Craftsman 13953876 Owner’s Manual

E/.4/RtS

OWNER'S

INSTRUCTIONS

Multi-Function Keyless Entry

MODEL 139.53876

r

Features

:or use with any 53000 SRT series garage door opener
receiver

Personalized Code: Up to 10,000 possible combinations,

Code can easily be changed if desired

Operation: Opener activates when 4-code digits and
ENTER button are pressed,

The keypad will illuminate for 5 seconds at the first push of

any key If wrong numbers are accidentally pressed,
correction can be made immediately The ENTER key will

transmit only the last four digits,

The keypad will blink for 15 seconds after the code is

transmitte& Dudng that time you can STOP or REVERSE
door travel just by pressing the ENTER key,

The Lock feature on openers with premium door controls, is
designed to prevent operation of the door from p_dable

transmitters However, the door will open and close from
the door control push button and the Multi-Function Keyless

Entry
Power Supply: 9 Volt battery

Programming the Code

We recommend that you program your personal code
now, before you install the Multi-Function Keyless Entry.
Then you CaRtest the reception at the mounting location

before you proceed further.

'_Lift the cover to access the keypad, Figure 1. Decide on a

4-digit code using numbers from 0 to 9 You can use a
number more than once (for example, 4, 0, 4, 1).

2. Press the selected code digits on the keypad; then press
and HOLD the ENTER button, and press the SRT button

on the opener end panel (behind the Control Center for

screwdrive), Figure 2,

3 Depending on your opener model, when you Figure 1

press the SRT button eitherthe opener
light(s) will flash or the garage door

will begin to move Retease the

ENTER button

The opener has now tearned the
selected code and witl respond to future keypad

commands.
To ensure that your portable remote control codes

were not disturbed while you were programming the Keyless

Entry, test your remotes and reprogram them if necessary°

To change the code In your Keyless Entry at any time,

repeat Steps 1--3.

GARAGE DOOR OPENER

(WITH SRT BUTTON)

Green "SRT"

Button

Green thdical,3r

% % []

Figure 2 Ligh!

To comply with FCC rules, adjustment or modification of receiver a'ndtot]
itartsmltter is prohibited, except I'or changing the code setting and replacing the |

transmitIer battery THERE ARE NO OTHER USER SERVICEABLE PARTS J

Children operating or playing with a garage door opener
can Injure themselves or others. The garage door could
close and cause serious Injury or death. Do not allow
children to operate the door push button(s) or remote
control(s).

A moving garage door could injure or klll someone under
It. Activate the opener only when you can see the door

clearly, tt is free of obstructions, and Is properly adjusted,

............ i ,,,=,,,i i

Installation

The recommended mounting locations for sectional and one-
piece doors are shown in Figure 3. You can select another
location if you preler However, the keypad must be
installed within sight of the door.

For a one-piece door, use the optional location shown in
the illustration (on the edge of the door jamb) to avoid
injury as the door swings up and out.

Test the reception of the

#..

Keyless Entry by
operating your opener

from the selected
location,Change the

location if necessary.
Open the keypad and

remove the battery

compartment screw and
cover to access the

bottom mounting hole
(Figure 4)

',- (Optiooal Loc_tion

I'(EYPAD MUST BE INSTALLED

WITHIN StGHT OF THE DOOR

Extedor Front Wall

1,,Piece or

Sectional Door

Doer ,Jamb Edge

Io¢ 1-Piece Door)

Door Jamb Face

SECTIONAL DOOR ONLY

Center the keypad at
eye level against the
selected location Mark 4 1/4' up the

Figure 3

centedine from the bottom and drill a

t/8" pi!ot hole lnstalt top mounting
screw, aIIowJng1/8" to protrude
above surface. Position keypad on
screw head and adjust for snug fit

With cover open so bottom mounting
hole is visible, use a punch to mark

hole. Remove keypad and drill 1/8"

pilot hole. Replace keypad and
complete installationwith bottom

screw, using care to avoid cracking
plastichousing Do not overtighten

Replace the battery cover

Battery: The 9 Volt battery should produce

Figure 4

power for at least one year Repface when

keypad illumination becomes dim

1t 4A1970 AIt Rights Reserved Printed in Mexico

© ;995 Sears Roebuck & Company