6.3A supply

User interface

6 User interface 2

Optional equipment

11 Power supply for

2 bottom plate heater

12 Room thermostat 3 or 4 100mA 13 Outdoor ambient

2 temperature sensor

15 Heat pump convector 4 100mA

Field supplied components

16 Shut-off valve 2 100mA 17 Electricity meter 2 (per meter) 18 Domestic hot water

2 pump

19 Alarm output 2 20 Changeover to external

2 heat source control

21 Space heating

2 operation control

22 Power consumption

digital inputs

23 Safety thermostat 2

(a) Refer to name plate on outdoor unit. (b) Minimum cable section 0.75mm². (c) Cable section 2.5mm². (d) Cable section 0.75mm² till 1.25mm²; maximum length:

50m. Voltage-free contact shall ensure the minimum applicable load of 15VDC, 10mA.

(e) Cable section 0.75mm² till 1.25mm²; maximum length:

500m. Applicable for both single user interface and dual user interface connection.

2 (per input

signal)

NOTICE

More technical specifications of the different connections are indicated on the inside of the indoor unit.

(a)

(c)

(d)

(e)

(b)

(d)

running

current

(b)

4 Installation

4.1 Opening the units

4.1.1 To open the indoor unit

1 Loosen and remove the screws at the bottom of the unit. 2 Push on the button at the bottom of the front plate.

WARNING: Sharp edges

Take the front plate on the upper part instead of the lower part. Watch your fingers, there are sharp edges on the lower part of the front plate.

3 Slide the front panel of the unit downwards and remove it.

CAUTION

The front panel is heavy. Be careful NOT to jam your fingers when opening or closing the unit.

4 Loosen and remove the 4 screws that fix the top panel. 5 Remove the top panel from the unit.

4.1.2 To open the switch box cover of the indoor unit

Backup heater

type

*6W 1× 230V 2+GND + 2 bridges

Power supply Required number of

conductors

3× 230V 3+GND + 1 bridge 3× 400V 4+GND

EHVH04+08SU18CB6W + EHVH08~16SU26CB6W Daikin Altherma – Low temperature split 4P449980-1B – 2016.11

Installation manual

4 Installation

120kg

4×

≤1°

0°

1°1°

b a

4.2 Mounting the indoor unit

4.2.1 To install the indoor unit

1 Lift the indoor unit from the pallet and place it on the floor.

2 Slide the indoor unit into position. 3 Adjust the height of the leveling feet to compensate for floor

irregularities. The maximum allowed deviation is 1°.

4.3 Connecting the refrigerant piping

See the outdoor unit installation manual for all guidelines, specifications and installation instructions.

4.3.1 To connect the refrigerant piping to the indoor unit

1 Connect the liquid stop valve from the outdoor unit to the

refrigerant liquid connection of the indoor unit.

a Refrigerant liquid connection b Refrigerant gas connection

2 Connect the gas stop valve from the outdoor unit to the

refrigerant gas connection of the indoor unit.

NOTICE

Do NOT tilt the unit backwards:

Installation manual

EHVH04+08SU18CB6W + EHVH08~16SU26CB6W

Daikin Altherma – Low temperature split

4P449980-1B – 2016.11

4 Installation

4×

180°

260 l

180 l

b a c

c a b

4.4 Connecting the water piping

4.4.1 To connect the recirculation piping

Prerequisite: Only required if you need recirculation in your system.

1 Loosen and remove the 4 screws that fix the top panel. 2 Remove the top panel from the unit.

3 In case of a unit with a tank capacity of 180 l, remove the

expansion vessel.

4 Remove the top insulation. 5 Cut out part (c) from the top insulation.

Tank capacity Cut out position

180l Left OR right 260l Backside

INFORMATION

The water piping needs to comply with section G3 of the Building Regulations. To facilitate compliance, domestic hot water tank kits EKVSU180A and EKVSU260A are available. The instructions below include the installation of these tank kits. If they are NOT used, at all times make sure that the water piping complies with the applicable legislation.

INFORMATION

If you have to inspect the inside of the domestic hot water tank, you can access it via the booster heater boss.

The connection of the water piping involves: ▪ Directly to the indoor unit: connecting the water piping to the

space heating inlet, the space heating outlet, and the domestic hot water outlet.

▪ Via the domestic hot water tank kit: connecting the water piping

to the unit’s domestic cold water inlet, and connecting the kit itself to the drain.

Directly to the indoor unit

INFORMATION

EKVSU260A only: to facilitate maintenance and service, the space heating and domestic hot water outlets (a and c), as well as the space heating inlet (b), can be extended by way of the extension pieces that are delivered with the domestic hot water tank kit. Make sure to use the sealings for the extension pieces (delivered as accessory).

6 Connect the recirculation piping to the recirculation connection

(b) and route the piping through the hole at the backside of the unit (a).

a Piping intake hole b Recirculation connection c Cut-out location

7 Reattach the top insulation and the expansion vessel.

4.4.2 To connect the water piping

NOTICE

Do NOT use excessive force when connecting the piping. Deformation of the piping can cause malfunctioning of the unit.

To facilitate service and maintenance, 2 shut-off valves are provided. Mount these valves on the space heating water inlet and space heating water outlet. Mind their position. The orientation of the integrated drain and fill valves is important for servicing.

1 Install the shut-off valves on the space heating water pipes.

a Space heating water out b Space heating water in c Domestic hot water out

NOTICE

It is recommended to install shut-off valves to domestic cold water in and domestic hot water out connections. These shut-off valves are field supplied.

2 Screw the indoor unit nuts on the shut-off valves. 3 Connect the domestic hot water out pipe to the indoor unit.

EHVH04+08SU18CB6W + EHVH08~16SU26CB6W Daikin Altherma – Low temperature split 4P449980-1B – 2016.11

Installation manual

4 Installation

4×

180 l 260 l

≤600 mm

≥300 mm

Via the domestic hot water tank kit

4 Mount the indoor unit height extension that is part of the kit

(EKVSU260A only).

5 Mount the domestic hot water tank kit.

8 Connect the discharge pipe to the tank kit’s pressure relief

valve, then connect the tundish to the discharge pipe (both discharge pipe and tundish are delivered with the tank kit).

WARNING

Install the tundish away from any electrical device.

Possible consequence: Electric shock or fire.

NOTICE

To ensure a free water flow through the discharge pipe, manually operate the pressure relief valve by turning its knob left.

9 Connect the 2 tundishes (1 from the pressure relief valve of the

domestic hot water tank, and 1 from the pressure relief valve of the domestic hot water tank kit) to an appropriate drain according to the applicable legislation. The following example shows discharge below fixed grating (Building Regulation G3 section 3.61 gives alternative points of discharge):

6 Route the flexible hoses of the domestic hot water tank kit

according to the illustration below.

7 Connect one flexible hose (a) of the domestic hot water tank kit

to the domestic cold water inlet of the indoor unit. Connect the other flexible hose (b) to the cold water supply.

Installation manual

a To indoor unit domestic cold water inlet

b To cold water supply

c Sealings for the flexible hoses of the domestic hot water

tank kit (24×17×2 mm)(delivered as accessory)

a Safety device (pressure relief valve of domestic hot water

tank; pressure relief valve of domestic hot water tank kit)

b Tundish c Fixed grating

d Trapped gully D1 Metal discharge pipe from safety device to tundish D2 Discharge pipe from tundish, with continuous fall. See

Building Regulation G3 section 3.56, Table 03 and worked example.

NOTICE

Install air purge valves at all local high points.

EHVH04+08SU18CB6W + EHVH08~16SU26CB6W

Daikin Altherma – Low temperature split

4P449980-1B – 2016.11

4 Installation

a b+c

b+c

4.4.3 To connect the pressure relief valve to the drain

The blow out of the pressure relief valve is coming out of the backside of the unit.

a Pressure relief blow-out

The blow out should be connected to an appropriate drain according to the applicable legislation. It is recommended to use a tundish.

4.4.4 To fill the water circuit

1 Connect the water supply hose to the fill valve.

4.4.6 To insulate the water piping

The piping in the complete water circuit MUST be insulated to prevent condensation and reduction of the heating capacity.

If the temperature is higher than 30°C and the humidity is higher than RH 80%, the thickness of the insulation materials should be at least 20 mm to prevent condensation on the surface of the insulation.

4.5 Connecting the electrical wiring

DANGER: RISK OF ELECTROCUTION

WARNING

ALWAYS use multicore cable for power supply cables.

4.5.1 About electrical compliance

See "4.5.4 To connect the backup heater power supply" on

page11.

4.5.2 To connect the electrical wiring on the indoor unit

1 To open the indoor unit, see "4.1.1To open the indoor unit"on

page5 and "4.1.2 To open the switch box cover of the indoor unit"on page5.

2 Wiring should enter the unit from the top:

3 Routing of the wiring inside the unit should be as follows: 2 Open the fill valve. 3 Make sure that the automatic air purge valve is open (at least 2

turns).

4 Fill the circuit with water until the manometer indicates a

pressure of ±2.0bar.

5 Purge as much air as possible from the water circuit. 6 Close the fill valve. 7 Disconnect the water supply hose from the fill valve.

4.4.5 To fill the domestic hot water tank

1 Open every hot water tap in turn to purge air from the system

pipe work.

2 Open the cold water supply valve. 3 Close all water taps after all air is purged. 4 Check for water leaks. 5 Manually operate the pressure relief valve of the domestic hot

water tank to ensure a free water flow through the discharge pipe.

NOTICE

To operate the system, the domestic hot water tank needs to be filled completely. Turning on the system when the tank is not full can damage the integrated booster heater and cause electrical errors.

4 Fix the cable with cable ties to the cable tie mountings to

ensure strain relief and to make sure that it does NOT come in contact with the piping and sharp edges.

INFORMATION

To access the domestic hot water temperature sensor, the switch box can be tilted. The switch box should NOT be removed from the unit.

EHVH04+08SU18CB6W + EHVH08~16SU26CB6W Daikin Altherma – Low temperature split 4P449980-1B – 2016.11

Installation manual

4 Installation

X1M

1 2 3

X2M

X5M

X6YB

X6YA

X6Y

X1A X19A

30 31

X1M

1 2 3

1 2

L N

L N 3

X2M

X5M

X6YB

X6YA

X6Y

X1A X19A

S1S

30 31

3 4

abc

Routing Possible cables (depending on unit type and installed options)

Low voltage

High voltage power supply

High voltage control signal

▪ Preferential power supply contact ▪ User interface ▪ Power consumption digital inputs (field supply) ▪ Outdoor ambient temperature sensor (option) ▪ Indoor ambient temperature sensor (option) ▪ Electrical meters (field supply) ▪ Safety thermostat (field supply) ▪ Interconnection cable ▪ Normal kWh rate power supply ▪ Preferential kWh rate power supply ▪ Power supply for backup heater ▪ Power supply for booster heater (in DHW tank) ▪ Power supply for bottom plate heater (option) ▪ Heat pump convector (option) ▪ Room thermostat (option) ▪ Shut-off valve (field supply) ▪ Domestic hot water pump (field supply) ▪ Alarm output ▪ Changeover to external heat source control ▪ Space heating operation control

CAUTION

Do NOT push or place redundant cable length in the unit.

4.5.3 To connect the main power supply

1 Connect the main power supply.

In case of normal kWh rate power supply

Legend: see illustration below.

In case of preferential kWh rate power supply

Connect X6Y to X6YB.

a Interconnection cable (=main power supply) b Normal kWh rate power supply c Preferential power supply contact

2 Fix the cable with cable ties to the cable tie mountings.

INFORMATION

In case of preferential kWh rate power supply, connect X6Y to X6YB. The necessity of separate normal kWh rate power supply to indoor unit (b) X2M30/31 depends on the type of preferential kWh rate power supply.

Separate connection to the indoor unit is required:

▪ if preferential kWh rate power supply is interrupted

when active, OR

▪ if no power consumption of the indoor unit is allowed at

the preferential kWh rate power supply when active.

INFORMATION

The preferential kWh rate power supply contact is connected to the same terminals (X5M/3+4) as the safety thermostat. It is only possible for the system to have EITHER preferential kWh rate power supply OR a safety thermostat.

Installation manual

EHVH04+08SU18CB6W + EHVH08~16SU26CB6W

Daikin Altherma – Low temperature split

4P449980-1B – 2016.11

+ 22 hidden pages