Cub Cadet EX2900, EX3200 User Manual

Ex2900 / Ex3200 ATTACHMENTS

CL300 Loader
Curved boom is constructed from 2” x 5” A500 structural steel, one-piece beam.

A 4” x 2” A500 structural steel torque beam attaches the curved boom beams
together. Features a heavy-duty 5 cu. ft. bucket with reinforced wear plates.
Curved boom design allows for bucket visibility and clear sight lines.
QuickAttach™ system also included.

CB75 Backhoe
QuickAttach™ system allows you to install or remove the backhoe in minutes as it

sets in the cradle with two locking pins. Single Power Beyond kit powers the
backhoe for reliability, control and smooth operation. Dual swing cylinders allow
for precise control of backhoe along foundations and provide more power for
backfilling. Curved boom assembly gives the operator better sight lines when
digging.

MM60RS Mid-Mount Mower
Mid-mount 60” deck with superior vacuum for a cleaner cut. Features an 11-

gauge stamped reinforced deck edge and cast-aluminum gearbox housing with
long-lasting Timken® tapered bearings. Cast-aluminum spindle housings with
7/8” shaft allows for cooler operation. Pulleys are machined from one piece of
steel for balance, reducing vibration and wear to the shaft. Marbane high-lift
blades harden to a Rockwell 50 rating. This extends the life of the blade while
giving a clean cut. QuickAttach™ system allows the deck to be installed and
removed quickly by using J-pins. SmartJet™ deck wash system allows a garden
hose to be attached to the deck cleaning.

FM60/FM72 Rear Finishing Mower
Features an 10-gauge deck housing and reinforcement plate under the spindle

assembly. Rear discharge disperses cuttings cleanly and evenly. Comes with a
wide range of cutting heights from 1” to 4” for clean cuts on all lawns. Gearbox is
highly engineered and rugged with straight-cut gears, casted cooling fins and
completely enclosed seals. The 4 durable composite rubber caster wheels give a
perfectly level cut while eliminating the worry of flat tires. Category 1, full floating
deck allows the mower to follow the contours of the land.

Ex2900 / Ex3200 ATTACHMENTS

RB72 72” Rear Blade
The ½” steel A-frame is welded to two 4” x 4” steel beams with ¼” thick walls

that are fully reinforced. The rotation plate is constructed from 5/8” thick steel.
The 5 forward and 5 reverse positions allows for precise and consistent
grading. The angling plate is constructed from ¼” steel. The 4” outer tubes and

3.5” inner tube with ¼” thick walls are center cap welded. The 3-position tilt
adjustment provides a wide range of applications. The ¼” rolled moldboard is
attached by a ¼” mounting plate. The ½” x 6” cutting edge is hardened for long
life and reversible for even greater life expectancy.

LR60/LR72 Landscape Rake
The A-frame is constructed from ¼” steel welded to a 3” x 3-1/4” beam for

durability and precise control of the attachment. The rotation plate is
constructed from ½” steel. The 5 forward and 5 reverse positions add
versatility for a wide variety of chores. The superior construction of the ¾”
steel angle iron mounting plate gives rigid support to the tines. The hardened
tines are 5/16” x 1” and spaced 2” on center for a high resistance to wear and a
cleaner collection of material.

RT66 66” Tiller
Features a smooth manual shift; shifts out to 56” allowing for cleaner sight

lines when working close to objects or reaching under objects. Quick-adjust
skid shoes adjust up to a depth of 7-1/4” deep. Reinforced #80R lateral chain
drive has exceptional tensile strength. The ¼” steel wear plates on the chain
case allow it to be in contact with the soil while protecting it. High carbon rotor
shaft allows for deeper working depth and greater longevity of the rotor shaft.
Outwardly turned blades keep the rotor supports clean and maximize working
depth.

PHD200 Post Hole Digger
Heavy-duty, 2-7/8” x ¼” walled construction of the boom and 2-3/8” x ¼” wall

yoke allow for extra strength in all soil conditions. Grade 2 shear bolt provides
greater protection to the tractor drive and gearbox assembly. Reinforced
mounting collar with double flighting keeps the auger end from wearing out.
Hardened replaceable cutting knives allow for fast, clean digs and easy
maintenance. Dependable cast-iron gearbox with 540 RPM gives constant
digging power. Large 2” output shaft allows for long life in any soil condition.